Search NASA⌕ Search

Engineering topics

Yan, Yanfa

Publications and source records attributed to Yan, Yanfa.

At least 199 records · Page 11

Employing Lead Thiocyanate Additive to Reduce the Hysteresis and Boost the Fill Factor of Planar Perovskite Solar Cells

Lead thiocyanate in the perovskite precursor can increase the grain size of a perovskite thin film and reduce the conductivity of the grain boundaries, leading to perovskite solar cells with reduced hysteresis and enhanced fill factor. A planar perovskite solar cell with grain boundary and interface passivation achieves a steady-state efficiency of 18.42%.

36 MATERIALS SCIENCE↗

Photovoltaic Properties of Two-Dimensional (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 Perovskite: A Combined Experimental and Density Functional Theory Study

We explore the photovoltaic-relevant properties of the two-dimensional 2D MA 2 Pb(SCN) 2 I 2 (where MA = CH 3 NH 3 + ) perovskite using a combination of materials synthesis, characterization and density-functional theory calculation. We show that the electronic properties of MA 2 Pb(SCN) 2 I 2 are significantly different from those previously reported in literature. The layered perovskite with mixed-anions exhibits an indirect bandgap of about ~2.04 eV, with a slightly larger direct bandgap of about 2.11 eV, in contrast to the previously reported bandgap of ~1.57 eV. The carriers (both electrons and holes) are also found to be confined within the 2D layers. Our results suggest that the 2D MA 2 Pb(SCN) 2 I 2 perovskite may not be among the most promising absorbers for efficient single-junction solar cell applications. However, use as an absorber for the top cell of a tandem solar cell may still be a possibility, if films are grown with the 2D layers aligned perpendicular to the substrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thin-Film Deposition and Characterization of a Sn-Deficient Perovskite Derivative Cs 2 SnI 6

In this work, we describe details of a two-step deposition approach that enables the preparation of continuous and well-structured thin films of Cs 2 SnI 6 , which is a one-half Sn-deficient 0-D perovskite derivative (i.e., the compound can also be written as CsSn 0.5 I 3 , with a structure consisting of isolated SnI 6 4- octahedra). The films were characterized using powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), UV-Vis spectroscopy, photoluminescence (PL), photoelectron spectroscopy (UPS, IPES, XPS) and Hall effect measurements. UV-Vis and PL measurements indicate that the obtained Cs 2 SnI 6 film is a semiconductor with a band gap of 1.6 eV. This band gap was further confirmed by the UPS and IPES spectra, which were well reproduced by the calculated density of states with the HSE hybrid functional. The Cs 2 SnI 6 films exhibited n-type conduction with a carrier density of 6(1) × 10 16 cm -3 and mobility of 2.9(3) cm 2 /V·s. While the computationally-derived band structure for Cs 2 SnI 6 shows significant dispersion along several directions in the Brillouin zone near the band edges, the valence band is relatively flat along the $Γ$–X direction, indicative of a more limited hole minority carrier mobility compared to analogous values for the electrons. The ionization potential (IP) and electron affinity (EA) were determined to be 6.4 and 4.8 eV, respectively. The Cs 2 SnI 6 films show some enhanced stability under ambient air, compared to methylammonium lead (II) iodide perovskite films stored under similar conditions; however, the films do decompose slowly, yielding a CsI impurity. We discuss these findings in the context of suitability of Cs 2 SnI 6 for photovoltaic and related optoelectronic applications.

36 MATERIALS SCIENCE↗

Viability of Lead-Free Perovskites with Mixed Chalcogen and Halogen Anions for Photovoltaic Applications

We assess the viability for photovoltaic applications of proposed Pb-free perovskites with mixed chalcogen and halogen anions, AB(Ch,X) 3 (A = Cs or Ba; B = Sb or Bi; Ch = chalcogen; X = halogen), by examining critical issues such as the structural, electronic/optical properties, and stability through the combination of density-functional theory calculations and solid state reactions. The calculations show that these quaternary Pb-free perovskites are thermodynamically unstable--they are prone to decompose into ternary and/or binary secondary phases or form phases with nonperovskite structures. Solid-state synthesis efforts confirm the theoretically predicted difficulty for preparing these compounds; all attempted reactions do not form the desired perovskite phases with mixed chalcogen and halogen anions under conditions examined. Instead, they form separate binary and ternary compounds. Despite earlier predictions of promising characteristics for these prospective perovskites for photovoltaics, our results suggest that, due to their instability, the Pb-free perovskites with mixed chalcogen and halogen anions may be challenging to form under equilibrium synthetic conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Alloying and Defect Control within Chalcogenide Perovskites for Optimized Photovoltaic Application

Through density functional theory calculations, we show that the alloy perovskite system BaZr 1-x Ti x S 3 (x < 0.25) is a promising candidate for producing high power conversion efficiency (PCE) solar cells with ultrathin absorber layers. To maximize the minority carrier lifetime, which is important for achieving high PCE, the defect calculations show that BaZr 1-x Ti x S 3 films should be synthesized under moderate (i.e., near stoichiometric) growth conditions to minimize the formation of deep-level defects. The perovskite BaZrS 3 is also found to exhibit ambipolar self-doping properties, indicating the ability to form homo p–n junctions. However, our theoretical calculations and experimental solid-state reaction efforts indicate that the doped perovskite BaZr 1-x Ti x S 3 (x > 0) may not be stable under thermal equilibrium growth conditions. Calculations of decomposition energies suggest that introducing compressive strain may be a plausible approach to stabilize BaZr 1-x Ti x S 3 thin films.

14 SOLAR ENERGY↗

High Resolution Dopant Profiles Revealed by Atom Probe Tomography and STEM-EBIC for CdTe Based Solar Cells

Segregated elements and their diffusion profiles within grain boundaries and interfaces resulting from post deposition heat treatments are revealed using atom probe tomography (APT), scanning transmission electron microscopy (STEM), and electron beam induced current (EBIC) techniques. The results demonstrate how these techniques complement each other to provide conclusive evidence for locations of space charge regions and mechanisms that create them at the nanoscale. Most importantly, a Cl dopant profile that extends ~5 nm into CdTe grains interfacing the CdS is shown using APT and STEM synergy, which has been shown to push the pn-junction into the CdTe layer indicative of a homojunction (revealed by STEM EBIC). In addition, Cu and Cl concentrations within grain boundaries within several nms and µms from the CdS/CdTe interface are compared, Na segregation of <0.1% is detected, and S variations of ~1–3% are witnessed between CdTe grains close to the CdS/CdTe interface. The segregation and diffusion of these elements directly impacts on the material properties, such as band gap energy and n/p type properties. Optimization of the interfacial and grain boundary doping will lead to higher efficiency solar cells.

36 MATERIALS SCIENCE↗

Surface stability and the selection rules of substrate orientation for optimal growth of epitaxial II-VI semiconductors

The surface structures of ionic zinc-blende CdTe (001), (110), (111), and (211) surfaces are systematically studied by first-principles density functional calculations. Based on the surface structures and surface energies, we identify the detrimental twinning appearing in molecular beam epitaxy (MBE) growth of II-VI compounds as the (111) lamellar twin boundaries. To avoid the appearance of twinning in MBE growth, we propose the following selection rules for choosing optimal substrate orientations: (1) the surface should be nonpolar so that there is no large surface reconstructions that could act as a nucleation center and promote the formation of twins; (2) the surface structure should have low symmetry so that there are no multiple equivalent directions for growth. These straightforward rules, in consistent with experimental observations, provide guidelines for selecting proper substrates for high-quality MBE growth of II-VI compounds.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Current enhancement of CdTe-based solar cells

We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO 2 /SnO 2 :F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl 2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSe x Te 1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (V OC ). To overcome the V OC loss and maintain a high short-circuit current (J SC ), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a V OC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a V OC of 831 mV, a J SC of 26.3 mA/cm 2 , and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.

14 SOLAR ENERGY↗

Application of copper thiocyanate for high open‐circuit voltages of CdTe solar cells

Abstract Copper thiocyanate (CuSCN) has proven to be a low‐cost, efficient hole‐transporting material for the emerging organic–inorganic perovskite solar cells. Herein, we report that CuSCN can also be applied to CdTe thin‐film solar cells to achieve high open‐circuit voltages ( V OC s). By optimizing the thickness of the thermally evaporated CuSCN films, CdTe cells fabricated by close space sublimation in the superstrate configuration have achieved V OC s as high as 872 mV, which is about 20–25 mV higher than the highest V OC for the reference cells using the standard Cu/Au back contacts. CuSCN is a wide bandgap p ‐type conductor with a conduction band higher than that of CdTe, leading to a conduction band offset that reflects electrons in CdTe, partially explaining the improved V OC s. However, due to the low conductivity of CuSCN, CdTe cells using CuSCN/Au back contacts exhibited slightly lower fill factors than the cells using Cu/Au back contacts. With optimized CdS:O window layers, the power conversion efficiency of the best CdTe cell, using CuSCN/Au back contact, is 14.7%: slightly lower than that of the best cell (15.2%) using Cu/Au back contact. Copyright © 2015 John Wiley & Sons, Ltd.

Paudel, Naba R.↗

Recombination by grain-boundary type in CdTe

We conducted cathodoluminescence (CL) spectrum imaging and electron backscatter diffraction on the same microscopic areas of CdTe thin films to correlate grain-boundary (GB) recombination by GB “type.” We examined misorientation-based GB types, including coincident site lattice (CSL) Σ = 3, other-CSL (Σ = 5–49), and general GBs (Σ > 49), which make up ∼47%–48%, ∼6%–8%, and ∼44%–47%, respectively, of the GB length at the film back surfaces. Statistically averaged CL total intensities were calculated for each GB type from sample sizes of ≥97 GBs per type and were compared to the average grain-interior CL intensity. We find that only ∼16%–18% of Σ = 3 GBs are active non-radiative recombination centers. In contrast, all other-CSL and general GBs are observed to be strong non-radiative centers and, interestingly, these GB types have about the same CL intensity. Both as-deposited and CdCl{sub 2}-treated films were studied. The CdCl{sub 2} treatment reduces non-radiative recombination at both other-CSL and general GBs, but GBs are still recombination centers after the CdCl{sub 2} treatment.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗