Search NASA⌕ Search

Engineering topics

Yan, Yanfa

Publications and source records attributed to Yan, Yanfa.

At least 163 records · Page 9

Electronic band structures and excitonic properties of delafossites: A $GW$-BSE study

We report the band structures and excitonic properties of delafossites CuMO 2 (M=Al, Ga, In, Sc, Y, Cr) calculated using the state-of-the-art GW-BSE approach. We evaluate different levels of self-consistency of the GW approximations, namely G 0 W 0 , GW 0 , GW, and QSGW, on the band structures and find that GW0, in general, predicts the band gaps in better agreement with experiments considering the electron-hole effect. For CuCrO 2 , the HSE wave function is used as the starting point for the perturbative GW0 calculations, since it corrects the band orders wrongly predicted by PBE. The discrepancy about the valence band characters of CuCrO 2 is classified based on both HSE and QSGW calculations. The PBE wave functions, already good, are used for other delafossites. All the delafossites are shown to be indirect band gap semiconductors with large exciton binding energies, varying from 0.24 to 0.44 eV, in consistent with experimental findings. The excitation mechanisms are explained by examining the exciton amplitude projections on the band structures. Discrepancies compared with experiments are also addressed. The lowest and strongest exciton, mainly contributed from either Cu 3d → Cu 3p (Al, Ga, In) or Cu 3d → M 3d (M = Sc, Y, Cr) transitions, is always located at the L point of the rhombohedral Brillouin zone.

74 ATOMIC AND MOLECULAR PHYSICS↗

Chemical Origin of the Stability Difference between Cu(I)- and Ag(I)-Based Halide Double Perovskites

Recently, Cu(I)- and Ag(I)-based halide double perovskites have been proposed as promising candidates for overcoming the toxicity and instability issues inherent within the emerging Pb-based halide perovskite absorbers. However, up to date, only Ag(I)-based halide double perovskites have been experimentally synthesized; there are no reports on successful synthesis of Cu(I)-based analogues. In this study, we show that, owing to the much higher energy level for the Cu 3d 10 orbital than for the Ag 4d 10 orbital, Cu(I) atoms energetically favor 4-fold coordination, forming [CuX 4 ] tetrahedra (X = halogen), but not 6-fold coordination as required for [CuX 6 ] octahedra. In contrast, Ag(I) atoms can have both 6- and 4-fold coordination’s. Our density functional theory calculations reveal that the synthesis of Cu(I) halide double perovskites may instead lead to products containing [CuX 4 ] tetrahedra, as confirmed by our material synthesis efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical Origin of the Stability Difference between Copper(I)- and Silver(I)-Based Halide Double Perovskites

Recently, Cu I - and Ag I -based halide double perovskites have been proposed as promising candidates for overcoming the toxicity and instability issues inherent within the emerging Pb-based halide perovskite absorbers. However, up to date, only Ag I -based halide double perovskites have been experimentally synthesized; there are no reports on successful synthesis of Cu I -based analogues. Here we show that, owing to the much higher energy level for the Cu 3d 10 orbitals than for the Ag 4d 10 orbitals, CuI atoms energetically favor 4-fold coordination, forming [CuX 4 ] tetrahedra (X=halogen), but not 6-fold coordination as required for [CuX 6 ] octahedra. In contrast, Ag I atoms can have both 6- and 4-fold coordinations. In this work, our density functional theory calculations reveal that the synthesis of Cu I halide double perovskites may instead lead to non-perovskites containing [CuX 4 ] tetrahedra, as confirmed by our material synthesis efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical response of mixed methylammonium lead iodide and formamidinium tin iodide perovskite thin films

Here, mixed tin (Sn) and lead (Pb) based perovskite thin films have been prepared by solution processing combining methylammonium lead iodide (MAPbI 3 ) and formamidinium tin iodide (FASnI 3 ) precursors. Optical response in the form of complex dielectric function (ε = ε 1 + iε 2 ) spectra and absorption coefficient (α) spectra of (FASnI 3 ) 1-x (MAPbI 3 ) x based perovskite films have been extracted over a spectral range 0.74 to 5.89 eV using spectroscopic ellipsometry. Absorption band edge energy changes as a function of composition for films including FASnI 3 , MAPbI 3 , and mixed x = 0.20, 0.35, 0.40, and 0.6 (FASnI 3 ) 1-x (MAPbI 3 ) x perovskites. (FASnI 3 ) 0.60 (MAPbI 3 ) 0.4 is found to have the minimum absorption band edge energy near ~1.2 eV.

36 MATERIALS SCIENCE↗

Understanding individual defects in CdTe thin-film solar cells via STEM: From atomic structure to electrical activity

Here in this paper we review a systematic study of the structure-property correlations of a series of defects in CdTe solar cells. A variety of experimental methods, including aberration-corrected scanning transmission electron microscopy, electron energy loss spectroscopy, energy dispersive X-ray spectroscopy, and electron-beam-induced current have been combined with density-functional theory. The research traces the connections between the structures and electrical activities of individual defects including intra-grain partial dislocations, grain boundaries and the CdTe/CdS interface. The interpretations of the physical origin underlying the structure-property correlation provide insights that should further the development of future CdTe solar cells.

14 SOLAR ENERGY↗

Parity-Forbidden Transitions and Their Impact on the Optical Absorption Properties of Lead-Free Metal Halide Perovskites and Double Perovskites

Using density functional theory calculations, we analyze the optical absorption properties of lead (Pb)-free metal halide perovskites (AB2+X3) and double perovskites (A2B+B3+X6) (A = Cs or monovalent organic ion, B2+ = non-Pb divalent metal, B+ = monovalent metal, B3+ = trivalent metal, X = halogen). We show that if B2+ is not Sn or Ge, Pb-free metal halide perovskites exhibit poor optical absorptions because of their indirect band gap nature. Among the nine possible types of Pb-free metal halide double perovskites, six have direct band gaps. Of these six types, four show inversion symmetry-induced parity-forbidden or weak transitions between band edges, making them not ideal for thin-film solar cell applications. Only one type of Pb-free double perovskite shows optical absorption and electronic properties suitable for solar cell applications, namely, those with B+ = In, Tl and B3+ = Sb, Bi. Our results provide important insights for designing new metal halide perovskites and double perovskites for optoelectronic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Bandgap Engineering of Lead‐Free Double Perovskite Cs 2 AgBiBr 6 through Trivalent Metal Alloying

Abstract The double perovskite family, A 2 M I M III X 6 , is a promising route to overcome the lead toxicity issue confronting the current photovoltaic (PV) standout, CH 3 NH 3 PbI 3 . Given the generally large indirect band gap within most known double perovskites, band‐gap engineering provides an important approach for targeting outstanding PV performance within this family. Using Cs 2 AgBiBr 6 as host, band‐gap engineering through alloying of In III /Sb III has been demonstrated in the current work. Cs 2 Ag(Bi 1− x M x )Br 6 (M=In, Sb) accommodates up to 75 % In III with increased band gap, and up to 37.5 % Sb III with reduced band gap; that is, enabling ca. 0.41 eV band gap modulation through introduction of the two metals, with smallest value of 1.86 eV for Cs 2 Ag(Bi 0.625 Sb 0.375 )Br 6 . Band structure calculations indicate that opposite band gap shift directions associated with Sb/In substitution arise from different atomic configurations for these atoms. Associated photoluminescence and environmental stability of the three‐metal systems are also assessed.

Du, Ke‐zhao↗

Understanding and Eliminating Hysteresis for Highly Efficient Planar Perovskite Solar Cells

Through detailed device characterization using cross-sectional Kelvin probe force microscopy (KPFM) and trap density of states measurements, we identify that the J-V hysteresis seen in planar organic-inorganic hybrid perovskite solar cells (PVSCs) using SnO 2 electron selective layers (ESLs) synthesized by low-temperature plasma-enhanced atomic-layer deposition (PEALD) method is mainly caused by the imbalanced charge transportation between the ESL/perovskite and the hole selective layer/perovskite interfaces. We find that this charge transportation imbalance is originated from the poor electrical conductivity of the low-temperature PEALD SnO 2 ESL. We further discover that a facile low-temperature thermal annealing of SnO 2 ESLs can effectively improve the electrical mobility of low-temperature PEALD SnO 2 ESLs and consequently significantly reduce or even eliminate the J-V hysteresis. With the reduction of J-V hysteresis and optimization of deposition process, planar PVSCs with stabilized output powers up to 20.3% are achieved. Here, the results of this study provide insights for further enhancing the efficiency of planar PVSCs.

14 SOLAR ENERGY↗

Synergistic effects of lead thiocyanate additive and solvent annealing on the performance of wide-bandgap perovskite solar cells

Here, we show that the cooperation of lead thiocyanate additive and a solvent annealing process can effectively increase the grain size of mixed-cation lead mixed-halide perovskite thin films while avoiding excess lead iodide formation. As a result, the average grain size of the wide-bandgap mixed-cation lead perovskite thin films increases from 66 ± 24 to 1036 ± 111 nm, and the mean carrier lifetime shows a more than 3-fold increase, from 330 ns to over 1000 ns. Consequently, the average open-circuit voltage of wide-bandgap perovskite solar cells increases by 80 (70) mV, and the average power conversion efficiency (PCE) increases from 13.44 ± 0.48 (11.75 ± 0.34) to 17.68 ± 0.36 (15.58 ± 0.55)% when measured under reverse (forward) voltage scans. The best-performing wide-bandgap perovskite solar cell, with a bandgap of 1.75 eV, achieves a stabilized PCE of 17.18%.

14 SOLAR ENERGY↗

Intrinsic Instability of Cs 2 In(I)M(III)X 6 (M = Bi, Sb; X = Halogen) Double Perovskites: A Combined Density Functional Theory and Experimental Study

Recently, there has been substantial interest in developing double-B-cation halide perovskites, which hold the potential to overcome the toxicity and instability issues inherent within emerging lead halide-based solar absorber materials. Among all double perovskites investigated, In(I)-based Cs2InBiCl6 and Cs2InSbCl6 have been proposed as promising thin-film photovoltaic absorber candidates, with computational examination predicting suitable materials properties, including direct bandgap and small effective masses for both electrons and holes. In this study, we report the intrinsic instability of Cs2In(I)M(III)X6 (M = Bi, Sb; X = halogen) double perovskites by a combination of density functional theory and experimental study. Our results suggest that the In(I)-based double perovskites are unstable against oxidation into In(III)-based compounds. Further, the results show the need to consider reduction–oxidation (redox) chemistry when predicting stability of new prospective electronic materials, especially when less common oxidation states are involved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Perovskite ink with wide processing window for scalable high-efficiency solar cells

Perovskite solar cells have made tremendous progress using laboratory-scale spin-coating methods in the past few years owing to advances in controls of perovskite film deposition. However, devices made via scalable methods are still lagging behind state-of-the-art spin-coated devices because of the complicated nature of perovskite crystallization from a precursor state. Here we demonstrate a chlorine-containing methylammonium lead iodide precursor formulation along with solvent tuning to enable a wide precursor-processing window (up to ~8 min) and a rapid grain growth rate (as short as ~1 min). Coupled with antisolvent extraction, this precursor ink delivers high-quality perovskite films with large-scale uniformity. The ink can be used by both spin-coating and blade-coating methods with indistinguishable film morphology and device performance. Using a blade-coated absorber, devices with 0.12-cm 2 and 1.2-cm 2 areas yield average efficiencies of 18.55% and 17.33%, respectively. As a result, we further demonstrate a 12.6-cm 2 four-cell module (88% geometric fill factor) with 13.3% stabilized active-area efficiency output.

14 SOLAR ENERGY↗

Low-bandgap mixed tin–lead iodide perovskite absorbers with long carrier lifetimes for all-perovskite tandem solar cells

Tandem solar cells using only metal-halide perovskite sub-cells are an attractive choice for next-generation solar cells. However, the progress in developing efficient all-perovskite tandem solar cells has been hindered by the lack of high-performance low-bandgap perovskite solar cells. Here in this paper, we report efficient mixed tin-lead iodide low-bandgap (~1.25 eV) perovskite solar cells with open-circuit voltages up to 0.85 V and over 70% external quantum efficiencies in the infrared wavelength range of 700-900 nm, delivering a short-circuit current density of over 29 mA cm -2 and demonstrating suitability for bottom-cell applications in all-perovskite tandem solar cells. Our low-bandgap perovskite solar cells achieve a maximum power conversion efficiency of 17.6% and a certified efficiency of 17.01% with a negligible current-voltage hysteresis. Finally, when mechanically stacked with a ~1.58 eV bandgap perovskite top cell, our best all-perovskite 4-terminal tandem solar cell shows a steady-state efficiency of 21.0%.

14 SOLAR ENERGY↗

Employing overlayers to improve the performance of Cu 2 BaSnS 4 thin film based photoelectrochemical water reduction devices

Earth-abundant copper-barium-thiostannate Cu 2 BaSnS 4 (CBTS)-based thin films have recently been reported to exhibit the optoelectronic and defect properties suitable as absorbers for photoelectrochemical (PEC) water splitting and the top cell of tandem photovoltaic solar cells. However, the photocurrents of CBTS-based PEC devices are still much lower than the theoretical value, partially due to ineffective charge collection at CBTS/water interface and instability of CBTS in electrolytes. Here, we report on overcoming these issues by employing overlayer engineering. We find that CdS/ZnO/TiO 2 overlayers can significant-ly improve the PEC performance, achieving saturated cathodic photocurrents up to 7.8 mA cm -2 at the potential of -0.10 V versus reversible hydrogen electrode (RHE) in a neutral electrolyte solution, which is much higher than the best bare CBTS film attaining a photocurrent of 4.8 mA cm -2 at the potential of -0.2 V versus RHE. Finally, our results suggest a viable approach for improving the performance of CBTS-based PEC cells.

08 HYDROGEN↗

A layered Na 1-x Ni y Fe 1-y O 2 double oxide oxygen evolution reaction electrocatalyst for highly efficient water-splitting

Transition metal Ni- and Co-based oxides are potential candidates to replace expensive and scarce noble metal-based oxygen evolution reaction (OER) catalysts such as IrO 2 and RuO 2 , which are required for efficient hydrogen production from solar water splitting and rechargeable energy storage technologies. So far, layered NiFe double hydroxide represents the best OER activity among all Ni- and Co-based oxides. Here, we report new layered Na 1-x Ni y Fe 1-y O 2 double oxide OER catalysts exhibiting activity and stability surpassing those of noble metal OER catalysts including IrO 2 and RuO 2 , and a layered NiFe double hydroxide OER catalyst. The superior catalytic properties can be ascribed to the layered structure as well as the enhanced covalency of Ni and Fe. Powered by a lead halide perovskite solar cell with a power conversion efficiency of 14.69%, a two-electrode solar water-splitting device combining a Na 0.08 Ni 0.9 Fe 0.1 O 2 OER catalyst with a NiP hydrogen evolution reaction catalyst delivers a solar-to-hydrogen conversion efficiency of 11.22%. Our design and fabrication strategies offer insights for developing highly active electrocatalysts for water splitting and metal–air batteries.

Weng, Baicheng↗

Searching for promising new perovskite-based photovoltaic absorbers: the importance of electronic dimensionality

Searching for promising nontoxic and air-stable perovskite absorbers for solar cell applications has drawn extensive attention. Here, we show that a promising perovskite absorber should exhibit a high electronic dimensionality. Semiconductors that exhibit a high structural dimensionality, but a low electronic dimensionality have less promise as an absorber, because of barriers to isotropic current flow, enhanced electron/hole effective masses and fundamentally deeper defect states (more effective at causing recombination). Our concept accounts for the device performance of the perovskite-based solar cells reported in literature so far.

Xiao, Zewen↗

Bandgap Engineering of Barium Bismuth Niobate Double Perovskite for Photoelectrochemical Water Oxidation

Density-functional theory (DFT) calculation reveals that the bandgap of barium bismuth niobate (Ba 2 BiNbO 6 ) double-perovskite oxide can be effectively narrowed if the oxide is made Bi-rich and Nb-poor. Material synthesis and characterization confirm the predictions from DFT calculation. The results of this study suggest a new strategy for bandgap engineering of metal oxides toward active photoanodes for efficient water-splitting applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗