Search NASA⌕ Search

Engineering topics

Wesley L Johnson

Publications and source records attributed to Wesley L Johnson.

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Cryogenic Fluid In-Situ Liquefaction for Landers: Prototype Demonstration

As the advancement of In-Situ Resource Utilization concepts and systems continue to develop, applicable technology development and maturation continues in parallel. While there are many different ways to use the resources found on other bodies, one of the most prevalent suggested applications is the manufacturing of propellants. One of the key technologies for the eventual use of these propellant production based ISRU systems is the liquefaction and storage of the produced propellants. The most mentioned propellant combinations include oxygen-hydrogen and oxygen-methane. The liquefaction of oxygen in these systems will be different than oxygen liquefaction systems on Earth, which mainly revolves around the distillation of air. These systems have been developed conceptually and many of the components have been previously tested or are in development. However, the need to demonstrate the system level operations still exists. The demonstration of a prototypical oxygen liquefaction system using tube-on-tank broad area cooling was completed to better understanding system level operations during liquefaction activities. Demonstration testing included system performance determination, constant liquefaction demonstrations, and transient liquefaction demonstrations. The demonstrations showed the operational capabilities of the tube-on-tank system with an integrated cryocooler. Additional testing explored subsurface vs ullage introduction of the gaseous oxygen flow stream as well as demonstrating a novel fiber optic sensor that measured the temperature gradients along the fluid center line within the tank.

ISRU↗
NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

While oxygen will probably be the first fluid liquefied from in-situ developed propellants, hydrogen will also be a sought-after commodity on both the Lunar and Martian surfaces. General hydrogen liquefaction processes are not significantly affected by the atmosphere on Mars and similar processes can be applied on both surfaces. However, hydrogen will require different processes than oxygen (which can be directly liquefied into its final use tank) due to the different spin states the hydrogen nucleus (i.e. parahydrogen and orthohydrogen) can have as well as the significant sensible energy that has to be removed prior to the actual phase change. Due to the low efficiency of 20 K class cryocoolers and high sensible heat removal requirements at higher temperatures, significant benefits can be obtained by precooling the hydrogen gas in a variety of manners. The benefits of three concepts are explored to take advantage of different precooling technics as well as accounting for sensible, latent, and para to ortho conversion heating requirements. Process concepts are shown that can reduce the base input power requirements for heat removal by more than 67% and the radiator area by similar amounts. A majority of the technology development for these processes has already begun, both within NASA and externally, with the few gaps being identified.

ISRU↗
NASA NTRS2020

Theoretical Limits of Vapor Cooling Large Cylindrical Structures Using Boil-Off

The Structural Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER) is planning to demonstrate the performance benefits of using boil-off to reduce the heat load on various upper stage structural members by using the boil-off vapor to intercept some of the heat load on the structures. A first order simplified analytical model was constructed in order to understand sensitivity of various parameters to performance as well as to understand the theoretical maximum performance of the vapor cooling of a thin-walled cylindrical structure. Constant fluid properties and a temperature dependent thermal conductivity of the structure material were assumed. The model showed that vapor cooling of an aluminum cylindrical structure with hydrogen can reduce the heat load along the cylinder by as much as 70%. Also, cooling a portion of the cylinder is quite effective in comparison with cooling it entirely.

R. Balasubramaniam↗
NASA NTRS2020

Technology Demonstration Mission (TDM) Evolvable Cryogenics (eCryo) Project: Structural Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER) - Test Plan

The initial test of the SHIIVER system includes multilayer insulation and vapor cooled structure. Testing will occur in the In-Space Propulsion Facility (thermal/vacuum) and RATF (acoustic) facilities at Plum Brook Station in Sandusky Ohio. The testing will demonstrate the performance benefits of multilayer insulation and vapor based heat intercept on a “large scale” test article in a manner befitting large upper stages.

Large Scale Hydrogen Testing, Cryogenics, Multilay↗
NASA NTRSDate not supplied

SHIIVER Assemby Thermal Model Prediction for Transient Test Conditions

An integrated thermal model of the Structure Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER) was built in Thermal Desktop/Sinda-Fluint and used to predict thermal performance of the system with the technologies being tested from the eCryo project. The technologies tested include the vapor cooling of the structure using the boil-off and multilayer insulation (MLI) on the hydrogen tank. The thermal model is used to 1) understand system transient behaviors; 2) perform trade studies of different vapor-cooling designs; 3) define the test operations matrix, test procedures, and conditions; and 4) address thermal-related questions at different phases of SHIIVER project. Details of the thermal model are herein described, and results corresponding to the test operations are presented for four different configurations at different fill levels. The thermal performance of each configuration is predicted with the thermal model regarding the heat reduction and boil-off reduction by using vapor cooling and/or MLI on the structures attached to the hydrogen tank.

thermal modeling↗
NASA NTRSDate not supplied

Cryogenic Fluid Management Technologies Enabling for the Artemis Program and Beyond

NASA is endeavoring on an ambitious return to the Moon and eventually on to Mars through the Artemis Program leveraging innovative technologies to establish sustainable exploration architectures collaborating with US commercial and international partners[1]. Future NASA architectures have baselined cryogenic propulsion systems to support lunar missions and ultimately future missions to Mars. NASA has been investing in maturing CFM active and passive storage, transfer, and gauging technologies over the last decade plus primarily focused on ground development with a few small-scale microgravity fluid experiments. Recently, NASA created a Cryogenic Fluid Management (CFM)Technology Roadmap identifying the critical gaps requiring further development to reach a technology readiness level (TRL) of 6 prior to infusion to flight applications. To address the technology gaps the Space Technology Mission Directorate(STMD)strategically plans to invest in a diversified CFM portfolio approach through ground and flight demonstrations ,collaborating with international partners, and leveraging Public Private Partnerships (PPPs) opportunities with US industry through the Tipping Point and Announcement of Collaborative Opportunities (ACO) solicitations. Once proven, these system capabilities will enable the high performing cryogenic propellant systems needed for the Artemis Program and beyond.

Cryogenic Fluid Management↗
NASA NTRSDate not supplied

Results of Use of Heat Flux Sensors on Liquid Hydrogen Tanks

Heat flux sensors were used to characterize the performance of insulation on the Structural Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER), a large-scale test article designed to simulate upper stage cryogenic propellant tank thermal performance in simulated space environments. Usually, the insulation heat loads are derived from calculations removing all other heat sources and attributing the residual heat load to the insulation system. Testing for SHIIVER included the tank being just insulated with spray-on-foam insulation as well as covering the domes with multilayer insulation while leaving the barrel section insulated with spray-on-foam. Heat flux sensors were located at multiple locations on both domes as well as on the barrel section of the tank. Results from the SHIIVER testing using the heat flux sensors are compared to other calculated heat inputs for both liquid nitrogen and liquid hydrogen testing as a function of tank fill level. Further investigation into the transient nature of the SHIIVER testing including the heat flux sensors provided insight into heat flow patterns that may not have been otherwise seen using temperature sensors and calculated insulation heat loads. While the demonstrated uncertainties in the absolute values in the heat flux sensors are high, the values and the trends match well with other calculation methods. The results of SHIIVER allow for the use of heat flux sensors for measurements of insulation performance and dynamic system thermal response for future applications.

Cryogenic Fluid Management↗
NASA NTRSDate not supplied

Cryogenic Fluid In-Situ Liquefaction for Landers: Prototype Demonstration

As the advancement of In-Situ Resource Utilization concepts and systems continue to develop, applicable technology development and maturation continues in parallel. While there are many different ways to use the resources found on other bodies, one of the most prevalent suggested applications is the manufacturing of propellants. One of the key technologies for the eventual use of these propellant production based ISRU systems is the liquefaction and storage of the produced propellants. The most mentioned propellant combinations include oxygen-hydrogen and oxygen-methane. The liquefaction of oxygen in these systems will be different than that on Earth, which mainly revolves around the distillation of air. These systems have been developed conceptually and many of the components have been previously tested or are in development. However, the need to demonstrate the system level operations still exists. The demonstration of a prototypical oxygen liquefaction system using tube-on-tank broad area cooling was completed to better understanding system level operations during liquefaction activities. Demonstration testing included system performance determination, constant liquefaction demonstrations, and transient liquefaction demonstrations. The demonstrations showed the operational capabilities of the tube-on-tank system with an integrated cryocooler. Additional testing explored subsurface vs ullage introduction of the gaseous oxygen flow stream as well as demonstrating a novel fiber optic sensor that measured the temperature gradients along the fluid center line within the tank.

ISRU↗
NASA NTRSDate not supplied

NASA’s Developments in Cryogenic Fluid Management Technology

NASA has been pursuing the development and demonstration of enabling and enhancing technologies for Cryogenic Fluid Management (CFM) in collaboration with the US industry. NASA’s vision for current and future space exploration requires high-performance chemical and nuclear propulsion solutions that utilize cryogens. The Agency will use cryogenic fluids for Earth-to-orbit transportation, human missions to the Moon and Mars, planetary exploration, and in-situ resource utilization (ISRU) production. All these architectures will require state-of-the-art long-duration storage on the surface and in-space transfer for refueling. This paper focuses on key CFM technology developments completed or ongoing by the Cryogenic Fluid Management Portfolio Office within NASA’s Space Technology Mission Directorate. The CFM Portfolio Office, partnered with US aerospace industry, has invested in CFM technology ground and flight demonstrations, focused on maturing CFM hardware and operations for Artemis and Moon to Mars activities. These demonstrations additionally provide NASA with data to inform numerical modeling activities for verification and validation of design tools and approaches for future missions. This paper includes discussion on remaining high-priority open CFM technology gaps for Mar-forward architectures and initiatives for closure.

Cryogenic Fluid Management↗
NASA NTRSDate not supplied

Commercially-viable Hydrogen Aircraft for Reduction of Greenhouse Emissions

NASA assembled a cross-organizational multidisciplinary “radical” project team combining a diverse set of skills including aircraft architecture modelling and optimization, advanced material science, and engineering of high performance cryogenic, thermal management and fuel cell systems components and subsystems to tackle the challenging problem of development of commercially viable mid-size aircraft that would radically transform air transportation. Our team is developing an integrated conceptual and experimental methodology to realize a medium-range hydrogen aircraft design based on fuel cells, hydrogen burning engines, advanced power management and distribution, cryogenic hydrogen storage systems, and novel thermal management systems combined with an integrated aircraft concept of operations both during the flight and at the airports. The resulting analyses suggested the aircraft architecture options, sizes and layouts for the propulsion subsystem and cryogenic liquid hydrogen (LH2) tankage to verify the weight-scaling relationships for a medium-range aircraft carrying 100-200 passengers flying 1000 - 5000 km. Hydrogen - based distributed electric propulsion and cryogenic systems were further analysed, and more detailed study identified systems goals for a viable overall system weight for missions of various lengths. The developed aircraft architecture is being optimized by total specific energy density, specific power, size and mission profiles.

aircraft architecture↗
NASA NTRSDate not supplied

Cryogenic Fuel Aviation – Challenges and Opportunities

NASA aeronautics goals include pioneering new technology to increase efficiency and reduce emissions from air travel. The feasibility of using of on-board cryogenic fuels systems in combination with fuel cells, high efficiency engines, and electric motors for high efficiency commercial transport aircraft is being examined at NASA in collaborations with external partners. Growing emphasis on next generation air transportation resulted in the development of strategic investigations into cryogenic fuels aviation, including roadmaps for maturing new technologies, needs to improve testing and manufacturing capabilities, and the requirements for establishing regulatory and certification standards. A NASA cross-organizational multidisciplinary project team is exploring new aircraft architectures, enabling materials, and the engineering challenges associated with cryogenic fuels for aircraft. The engineering challenges include high performance cryogenic, thermal management, and power/propulsion components and subsystems to tackle the challenging problem of development of commercially viable aircraft that would radically transform air transportation.

liquid natural gas↗