Engineering topics

Zhang, Yifan

Publications and source records attributed to Zhang, Yifan.

23 records · Page 2

DOE OSTI2022

Fragmentation of the edge of a terminated Cu nanolayer within a Nb matrix upon annealing

Here, we investigate the evolution of the tip of a terminated Cu nano-layer embedded within a Nb matrix upon annealing at 800°C. The tip of the terminated Cu layer fragments progressively into a series of single-crystal Cu particles upon continued annealing. This finding shows that layer fragmentation is the second step, after layer pinchoff, in the thermal coarsening of nanolayered metal composites. Comparison to prior phase-field modeling permits us to infer that the mobility at 800°C of Cu-Nb, as modeled by the Cahn-Hillard equation, is M(c)=(M 0 = 7.3 ± 3.6 nm 5 / s • eV) |1 – c 2 |, where the order parameter, c, is 1 for Cu and -1 for Nb.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In situ study on heavy ion irradiation induced microstructure evolution in single crystal Cu with nanovoids at elevated temperature

Understanding the response of nanovoids to irradiation damage advances our capability to design radiation tolerant materials. Recent in situ studies reveal the shrinkage of hexagon-shaped nanovoids in (110) textured Cu. However, the evolution of voids with irregular geometries under irradiation is less well understood. Here, in situ Kr ion irradiation was performed at 100 °C on single-crystal Cu (112) that possesses nanovoids with high aspect ratio. In situ studies show these elongated voids fragment into smaller voids and shrink gradually with increasing dose. Phase field simulations confirm that fragmentation of the void is governed by the competing kinetics between atoms diffusing toward and away from the elongated nanovoid. In conclusion, cost irradiation analysis reveals the formation of high-density defect clusters.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2022

Kink mechanism in Cu/Nb nanolaminates explored by $\mathcal{in}$ $\mathcal{situ}$ pillar compression

We report Nano metallic laminates (NMLs) exhibit different failure modes depending on the loading conditions due to their mechanical anisotropies. Kinking is a typical failure mode in many NMLs compressed along a layer-parallel direction. However, a detailed description of the microstructure evolution during kink band (KB) formation and an in-depth understanding of the formation mechanisms are lacking. In this work, the KB process is investigated in Cu/Nb NMLs by in situ micro pillar compression in the scanning electron microscope (SEM) along a layer-parallel direction. Post-mortem S/TEM and transmission Kikuchi diffraction (TKD) analyses show that kink banding leads to significant microstructure changes characterized by an accumulation of geometrically necessary dislocations (GNDs) and of tilt geometrically necessary boundaries (GNBs) near KB boundaries (KBBs). The distinct microstructure evolution implies that KB formation is facilitated by the inhomogeneous microstructures resulting in constrained deformation modes. Specifically, dislocations active on slip planes nearly parallel to the interfaces make a major contribution to kink evolution after the onset of kinking. Once layer-parallel slip systems are activated, preexisting lattice dislocations and dislocations nucleating from interfaces will accumulate as GNDs near KBBs via the stochastic storage of lattice dislocations that have certain Burgers vectors. GNDs can further transform into GNBs via cross-slip and climb driven processes near the KBB. Furthermore, GNBs near KBBs can grow by incorporating more GNDs or by coalescence to accommodate the KB evolution. We further hypothesize that microstructural perturbations and their ensuing stresses can initiate KB formation in Cu/Nb NMLs.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Tribological behaviors of nanotwinned Al alloys

Wear-induced damages cause significant materials loss each year. Al alloys are widely used by industry but usually have low wear resistance. Here, we compare the tribological behaviors of ultrafine grained Al, a nanoprecipitate hardened Al 7075 alloy and nanotwinned Al–Ni alloys using the nanoscratch. The nanotwinned Al–Ni alloys exhibit lower coefficient of friction and much greater wear resistance than the Al and Al 7075 alloys. Additionally, the enhanced wear properties of Al–Ni alloys arise from their high strength and the evolution of nanotwinned microstructures into gradient nanograins during wear. These findings on fundamental wear mechanisms in nanotwinned alloys may advance the discovery of wear-resistant metallic materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The PagKNAT2/6b-PagBOP1/2a Regulatory Module Controls Leaf Morphogenesis in Populus

Leaf morphogenesis requires precise regulation of gene expression to achieve organ separation and flat-leaf form. The poplar KNOTTED-like homeobox gene PagKNAT2/6b could change plant architecture, especially leaf shape, in response to drought stress. However, its regulatory mechanism in leaf development remains unclear. In this work, gene expression analyses of PagKNAT2/6b suggested that PagKNAT2/6b was highly expressed during leaf development. Moreover, the leaf shape changes along the adaxial-abaxial, medial-lateral, and proximal-distal axes caused by the mis-expression of PagKNAT2/6b demonstrated that its overexpression (PagKNAT2/6b OE) and SRDX dominant repression (PagKNAT2/6b SRDX) poplars had an impact on the leaf axial development. The crinkle leaf of PagKNAT2/6b OE was consistent with the differential expression gene PagBOP1/2a (BLADE-ON-PETIOLE), which was the critical gene for regulating leaf development. Further study showed that PagBOP1/2a was directly activated by PagKNAT2/6b through a novel cis-acting element “CTCTT”. Together, the PagKNAT2/6b-PagBOP1/2a module regulates poplar leaf morphology by affecting axial development, which provides insights aimed at leaf shape modification for further improving the drought tolerance of woody plants.

59 BASIC BIOLOGICAL SCIENCES↗