Engineering topics

Zaman, K. B. M. Q.

Publications and source records attributed to Zaman, K. B. M. Q..

At least 73 records · Page 4

NASA NTRS1998

Asymptotic Spreading Rate of Initially Compressible Jets-Experiment and Analysis

Experimental results for the spreading and centerline velocity decay rates for round, compressible jets, from a convergent and a convergent-divergent nozzle, are presented. The spreading rate is determined from the variation of streamwise mass flux obtained from Pitot probe surveys. Results for the far asymptotic region show that both spreading and centerline velocity decay rates, when nondimensionalized by parameters at the nozzle exit, decrease with increasing "jet Mach number" M(sub j). Dimensional analysis with the assumption of momentum conservation, together with compressible flow calculations for the conditions at the nozzle exit, predict this Mach number dependence well. The analysis also demonstrates that an increase in the "potential core length" of the jet occurring with increasing M(sub j), a commonly observed trend, is largely accounted for simply by the variations in the density and static pressure at the nozzle exit. The effect of decreasing mixing efficiency with increasing compressibility is inferred to contribute only partially to the latter trend.

Zaman, K. B. M. Q.↗

NASA NTRS1998

Reduction of Jet Penetration in a Cross-Flow by Using Tabs

A tab placed suitably on a nozzle that produces a jet in a cross-flow can reduce the penetration of the jet. This effect, achieved when the tab is placed on the windward side of the nozzle relative to the cross flow, may be of interest in film cooling applications. Wind tunnel experiments are carried out, in the momentum ratio (J) range of 10-90, to investigate the tab geometry that would maximize this effect. The preliminary results show that a 'delta tab' having a base width approximately fifty percent of the nozzle diameter may be considered optimum. With a given tab size, the effect is more pronounced at higher J. Reduction in jet penetration by as much as 40% is observed. Comparable reduction in jet penetration is also obtained when a triangular shaped tab is placed flush with the tunnel wall or with its apex tilted down into the jet nozzle (the 'delta tab' being the configuration in which the apex is tilted up). However, the delta tab involves the least flow blockage and pressure loss. Relative to the baseline case, the lateral spreading of the jet is found to be more with the delta tab but less with other orientations of the tab.

Zaman, K. B. M. Q.↗

NASA NTRS1998

Characterization of Asymptotic Entrainment Rate for Compressible Jets

Experimental results for the spreading and centerline velocity decay rates are presented for round, compressible, submerged jets, with total temperature same as ambient temperature, covering a 'jet Mach number' (M(sub J)) range of 0.3 - 2.0. Data from a convergent and a convergent-divergent nozzle are considered. The spreading rate is determined from the total longitudinal mass fluxes measured by Pilot probe survey. Results for the far asymptotic regions show that both spreading and centerline velocity decay rates, when normalized by conditions at the nozzle exit, decrease with increasing M(sub J). Dimensional analysis and isentropic calculations predict this Mach number dependence well. The analysis also demonstrates that an increase in the 'potential core length' of the jet occurring with increasing M(sub J), a commonly observed trend, is largely accounted for simply by the variations in the density and static pressure at the nozzle exit. The effect of decreasing mixing efficiency with increasing compressibility is inferred to contribute only partially to the latter trend.

Zaman, K. B. M. Q.↗

NASA NTRS1997

Reversal in Spreading of a Tabbed Circular Jet Under Controlled Excitation

Detailed flow field measurements have been carried out for a turbulent circular jet perturbed by tabs and artificial excitation. Two "delta tabs" were placed at the nozzle exit at diametrically opposite locations. The excitation condition involved subharmonic resonance that manifested in a periodic vortex pairing in the near flow field. While the excitation and the tabs independently increased jet spreading, a combination of the two diminished the effect. The jet spreading was most pronounced with the tabs but was reduced when excitation was applied to the tabbed jet. The tabs generated streamwise vortex pairs that caused a lateral spreading of the jet in a direction perpendicular to the plane containing the tabs. The excitation, on the other band, organized the azimuthal vorticity into coherent ring structures whose evolution and pairing also increased entrainment by the jet. In the tabbed case, the excitation produced coherent azimuthal structures that were distorted and asymmetric in shape. The self-induction of these structures produced an effect that opposed the tendency for the lateral spreading of the streamwise vortex pairs. The passage of the distorted vortices, and their pairing, also had a cancellation effect on the time-averaged streamwise vorticity field. These led to the reduction in jet spreading.

Zaman, K. B. M. Q.↗

NASA NTRS1997

Reversal in Spreading of a Tabbed Circular Jet Under Controlled Excitation

Detailed flow field measurements have been carried out for a turbulent circular jet perturbed by tabs and artificial excitation. Two "delta tabs" were placed at the nozzle exit at diametricall opposite y locations. The excitation condition involved subharmonic resonance that manifested in a periodic vortex pairing in the near flow field. While the excitation and the tabs independently increased jet spreading, a combination of the two diminished the effect. The jet spreading was most pronounced with the tabs but was reduced when excitation was applied to the tabbed jet. The tabs generated streamwise vortex pairs that caused a lateral spreading of the jet in a direction perpendicular to the plane containing the tabs. ne excitation, on the other hand, organized the azimuthal vorticity into coherent ring structures whose evolution and pairing also increased entrainment by the jet. In the tabbed case, the excitation produced coherent azimuthal structures that were distorted and asymmetric in shape. The self-induction of these structures produced an effect that opposed the tendency for the lateral spreading of the streamwise vortex pairs. The passage of the distorted vortices, and their pairing, also had a cancellation effect on the time-averaged streamwise vorticity field. These led to the reduction in jet spreading.

Zaman, K. B. M. Q.↗

NASA NTRS1997

Optimal Configuration of an Array of Tabs for Mixing Enhancement in a Shear Layer

The large and small scale vortical motions produced by delta tabs in a two-stream shear layer have been studied experimentally. The tabs were placed at the trailing edge of a splitter plate, mounted in the test section of a wind tunnel, that produced the shear layer. Hot-wire measurements detailed the velocity, vorticity and small scale population distributions in the 3-D space behind the tabs. Small scale structures, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. The optimal tab inclination angle, theta, and the optimal spanwise spacing, S, for a multiple tab array were identified. The optimal condition was that which maximized the small scale population and generated the strongest streamwise vorticity. Increasing the tab pitch angle from flush to normal to the splitter plate increased the streamwise vorticity as well as the overall small scale population. In fact, the increase in the overall small scale population correlated strongly with the increase in streamwise vorticity intensity. The optimal conditions for peak streamwise vorticity and peak small scale population, with minimum area blockage, were determined to be theta = 45deg and S = 1.5 tab widths.

Foss, J. K.↗

NASA NTRS1997

The Effect of Vortex Generators on a Jet in a Cross-Flow

The effect of vortex generators in the form of tabs on the penetration and spreading of a jet in a cross-flow has been studied experimentally. It is found that the tab has very little effect when placed on the leeward side, i.e., on the downstream edge of the jet nozzle relative to the free-stream flow. A study of the static pressure distribution reveals significantly lower pressures on the leeward side. Thus, when placed on that side the tab does not produce a "pressure hill" of sufficient magnitude that is the primary source of streamwise vorticity in the flow field over the tab. This qualitatively explains the ineffectiveness. In comparison, there is a significant effect on the flow field when the tab is placed on the windward side, The sense of vorticity generated by the tab in the latter configuration is opposite to that of the bound vortex pair that otherwise characterizes the flow. Thus, the strength of the bound vortex pair is diminished and the jet penetration is reduced.

Zaman, K. B. M. Q.↗

NASA NTRS1997

Effect of Controlled Excitation on a Tabbed Jet

Detailed flowfield measurements have been carried out for a turbulent circular jet perturbed by tabs and artificial excitation. The excitation condition involved subharmonic resonance which manifested in a periodic vortex pairing in the near flowfield. While the excitation and the tabs independently increased jet spreading, a combination of the two diminished the effect. The jet spreading was the most with the tabs, but was reduced when excitation was applied to the tabbed jet. The self-induction of the distorted azimuthal vortex rings during the pairing process weakened the streamwise vortices produced by the tabs to cause this effect.

Zaman, K. B. M. Q.↗

NASA NTRS1996

Effect of a delta tab on fine scale mixing in a turbulent two-stream shear layer

The fine scale mixing produced by a delta tab in a shear layer has been studied experimentally. The tab was placed at the trailing edge of a splitter plate which produced a turbulent two-stream mixing layer. The tab apex tilted downstream and into the high speed stream. Hot-wire measurements in the 3-D space behind the tab detailed the three velocity components as well as the small scale population distributions. These small scale eddies, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. It was found that the small scale populations were greater in the shear region behind the tab, with the greatest increase occurring where the shear layer underwent a sharp turn. This location was near, but not coincident, with the core of the streamwise vortex, and away from the region exhibiting maximum turbulence intensity. Moreover, the tab increased the most probably frequency and strain rate of the small scales. It made the small scales smaller and more energetic.

Foss, J. K.↗

NASA NTRS1995

Spreading Characteristics and Thrust of Jets from Asymmetric Nozzles

The spreading characteristics of jets from several asymmetric nozzles are studied in comparison to those of an axisymmetric jet, over the Mach number (M(sub J)) range of 0.3 to 1.96. The effect of tabs in two cases, the axisymmetric nozzle fitted with four tabs and a rectangular nozzle fitted with two large tabs, is also included in the comparison. Compared to the axisymmetric jet, the asymmetric jets spread only slightly faster at subsonic conditions, while at supersonic conditions, when screech occurs, they spread much faster. Screech profoundly increases the spreading of all jets. The effect varies in the different stages of screech, and the corresponding unsteady flowfield characteristics are documented via phase-averaged measurement of the fluctuating total pressure. An organization and intensification of the azimuthal vortical structures under the screeching condition is believed to be responsible for the increased spreading. Curiously, the jet from a 'lobed mixer' nozzle spreads much less at supersonic conditions compared to all other cases. This is due to the absence of screech with this nozzle. Jet spreading for the two tab configurations, on the other hand, is significantly more than any of the no-tab cases. This is true in the subsonic regime, as well as in the supersonic regime in spite of the fact that screech is essentially eliminated by the tabs. The dynamics of the streamwise vortex pairs produced by the tabs cause the most efficient jet spreading thus far observed in the study.

Zaman, K. B. M. Q.↗

NASA NTRS1994

Axis switching and spreading of an asymmetric jet: Role of vorticity dynamics

The effects of vortex generators and periodic excitation on vorticity dynamics and the phenomenon of axis switching in a free asymmetric jet are studied experimentally. Most of the data reported are for a 3:1 rectangular jet at a Reynolds number of 450,000 and a Mach number of 0.31. The vortex generators are in the form of 'delta tabs', triangular shaped protrusions into the flow, placed at the nozzle exit. With suitable placement of the tabs, axis switching could be either stopped or augmented. Two mechanisms are identified governing the phenomenon. One, as described by previous researchers and referred to here as the omega(sub theta)-induced dynamics, is due to difference in induced velocities for different segments of a rolled up azimuthal vortical structure. The other, omega(sub x)-induced dynamics, is due to the induced velocities of streamwise vortex pairs in the flow. Both dynamics can be active in a natural asymmetric jet; the tendency for axis switching caused by the omega(sub theta)-induced dynamics may be, depending on the streamwise vorticity distribution, either resisted or enhanced by the omega(sub x)-induced dynamics. While this simple framework qualitatively explains the various observations made on axis switching, mechanisms actually in play may be much more complex. The two dynamics are not independent as the flow field is replete with both azimuthal and streamwise vortical structures which continually interact. Phase averaged flow field data for a periodically forced case, over a volume of the flow field, are presented and discussed in an effort to gain insight into the dynamics of these vortical structures.

Zaman, K. B. M. Q.↗

NASA NTRS1994

Control of an Axisymmetric Jet Using Vortex Generators

The results of an experimental investigation on the effect of vortex generators, in the form of small tabs at the nozzle exit on the evolution of a jet, are reported in this paper. Primarily tabs of triangular shape are considered, and the effect is studied up to a jet Mach number of 1.8. Each tab is found to produce a dominant pair of counter-rotating streamwise vortices having a sense of rotation opposite to that expected from the wrapping of the boundary layer. This results in an inward indentation of the mixing layer into the core of the jet. A triangular-shaped tab with its apex leaning downstream, referred to as a delta tab, is found to be the most effective in producing such vortices, with a consequential large influence on the overall jet evolution. Two delta tabs, spaced 180 deg apart, completely bifurcate the jet. Four delta tabs stretch the mixing layer into four 'fingers,' resulting in a significant increase in the jet mixing downstream. For six delta tabs the mixing layer distortion settles back to a three finger configuration through an interaction of the streamwise vortices. The tabs are found to be equally effective in jets with turbulent or laminar initial boundary layers. Two sources of streamwise vorticity are postulated for the flow under consideration. One is the upstream 'pressure hill,' generated by the tab, which constitutes the main contributor of vorticity to the dominant pair. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. Depending on the orientation of the tab, the latter source can produce a vortex pair having a sense of rotation opposite to that of the dominant pair. In the case of the delta tab, vorticity from the two sources add, explaining the strong effect in that configuration.

Zaman, K. B. M. Q.↗

NASA NTRS1994

Effect of delta tabs on mixing and axis switching in jets from asymmetric nozzles

The effect of delta tabs on mixing and the phenomenon of axis switching in free air jets from various asymmetric nozzles was studied experimentally. Flow visualization and Pitot probe surveys were carried out with a set of small nozzles (D = 1.47 cm) at a jet Mach number, Mj = 1.63. Hot wire measurements for streamwise vorticity were carried out with larger nozzles (D = 6.35 cm) at Mj = 0.31. Jet mixing with the asymmetric nozzles, as indicated by the mass fluxes downstream, was found to be higher than that produced by a circular nozzle. The circular nozzle with four delta tabs, however, produced fluxes much higher than that produced by a asymmetric nozzles themselves or by most of the tab configurations tried with them. Even higher fluxes could be obtained with only a few cases, e.g., with 3:1 rectangular nozzle with two large delta tabs placed on the narrow edges. In this case, the jet 'fanned out' at a large angle after going through one axis switch. The axis switching could be either stopped or augmented with suitable choice of the tab configurations. Two mechanisms are identified governing the phenomenon. One, as described in Ref. 12 and referred to here as the omega(sub Theta)-induced dynamics, is due to differential induced velocities of different segments of a rolled up azimuthal vortical structure. The other is the omega(sub x)-induced dynamics due to the induced velocities of streamwise vortex pairs in the flow. While the former dynamics are responsible for rapid axis switching in periodically forced jets, the effect of the tabs is governed mainly by the latter. It is inferred that both dynamics are active in a natural asymmetric jet issuing from a nozzle having an upstream contraction. The tendency for axis switching caused by the omega(sub Theta)-induced dynamics is resisted by the omega(sub x)-induced dynamics, leading to a delayed or no switch over in that case. In jets from orifices and in screeching jets, the omega(sub Theta)-induced dynamics dominate causing a faster switch over.

Zaman, K. B. M. Q.↗

NASA NTRS1993

Streamwise vorticity generation and mixing enhancement in free jets by 'delta-tabs'

The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the streamwise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.

Zaman, K. B. M. Q.↗

NASA NTRS1993

Streamwise vorticity generation and mixing enhancement in free jets by delta-tabs

The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the stream wise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.

Zaman, K. B. M. Q.↗

NASA NTRS1993

Effect of tabs on the flow and noise field of an axisymmetric jet

The effect of vortex generators, in the form of small tabs projecting normally into the flow at the nozzle exit, on the characteristics of an axisymmetric jet is investigated experimentally over the jet Mach number range of 0.3-1.81. The tabs eliminate screech noise from supersonic jets and alter the shock structure drastically. They distort the jet cross section and increase the jet spread rate significantly. The distortion produced is essentially the same at subsonic and underexpanded supersonic conditions. Thus, the underlying mechanism must be independent of compressibility effects. A tab with a height as small as 2 percent of the jet diameter, but larger than the efflux boundary-layer thickness, is found to produce a significant effect. Flow visualization reveals that each tab introduces an 'indentation' into the high speed side of the shear layer via the action of streamwise vortices. These vortices are inferred to be of the 'trailing vortex' type rather than of the 'necklace vortex' type. It is apparent that a substantial pressure differential must exist between the upstream and the downstream sides of the tab to effectively produce these trailing vortices. This explains why the tabs are ineffective in the overexpanded flow, as in that case an adverse pressure gradient exists near the nozzle exit which reduces the pressure differential produced by the tab.

Samimy, M.↗

NASA NTRS1993

Estimation of unsteady lift on a pitching airfoil from wake velocity surveys

The results of a joint experimental and computational study on the flowfield over a periodically pitched NACA0012 airfoil, and the resultant lift variation, are reported in this paper. The lift variation over a cycle of oscillation, and hence the lift hysteresis loop, is estimated from the velocity distribution in the wake measured or computed for successive phases of the cycle. Experimentally, the estimated lift hysteresis loops are compared with available data from the literature as well as with limited force balance measurements. Computationally, the estimated lift variations are compared with the corresponding variation obtained from the surface pressure distribution. Four analytical formulations for the lift estimation from wake surveys are considered and relative successes of the four are discussed.

Zaman, K. B. M. Q.↗

NASA NTRS1993

Estimation of unsteady lift on a pitching airfoil from wake velocity surveys

Zaman, K. B. M. Q.↗