Engineering topics

Zaman, K. B. M. Q.

Publications and source records attributed to Zaman, K. B. M. Q..

At least 55 records · Page 3

NASA NTRS2003

Synthetic Jets in Cross-flow: Jets From Orifices of Different Geometry - Part 2

The flow fields of synthetic jets in a cross-flow from orifices of different geometry are investigated. The geometries include a straight, a tapered, a pitched and a cluster of nine orifices, all having the same cross-sectional area through which the perturbation is discharged into the cross-flow. The strength of the jet from the tapered orifice in comparison to that from the straight one is found to be only slightly enhanced. The flow field from the cluster of orifices, when viewed a few equivalent diameters downstream, is similar to that from the single orifice. However, the penetration is somewhat lower in the former case due to the increased mixing of the distributed jets with the cross-flow. The penetration for the pitched configuration is the lowest, as expected. The jet trajectories for the straight and pitched orifices are well represented by correlation equations available for steady jets-in-cross-flow. Distributions of streamwise velocity, vorticity as well as turbulence intensity are documented for various cases. In addition, distributions of phase-averaged velocity and vorticity for the cylindrical and the clustered orifices are presented providing an insight into the flow dynamics.

Milanovic, Ivana M.↗

NASA NTRS2003

Synthetic Jets in Cross-flow: Round Jet - Part 1

Results of an experimental investigation on synthetic jets from round orifices with and without cross-flow are presented. Jet Reynolds number up to 46,000 with a fully turbulent approach boundary layer, and Stokes number up to 400. are covered. The threshold of stroke length for synthetic jet formation. in the absence of the cross-flow, is found to be Lo /D approximately 0.5. Above Lo /D is approximately 10, the profiles of normalized centerline mean velocity appear to become invariant. It is reasoned that the latter threshold may be related to the phenomenon of saturation of impulsively generated vortices. In the presence of the cross-flow, the penetration height of a synthetic jet is found to depend on the momentum- flux ratio . When this ratio is defined in terms of the maximum jet velocity and the cross-flow velocity. not only all data collapse but also the jet trajectory is predicted well by correlation equation available for steady jets-in-cross-flow. Distributions of mean velocity, streamwise vorticity as well as turbulence intensity for a synthetic jet in cross-flow are found to be similar to those of a steady jet-in-cross-flow. A pair of counter-rotating streamwise vortices, corresponding to the bound vortex pair of the steady case, is clearly observed. Mean velocity distribution exhibits a dome of low momentum fluid pulled up from the boundary layer, and the entire domain is characterized by high turbulence.

Zaman, K. B. M. Q.↗

NASA NTRS2002

A Quantitative Comparison of Leading-edge Vortices in Incompressible and Supersonic Flows

When requiring quantitative data on delta-wing vortices for design purposes, low-speed results have often been extrapolated to configurations intended for supersonic operation. This practice stems from a lack of database owing to difficulties that plague measurement techniques in high-speed flows. In the present paper an attempt is made to examine this practice by comparing quantitative data on the nearwake properties of such vortices in incompressible and supersonic flows. The incompressible flow data are obtained in experiments conducted in a low-speed wind tunnel. Detailed flow-field properties, including vorticity and turbulence characteristics, obtained by hot-wire and pressure probe surveys are documented. These data are compared, wherever possible, with available data from a past work for a Mach 2.49 flow for the same wing geometry and angles-of-attack. The results indicate that quantitative similarities exist in the distributions of total pressure and swirl velocity. However, the streamwise velocity of the core exhibits different trends. The axial flow characteristics of the vortices in the two regimes are examined, and a candidate theory is discussed.

Wang, F. Y.↗

NASA NTRS2002

Noise, Turbulence, and Thrust of Subsonic Free Jets from Lobed Nozzles

A study of noise benefit, vis-a-vis thrust penalty, and its correlation to turbulence intensities was conducted for free jets issuing from lobed nozzles. Four convergent nozzles with constant exit area were used in the experiments. Three of these were of rectangular lobed configuration having six, ten and fourteen lobes; the fourth was a circular nozzle. Increasing the number of lobes resulted in a progressive reduction in the turbulence intensities as well as in the overall radiated noise. The noise reduction was pronounced at the low frequency end of the spectrum. However, there was an increase in the high frequency noise that rendered the overall benefit less attractive when compared on a scaled-up A-weighted basis. A reduction in noise was accompanied by a commensurate reduction in the turbulent kinetic energy in the flow field. As expected, increasing the number of lobes involved progressive reduction in the thrust coefficient. Among the cases studied, the six-lobed nozzle had the optimum reduction in turbulence and noise with the least thrust penalty.

Zaman, K. B. M. Q.↗

NASA NTRS2002

Numerical Investigation of 'Transonic Resonance' with a Convergent-Divergent Nozzle

At pressure ratios lower than the design value, convergent-divergent (C-D) nozzles often undergo a flow resonance accompanied by the emission of acoustic tones. The phenomenon, driven by the unsteady shock within the divergent section of the nozzle, has been studied experimentally by Zaman et al. In this paper, the space-time conservation element solution element (CE/SE) method is employed to numerically investigate the phenomenon. The computations are performed for a given nozzle geometry for several different pressure ratios. Sustained 'limit cycle' oscillations are encountered in all cases. The oscillation frequencies, their variation with pressure ratio including a 'stage jump', agree well with the experimental results. The unsteady flow data confirm that stage 1 of the resonance (fundamental) involves a one-quarter standing wave while stage 2 (third harmonic) involves a three-quarter standing wave within the divergent section of the nozzle. Details of the shock motion, and the flow and near acoustic field, are documented for one case each of stages 1 and 2.

Loh, Ching Y.↗

NASA NTRS2002

Pitched and Yawed Circular Jets in Cross-Flow

Results from an experimental investigation of flow field generated by pitched and yawed jets discharging from a flat plate into a cross-flow are presented. The circular jet was pitched at alpha = 20 degrees and 45 degrees and yawed between beta = 0 degrees and 90 degrees in increments of 15 degrees. The measurements were performed with two X-wires providing all three components of velocity and turbulence intensity. These data were obtained at downstream locations of x = 3, 5, 10 and 20, where the distance x normalized by the jet diameter, is measured from the center of the orifice. Data for all configurations were acquired at a momentum-flux ratio J = 8. Additionally, for selected angles and locations, surveys were conducted for J = 1.5, 4, and 20. As expected, the jet penetration is found to be higher at larger alpha. With increasing beta the jet spreads more. The rate of reduction of peak streamwise vorticity, with the downstream distance is significantly lessened at higher alpha but is found to be practically independent of alpha. Thus, at the farthest measurement station x = 20, omega(sub xmax) is about five times larger for beta = 0 degrees compared to the levels at beta = 0 degrees. Streamwise velocity within the jet-vortex structure is found to depend on the parameter J. At J = 1.5 and 4, 'wake-like' velocity profiles are observed. In comparison, a 'jet-like' overshoot is present at higher J.

Milanovic, Ivana M.↗

NASA NTRS2001

Density Fluctuation in Asymmetric Nozzle Plumes and Correlation with Far Field Noise

A comparative experimental study of air density fluctuations in the unheated plumes of a circular, 4-tabbed-circular, chevron-circular and 10-lobed rectangular nozzles was performed at a fixed Mach number of 0.95 using a recently developed Rayleigh scattering based technique. Subsequently, the flow density fluctuations are cross-correlated with the far field sound pressure fluctuations to determine sources for acoustics emission. The nearly identical noise spectra from the baseline circular and the chevron nozzles are found to be in agreement with the similarity in spreading, turbulence fluctuations, and flow-sound correlations measured in the plumes. The lobed nozzle produced the least low frequency noise, in agreement with the weakest overall density fluctuations and flow-sound correlation. The tabbed nozzle took an intermediate position in the hierarchy of noise generation, intensity of turbulent fluctuation and flow-sound correlation. Some of the features in the 4-tabbed nozzle are found to be explainable in terms of splitting of the jet in a central large core and 4 side jetlets.

Panda, J.↗

NASA NTRS2001

Effect of Delta Tabs on Free Jets from Complex Nozzles

Effects of 'delta-tabs' on the mixing and noise characteristics of two model-scale nozzles have been investigated experimentally. The two models are (1) an eight-lobed nozzle simulating the primary flow of a mixer-ejector configuration considered for the HSCT program, (2) an axisymmetric nozzle with a centerbody simulating the 'ACE' configuration also considered for the HSCT program. Details of the flow-field for model (1) are explored, while primarily the noise-field is explored for model (2). Effects of different tab configurations are documented.

Zaman, K. B. M. Q.↗

NASA NTRS2001

Experimental Investigation of 'Transonic Resonance' with Convergent-Divergent Nozzles

Convergent-divergent nozzles, when run at pressure ratios lower than the design value, often undergo a flow resonance accompanied by the emission of acoustic tones. The phenomenon, different in characteristics from conventional 'screech' tones, has been studied experimentally. Unlike screech, the frequency increases with increasing supply pressure. There is a 'staging' behavior; 'odd harmonic' stages resonate at lower pressures while the fundamental occurs in a range of higher pressures corresponding to a fully expanded Mach number (M(sub j)) around unity. The frequency (f(sub N)) variation with M(sub j) depends on the half angle-of-divergence (theta) of the nozzle. At smaller theta, the slope of f(sub N) versus M(sub j) curve becomes steeper. The resonance involves standing waves and is driven by unsteady shock/boundary layer interaction. The distance between the foot of the shock and the nozzle exit imposes the lengthscale (L'). The fundamental corresponds to a quarterwave resonance, the next stage at a lower supply pressure corresponds to a three-quarter-wave resonance, and so on. The principal trends in the frequency variation are explained simply from the characteristic variation of the length-scale L'. Based on the data, correlation equations are provided for the prediction of f(sub N). A striking feature is that tripping of the boundary layer near the nozzle's throat tends to suppress the resonance. In a practical nozzle a tendency for the occurrence of the phenomenon is thought to be a source of 'internal noise'; thus, there is a potential for noise benefit simply by appropriate boundary layer tripping near the nozzle's throat.

Zaman, K. B. M. Q.↗

NASA NTRS2000

Study of Mixing Enhancement Observed with a Co-Annular Nozzle Configuration

Jet spreading enhancement with a certain coannular nozzle configuration has been explored. When the outer nozzle is flaired (i.e., made convergent-divergent) the ensuing jet spreads faster than the case where the outer nozzle is convergent. The spreading enhancement is most pronounced when the outer flow is run near 'transonic' condition, in an overexpanded state. Under this condition, the increased spreading takes place regardless of the operating conditions of the inner jet. This observation, first made in a small scale facility, has been confirmed and studied in some detail in a larger-scale facility. Results of the latter experiment are presented in this paper. The spreading increase is shown to be substantial and comparable to or better than that achieved by a lobed nozzle. Estimates based on idealized flow indicate that there is an accompanying thrust penalty - the actual penalty is expected to be less than the estimate but remains undetermined at this time. In both the earlier and the present experiments, the spreading increase has often been found to accompany a flow resonance. The nature of this resonance is addressed in this paper. It is shown that the spreading increase takes place even if the resonance is absent. Thus, flow excitation due to the resonance is ruled out as the underlying mechanism. While the complete mechanism remains unclear, it is conjectured that pressure gradients near the nozzle, characteristic of overexpanded flow, are at the root of the phenomenon.

Zaman, K. B. M. Q.↗

NASA NTRS1999

Mixing Enhancement in Supersonic Jets by Delta-Tabs

The investigation includes carry out fundamental experiments studying mechanisms of effect: (1) experiments on subsonic and supersonic jets to assess influence of compressibility, (2) parametric study on tab geometry to optimize effect for given flow blockage (this effort led to "delta-tab"), (3) quantify mixing enhancement in the jet, and (4) analyze mechanism of streamwise vorticity generation.

Zaman, K. B. M. Q.↗

NASA NTRS1999

Computation of Three-Dimensional Compressible Flow From a Rectangular Nozzle with Delta Tabs

A three-dimensional viscous flow analysis is performed using a time-marching Reynolds-averaged Navier-Stokes code for a 3:1 rectangular nozzle with two delta tabs located at the nozz1e exit plane to enhance mixing. Two flow configurations, a subsonic jet case and a supersonic jet case using the same rate configuration, which were previously studied experimentally, are computed and compared with the experimental data. The experimental data include streamwise velocity and vorticity distributions for the subsonic case, and Mach number distributions for the supersonic case, at various axial locations downstream of the nozzle exit. The computational results show very good agreement with the experimental data. In addition, the effect of compressibility on vorticity dynamics is examined by comparing the vorticity contours of the subsonic jet case with those of the supersonic jet case which were not measured in the experiment.

Reddy, D. R.↗

NASA NTRS1999

Subsonic Jet Noise from Non-Axisymmetric and Tabbed Nozzles

Subsonic jet noise from non-axisymmetric and tabbed nozzles are investigated experimentally and theoretically. It is shown that the noise spectra of these jets are in good agreement with the similarity spectra found empirically earlier by Tam, Golebiowski and Seiner through a detailed analysis of supersonic jet noise data. Further, the radiated noise fields of the jets under study, including elliptic and large aspect ratio rectangular jets, are found to be quite axisymmetric and are practically the same as that of a circular jet with the same exit area. These experimental results strongly suggest that nozzle geometry modification into elliptic or rectangular shapes is not an effective method for jet noise suppression. A lobed nozzle, on the other hand, is found to significantly impact the noise field. Noise from large scale turbulent structures, radiating principally in the downstream direction, is effectively suppressed. Tabs also impact the noise field, primarily by shifting the spectral peak to a higher frequency. A jetlets model is developed to provide a basic understanding of the noise from tabbed jets. The model predicts that the noise spectrum from a jet with N tabs (N greater than or equal to 2) can be obtained from that of the original jet (no tab) by a simple frequency shift. The shifted frequency is obtained by multiplying the original frequency by N(exp 1/2). This result is in fairly good agreement with experimental data.

Tam, Christopher K. W.↗

NASA NTRS1999

Aeroacoustic Resonance with Convergent-Divergent Nozzles

Convergent-divergent nozzles, when run at off-design conditions, often undergo flow resonance accompanied by the emission of a tone. Apart from screech occurring at higher operating pressures, resonance is also common at lower Mach numbers near transonic as well as subsonic conditions. With data from six nozzles of different size and design Mach number, the present paper documents the characteristics of the latter phenomenon that is morphologically quite different from conventional screech. The resonance is due to a feedback loop internal to the nozzle and is apparently driven by unsteady laminar boundary layer separation near the throat of the nozzle. Appropriate boundary layer tripping prior to the throat is found to eliminate or alter most of the tones. The Helmholtz number of the resonance, based on the throat-to-exit length, is found to attain a value of approximately 0.15 at M(sub j)=1 for all nozzles. However, its variation with M(sub j) may be different and depend on the nozzle geometry. With nozzles having larger throat-to-exit angle of divergence, the frequency is found to increase, in some cases having stage jumps to lower frequencies, with increasing operating pressure. With nozzles having smaller angle of divergence, the frequency variation exhibits an increase followed by a decrease involving one prominent stage occurring around transonic (M(sub j)= 1) condition. While the mechanisms remain far from completely clear, a model involving downstream propagating aerodynamic disturbance together with acoustic feedback explains the overall frequency characteristics for most cases.

Zaman, K. B. M. Q.↗

NASA NTRS1999

Jet Spreading Increase by Passive Control and Associated Performance Penalty

This paper reviews the effects of 'screech', 'asymmetric nozzle shaping', 'tabs' and 'overexpansion' on the spreading of free jets. Corresponding thrust penalty for the tabs and overexpanded condition are also evaluated. The asymmetric shapes include rectangular ones with varying aspect ratio. Tabs investigated are triangular shaped 'delta-tabs' placed at the exit of a convergent circular nozzle. The effect of overexpansion is examined with circular convergent-divergent (C-D) nozzles. Tabs and overexpansion are found to yield the largest increase in jet spreading. Each, however, involves a performance penalty, i.e., a loss in thrust coefficient. Variation of the size of four delta-tabs show that there exists an optimum size for which the gain in jet spreading is the maximum per unit loss in thrust coefficient. With the C-D nozzles, the minimum in thrust coefficient is expected near the beginning of the overexpanded regime based on idealized flow calculations. The maximum increase in jet spreading, however, is found to occur at higher pressure ratios well into the overexpanded regime. The optimum benefit with the overexpanded flow, in terms of gain in spreading for unit penalty, is found to be comparable to the optimum tab case.

Zaman, K. B. M. Q.↗

NASA NTRS1999

Subsonic Jet Noise from Non-Axisymmetric and Tabbed Nozzles

Subsonic jet noise from non-axisymmetric and tabbed nozzles are investigated experimentally and theoretically. It is shown that the noise spectra of these jets are in good agreement with the similarity spectra found empirically earlier by Tam, Golebiowski and Seiner through a detailed analysis of supersonic jet noise data. Further, the radiated noise fields of the jets under study, including elliptic and large aspect ratio rectangular jets, are found to be quite axisymmetric and are practically the same as that of a circular jet with the same exit area. These experimental results strongly suggest that nozzle geometry modification into elliptic or rectangular shapes is not an effective method for jet noise suppression. A lobed nozzle, on the other hand, is found to significantly impact the noise field. Noise from large scale turbulent structures, radiating principally in the downstream direction, is effectively suppressed. Tabs also impact the noise field, primarily by shifting the spectral peak to a higher frequency. A jetlets model is developed to provide a basic understanding of the noise from tabbed jets. The model predicts that the noise spectrum from a jet with N tabs (N > 2) can be obtained from that of the original jet (no tab) by a simple frequency shift. The shifted frequency is obtained by multiplying the original frequency by N(sup 1/2). This result is in fairly good agreement with experimental data.

Zaman, K. B. M. Q.↗

NASA NTRS1999

Spreading Characteristics of Compressible Jets from Nozzles of Various Geometries

The spreading characteristics of jets from several asymmetric nozzles, and a set of rectangular orifices are compared, covering a jet Mach number range of 0.3-2.0. The effect of 'tabs' for a rectangular and a round nozzle is also included in the comparison. Compared to a round jet, the jets from the asymmetric nozzles spread only slightly more at subsonic conditions whereas at supersonic conditions, when 'screech' occurs, they spread much more. The dynamics of the azimuthal vortical structures of the jet, organized and intensified under the screeching condition, are thought to be responsible for the observed effect at supersonic conditions. Curiously, the jet from a 'lobed' nozzle spreads much less at supersonic condition compared to all other cases; this is due to the absence of screech with this nozzle. Screech stages inducing flapping, rather than varicose or helical, flow oscillation cause a more pronounced jet spreading. At subsonic conditions, only a slight increase in jet spreading with the asymmetric nozzles contrasts previous observations by others. The present results show that the spreading of most asymmetric jets is not much different from that of a round jet. This inference is further supported by data from the rectangular orifices. In fact, jets from the orifices with small aspect ratio (AR) exhibit virtually no increase in the spreading. A noticeable increase commences only when AR is larger than about 10. Thus, 'shear layer perimeter stretching', achieved with a larger AR for a given cross-sectional area of the orifice, by itself, proves to be a relatively inefficient mechanism for increasing jet spreading. In contrast, the presence of streamwise vortices or 'natural excitation' can cause a significant increase - effects that might explain the observations in the previous investigations. Thus far, the biggest increase in jet spreading is observed with the tabs. This is true in the subsonic regime, as well as in the supersonic regime, in spite of the fact that screech is eliminated by the tabs. The characteristic spreading of the tabbed jets is explained by the induced motion of the tab-generated streamwise vortex pairs. The tabs, however, incur thrust loss; the flow blockage and loss in thrust coefficient, vis-a-vis the spreading increase, are evaluated for various configurations.

Zaman, K. B. M. Q.↗

NASA NTRS1998

Asymptotic Spreading Rate of Initially Compressible Jets: Experiment and Analysis

Experimental results for the spreading and centerline velocity decay rates for round, compressible jets, from a convergent and a convergent-divergent nozzle, are presented. The spreading rate is determined from the variation of streamwise mass flux obtained from Pitot probe surveys. Results for the far asymptotic region show that both spreading and centerline velocity decay rates, when nondimensionalized by parameters at the nozzle exit, decrease with increasing "jet Mach number" M(sub J). Dimensional analysis with the assumption of momentum conservation, together with compressible flow calculations for the conditions at the nozzle exit, predict this Mach number dependence well. The analysis also demonstrates that an increase in the "potential core length" of the jet occurring with increasing M(sub J), a commonly observed trend, is largely accounted for simply by the variations in the density and static pressure at the nozzle exit. The effect of decreasing mixing efficiency with increasing compressibility is inferred to contribute only partially to the latter trend.

Zaman, K. B. M. Q.↗