Search NASA⌕ Search

Engineering topics

Zhu, Hongli

Publications and source records attributed to Zhu, Hongli.

28 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Opening twisted polymer chains for simultaneously high printability and battery fast-charge

Fast-charging is key to the widespread adoption of battery-based electric vehicles. However, improving fast-charging through architecture optimization is expensive. To reduce costs and expand to commercialization, we applied roll-to-roll screen printing technology to create channels and decrease the tortuosity of electrodes. For the first time, this work successfully opened twisted polymer chains within high-solid-content inks to improve their screen printability and battery performance of as-printed electrodes. With LiNi 0.6 Mn 0.2 Co 0.2 O 2 as active materials, the 60% solid content ink presents superior screen printability after opening the twisted binder chains. As-printed electrode exhibits 33% higher charge capacity at 6 C than printed electrode with chains twisted ink at mass loading of 6.5 mg/cm 2 . Furthermore, coarse-grained molecular dynamics simulations are performed to study the underlying mechanism systematically. In conclusion, the new ink preparation procedure provides a scalable, effective strategy for manufacturing screen-printable battery ink and promotes screen-printed electrode technology.

25 ENERGY STORAGE↗
DOE OSTI2022

Impact of biomass ash content on biocomposite properties

Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). Furthermore, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0–7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Molecular Engineering of Biorefining Lignin Waste for Solid-State Electrolyte

Lignin is the second most abundant renewable biopolymer on Earth but also a waste in both the paper industry and lignocellulosic biorefineries. Recently, lignin valorization has been extensively sought after to return economics, enhance carbon efficiency, and improve the bioeconomy, but the commercial value and size compatibility still hinder its applications. In this study, we developed a facile strategy to apply lignin waste into a solid-state electrolyte (SSE), which represents a safe next generation energy storage. Here, lignin was grafted with polyethylene glycol (PEG), an efficient lithium-ion (Li + ) conductive polymer, to enable its ion conduction. The synthesized PEG-g-lignin was mixed with poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) and PEG-g-lignin-based bis(trifluoromethanesulfonyl)imide (LiTFSI) to prepare a solid polymer electrolyte (SPE), which has an ionic conductivity of 2.5 × 10 –5 S/cm at 25 °C. This result was further enhanced to 6.5 × 10 –5 S/cm by adding an ion-conductive ceramic of Li 6.4 La 3 Ga 0.2 Zr 2 O 12 (LLGZO), which is referred to as composite polymer electrolyte (CPE). These data represent the highest ones among reported polymer-based SSE. A mechanistic study by using 2D HSQC NMR revealed that PEG-g-lignin has increased ether type β–O–4 linkages that can promote the interchain hopping of Li+ between lignin polymer chains, and 31 P NMR revealed that the lignin phenolic end can be associated by Li + . Moreover, the abundant aromatic moieties and methoxyl in PEG-g-lignin also enhanced Li + association and improved its ionic conductivity. The superior ionic conductivity of PEG-g-lignin-based SSE can enable massive applications of this biorefining waste in all-solid-state lithium batteries (ASSLBs), which has potential to promote the energy sector by promoting the bioeconomy and enhancing the renewability and sustainability of future energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Turning Natural Herbaceous Fibers into Advanced Materials for Sustainability

Considering the growing concerns about natural resource depletion, energy inequality, and climate crises, biomass-derived materials—the most abundant organic matter on the planet—have received a lot of attention as a potential alternative to petroleum-based plastics. Herbaceous biomasses and extracted cellulose have recently been extensively used in the development of high-performance and multifunctional materials. Herbaceous biomass has sparked interest due to its species diversity, abundance, low cost, lightweight, and sustainability. This review discusses the structure versus property relationships of various sources of herbaceous biomasses (e.g., sugarcane, straw, and bamboo) and their extracted biomaterials, as well as the latest emerging applications from macro- and microscales to nanoscales. We report, high-strength structural materials, porous carbon materials, multichannel materials, and flexible materials are examples of these applications, which include sustainable electronics, environmentally friendly energy harvesting, smart materials, and biodegradable structural buildings.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Long–Cycling Sulfide–Based All–Solid–State Batteries Enabled by Electrochemo–Mechanically Stable Electrodes

Anode significantly determines the energy density of all-solid-state Lithium batteries (ASLBs). Silicon (Si) and Lithium (Li) metal are two of the most attractive anodes because of their ultrahigh theoretical capacities. However, most investigations focus on Li metal; the great potential of Si is underrated. This study investigates Si anode's stability, processability, and cost in ASLBs and compares them with Li metal. Moreover, the single-crystal LiNi 0.8 Co 0.1 Mn 0.1 O 2 is stabilized with a lithium silicate (Li 2 SiO x ) through a scalable sol-gel method. ASLBs with a cell-level energy density of 285 Wh kg -1 are obtained through sandwiching Si anode, thin sulfide solid-state electrolyte membrane, and interface stabilized LiNi 0.8 Co 0.1 Mn 0.1 O 2 . The full cell delivered a high capacity of 145 mAh g -1 at C/3 and maintained stability for 1000 cycles. This work inspires commercializing the ASLBs on a large scale with exciting manufacturing lines for large-scale, safe, and economical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2021

Recycling of natural fiber composites: Challenges and opportunities

Natural fibers have been widely used for reinforcing polymers attributed to their sustainable nature, excellent stiffness to weight ratio, biodegradability, and low cost compared with synthetic fibers like carbon or glass fibers. Thermoplastic composites offer an advantage of recyclability after their service life, but challenges and opportunities remain in the recycling of natural fiber reinforced polymer composites (NFRPCs). This article summarized the effects of reprocessing/recycling on the material properties of NFRPCs. The material properties considered include mechanical performance, thermal properties, hygroscopic behavior, viscoelasticity, degradation, and durability. NFRPCs can generally be recycled approximately 4–6 times until their thermomechanical properties change. After recycling 7 times, the tensile strength of NFRPCs can decrease by 17%, and the tensile modulus can decrease by 28%. The mitigation approaches to overcome degradation of material properties of NFRPCs such as adding functional additives and virgin plastics are also discussed. The main challenges in these approaches such as degradation and incompatibility are discussed, and an effort is made to provide a rationale for reprocessing/recyclability assessment. Finally, future applications of NFRPCs such as additive manufacturing and automotive part use are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5–1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Therefore, based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li 6 PS 5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm -2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg -1 and 675 Wh L -1 , individually.

25 ENERGY STORAGE↗
DOE OSTI2021

Self-Stabilized LiNi 0.8 Mn 0.1 Co 0.1 O 2 in thiophosphate-based all-solid-state batteries through extra LiOH

Nickle-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC 811) cathode material exhibits engaging properties in high energy density and low cost, making it great potential for the next generation high-energy all-solid-state lithium batteries (ASSLBs). However, NMC 811 suffers from severe surface electrochemical, chemical, and voltage incompatibility towards solid-state electrolytes (SSE), especially thiophosphate-based electrolytes like Li 6 PS 5 Cl. Although diverse coating methods have been made to overcome this issue, they are typically cumbersome and expensive. A coating strategy that satisfied all the requirements of cost-efficiency, stability, uniformity, scalability, and easy-achieving is still challenging. Here, we developed a LiOH-based surface stabilization strategy that provides a ~10 nm stable permeable layer on NMC 811. After one-step sintering of NMC 811 precursor mixed with LiOH, which is commonly used for NMC 811 lithiation process, excessive LiOH simultaneously distributes on NMC 811 particles. Unlike other reported methods, this coating method can be easily controlled and fabricated without additional complicated processes. By simply controlling the thickness of LiOH layer, which protects the Li 6 PS 5 Cl solid electrolyte materials from being oxidized, optimized cycling stability can be obtained for 600 cycles with capacity of 130 mAh g – 1 on average at a wide electrochemical window of 2.50–4.20 V (vs. Li-In).

25 ENERGY STORAGE↗
DOE OSTI2020

Regulated lithium ionic flux through well-aligned channels for lithium dendrite inhibition in solid-state batteries

The utilization of solid electrolyte (SE) to suppress lithium (Li) dendrites is promising but still far from satisfactory due to the inhomogeneous Li plating/stripping. In this paper, we demonstrated a novel strategy to inhibit Li dendrites via regulating Li-ion flux in SE by using vertically aligned channels. The ion-insulating walls facilitated uniform distribution of Li-ion flux through the channels, leading to a homogeneous Li deposition, thus alleviating Li dendrite formation. As a result, symmetric cells with this SE exhibited excellent long-term stability (1000 h) against Li metal. In addition, Li4Ti5O12 (LTO)/Li cell with the developed SE achieved good battery performance over 100 cycles. The mechanism for dendrite suppression was further investigated by phase-field simulation. This work provides a novel strategy by manipulating uniform Li-ion flux to fabricate SE to inhibit Li dendrites and facilitates the development of high-performance rechargeable Li batteries.

25 ENERGY STORAGE↗