Search NASA⌕ Search

Engineering topics

Wittman, Richard S.

Publications and source records attributed to Wittman, Richard S..

At least 19 records

Improved production and purification of 240Am by deuteron-induced activation of 240Pu target

An optimized method for production of 240Am via the 240Pu(d,2n)240Am reaction is reported. The optimized method produced 7.94 × 108 ± 7% atoms 240Am/mg 240Pu/µA-h. The yield and purity of the products from the optimized method are evaluated in context of the intended application to produce material to measure the cross-section for the 240Am(n,f) reaction. The presented method is also compared with other production methods available in the literature. Keywords—240Am production, deuteron-induced reactions, cross-section, target preparation, post-irradiation purification Abbreviations GEA—Gamma Energy Analysis

Morrison, Erin C.↗

Methods, systems, and computer-readable storage media for enhanced phase-contrast x-ray imaging

Systems and methods that directly image attenuation-based object grid, use a source grid to improve imaging of the object grid using a high-energy polychromatic source, and use a detector grid having gratings oriented substantially orthogonally to that of the object grid, can address artifacts and beam hardening effects that limit the quality and discriminatory power of high-energy x-ray imaging that includes phase contrast.

Miller, Erin A.↗

Quantitative uranium elemental reconstruction using spectral x-ray radiography

X-ray radiography offers the ability to noninvasively inspect the internal structure and material composition of objects. Dual-energy radiography allows material discrimination but is limited in quantitative material measurements due to the broad nature of the interrogating x-ray spectrum. Spectral radiography detectors provide an observation of not just the number of x rays that are transmitted through a sample but also the spectrum. Here, experimental validations of a method to use spectral x-ray radiography to accurately quantify the uranium mass in a powder are presented. An accurate system response model was developed, which includes a model of the incident x-ray source spectrum and a pixel-wise detector response that describes how the transmitted x rays were observed. Further, a calibration to account for the effect of partial x-ray attenuation was developed. As a result, the method is demonstrated to be capable of estimating the uranium mass in a variety of uranium oxide powders to a bias of –0.01±0.62%.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Spectral gratings-based phase-contrast imaging for materials characterization

Spectral X-ray detectors provide a direct observation of the energy spectrum of a transmitted X-ray beam, both for typical and phase-contrast gratings-based systems. The sensitivity of a gratings-based X-ray system to small-angle deflections from a given particle size is dependent on X-ray energy. Therefore, spectral (energy-sensitive) detectors could be sensitive to particle size, even with a broad spectrum from a commercial X-ray generator. Furthermore, these detectors allow direct observation of how the X-ray spectrum is changing as the beam is passing through an object and gratings, and how this affects grating visibilities used to determine the presence of small-angle deflections. This is a particular issue for higher-energy systems where artifacts from beam hardening are common. We present results exploring the particle-size dependent signatures that are available from a spectral gratings-based phase-contrast X-ray imaging system, and the feasibility of observing them with lab-based, broad-spectrum X-ray generators.

Gilbert, Andrew J.↗

Serial Moire scanning phase contrast x-ray imaging

Method include emitting x-rays from an x-ray source, directing a first portion of the x-rays through an object grating situated adjacent to an object while the object is scanned relative to the object grating along a scan direction, directing a second portion of the x-rays through the object and subsequently through a detector grating without transmitting through the object grating, wherein the object grating and detector grating are adjacently arranged in a field of view of the x-rays sequentially with respect to each other in the scan direction, and receiving the first portion transmitted through the object and object grating with a first portion of a detector and receiving the second portion transmitted through the object and the detector grating with a second portion of the detector adjacent to the first portion of the detector. Systems are also disclosed, along with related techniques for beam hardening correction.

Miller, Erin A.↗

Measuring the Electrochemical Corrosion of 233U-doped UO2 in a Microfluidic Device

We have developed a microfluidic, ‘particle-attached microfluidic electrochemical’ device, or PAMEC, that uses microgram quantities of radioactive materials, such as uranium dioxide (UO2), rather than bulk specimens to both observe electrochemical changes and measure spectroscopic properties. The PAMEC device reduces the need for running experiments in a shielded facility and allows for in-operando, real-time investigations of electrochemical properties and morphological changes of micrograms of particles. This novel design offers a promising platform to investigate spent nuclear fuel (SNF) and other nuclear materials under various controlled condition, and to provide insights to nuclear waste management, and fuel performance

Electrochemistry↗

Progress on Associated-Particle Imaging Algorithms, 2022

The present work describes progress on developing imaging algorithms that use fast neutron signatures acquired using the associated-particle imaging (API) method. The present work complements ongoing work to develop neutron source and detector hardware to enable field inspection by investigating algorithms that are capable of discriminating among critical materials or extracting three-dimensional (3D) geometrical information from single-sided or transmission measurements. The present work is divided into three approaches: 1.Iterative reconstruction of inelastic gamma-ray emissions to perform 3D time-of-flight (TOF) imaging in a single view in either transmission or backscatter configurations. Iterative reconstruction enables image resolution better than the inherent TOF resolution. 2.Decomposition of registered neutron and x-ray radiographs into an assumed material list for each pixel in the image. 3.Material identification using full spectral analysis that includes the emergent neutron and gamma ray energies, times, and angles. Progress for each approach is summarized for fiscal year (FY) 2022.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Comparison of model predictions with measured proton-induced production of nickel and iridium isotopes

Calculations were performed to support method development for simultaneous production of Ni and Ir isotopes. Here, the work scope included development of the physical target, irradiation configuration, and post-irradiation radiochemical separations. The assumptions of predictive models previously developed were refined based upon the precise experimental configuration selected, including Os target material and a set of stacked targets for concurrent production of Ni and Ir isotopes. Model predictions of the reaction cross sections with EMPIRE 3.21 and implied isotopic yields are compared with proton beam irradiation measurements to refine model parameters and guide future experiments.

Isotope Production↗

Methods, systems, and computer-readable storage media for enhanced phase-contrast x-ray imaging

Systems and methods that directly image attenuation-based object grid, use a source grid to improve imaging of the object grid using a high-energy polychromatic source, and use a detector grid having gratings oriented substantially orthogonally to that of the object grid, can address artifacts and beam hardening effects that limit the quality and discriminatory power of high-energy x-ray imaging that includes phase contrast.

Miller, Erin A.↗

Configuration and impurity quantification of AmLi sources using radiography and gamma spectroscopy

This paper presents the non-destructive assay of two AmLi sources used for detector characterization and active interrogation at PNNL, identified as MRC-101 and MRC-103. First, a detailed description of the internal configuration of 2724-BT encapsulated MRC sources is established. X-ray radiographs of the AmLi sources are reported for the first time to verify the dimensions and orientation of the encapsulation. Notably, a density variation was observed as a contrast change across the height of the source cavities. Contrary to commonly made assumptions in literature, it is indirectly observed that the AmLi source/target material only occupies a portion of the source cavity. The intensity of the prompt gamma-rays resulting from the inelastic scatter of alpha particles on 7Li was used to calculate the mass ratios of LiH:AmO2. The gamma-ray spectra revealed the presence of numerous impurities in both source and target material (243Am, 237Np, 154Eu, 23Na, and 9Be). Neutron-gamma production ratios were applied to the intensity of the Doppler-broadened peaks from alpha-induced reactions with 7Li, 9Be, and 23Na to calculate neutron rates for both sources. A neutron/alpha production yield (derived in this work) was then related to the atomic concentration of these isotopes to find the approximate masses within each source. Ultimately, the AmLi source density was estimated with prompt gamma analysis based on partial source volumes as 0.45±0.08 g/cm^3.

DTRA, AmLi, neutron↗

Independent Technical Review of INL Aluminum-Clad Spent Nuclear Fuel (ASNF) Oxide Layer Radiolytic Gas Generation Resolution: Task 2

PNNL staff performed an independent technical review (ITR) of the aluminum-clad spent nuclear fuel (ASNF) program Task 2. The objective of Task 2 is to determine G-values for the radiolytic production of gaseous molecular hydrogen (H 2 ) from the aluminum oxyhydroxide layers present on ASNF cladding. The G-values need to be defensible, bounding, but not overly conservative. As part of the ITR, the team reviewed program documents, Task 2 work plans, and results to date. In addition, the team held three separate video conferences with the program research staff to ask clarifying questions and obtain additional detail. The PNNL ITR team concludes that if the program follows the methodology and rigor outlined in the test matrices, the program will develop G-values for a defensible technical basis of extended storage of ASNF. Recommendations for improvement are given.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Detector Characterization for Quantitative Spectral Radiography of Uranium Powder Samples

Pacific Northwest National Laboratory (PNNL) is developing a prototype spectral x-ray radiography (SpecX) non-destructive assay system for noninvasive material mass quantification of uranium-bearing powders. The SpecX system uses a custom material estimation algorithm, which requires a high-fidelity pixel-by-pixel detector response model for accurate quantification. We performed a detailed characterization and built a model of a High-Energy X-ray Imaging Technology (HEXITEC) CdTe pixelated spectral detector. Here we present the detector characterization which led to that model, including a determination of the pixel-wise energy calibration, the detection efficiency, the detector uniformity, the detector stability, and a comparison of methods to remove charge-shared events.

spectral X-ray radiography, pixelated detector, ca↗

Improved Cumulative Fission Yield Measurements with Fission Spectrum Neutrons on 238U

Two isotopically-characterized targets of high-purity (99.961±0.002%) 238U metal and a neutron dosimetry package were exposed to a pulsed neutron irradiation using the Godiva IV critical assembly at the National Criticality Experiments Research Center to measure the integral fission product yields produced in a Watt fission neutron-energy spectrum. Following irradiation, the fissioned targets were counted with two broad energy germanium detectors. Estimates of the total fissions for each target were made using measurements of well-known fission products. The total number of fissions in each target were then used to measure the fission yields of 33 fission products, 18 of which are published as new measurements. Twelve of the 18 isotopes were in agreement with ENDF/B- VIII.0 using the zeta test and treating ENDF/B-VIII.0 as the true mean: 84mBr, 93Y, 94Y, 104Tc, 134I, 135I, 138Xe, 141Ba, 142Ba, 142La, 146Ce, and 149Nd. The ENDF/B-VIII.0 fission yield for 139Ba was only slightly outside of 1-s relative to the uncertainty measured in this work. Uncertainties for 5 fission product yields were markedly improved over those reported in ENDF/B-VIII.0: 128Sn, 129Sb, 130gSb, 131mTe, and 133I. The fission yields measured for 128Sn, 131mTe, and 133I were in good agreement with the ENDF/B-VIII.0 predicted fission yields. However, fission yields measurements of the isotopes 129Sb, and 130gSb deviated from the ENDF/B-VIII.0 value. Both of these isotopes reside near the doubly magic nuclear shell closures of 50 protons and 82 neutrons. These fission yields may be suppressed because of the odd-odd nuclear structure of 130gSb and the odd-even structure of 129Sb and isomer splitting. Comparisons to other recent work and a brief review with citations are included to support this conclusion.

Fission Yields↗

3D Tomography and Image Processing Using Fast Neutrons Final Report

This document is the final report for project OR16-ML-3DTomography-PD3Jb, “3D Tomography and Image Processing Using Fast Neutrons.” This project was motivated by the availability of three-dimensional (3D) tomographic neutron transmission and induced-reaction data following the development of associated-particle imaging (API) systems with two-dimensional (2D) or “area” neutron detectors such as the Advanced Portable Neutron Imaging System, which is capable of simultaneous measurement of transmission and induced-reaction neutrons.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Isolation of Au and Pt radionuclides from deuteron-irradiated platinum using TBP resin

A separation procedure was developed and implemented for the isolation of gold (Au) and platinum (Pt) radionuclides from deuteron irradiated Pt using tri-butyl phosphate (TBP) resin. Results of the procedure demonstrated a Pt recovery of 98 ± 2% and a Au recovery of 92±7%, in their respective fractions (n=4, ±1s). The decontamination factors were 2900 ± 500 for Au removal from the Pt fraction and 830±30 for Pt removal from the Au fraction (n=4, ±1s).

radiochemical separation, deuteron, Tributyl phosp↗

Python Performance Prediction Package for the PGET instrument: User Guide

The Performance Prediction Package (PPP) is a software suite for generating radiation transport results, or leveraging existing transport results, to produce synthetic emission tomography measurements of spent nuclear fuel assemblies. Such synthetic data can be used to mimic specific measurements, and to systematically investigate detection capabilities. Possible uses for the tool include: • Instrument design • Predictive evaluation of observables prior to an inspection visit • Post-measurement assessment of measured data • Evaluation of unusual cases – closed containers with anomalous objects • Sensitivity studies for planning inspections • Sensitivity studies for diversion scenarios • Evaluation of analysis methods A scenario is defined with an assembly type, burnup, and cooling time; as well as assembly rotation angle and position relative to the PGET instrument. Pin-to-pin activity variations or a burnup gradient may be present, but in an inspection scenario these are unlikely to be specified. The measurement will specify a measurement time and a particular detector for detector response, and an optional empirical correction can further adjust the model to better mimic the measurement. The goal is to detect missing pins, or burnup anomalies consistent with a pin substituted with a fresh pin after partial burnup.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Nuclear reactor target assemblies, nuclear reactor configurations, and methods for producing isotopes, modifying materials within target material, and/or characterizing material within a target material

Target assemblies are provided that can include a uranium-comprising annulus. The assemblies can include target material consisting essentially of non-uranium material within the volume of the annulus. Reactors are disclosed that can include one or more discrete zones configured to receive target material. At least one uranium-comprising annulus can be within one or more of the zones. Methods for producing isotopes within target material are also disclosed, with the methods including providing neutrons to target material within a uranium-comprising annulus. Methods for modifying materials within target material are disclosed as well as are methods for characterizing material within a target material.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗