Search NASA⌕ Search

Engineering topics

Warmack, Robert J Bruce

Publications and source records attributed to Warmack, Robert J Bruce.

Interdiffusion in Ternary Magnesium Solid Solutions of Aluminum and Zinc

Al and Zn are two of the most common alloying elements in commercial Mg alloys, which can improve the physical properties through solid solution strengthening and precipitation hardening. Diffusion plays a key role in the kinetics of these and other microstructural design relevant to Mg-alloy development. However, there is a lack of multicomponent diffusion data available for Mg alloys. Through solid-to-solid diffusion couples, diffusional interactions of Al and Zn in ternary Mg solid-solution at 400° and 450 °C were examined by an extension of the Boltzmann-Matano analysis based on Onsager s formalism. Concentration profiles of Mg-Al-Zn ternary alloys were determined by electron probe microanalysis, and analyzed to determine the ternary interdiffusion coefficients as a function of composition. Zn was determined to interdiffuse the fastest, followed by Mg and Al. Appreciable diffusional interactions among Mg, Al, and Zn were observed by variations in sign and magnitude of cross interdiffusion coefficients. In particular, Zn was found to significantly influence the interdiffusion of Mg and Al significantly: the and ternary cross interdiffusion coefficients were both negative, and large in magnitude, in comparison to and , respectively. Al and Mg were observed influence the interdiffusion of Mg and Al, respectively, with positive and interdiffusion coefficients, but their influence on the Zn interdiffusion was negligible.

36 MATERIALS SCIENCE↗

Fast Acting Eddy Current Driven Valve for Massive Gas Injection on ITER

Tokamak plasma disruptions present a significant challenge to ITER as they can result in intense heat flux, large forces from halo and eddy currents, and potential first-wall damage from the generation of multi-MeV runaway electrons. Massive gas injection (MGI) of high Z material using fast acting valves is being explored on existing tokamaks and is planned for ITER as a method to evenly distribute the thermal load of the plasma to prevent melting, control the rate of the current decay to minimize mechanical loads, and to suppress the generation of runaway electrons. A fast acting valve and accompanying power supply have been designed and first test articles produced to meet the requirements for a disruption mitigation system on ITER. The test valve incorporates a flyer plate actuator similar to designs deployed on TEXTOR, ASDEX upgrade, and JET [1 3] of a size useful for ITER with special considerations to mitigate the high mechanical forces developed during actuation due to high background magnetic fields. The valve includes a tip design and all-metal valve stem sealing for compatibility with tritium and high neutron and gamma fluxes.

Fast Acting Eddy current↗

Al and Zn Impurity Diffusion in Binary and Ternary Magnesium Solid-Solutions

Magnesium alloys are considered for implementation into structural components where energy-efficiency and light-weighting are important. Two of the most common alloying elements in magnesium alloys are Aluminum and Zinc. The present work examines impurity diffusion coefficients of Al and Zn in Mg(Zn) and Mg(Al) binary solid solutions, respectively. Experimental investigation is carried out with ternary diffusion couples with polycrystalline alloys. Concentration profiles were measured by electron microprobe micro-analysis and the impurity diffusion coefficients were determined by the Hall Method. Results of Al and Zn impurity diffusion in Mg solid solutions are reported, and examined as a function of composition of Mg solid solution.

aluminum↗

Secondary Ion Mass Spectrometry for Mg Tracer Diffusion: Issues and Solutions

A Secondary Ion Mass Spectrometry (SIMS) method has been developed to measure stable Mg isotope tracer diffusion. This SIMS method was then used to calculate Mg self- diffusivities and the data was verified against historical data measured using radio tracers. The SIMS method has been validated as a reliable alternative to the radio-tracer technique for the measurement of Mg self-diffusion coefficients and can be used as a routine method for determining diffusion coefficients.

diffusion↗

Foreword for Non-Dispersive Infrared (NDIR) Gas Measurement Today

Infrared spectroscopy provides the analytical laboratory with essential capabilities to identify and to quantify components of gas mixtures in a relatively straightforward manner. Except for symmetric diatomic species, most molecules are 'IR active' that is, they absorb IR light at specific energies associated with that molecule's vibrational and rotation modes. Simple molecules have a few predominant absorption energies and are easy to identify, while more complicated molecules with many bonds have many absorption peaks. To cover the full range of possible absorption energies, laboratory instruments initially employed dispersive elements, typically gratings, to scan over the wavelengths of interest. Today, Fourier-transform infrared (FTIR) spectroscopy has replaced most dispersive IR spectrometry due to improvements in speed and the signal-to-noise ratio but at the expense of instrumental complexity. The impressive analytical power of IR spectroscopy can be distilled into a tiny sensor for a restricted, but nevertheless very useful, set of chemical vapors. Non-dispersive infrared (NDIR) sensors use bandpass filters to select one, or at most a few, energy bands corresponding absorption by carbon dioxide, water, hydrocarbons, etc. Although the concept is simple, the task has proved to be elusive for constructing an NDIR sensor that maintains its calibration in spite of aging and environmental factors. Over the past four decades, Dr. Wong has been on the quest to perfect NDIR sensing, yet in very practical designs. This book reflects his journey, and more recently that of his coauthor, to do just that.

99 GENERAL AND MISCELLANEOUS↗