Search NASA⌕ Search

Engineering topics

Zhang, Yuxuan

Publications and source records attributed to Zhang, Yuxuan.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Metal–Organic Framework-derived Atomic Metal Sites Promoting Sulfur Cathode for All-Solid-State Lithium–Sulfur Batteries

All-solid-state lithium–sulfur batteries (ASSLSBs) offer high energy density and intrinsic safety; however, they still face major challenges, including sluggish redox kinetics and poor sulfur utilization. Incorporating conductive materials into sulfur cathodes is an effective strategy to mitigate these limitations. Here, a highly conductive cobalt–nitrogen–doped carbon (Co–NC) derived from a metal–organic framework (MOF) is introduced to accelerate charge transfer and promote reversible sulfur conversion. Co−NC provides atomically dispersed Co–N sites and conductive carbon pathways that correlate with improved charge transfer, sulfur utilization, and rate capability. Co–NC@S cathode delivers 1499 mAh g–1 at C/20 with a high sulfur loading (5 mg cm–2) and retains 1292 mAh g–1 after five cycles (vs 443 mAh g–1 without Co–NC). Moreover, Co–NC derived ASSLSB achieves 903 mAh g–1 at 5C at 60 °C. This work provides a practical and effective approach to develop high energy, high-rate ASSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Adsorptive behavior of poly (vinylidene fluoride) membranes for the recovery of lignin-derived hydrophobic deep eutectic solvents

Abstract Recently, membrane technology has gained significant traction as an energy-efficient alternative to traditional thermal processes for solvent recovery. Deep eutectic solvents (DESs) have emerged as sustainable alternatives to conventional organic solvents, yet a systematic methodology for selecting compatible membrane materials for their recovery remains underdeveloped. This study established a predictive framework for membrane material selection in hydrophobic DES applications using Hansen Solubility Parameters (HSP) with inverted criteria targeting materials with relative energy difference (RED) values greater than 1.0. Flat sheet membranes were fabricated via the non-solvent induced phase separation (NIPS) technique. Four NIPS fabricated polymer membranes were evaluated: polysulfone, cellulose acetate, polyvinylidene fluoride (PVDF) fabricated with polyethylene glycol (PEG) as a pore-forming agent, and polybenzimidazole (PBI). The HSP approach successfully predicted membrane-solvent compatibility, with polysulfone (RED = 0.6) and cellulose acetate (RED = 0.9) dissolving completely within 24 h, while PVDF (RED = 1.9) and PBI (RED = 1.1) maintained structural integrity throughout a 7-day exposure period. Furthermore, PVDF demonstrated superior performance with minimal weight gain (3.0%), hydrophobic surface characteristics (122° water contact angle), and enhanced mechanical properties following DES exposure. Comprehensive chemical and morphological characterization confirmed PVDF’s chemical stability and revealed a surface-selective interaction mechanism involving simultaneous PEG (pore-forming agent) extraction and DES component adsorption. Adsorption kinetics followed pseudo-first-order behavior with reversible characteristics, best described by the Temkin isotherm model (R² = 0.9987). PVDF membranes-maintained separation functionality with average lignin rejection (75.2 ± 7.69%) and demonstrated filtration permeability of 2.0 ± 0.34 LMH/bar. This methodology provides a rational approach for membrane selection in emerging solvent systems, contributing to the advancement of sustainable separation technologies for DES-based biomass processing applications.

Science & Technology - Other Topics↗
DOE OSTI2024

Quantitative near-field water–air spray measurements at elevated pressures by neutron radiography imaging

Extensive experimental research on high-pressure spray has been conducted for decades to deepen our understanding and optimize its use in transportation, aviation, and propulsion applications; however, the near-field and in-nozzle flow characteristics are not fully understood. Dense near-field spray is among the most challenging diagnostic tasks since light is severely scattered and diffused by the liquid droplets and columns. In this work, the near-field spray and in-nozzle flow characteristics of an aeration nozzle at elevated pressures were characterized by neutron radiography imaging at the Oak Ridge National Laboratory High Flux Isotope Reactor. Neutron imaging benefits via strong penetration depths for some metals (i.e., aluminum, lead, and steel) and is sufficiently sensitive to detection of light elements, especially for hydrogen-based molecules, due to the large incoherent scattering cross section of neutrons. Both two-dimensional snapshots of the near-field spray and a three-dimensional tomographic scan of the nozzle geometry and in-nozzle water were obtained. This work provides new quantitative characterization of practical metal nozzle geometry for accurate boundary conditions, internal flow patterns inside the nozzle, and high-pressure spray flows. In conclusion, the findings may be used to improve performance and operating conditions of transportation vehicles and propulsion systems.

42 ENGINEERING↗
DOE OSTI2024

Porous Iron Electrodes Reduce Energy Consumption During Electrocoagulation of a Virus Surrogate: Insights into Performance Enhancements Using Three-Dimensional Neutron Computed Tomography

Electrocoagulation has attracted significant attention as an alternative to conventional chemical coagulation because it is capable of removing a wide range of contaminants and has several potential advantages. In contrast to most electrocoagulation research that has been performed with nonporous electrodes, in this study, we demonstrate energy-efficient iron electrocoagulation using porous electrodes. In batch operation, investigation of the external pore structures through optical microscopy suggested that a low porosity electrode with sparse connection between pores may lead to mechanical failure of the pore network during electrolysis, whereas a high porosity electrode is vulnerable to pore clogging. Electrodes with intermediate porosity, instead, only suffered a moderate surface deposition, leading to electrical energy savings of 21% and 36% in terms of electrocoagulant delivery and unit log virus reduction, respectively. Neutron computed tomography revealed the critical role of electrode porosity in utilizing the electrode’s internal surface for electrodissolution and effective delivery of electrocoagulant to the bulk. Energy savings of up to 88% in short-term operation were obtained with porous electrodes in a continuous flow-through system. Further investigation on the impact of current density and porosity in long-term operation is desired as well as the capital cost of porous electrodes.

42 ENGINEERING↗
DOE OSTI2024

Re-examination of the Claimed Isolation of Stable Noncyclic 1,2-Disulfoxides

Re-examination of the claimed isolation and X-ray characterization of di-p-tolyl and dimesityl 1,2-disulfoxides from thermolysis of the corresponding aryl sulfinimines and thiosulfinates showed that the isolated disulfide dioxides are instead the wellknown isomeric thiosulfonates, as confirmed by XAS, DART-MS, X-ray, IR and NMR methods. Concerns with the original X-ray structures are addressed. Our results agree with the DFT prediction of very weak diaryl 1,2-disulfoxide S–S bond dissociation enthalpies. For now, room-temperature-stable noncyclic 1,2-disulfoxides remain unknown.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Programmable bionanocomposite coated fertilizers for prolonged controlled release of nitrogen

Controlled-release fertilizers (CRFs) present a promising solution for alleviating food and nutrient scarcity. However, their development has been mainly hindered by both rapid and unsynchronized nutrient release and unsustainable coating materials. In this study, we address this issue by developing a new coating layer for CRFs using a programmable biopolyurethane nanocomposite. This nanocomposite is prepared from diphenylmethane diisocyanate (MDI)-functionalized bentonite nanoclay (BNT-MDI) and a biopolyol from biomass waste. The results show that the BNT-MDI-doped CRFs (BCRFs) exhibit an impressive nitrogen (N)-release longevity of approximately 120 days at a 4 wt% coating ratio, surpassing previous CRF formulations. In a 30-day snap bean cultivation study, BCRF significantly improved root length (1000%), leaf length (257%), leaf width (400%), and plant height (1400%) compared to the control. The superior performance of BCRF is attributed to the PU-nanoclay biocomposite film, with full nano-exfoliation, controllable porosity, and high crosslinking density. Furthermore, we introduce a new dynamic release mechanism and establish a quantitative relationship between the nanostructure, property, and release performance of BCRF by combining the multiplicative and diffusion models for porous materials. Finally, this study provides a theoretical framework and a straightforward methodology for designing programmable nanocomposite structures for future biobased CRFs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Coherent Erbium Spin Defects in Colloidal Nanocrystal Hosts

We demonstrate nearly a microsecond of spin coherence in Er 3+ ions doped in cerium dioxide nanocrystal hosts, despite a large gyromagnetic ratio and nanometric proximity of the spin defect to the nanocrystal surface. The long spin coherence is enabled by reducing the dopant density below the instantaneous diffusion limit in a nuclear spin-free host material, reaching the limit of a single erbium spin defect per nanocrystal. We observe a large Orbach energy in a highly symmetric cubic site, further protecting the coherence in a qubit that would otherwise rapidly decohere. Spatially correlated electron spectroscopy measurements reveal the presence of Ce 3+ at the nanocrystal surface, which likely acts as extraneous paramagnetic spin noise. Even with these factors, defect-embedded nanocrystal hosts show tremendous promise for quantum sensing and quantum communication applications, with multiple avenues, including core-shell fabrication, redox tuning of oxygen vacancies, and organic surfactant modification, available to further enhance their spin coherence and functionality in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Trickier than It Looks: Isomerization between Five- and Six-Coordinated Zinc in Heterometallic Li 2 Zn 2 Molecule

This report describes the synthesis and characterization of two hetero bi metallic Li–Zn coordination isomers [Li 2 Zn 2 (tbaoac) 6 ] (tbaoac = tert -butyl acetoacetato) that have been isolated separately by the same stoichiometric reaction run in different organic solvents. The 6-coordinated zinc isomer ( 6-Zn ) was synthesized in acetone with high yield, while the 5-coordinated one ( 5-Zn ) was readily obtained from ethanol. The 5-Zn isomer has a low solubility in organic solvents such as alkanes and haloalkanes, while its 6-Zn counterpart exhibits a good solubility in almost all common solvents. Two isomeric molecules feature similar centrosymmetric tetranuclear cyclic assemblies, which are different in their arrangement of tbaoac ligands. While all ligands act as μ 2 -type in the structure of 5-Zn , the two tbaoac groups chelating Li appear as μ 3 -type in 6-Zn , thus providing an additional coordination for Zn ions. However, the real structural transformation between these isomers was shown to be more complex than simply making or breaking a couple of Zn–O bonds. X-ray single-crystal structure analysis, powder X-ray diffraction, multinuclear NMR, DART mass spectrometry, ICP-OES analysis, and TGA have been employed for the characterization of the isomers. The combination of powder X-ray diffraction and 1 H NMR investigation revealed that 6-Zn isomer can be quantitatively transformed to 5-Zn in ethanol, while the reverse conversion instantly takes place in acetone.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Hydride-Based Interlayer for Solid-State Anode-Free Battery

Solid-state batteries (SSBs) are considered a promising approach to realizing an anode-free concept with high energy densities. However, the initial Coulombic efficiency (ICE) has remained insufficient for anode-free batteries using sulfide-based solid electrolytes (SEs). Herein, we incorporated a hydride-based interlayer, 3LiBH 4 -LiI (LBHI), between a typical sulfide SE, Li 6 PS 5 Cl, and the Cu current collector. Further, by investigating the Li plating and stripping behaviors and the (electro)chemical stability between SEs and plated Li, we demonstrated that LBHI can effectively improve interfacial stability, leading to an ICE exceeding 94% in anode-free half cells. This interlayer also improves Coulombic efficiencies and specific capacities in anode-free full cells. Furthermore, the utilization of LBHI enables one to study Li plating behaviors without interference from interfacial (electro)chemical instabilities. The analysis of stack pressure evolution during electrochemical cycling reveals that soft shorting in SSBs arises from both dendrite formation and deformation, offering insights into further optimizing solid-state anode-free batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Density Measurements of Molten LiF–BeF 2 and LiF–BeF 2 –LaF 3 Salt Mixtures by Neutron Radiography

The densities of eutectic (LiF) 2 –BeF 2 and mixtures of this salt (FLiBe) with LaF 3 were measured by dilatometry and by neutron attenuation from 673 K to 1,073 K. Because LaF 3 has a limited solubility in FLiBe, it was necessary to determine the amount of LaF 3 in solution before the density could be determined. The FLiBe density determination was favorably benchmarked against the literature data. A simple comparison was not available for the LaF 3 –FLiBe mixtures, so extrapolation of published data was necessary based on analysis using the Molten Salt Thermal Properties Database-Thermochemistry, or MSTDB-TC, developed by the US Department of Energy. Solubilities for LaF 3 in FLiBe ranged from 1 to 4 mol % over 673 to 1,073 K. The salt system was heated and cooled over 24 h to evaluate potential changes in composition and hysteresis during the measurement. Changes in the meniscus were observed, and these were included in the correction for density determinations. Salt surface tension may have led to supersaturation of LaF 3 in the salt because the solubility curve was nonlinear with respect to the inverse temperature, as would be expected for an ideal system. Surface tension measurements are currently underway to test this hypothesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal deflection in neutron scattering sample environments at Oak Ridge National Laboratory

The neutron sources at Oak Ridge National Laboratory use a wide suite of sample environment equipment to deliver extreme conditions for a number of experiments. Much of this instrumentation focuses on extremes of temperature, such as cryostats, closed-cycle refrigerators in both low and high temperature configurations, and radiant heating furnaces. When the temperature is controlled across a large range, thermal deflection effects can notably move the sample and affect its alignment in the beam. Here, we combine these sample environments with neutron imaging and machine vision to determine the motion of a representative sample with respect to the neutron beam. We find vertical sample displacement on the order of 1–2 mm and horizontal displacement that varies from near-negligible to 1.2 mm. While these deflections are not relevant for some of the beamlines at the first target station at the spallation neutron source and the high flux isotope reactor, they will become critical for upcoming instrumentation at the second target station, as well as any instruments targeting sub-mm samples, as neutron sources and optics evolve to smaller and more focused beams. We discuss mitigation protocols and potential modifications to the environment to minimize the effect of misalignment due to thermal deflection.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Anhydrous volatile fatty acid extraction through omniphobic membranes by hydrophobic deep eutectic solvents: Mechanistic understanding and future perspective

Volatile fatty acids (VFAs) derived from arrested anaerobic digestion (AD) can be recovered as a valuable commodity for value-added synthesis. However, separating VFAs from digestate with complex constituents and a high-water content is an energy-prohibitive process. This study developed an innovative technology to overcome this barrier by integrating deep eutectic solvents (DESs) with an omniphobic membrane into a membrane contactor for efficient extraction of anhydrous VFAs with low energy consumption. Here, a kinetic model was developed to elucidate the mechanistic differences between this novel omniphobic membrane-enabled DES extraction and the previous hydrophobic membrane-enabled NaOH extraction. Experimental results and mechanistic modeling suggested that VFA extraction by the DES is a reversible adsorption process facilitating subsequent VFA separation via anhydrous distillation. High vapor pressure of shorter-chain VFAs and low Nernst distribution coefficients of longer-chain VFAs contributed to DES-driven extraction, which could enable continuous and in-situ recovery and conversion of VFAs from AD streams.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Scintillator-based Timepix3 detector for neutron spin-echo techniques using intensity modulation

A scintillator-based Timepix3 (TPX3) detector was developed to resolve the high-frequency modulation of a neutron beam in both spatial and temporal domains, as required for neutron spin-echo experiments. In this system, light from a scintillator is manipulated with an optical lens and is intensified using an image intensifier, making it detectable with the TPX3 chip. Two different scintillators, namely, 6 LiF:ZnS(Ag) and 6 LiI:Eu, were investigated to achieve the high resolution needed for spin-echo modulated small-angle neutron scattering (SEMSANS) and modulation of intensity with zero effort (MIEZE). The methodology for conducting event-mode analysis is described, including the optimization of clustering parameters for both scintillators. The detector with both scintillators was characterized with respect to detection efficiency, spatial resolution, count rate, uniformity, and γ-sensitivity. The 6 LiF:ZnS(Ag) scintillator-based detector achieved a spatial resolution of 200 μm and a count rate capability of 1.1 × 10 5 cps, while the 6 LiI:Eu scintillator-based detector demonstrated a spatial resolution of 250 μm and a count rate capability exceeding 2.9 × 10 5 cps. Furthermore, high-frequency intensity modulations in both spatial and temporal domains were successfully observed, confirming the suitability of this detector for SEMSANS and MIEZE techniques, respectively.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Neutron imaging the spatial progression of chemical oxidation of lithium-ion cathode material in a packed bed reactor

Emerging electrochemical systems relevant to energy applications including redox targeted flow batteries rely on chemical redox of solid electroactive materials using dissolved redox couples. One configuration to facilitate contact between the redox shuttles and solid material which is volume efficient is a packed bed reactor. While methods have been reported to assess the overall progression by analysis of the packed bed reactor effluent, herein analysis of the spatial progression of the chemical redox will be reported. Combination of neutron and x-ray tomography enabled assessing the pore and particle structure in the packed bed reactor and the spatial homogeneity of the reaction at different overall extents of conversion of the reactor bed. Finally, these characterization tools provide methods to probe the chemical redox processes occurring within the reactor environment.

25 ENERGY STORAGE↗
DOE OSTI2023

In operando neutron imaging characterizations of all-solid-state batteries

The surge in electric vehicle demand has propagated the extensive application of lithium-ion batteries (LIBs) in recent years. Gaining significant traction due to their promising high-energy density and elevated safety over traditional LIBs, all-solid-state Li batteries (ASLBs) have nonetheless been faced with hurdles relating to battery performance. These include concerns with interfacial compatibility, structural stability, Li dendrite inhibition, and large-scale manufacturing. To tackle these issues, it is necessary to employ advanced characterization methods to comprehend the intrinsic mechanisms within ASLBs. In this article, we advocate for the use of neutron imaging as a nondestructive approach for the operando visualization of ASLBs. We draw comparisons with other operando visualization strategies, underline the benefits of neutron imaging, and discuss its potential applicability in the scrutiny of all-solid-state Li metal batteries and all-solid-state Li-sulfur batteries. Neutron imaging provides valuable insights into the dynamics of Li concentration, reaction mechanisms, and transport constraints in ASLBs. These insights are pivotal in contributing to the evolution of high-performance all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Measurement of needle and armature dynamics in a gasoline direct injector by high-speed neutron imaging

In modern spark ignition engines, precise delivery of fuel with gasoline direct injection has become increasingly important in the effort to meet ever stricter efficiency and emissions regulations. Use of multiple small close-coupled injections has become more common in attempt to precisely control fuel distribution in the cylinder, but these strategies are hindered by nonlinear injection effects due to operation in the ballistic region of the solenoid-operated valve and due to armature bounce at the end of injection. Understanding the internal dynamics of the injector is crucial to minimizing and controlling non-linearity and shot-to-shot variation, but the experimental techniques available to date are capable only of tracking the position of either the top of the needle (via laser sensors or by monitoring current and voltage in the solenoid coil) or the bottom of the needle (via transparent nozzles or high-speed x-ray imaging). Furthermore, a complete picture of the axial and radial motion of valve needle has until now remained elusive. In this work, we present high-speed ensemble neutron transmission imaging of an entire 8-hole gasoline direct injector operating at 200 bar, allowing for both visualization and quantification of the actuation dynamics including lift and wobble of the valve ball, oscillation and bending of the valve needle, lift, rocking, and bounce of the armature, compression of the springs, and radial swelling of the solenoid during energization. Because neutrons offer high penetration through the metal injector while also being sensitive to the 1 H nuclei in fuel molecules, it is also possible to simultaneously see the fluid dynamics of the injection process, including filling of the sac volume, emanation of the spray through the nozzle holes and into the downstream gas, and the formation and evolution of fuel films on the tip of the injector and the walls of the spray container.

33 ADVANCED PROPULSION SYSTEMS↗