Search NASA⌕ Search

Engineering topics

Wolf, M.

Publications and source records attributed to Wolf, M..

At least 55 records · Page 3

Summary of the high-efficiency crystalline solar cell research forum

An outline is given listing the speeches given in each session and the pertinent points is some speeches. There were six session, besides the overview session they were: (1) high efficiency concepts; (2) surface/interface effects; (3) bulk effects; (4) modeling; and (5) high efficiency device processing. Besides the emphasis placed on increasing efficiency of energy conversion, a great amount of discussion was spent on ways to reduce recombination and reducing surface defects.

Wolf, M.↗

Lifetimes in Si CVD-epitaxial and other layers determined by spectral LBIC

In an effort to evaluate the minority carrier lifetimes in CVD-epitaxially grown layers in their dependence on the CVD process variables, the absolute spectral LBIC method was found to be the only available method capable of yielding both lifetime and surface recombination velocity in layers, independent of the resistivity of this layer or that of the substrate, as long as they are separated by a pn-junction. With this method, it was not only possible to determine the minority carrier lifetimes in as-grown epi-layers, but to observe their changes through the device fabrication processes. In addition, it was possible for the first time to determine the lifetimes in the alloy-regrowth p(+) layers of base high/low junction structures.

Wolf, M.↗

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

It was found that the Solarex metallization design and process selection should be modified to yield substantially higher output of the 10 cm x 10 cm cells, while the Westinghouse design is extremely close to the optimum. In addition, further attention to the Solarex pn junction and base high/low junction formation processes could be beneficial. For the future efficiency improvement, it was found that refinement of the various minority carrier lifetime measurement methods is needed, as well as considerably increased sophistication in the interpretation of the results of these methods. In addition, it was determined that further experimental investigation of the Auger lifetime is needed, to conclusively determine the Auger coefficients for the direct Auger recombination at high majority carrier concentrations.

Wolf, M.↗

Research possibilities? No! Needs for research to make PV solar energy utilization broadly competitive

The historical progression of efficiency improvements, cost reductions, and performance improvements in modules and photovoltaic systems are described. The potential for future improvements in photovoltaic device efficiencies and cost reductions continues as device concepts, designs, processes, and automated production capabilities mature. Additional step-function improvements can be made as today's simpler devices are replaced by more sophisticated devices.

Wolf, M.↗

Comparison of various silicon sawing methods

The technology and economics of four methods of wafering silicon boules of large cross section are described. Slurry sawing using either blades or wires, and fixed abrasive sawing using the ID saw or by the FAST method, having the abrasive attached to wires which are arranged in a blade pack, are considered. The technical performance of each method is evaluated and cost/price estimates are summarized.

Wolf, M.↗

New silicon cell design concepts for 20 percent AMI efficiency

The basic design principles for obtaining high efficiency in silicon solar cells are reviewed. They critically involve very long minority carrier lifetimes, not so much to attain high collection efficiency, but primarily for increased output voltages. Minority carrier lifetime, however, is sensitive to radiation damage, and particularly in low resistivity silicon, on which the high efficiency design is based. Radiation resistant space cells will therefore have to follow differing design principles than high efficiency terrestrial cells.

Wolf, M.↗

Overview study of Space Power Technologies for the advanced energetics program

Space power technologies are reviewed to determine the state-of-the-art and to identify advanced or novel concepts which promise large increases in performance. The potential for incresed performance is judged relative to benchmarks based on technologies which have been flight tested. Space power technology concepts selected for their potentially high performance are prioritized in a list of R & D topical recommendations for the NASA program on Advanced Energetics. The technology categories studied are solar collection, nuclear power sources, energy conversion, energy storage, power transmission, and power processing. The emphasis is on electric power generation in space for satellite on board electric power, for electric propulsion, or for beamed power to spacecraft. Generic mission categories such as low Earth orbit missions and geosynchronous orbit missions are used to distinguish general requirements placed on the performance of power conversion technology. Each space power technology is judged on its own merits without reference to specific missions or power systems. Recommendations include 31 space power concepts which span the entire collection of technology categories studied and represent the critical technologies needed for higher power, lighter weight, more efficient power conversion in space.

Taussig, R.↗

Transport velocity transformation - A convenient method for performance analysis of multilayer solar cell structure

It is noted that in the case of low-level injection, space-charge quasi-neutrality, and spatially constant material parameters (including an electrostatic field), the individual layer can be treated analytically and the basic solar cell performance parameters can be evaluated from three equations. The first equation represents the transformation of the transport velocity across the layer from the other layer boundary. The second establishes the light-generated current output from the layer interface, under the influence of the transport velocities and minority-carrier density at both layer boundaries and of bulk recombination. The third equation describes the flow of these carriers across other layers. The power of the approach is considered to lie in its facility for analysis of the solar cell's performance layer by layer, giving a clear picture of the individual layer's influence on cell efficiency.

Wolf, M.↗

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

The effect of solar cell metallization pattern design on solar cell performance and the costs and performance effects of different metallization processes are discussed. Definitive design rules for the front metallization pattern for large area solar cells are presented. Chemical and physical deposition processes for metallization are described and compared. An economic evaluation of the 6 principal metallization options is presented. Instructions for preparing Format A cost data for solar cell manufacturing processes from UPPC forms for input into the SAMIC computer program are presented.

Wolf, M.↗

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

The attributes of the various metallization processes were investigated. It is shown that several metallization process sequences will lead to adequate metallization for large area, high performance solar cells at a metallization add on price in the range of $6. to 12. m squared, or 4 to $.8/W(peak), assuming 15% efficiency. Conduction layer formation by thick film silver or by tin or tin/lead solder leads to metallization add-on prices significantly above the $6. to 12/m squared range c.) The wet chemical processes of electroless and electrolytic plating for strike/barrier layer and conduction layer formation, respectively, seem to be most cost effective.

Wolf, M.↗

Metallization for large-area solar cells

In large area, low cost solar cells of any type, the contact and grid structure metallization is an important factor which has an effect on the efficiency of the solar cell and its reliability. The present investigation is concerned with aspects of solar cell efficiency. An optimized metallization design leads to minimum total power loss, which is related to a simultaneous minimization of ohmic voltage drops and of shading of the front surface of the cell by the overlaid metal. The requirements regarding the design for a low-loss metallization pattern for the front surface of large area solar cells are represented by a set of design rules listed in a table. The total shading and voltage drop on such cells can be held to about 5%. However, not every metallization process is suited for meeting the requirements of the low-cost design. The low losses can be achieved only by use of several bus lines containing a bulk conductor, such as a wire.

Wolf, M.↗

Interactions of efficiency and material requirements for terrestrial silicon solar cells

The transport velocity transformation method was used to analyze solar cell designs to determine optimum cell structures. It was found that low resistivity materials should be used up to the onset of Auger recombination; a properly designed three-layer structure permits base region approaching an ideal device in performance; and that higher resistivity front regions will need more sophisticated grid metallization structures than those used now. It was concluded that new features will provide idealized silicon cell structures yielding airmass 1 efficiencies in the 24-26.5% range, with real efficiencies near 22%.

Bowler, D. L.↗

Updating the limit efficiency of silicon solar cells

The limit efficiency of a silicon solar cell is investigated using an analytical approach. The analytical model is based on the solution of a transport equation for minority carriers derived from the Shockley equations. On the basis of the computations, a 'narrow-region' design approach is suggested for both the front and the back regions of the solar cell. The design relies on low effective surface-recombination velocities, a textured front surface, and an optical internally reflecting back surface. With this approach, the limit efficiency is near 25%, and the optimum cell is 50 to 150 microns thick.

Wolf, M.↗

Low cost processes for fabricating silicon solar cells

Solar cell fabrication processes, in particular junction formation and metallization, are evaluated in terms of cell efficiencies, process yields, module packing factors, and energy cost effectiveness. It is shown that for junction formation, the diffusion processes provide a relatively low-cost approach. The costs per unit cell area can be further reduced by increased wafer area and mechanized wafer handling. The costs for a large number of metallization processes, excluding the costs of the metal, are roughly comparable. However, their varying influence on cell performance leads to a significant spread in the allowable process costs.

Goldman, H.↗

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

Analyses of slicing processes and junction formation processes are presented. A simple method for evaluation of the relative economic merits of competing process options with respect to the cost of energy produced by the system is described. An energy consumption analysis was developed and applied to determine the energy consumption in the solar module fabrication process sequence, from the mining of the SiO2 to shipping. The analysis shows that, in current technology practice, inordinate energy use in the purification step, and large wastage of the invested energy through losses, particularly poor conversion in slicing, as well as inadequate yields throughout. The cell process energy expenditures already show a downward trend based on increased throughput rates. The large improvement, however, depends on the introduction of a more efficient purification process and of acceptable ribbon growing techniques.

Goldman, H.↗

Updating the limit efficiency of silicon solar cells

Evaluation of the limit efficiency based on the simplest, most basic mathematical method that is appropriate for the conditions imposed by the cell model is discussed. The methodology, the solar cell structure, and the selection of the material parameters used in the evaluation are described. The results are discussed including a set of design goals derived from the limit efficiency.

Wolf, M.↗

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

The energy consumed in manufacturing silicon solar cell modules was calculated for the current process, as well as for 1982 and 1986 projected processes. In addition, energy payback times for the above three sequences are shown. The module manufacturing energy was partitioned two ways. In one way, the silicon reduction, silicon purification, sheet formation, cell fabrication, and encapsulation energies were found. In addition, the facility, equipment, processing material and direct material lost-in-process energies were appropriated in junction formation processes and full module manufacturing sequences. A brief methodology accounting for the energy of silicon wafers lost-in-processing during cell manufacturing is described.

Goldman, H.↗