Search NASA⌕ Search

DOE OSTI · 1185370

Al and Zn Impurity Diffusion in Binary and Ternary Magnesium Solid-Solutions

Abstract

Magnesium alloys are considered for implementation into structural components where energy-efficiency and light-weighting are important. Two of the most common alloying elements in magnesium alloys are Aluminum and Zinc. The present work examines impurity diffusion coefficients of Al and Zn in Mg(Zn) and Mg(Al) binary solid solutions, respectively. Experimental investigation is carried out with ternary diffusion couples with polycrystalline alloys. Concentration profiles were measured by electron microprobe micro-analysis and the impurity diffusion coefficients were determined by the Hall Method. Results of Al and Zn impurity diffusion in Mg solid solutions are reported, and examined as a function of composition of Mg solid solution.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Kammerer, Catherine, Kulkarni, Nagraj S, Warmack, Robert J Bruce, Sohn, Yong Ho. 2014-01-01. Al and Zn Impurity Diffusion in Binary and Ternary Magnesium Solid-Solutions. https://www.osti.gov/biblio/1185370

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Electrocoagulation in Water Treatment: Targeted Contaminant Removal and Laboratory Best Practices

Electrocoagulation for water treatment offers many advantages over traditional treatment technologies, including improved energy efficiency and modularity. One challenge with electrocoagulation is the lack of standardization in the methodology and reporting. This review provides a novel contribution by examining the past literature using a uniform metric (charge loading) as a basis for comparison, highlighting the importance of uniform reporting practices in this field. Furthermore, this review provides practical guidance for experimentalists in standardizing the electrocoagulation design and operating procedures. First, we present a comprehensive overview of contaminant-specific electrocoagulation as an electrochemical treatment technology for processing industrial, municipal, and agricultural water, with a focus on aluminum and iron electrocoagulation. We detail the fundamental mechanisms that allow for constituent removal during pretreatment. Specifically, we highlight electrocoagulation’s potential for organics, metalloids, microbes, and hardness remediation, examining the optimal removal conditions in terms of charge loading and current density. We conclude this work with some experimental best practices for lab-scale electrocoagulation experiments.

aluminum↗

Low-Temperature Pyrolysis of Aliphatic Polymers Using a Fluorinated Amorphous Silica–Alumina: Cooperative Reactivity between a Redox-Active Radical and an Aluminum Lewis Site

Fluorinated amorphous silica–alumina (F-ASA) prepared by the thermolysis of Krossing’s Al(OC(CF 3 ) 3 ) 3 (PhF) Lewis superacid supported on silica is a very reactive catalyst that promotes the pyrolysis (cracking) of aliphatic polymer melts to produce low molecular weight hyperbranched oils. Initial spectroscopic studies reported previously (Gao, J.; Perras, F. A.; Conley, M. P. J. Am. Chem. Soc . 2025 , 147, 18145–18154) showed that this material contains a distribution of four-, five-, and six-coordinate aluminum sites and a small amount of Brønsted acid sites, similar to typical amorphous silica–alumina materials that are far less reactive in the pyrolysis of aliphatic polymer melts. The objective of this study was to determine whether other active sites present in F-ASA could facilitate pyrolysis reactions. This study provides evidence for the presence of a redox-active silicon oxycarbide persistent radical ((≡Si) 3 C•) in F-ASA. Mims ENDOR EPR experiments show that (≡Si) 3 C• is located close to aluminum. Contacting F-ASA with thianthrene (Th) results in oxidation to form the [Th •+ ][F–ASA] ion-pair, while reactions with 1-hydroxy-2,2,6,6-tetramethylpiperidine (TEMPOH) result in H atom transfer to form TEMPO radical and F-ASA-H containing a mildly acidic (≡Si) 3 C–H. Poisoning studies show that both Lewis acidity and (≡Si) 3 C• are required for polymer pyrolysis reactivity. Finally, we propose that F-ASA promotes the formation of alkyl radicals in polymer melts, which are key intermediates in the thermal pyrolysis reactions of aliphatic polymers, involving the cooperative reactivity of both the Lewis acid and (≡Si) 3 C•.

aluminum↗

The chlorination and separation of aluminum using low-temperature sulfur chloride reagents

There is currently no strategy for the permanent waste disposal or recycling for used nuclear fuelsfrom research reactors. For this reason, low-temperature reactions have been developed for thechlorination of the Al alloys and subsequent separation from used nuclear fuels to reducethe volume of high-level waste in storage. Three sulfur chloride reagents – S 2 Cl 2 , SOCl 2 , and SO 2 Cl 2 —were tested, and two were found to quantitatively chlorinate Al metal and Al alloys undermild conditions. Further, these low-temperature reactions proceed between 298 and 411 K, and up to 5 gof metal is chlorinated in 1–3 h. Preliminary results indicate that the reactivity and exothermicity ofthe reaction between the Al and sulfur chloride reagents is highly dependent on the surface area-to-volume ratio of the metal and the volume of solvent. Elemental S is produced as a by-productduring the chlorination with S 2 Cl 2 but can be quantitatively rechlorinated under mild conditions toregenerate the initial chlorination reagent. Therefore, in this case, chlorine is the only elementconsumed in the reaction, thus minimizing the waste generated during the chlorination process.The AlCl 3 may then be separated from other materials present in Al 6061 or Al 8001 because of itshigh solubility in the sulfur chloride reagents. This process may also be extended to chlorinate Alfrom research reactor fuels.

aluminum↗