Search NASA⌕ Search

Engineering topics

Zhu, Hongli

Publications and source records attributed to Zhu, Hongli.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Metal–Organic Framework-derived Atomic Metal Sites Promoting Sulfur Cathode for All-Solid-State Lithium–Sulfur Batteries

All-solid-state lithium–sulfur batteries (ASSLSBs) offer high energy density and intrinsic safety; however, they still face major challenges, including sluggish redox kinetics and poor sulfur utilization. Incorporating conductive materials into sulfur cathodes is an effective strategy to mitigate these limitations. Here, a highly conductive cobalt–nitrogen–doped carbon (Co–NC) derived from a metal–organic framework (MOF) is introduced to accelerate charge transfer and promote reversible sulfur conversion. Co−NC provides atomically dispersed Co–N sites and conductive carbon pathways that correlate with improved charge transfer, sulfur utilization, and rate capability. Co–NC@S cathode delivers 1499 mAh g–1 at C/20 with a high sulfur loading (5 mg cm–2) and retains 1292 mAh g–1 after five cycles (vs 443 mAh g–1 without Co–NC). Moreover, Co–NC derived ASSLSB achieves 903 mAh g–1 at 5C at 60 °C. This work provides a practical and effective approach to develop high energy, high-rate ASSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Stabilizing Nickel‐Rich Cathodes in Aqueous Process through Nanocellulose as Water Barrier

Nickel-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC 811) cathode offers high voltage and high specific capacity, making it promising for high energy density batteries. However, large-scale manufacturing of aqueous-processed NMC 811 electrodes remains challenging due to proton exchange causing material decomposition and capacity loss. This work addresses this issue by constructing an in situ nanocellulose protective layer for NMC 811 particles via electrostatic interactions during the slurry preparation. For the first time, the interatomic spacing between inter-chains of nanocellulose is measured through wide-angle X-ray scattering and demonstrate the ability to effectively confine interlayer water using atomistic simulations. Moreover, this nanocellulose coverage simultaneously minimizes Li + surface segregation and mitigates water infiltration. Owing to less material decomposition during the aqueous processing, nanocellulose-protected NMC electrodes exhibit higher initial coulombic efficiency (83% vs 62% at 0.1C) and capacity (133 vs 59 mAh g −1 at 6C) than unprotected electrodes. Additionally, optimized aqueous-processed NMC electrodes offer comparable or even superior electrochemical properties compared to the electrodes fabricated using the conventional toxic organic solvent, N-methyl-2-pyrrolidone. Consequently, the developed approach enables affordable, sustainable aqueous processing for Nickel-rich NMC 811 cathodes with excellent electrochemical performances.

25 ENERGY STORAGE↗
DOE OSTI2024

Promoting electrochemical rates by concurrent ionic-electronic conductivity enhancement in high mass loading cathode electrode

Enhancing the fast charging capacity of thick electrodes with high mass loading is imperative in expediting the widespread adoption of electric vehicles. Nonetheless, the insufficient charge transfer kinetics of thick electrodes hinder the movement of effective electrons and ions, hence diminishing capacity at high current rates. In this work, we applied sustainable and biodegradable cellulose nanocrystals (CNCs) as electrode additives. It is the first time to simultaneously improve the electronic conductivity by optimizing the carbon dispersion and establishing electron transfer networks, as well as boosting the ionic conductivity of electrodes by shortening the ion transfer pathway. Specifically, the LiNi 0.6 Mn 0.2 Co 0.2 O 2 electrodes incorporating 1% dual functional CNCs additive exhibit improved effective electrical conductivity from 0.11 to 0.16 S/m and risen effective ionic conductivity from 0.36 to 0.62 S/m, in comparison to counterpart electrodes without CNCs. Therefore, the 1% CNC electrode with a high mass loading of 27.0 mg/cm 2 delivers a discharge capacity of 128 mAh/g at 1 C, which is superior to that of the CNC-free electrodes (95 mAh/g). In short, this study presents a novel environmentally friendly, economically viable, and dual-functional electrode additive that enhances both electronic and ionic conductivities with the aim of facilitating the widespread adoption of fast-charging high mass loading electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Detection of a Cobalt-Containing Interphase at the Li 6 PS 5 Cl-NMC111 Interface by In Situ μ XANES and EIS

Sulfide electrolyte all-solid-state lithium batteries (ASLBs) with uncoated Li-Ni x Mn y Co 1–x–y O 2 (NMC) cathodes suffer from a large capacity loss during initial cycling and an increase in cell impedance. Decomposition reactions are known to occur at the Li 6 PS 5 Cl-NMC111 interface due to incompatibility between the two materials. If a stabilizing coating is applied to the NMC, it delivers full capacity during initial charge. However, the loss in capacity during discharge still occurs. The interface was studied by μ XANES and through EIS analysis. A chemically-formed interphase was detected by μ XANES, evident from reduction of Co at an uncoated NMC particle surface. This interphase was produced by decomposition at rest. To study the effect of the interphase on electrochemically active surface area, piecewise in situ EIS was performed and the data was modeled using a transmission line model (TLM). The charge transfer resistance R CT was used to estimate the volume specific active surface area (a act ). The median value for a act was 296 cm –1 , a factor of 7.5 lower than the theoretical value of 2216 cm –1 . This provided evidence of a lower electrochemically active surface area in the ASLB.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advances in solid-state batteries: Materials, interfaces, characterizations, and devices

Solid-state batteries with features of high potential for high energy density and improved safety have gained considerable attention and witnessed fast growing interests in the past decade. Significant progress and numerous efforts have been made on materials discovery, interface characterizations, and device fabrication. Further, this issue of MRS Bulletin focuses on the current state of the art of solid-state batteries with the most important topics related to the interface issues, advanced characterizations, and electrode chemistries, aiming to provide a comprehensive perspective for the interface and characterization challenges for high-performance solid-state battery devices.

25 ENERGY STORAGE↗
DOE OSTI2023

In operando neutron imaging characterizations of all-solid-state batteries

The surge in electric vehicle demand has propagated the extensive application of lithium-ion batteries (LIBs) in recent years. Gaining significant traction due to their promising high-energy density and elevated safety over traditional LIBs, all-solid-state Li batteries (ASLBs) have nonetheless been faced with hurdles relating to battery performance. These include concerns with interfacial compatibility, structural stability, Li dendrite inhibition, and large-scale manufacturing. To tackle these issues, it is necessary to employ advanced characterization methods to comprehend the intrinsic mechanisms within ASLBs. In this article, we advocate for the use of neutron imaging as a nondestructive approach for the operando visualization of ASLBs. We draw comparisons with other operando visualization strategies, underline the benefits of neutron imaging, and discuss its potential applicability in the scrutiny of all-solid-state Li metal batteries and all-solid-state Li-sulfur batteries. Neutron imaging provides valuable insights into the dynamics of Li concentration, reaction mechanisms, and transport constraints in ASLBs. These insights are pivotal in contributing to the evolution of high-performance all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Nondestructively Visualizing and Understanding the Mechano-Electro-chemical Origins of “Soft Short” and “Creeping” in All-Solid-State Batteries

All-solid-state Li-metal batteries (ASLMBs) represent a significant breakthrough in the quest to overcome limitations associated with traditional Li-ion batteries, particularly in energy density and safety aspects. However, widespread implementation is stymied due to a lack of profound understanding of the complex mechano-electro-chemical behavior of Li metal in the ASLMBs. Herein, operando neutron imaging and X-ray computed tomography (XCT) are leveraged to nondestructively visualize Li behaviors within ASLMBs. This approach offers real-time observations of Li evolutions, both pre- and post- occurrence of a “soft short”. The coordination of 2D neutron radiography and 3D neutron tomography enables charting of the terrain of Li metal deformation operando. Concurrently, XCT offers a 3D insight into the internal structure of the battery following a “soft short”. Despite the manifestation of a “soft short”, the persistence of Faradaic processes is observed. To study the elusive “soft short”, phase field modeling is coupled with electrochemistry and solid mechanics theory. The research unravels how external pressure curbs dendrite growth, potentially leading to dendrite fractures and thus uncovering the origins of both “soft” and “hard” shorts in ASLMBs. Furthermore, by harnessing finite element modeling, it dive deeper into the mechanical deformation and the fluidity of Li metal.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding Electrochemical Reaction Mechanisms of Sulfur in All‐Solid‐State Batteries through Operando and Theoretical Studies **

Abstract Due to its outstanding safety and high energy density, all‐solid‐state lithium‐sulfur batteries (ASLSBs) are considered as a potential future energy storage technology. The electrochemical reaction pathway in ASLSBs with inorganic solid‐state electrolytes is different from Li‐S batteries with liquid electrolytes, but the mechanism remains unclear. By combining operando Raman spectroscopy and ex situ X‐ray absorption spectroscopy, we investigated the reaction mechanism of sulfur (S 8 ) in ASLSBs. Our results revealed that no Li 2 S 8, Li 2 S 6, and Li 2 S 4 were formed, yet Li 2 S 2 was detected. Furthermore, first‐principles structural calculations were employed to disclose the formation energy of solid state Li 2 S n (1≤ n ≤8), in which Li 2 S 2 was a metastable phase, consistent with experimental observations. Meanwhile, partial S 8 and Li 2 S 2 remained at the full lithiation stage, suggesting incomplete reaction due to sluggish reaction kinetics in ASLSBs.

Cao, Daxian↗
DOE OSTI2023

Understanding Electrochemical Reaction Mechanisms of Sulfur in All‐Solid‐State Batteries through Operando and Theoretical Studies **

Abstract Due to its outstanding safety and high energy density, all‐solid‐state lithium‐sulfur batteries (ASLSBs) are considered as a potential future energy storage technology. The electrochemical reaction pathway in ASLSBs with inorganic solid‐state electrolytes is different from Li‐S batteries with liquid electrolytes, but the mechanism remains unclear. By combining operando Raman spectroscopy and ex situ X‐ray absorption spectroscopy, we investigated the reaction mechanism of sulfur (S 8 ) in ASLSBs. Our results revealed that no Li 2 S 8, Li 2 S 6, and Li 2 S 4 were formed, yet Li 2 S 2 was detected. Furthermore, first‐principles structural calculations were employed to disclose the formation energy of solid state Li 2 S n (1≤ n ≤8), in which Li 2 S 2 was a metastable phase, consistent with experimental observations. Meanwhile, partial S 8 and Li 2 S 2 remained at the full lithiation stage, suggesting incomplete reaction due to sluggish reaction kinetics in ASLSBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Designing Low Tortuosity Electrodes through Pattern Optimization for Fast-Charging

The development of fast-charging technologies is crucial for expediting the progress and promotion of electric vehicles. In addition to innovative material exploration, reduction in the tortuosity of electrodes is a favored strategy to enhance the fast-charging capability of lithium-ion batteries by optimizing the ion-transfer kinetics. To realize the industrialization of low-tortuosity electrodes, a facile, cost-effective, highly controlled, and high-output continuous additive manufacturing roll-to-roll screen printing technology is proposed to render customized vertical channels within electrodes. Extremely precise vertical channels are fabricated by applying the as-developed inks, using LiNi 0.6 Mn 0.2 Co 0.2 O 2 as the cathode material. Additionally, the relationship between the electrochemical properties and architecture of the channels, including the pattern, channel diameter, and edge distance between channels, is revealed. The optimized screen-printed electrode exhibited a seven-fold higher charge capacity (72 mAh g -1 ) at a current rate of 6 C and superior stability compared with that of the conventional bar-coated electrode (10 mAh g -1 , 6 C) at a mass loading of 10 mg cm -2 . Finally, this roll-to-roll additive manufacturing can potentially be applied to various active materials printing to reduce electrode tortuosity and enable fast charging in battery manufacturing.

42 ENGINEERING↗
DOE OSTI2023

Unveiling the Mechanical and Electrochemical Evolution of Nanosilicon Composite Anodes in Sulfide-Based All-Solid-State Batteries

The utilization of silicon anodes in all-solid-state lithium batteries provides good prospects for facilitating high energy density. However, the compatibility of sulfide solid-state electrolytes (SEs) with Si and carbon is often questioned due to potential decomposition. Here, in this paper, operando X-ray absorption near-edge structure (XANES) spectroscopy, ex situ scanning electron microscopy (SEM), and ex situ X-ray nanotomography (XnT) are utilized to investigate the chemistry and structure evolution of nano-Si composite anodes. Results from XANES demonstrate a partial decomposition of SEs during the first lithiation stage, which is intensified by the presence of carbon. Nevertheless, the performances of first three cycles in Si–SE–C are stable, which proves that the generated media is ionically conductive. XnT and SEM results show that the addition of SEs and carbon improves the structural stability of the anode, with fewer pores and voids. A chemo-elasto-plastic model reveals that SEs and carbon buffer the volume expansion of Si, thus enhancing mechanical stability. The balance between the pros and cons of SEs and carbon in enhancing reaction kinetics and structural stability enables the Si composite anode to demonstrate the highest Si utilization with higher specific capacities and a better rate than pure Si and Si composite anodes with only SEs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manufacturing Water‐Based Low‐Tortuosity Electrodes for Fast‐Charge through Pattern Integrated Stamping

Achieving high energy density and fast charging of lithium‐ion batteries can accelerate the promotion of electric vehicles. However, the increased mass loading causes poor charge transfer, impedes the electrochemical reaction kinetics, and limits the battery charging rate. Herein, this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode, which benefits ion transport and increases the rate performance of the electrode. Meanwhile, the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode. Compared to the conventional bar‐coated electrode with the same thickness of 155 μm (delivered a discharge capacity of 16 mAh g −1 at the rate of 3 C), the stamped low‐tortuosity LiFePO 4 electrode delivered 101 mAh g −1 capacity. Additionally, water was employed as a solvent in this study. Owing to its eco‐friendliness, high scalability, and minimal waste generation, this novel stamping technique inspire a new method for the industrial‐level efficient roll to roll fabrication of fast‐charge electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Lithiation Gradients and Tortuosity Factors in Thick NMC111-Argyrodite Solid-State Cathodes

Achieving high energy density in all-solid-state lithium batteries will require the design of thick cathodes, and these will need to operate reversibly under normal use conditions. We use high-energy depth-profiling X-ray diffraction to measure the localized lithium content of Li 1-x Ni 1/3 Mn 1/3 Co 1/3 O 2 (NMC111) through the thickness of 110 μm thick composite cathodes. The composite cathodes consisted of NMC111 of varying mass loadings mixed with argyrodite solid electrolyte Li 6 PS 5 Cl (LPSC). During cycling at C/10, substantial lithiation gradients developed, and varying the NMC111 loading altered the nature of these gradients. Microstructural analysis and cathode modeling showed this was due to high tortuosities in the cathodes. This was particularly true in the solid electrolyte phase, which experienced a marked increase in tortuosity factor during the initial charge. Our results demonstrate that current distributions are observed in sulfide-based composites and that these will be an important consideration for practical design of all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Sustainable bioplastics derived from renewable natural resources for food packaging

Food packaging is one of the leading sectors for the end use of plastics. Bioplastic is produced from natural renewable resources such as crops, wood pulp, and herbaceous fibers. This article summarizes the rational design of bioplastics from natural resources for food packaging. The bioplastic properties considered include thermal properties, mechanical performance, oxygen/moisture resistance, and biodegradability. Bioplastic degradability and technologies for handling bioplastic waste are discussed. Various aspects of the sustainability of bioplastics (e.g., environmental profile, techno-economic analysis, and societal impact) are investigated. The main challenges of bioplastic application, such as low fracture strain and inferior barrier properties, are discussed. Mitigation approaches to overcome the mechanical properties of bioplastics, such as adding plasticizers, are also discussed. Bioplastic can have properties comparable with fossil-based plastics. In conclusion, bioplastic can be an alternative to conventional plastic in most applications of food packaging, which can reduce the carbon footprint and environmental impact because of its biodegradability.

09 BIOMASS FUELS↗
DOE OSTI2023

High Ion Conductive and Selective Membrane Achieved through Dual Ion Conducting Mechanisms

Conventional ion-selective membranes, that is ion-exchange and porous membranes, are unable to perform high conductivity and selectivity simultaneously due to the contradictions between their ion selecting and conducting mechanisms. Here, in this work, a bifunctional ion-selective layer is developed via the combination of nanoporous boron nitride (PBN) and ion exchange groups from Nafion to achieve high ion conductivity through dual ion conducting mechanisms as well as high ion selectivity. A template-free method is adopted to synthesize flake-like PBN, which is further enmeshed with Nafion resin to form the bifunctional layer coated onto a porous polyetherimide membrane. The double-layer membrane exhibits excellent ion selectivity (1.49 × 10 8 mS cm –3 min), which is 22 times greater than that of the pristine porous polyetherimide membrane, with outstanding ion conductivity (64 mS cm –1 ). In a vanadium flow battery, the double-layer membrane achieves a high Coulombic efficiency of 97% and outstanding energy efficiency of 91% at 40 mA cm –2 with a stable cycling performance for over 700 cycles at 100 mA cm –2 . PBN with ion exchange groups may therefore offer a potential solution to the limitation between ion selectivity and conductivity in ion-selective membranes.

36 MATERIALS SCIENCE↗