Search NASA⌕ Search

Engineering topics

Yan, Yanfa

Publications and source records attributed to Yan, Yanfa.

At least 181 records · Page 10

Distant-Atom Mutation for Better Earth-Abundant Light Absorbers: A Case Study of Cu 2 BaSnSe 4

Thin-film Cu(In,Ga)Se 2 and CdTe solar cells have demonstrated high power conversion efficiencies, but they cannot provide a sustainable clean energy pathway because of the scarcity of Te and In. In this paper, we propose a distant-atom concept to mutate In by a group II element (Ba) and a group IV element (Sn) that are at rather different locations on the periodic table. Because of the very different electronic properties between the cations, the resultant earth-abundant orthorhombic Cu 2 BaSnSe 4 absorber does not have the detrimental cation–cation disorder issue seen in the earth-abundant kesterite Cu 2 ZnSnSe 4 absorber. We anticipate that Cu 2 BaSnSe 4 solar cells should not have large open-circuit voltage deficits as seen in CuZnSnSe 4 solar cells. Density functional theory calculation of the electronic and defect properties of Cu 2 BaSnSe 4 confirms these expectations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanometer-Scale Electrical Potential Profiling Across Perovskite Solar Cells

We used Kelvin probe force microscopy to study the potential distribution on cross-section of perovskite solar cells with different types of electron-transporting layers (ETLs). Our results explain the low open-circuit voltage and fill factor in ETL-free cells, and support the fact that intrinsic SnO2 as an alternative ETL material can make high-performance devices. Furthermore, the potential-profiling results indicate a reduction in junction-interface recombination by the optimized SnO2 layer and adding a fullerene layer, which is consistent with the improved device performance and current-voltage hysteresis.

14 SOLAR ENERGY↗

Determination of the Electrical Junction in Cu(In, Ga)Se2 and Cu2ZnSnSe4 Solar Cells with 20-nm Spatial Resolution

We located the electrical junction (EJ) of Cu(In, Ga)Se2 (CIGS) and Cu2ZnSnSe4 (CZTS) solar cells with ~20-nm accuracy using a scanning capacitance spectroscopy (SCS) technique. A procedure was developed to prepare the cross-sectional samples and grow critical high-quality insulating layers for the SCS measurement. We found that CIGS has a buried homojunction with the EJ located at ~40 nm inside the CIGS/CdS interface. An n-type CIGS was probed in the region 10-30 nm away from the interface. By contrast, the CZTS/CdS cells have a heterointerface junction with a shallower EJ (~20 nm) than CIGS. The EJ is ~20 nm from the CZTS/CdS interface, which is consistent with asymmetrical carrier concentrations of the p-CZTS and n-CdS in a heterojunction cell. The unambiguous determination of the junction locations helped explain the large open circuit voltage difference between the state-of-the-art devices of CIGS and CZTS.

14 SOLAR ENERGY↗

Column-by-column observation of dislocation motion in CdTe: Dynamic scanning transmission electron microscopy

The dynamics of partial dislocations in CdTe have been observed at the atomic scale using aberration-corrected scanning transmission electron microscopy (STEM), allowing the mobility of different dislocations to be directly compared: Cd-core Shockley partial dislocations are more mobile than Te-core partials, and dislocation cores with unpaired columns have higher mobility than those without unpaired columns. The dynamic imaging also provides insight into the process by which the dislocations glide. Dislocations with dangling bonds on unpaired columns are found to be more mobile because the dangling bonds mediate the bond exchanges required for the dislocations to move. Furthermore, a screw dislocation has been resolved to dissociate into a Shockley partial-dislocation pair along two different directions, revealing a way for the screw dislocation to glide in the material. The results show that dynamic STEM imaging has the potential to uncover the details of dislocation motion not easily accessible by other means. This research was sponsored by the U.S. DOE, Office of Energy Efficiency and Renewable Energy, Foundational Program to Advance Cell Efficiency (F-PACE, DE-FOA-0000492), (CL, YLW, NP, YFY, SJP), the Office of DOE-BES, Materials Science and Engineering Division (ARL), DOE Grant No. DE-FG02-09ER46554 (YYZ, STP), and a user project supported by ORNL's Center for Nanophase Materials Sciences (CNMS), which is also sponsored by DOE-BES. Supercomputer time was provided by the National Center for Supercomputing Applications which is supported by the DOE Office of Science under Contract No. DE-AC02-05CH11231, and the Extreme Science and Engineering Discovery Environment (XSEDE), which is supported by National Science Foundation Grant No. ACI-1053575. Chen Li [No. 656378] and Timothy Pennycook [No.655760] are currently funded by the European Union's Marie Sklodowska-Curie Grants.

36 MATERIALS SCIENCE↗

Thermally evaporated methylammonium tin triiodide thin films for lead-free perovskite solar cell fabrication

Here, we report on the synthesis of methylammonium tin triiodide (MASnI 3 ) thin films at room temperature by a hybrid thermal evaporation method and their application in fabricating lead (Pb)-free perovskite solar cells. The as-deposited MASnI 3 thin films exhibit smooth surfaces, uniform coverage across the entire substrate, and strong crystallographic preferred orientation along the < 100 > direction. By incorporating this film with an inverted planar device architecture, our Pb-free perovskite solar cells are able to achieve an open-circuit voltage ( V oc ) up to 494 mV. The relatively high V oc is mainly ascribed to the excellent surface coverage, the compact morphology, the good stoichiometry control of the MASnI 3 thin films, and the effective passivation of the electron-blocking and hole-blocking layers. Finally, our results demonstrate the potential capability of the hybrid evaporation method to prepare high-quality Pb-free MASnI 3 perovskite thin films which can be used to fabricate efficient Pb-free perovskite solar cells.

14 SOLAR ENERGY↗

Fabrication of efficient low-bandgap perovskite solar cells by combining formamidinium tin iodide with methylammonium lead iodide

Mixed tin (Sn)-lead (Pb) perovskites with high Sn content exhibit low bandgaps suitable for fabricating the bottom cell of perovskite-based tandem solar cells. In this work, we report on the fabrication of efficient mixed Sn-Pb perovskite solar cells using precursors combining formamidinium tin iodide (FASnI 3 ) and methylammonium lead iodide (MAPbI 3 ). The best-performing cell fabricated using a (FASnI 3 ) 0.6 (MAPbI 3 ) 0.4 absorber with an absorption edge of ~1.2 eV achieved a power conversion efficiency (PCE) of 15.08 (15.00)% with an open-circuit voltage of 0.795 (0.799) V, a short-circuit current density of 26.86(26.82) mA/cm 2 , and a fill factor of 70.6(70.0)% when measured under forward (reverse) voltage scan. In conclusion, the average PCE of 50 cells we have fabricated is 14.39 ± 0.33%, indicating good reproducibility.

14 SOLAR ENERGY↗

Crystal Structure of AgBi 2 I 7 Thin Films

Synthesis of cubic-phase AgBi 2 I 7 iodobismuthate thin films and fabrication of air-stable Pb-free solar cells using the AgBi 2 I 7 absorber have recently been reported. Based on X-ray diffraction (XRD) analysis and nominal composition, it was suggested that the synthesized films have a cubic ThZr 2 H 7 crystal structure with AgBi 2 I 7 stoichiometry. Through careful examination of the proposed structure and computational evaluation of the phase stability and bandgap, we find that the reported “AgBi 2 I 7 ” films cannot be forming with the ThZr 2 H 7 -type structure, but rather more likely adopt an Ag-deficient AgBiI 4 type. Both the experimental X-ray diffraction pattern and band gap can be better explained by the AgBiI 4 structure. Additionally, the proposed AgBiI 4 structure, with octahedral bismuth coordination, removes unphysically short Bi–I bonding within the BiI8 hexahedra of the ThZr 2 I 7 model. Our results provide critical insights for assessing the photovoltaic properties of AgBi 2 I 7 iodobismuthate materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Defect properties of the two-dimensional (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 perovskite: a density-functional theory study

Recently, solar cells based on 2D (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 perovskite have realized a power conversion efficiency of 3.23%. In this work, we study the defect properties of (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 through density-functional theory calculations. It is found that the lower crystal structure dimensionality of (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 makes the valence band maximum lower and the conduction band minimum higher as compared to its 3D CH 3 NH 3 PbI 3 perovskite counterpart, resulting in relatively deeper defect transition levels. Our calculated defect formation energies suggest that if the 2D (CH 3 NH 3 ) 2 Pb(SCN) 2 I 2 perovskite absorbers are synthesized under Pb-poor and I-rich conditions, the dominant defects should be Pb vacancies, which create shallow levels. Finally, the resultant perovskite films are expected to exhibit p-type conductivity with a relatively long carrier lifetime.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lead-free inverted planar formamidinium tin triiodide perovskite solar cells achieving power conversion efficiencies up to 6.22%

Efficient lead (Pb)-free inverted planar formamidinium tin triiodide (FASnI 3 ) perovskite solar cells (PVSCs) are demonstrated. Our FASnI 3 PVSCs achieved average power conversion efficiencies (PCEs) of 5.41% ± 0.46% and a maximum PCE of 6.22% under forward voltage scan. Here, the PVSCs exhibit small photocurrent–voltage hysteresis and high reproducibility. The champion cell shows a steady-state efficiency of ≈6.00% for over 100 s.

14 SOLAR ENERGY↗

Cooperative tin oxide fullerene electron selective layers for high-performance planar perovskite solar cells

Both tin oxide (SnO 2 ) and fullerenes have been reported as electron selective layers (ESLs) for producing efficient lead halide perovskite solar cells. Here, we report that SnO 2 and fullerenes can work cooperatively to further boost the performance of perovskite solar cells. We find that fullerenes can be redissolved during perovskite deposition, allowing ultra-thin fullerenes to be retained at the interface and some dissolved fullerenes infiltrate into perovskite grain boundaries. The SnO 2 layer blocks holes effectively; whereas, the fullerenes promote electron transfer and passivate both the SnO 2 /perovskite interface and perovskite grain boundaries. With careful device optimization, the best-performing planar perovskite solar cell using a fullerene passivated SnO 2 ESL has achieved a steady-state efficiency of 17.75% and a power conversion efficiency of 19.12% with an open circuit voltage of 1.12 V, a short-circuit current density of 22.61 mA cm -2 , and a fill factor of 75.8% when measured under reverse voltage scanning. In conclusion, we find that the partial dissolving of fullerenes during perovskite deposition is the key for fabricating high-performance perovskite solar cells based on metal oxide/fullerene ESLs.

14 SOLAR ENERGY↗

Locating the electrical junctions in Cu(In,Ga)Se 2 and Cu 2 ZnSnSe 4 solar cells by scanning capacitance spectroscopy

Here, we determined the electrical junction (EJ) locations in Cu(In,Ga)Se 2 (CIGS) and Cu 2 ZnSnSe 4 (CZTS) solar cells with ~20-nm accuracy by developing scanning capacitance spectroscopy (SCS) applicable to the thin-film devices. Cross-sectional sample preparation for the SCS measurement was developed by high-energy ion milling at room temperature for polishing the cross section to make it flat, followed by low-energy ion milling at liquid nitrogen temperature for removing the damaged layer and subsequent annealing for growing a native oxide layer. The SCS shows distinct p-type, transitional, and n-type spectra across the devices, and the spectral features change rapidly with location in the depletion region, which results in determining the EJ with ~20-nm resolution. We found an n-type CIGS in the region next to the CIGS/CdS interface; thus, the cell is a homojunction. The EJ is ~40 nm from the interface on the CIGS side. In contrast, such an n-type CZTS was not found in the CZTS/CdS cells. The EJ is ~20 nm from the CZTS/CdS interface, which is consistent with asymmetrical carrier concentrations of the p-CZTS and n-CdS in a heterojunction cell. Our results of unambiguously determination of the junction locations contribute significantly to understanding the large open-circuit voltage difference between CIGS and CZTS.

14 SOLAR ENERGY↗

Thermodynamic Stability and Defect Chemistry of Bismuth-Based Lead-Free Double Perovskite Cs 2 AgBiBr 6

Bismuth or antimony based lead-free double perovskites represented by Cs 2 AgBiBr 6 have recently been considered promising alternatives to the emerging lead-based perovskites for solar cell applications. These new perovskites belong to the Fm -3 m space group and consist of two types of octahedra alternating in a rock-salt face-centered cubic structure. We show, by density functional theory calculation, that the stable chemical potential region for pure Cs 2 AgBiBr 6 is narrow. Silver vacancy is a shallow accepter and can easily form, leading to intrinsic p -type conductivity. Bi vacancy and Ag Bi antisite are deep acceptors and should be the dominant defects under the Br-rich growth conditions. Our results suggest that the growth of Cs 2 AgBiBr 6 under Br-poor/Bi-rich conditions is preferred for suppressing the formation of the deep defects, which is beneficial for maximizing the photovoltaic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural and compositional dependence of the CdTexSe 1-x alloy layer photoactivity in CdTe-based solar cells

The published external quantum efficiency data of the world-record CdTe solar cell suggests that the device uses bandgap engineering, most likely with a CdTe x Se 1₋x alloy layer to increase the short-circuit current and overall device efficiency. Here atom probe tomography, transmission electron microscopy and electron beam-induced current are used to clarify the dependence of Se content on the photoactive properties of CdTe x Se 1₋x alloy layers in bandgap-graded CdTe solar cells. Four solar cells were prepared with 50, 100, 200 and 400 nm-thick CdSe layers to reveal the formation, growth, composition, structure and photoactivity of the CdTe x Se 1₋x alloy with respect to the degree of Se diffusion. Finally, the results show that the CdTe x Se 1₋x layer photoactivity is highly dependent on the crystalline structure of the alloy (zincblende versus wurtzite), which is also dependent on the Se and Te concentrations.

14 SOLAR ENERGY↗

Improved Performance of Electroplated CZTS Thin-Film Solar Cells with Bifacial Configuration

Annealing in S vapor greatly improves the performance of electroplated Cu2ZnSnS4 (CZTS) solar cells based on the bifacial configuration of Al-doped ZnO (AZO, front contact)/ZnO/CdS/CZTS/indium tin oxide (ITO, back contact), as compared to H2S annealing in our previous works. S-vapor annealing does not cause severe damage to the conductivity of the ITO back contact. The highest device efficiency of 5.8% was reached under 1 sun illumination from the AZO side. The well-preformed devices based on the ITO back contact demonstrate smaller series resistances and better fill factors, as compared to our substrate-type devices using Mo back contacts. An interfacial reaction at the ITO back contact has been revealed in experiments, which contributes to the formation of SnO2-enriched interfacial layer and diffusion of In from ITO into CZTS through the Sn sites. Incorporation of In does not significantly change the optical and structural properties or the grain size of CZTS absorbers.

14 SOLAR ENERGY↗

Effects of oxygen partial pressure, deposition temperature, and annealing on the optical response of CdS:O thin films as studied by spectroscopic ellipsometry

Ex-situ spectroscopic ellipsometry measurements are made on radio frequency magnetron sputtered oxygenated cadmium sulfide (CdS:O) thin films. Films are deposited onto glass substrates at room temperature and at 270 °C with varying oxygen to total gas flow ratios in the sputtering ambient. Ellipsometric spectra from 0.74 to 5.89 eV are collected before and after annealing at 607 °C to simulate the thermal processes during close-space sublimation of overlying cadmium telluride in that solar cell configuration. Complex dielectric function (ε = ε{sub 1} + iε{sub 2}) spectra are extracted for films as a function of oxygen gas flow ratio, deposition temperature, and post-deposition annealing using a parametric model accounting for critical point transitions and an Urbach tail for sub-band gap absorption. The results suggest an inverse relationship between degree of crystallinity and oxygen gas flow ratio, whereas annealing is shown to increase crystallinity in all samples. Direct band gap energies are determined from the parametric modeling of ε and linear extrapolations of the square of the absorption coefficient. As-deposited samples feature a range of band gap energies whereas annealing is shown to result in gap energies ranging only from 2.40 to 2.45 eV, which is close to typical band gaps for pure cadmium sulfide.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗