Search NASA⌕ Search

Engineering topics

Zhu, Y.

Publications and source records attributed to Zhu, Y..

At least 19 records

Density fluctuation statistics and turbulence spreading at the edge of L–mode plasmas

Long-wavelength density fluctuations ($k{\rho _i}$ <1) are studied using beam emission spectroscopy (BES) at the edge of DIII-D L-mode plasmas (ρ = 0.88–1.1) in scenarios with electron cyclotron heating (ECH) power ramp (P ECH up to 1.5 MW), neutral beam injection (NBI) power ramp (P NBI up to 2.5 MW), and injected torque scan (-1 < T inj <0.6 Nm). We find that broadband turbulent density fluctuations (ƒ ~ 20–120 kHz) have a non-Gaussian distribution. The skewness of $\delta n/n$ changes sign from negative at ρ < 0.95–0.97 to positive at ρ > 0.97, indicating the prevalence of density 'voids' at inner radii and density 'blobs' at outer radii and outside of the separatrix. The turbulence intensity flux $\left\langle {{{\tilde v}_{\text{r}}}{{\tilde n}^2}} \right\rangle$ is calculated to characterize turbulence spreading at the plasma edge. During ECH/NBI power ramps and at counter-I p injected torque, $\left\langle {{{\tilde v}_{\text{r}}}{{\tilde n}^2}} \right\rangle$ is directed inward inside the separatrix, which is evidence of inward spreading of turbulence intensity from the edge gradient region caused by the inner propagation of density 'voids'. Significantly weaker $\left\langle {{{\tilde v}_{\text{r}}}{{\tilde n}^2}} \right\rangle$ is observed with co-I p torque. A correlation between co-I p torque, turbulence intensity $\delta n/n$ at ρ = 0.97, and increased srape-off layer (SOL) heat flux decay length ${\lambda _q}$ is found in the torque scan scenario, showing that edge turbulence plays a material role in determining the SOL conditions and heat flux width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a liquid-helium free cryogenic sample holder with mK temperature control for autonomous electron microscopy

The automated and autonomous cryogenic transmission electron microscopy (Cryo-EM) demands a sample holder capable of maintaining temperatures below 10 K with precise control, long holding times, and minimal helium use. Rising to this challenge, we initiated an ambitious project to develop a novel closed-cycle cryocooler-based cryogenic sample holder that operates without the use of liquid helium and the consumption of gaseous helium. Here, this article presents the design, construction, and experimental testing of the initial prototype, which achieves an ultimate temperature of 5.6 K with exceptional stability close to 1mK, while providing a wide temperature control range from 295 K to 5.6 K, marking a clear advancement in cryo-EM holder development. While the prototype was not designed for atomic resolution imaging and thus lacks a sturdy support system to mitigate mechanical vibrations from the cryocooler's pulsed tube, this innovative approach successfully demonstrates proof of concept. It offers unprecedented capabilities for state-of-the-art cryogenic microscopy and microanalysis in materials and biological sciences.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Isotope impact on Alfvén eigenmodes and fast ion transport in DIII-D

Abstract Measurements of beam driven Alfvén Eigenmode (AE) activity in matched deuterium (D) and hydrogen (H) DIII-D plasmas show a dramatic difference in unstable mode activity and fast ion transport for a given injected beam power. The dependence of the unstable AE spectrum in reversed magnetic shear plasmas on beam and thermal species is investigated in the current ramp by varying beam power in a sequence of discharges for fixed thermal and beam species at fixed density. In general, a spectrum of Reversed Shear Alfvén Eigenmodes (RSAEs) and Toroidal Alfvén Eigenmodes (TAEs) are driven unstable with sub-Alfvénic D beam injection while primarily only RSAEs are driven unstable for the H beam cases investigated. Further, for a given beam power, the driven AE amplitude is always reduced with H beams relative to D and for H thermal plasma relative to pure D or mixed D/H plasmas. Estimates of the fast ion stored energy combined with modeling using the hybrid kinetic-MHD code MEGA indicate that the dominant mechanism contributing to the difference between H and D beam drive is the faster classical slowing down of H beam ions relative to D and the resultant lower beam ion pressure. Calculations of the AE induced stored energy deficits using the reduced critical gradient model TGLFEP show quantitative agreement with the observed dependencies on injected power, isotope and minimum safety factor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Relation between sampling, sensitivity and precision in strain mapping using the Geometric Phase Analysis method in Scanning Transmission Electron Microscopy

The sensitivity and the precision of the Geometric Phase Analysis (GPA) method for strain characterization is a topic widely discussed in the literature and is usually difficult to quantify. Indeed, the GPA precision is intricately linked to the resolution of the strain maps defined when masking the periodic reflections in Fourier space. In this study an additional parameter, sampling, is proposed to be analyzed regarding the precision of GPA by developing the concept of a phase noise in the GPA equations. Both experimentally and theoretically, the following article demonstrates how the precision, and the sensitivity of the GPA method is improved when using a larger pixel spacing to record an electron micrograph in Scanning Transmission Electron Microscopy (STEM). In conclusion, the counterintuitive concept of increasing the field of view to improve the GPA precision results in an extension of the application of strain characterization methods in STEM towards low deformation levels.

47 OTHER INSTRUMENTATION↗

Vanishing RKKY interactions in Ce-based cage compounds

Abstract We report the results of thermodynamic measurements in external magnetic field of the cubic Ce-based cage compounds Ce T 2 Cd 20 ( T = Ni,Pd). Our analysis of the heat-capacity data shows that the Γ 7 doublet is the ground state multiplet of the Ce 3+ ions. Consequently, for the Γ 7 doublet it can be theoretically shown that the Ruderman–Kittel–Kasuya–Yosida interaction between the localized Ce moments mediated by the conduction electrons, must vanish at temperatures much lower than the energy separating the ground state doublet from the first excited Γ 8 quartet. Our findings provide an insight as to why no long range order has been observed in these compounds down to temperatures in the milliKelvin range.

Physics↗

Cross-platform comparison of arbitrary quantum states

As we approach the era of quantum advantage, when quantum computers (QCs) can outperform any classical computer on particular tasks, there remains the difficult challenge of how to validate their performance. While algorithmic success can be easily verified in some instances such as number factoring or oracular algorithms, these approaches only provide pass/fail information of executing specific tasks for a single QC. On the other hand, a comparison between different QCs preparing nominally the same arbitrary circuit provides an insight for generic validation: a quantum computation is only as valid as the agreement between the results produced on different QCs. Such an approach is also at the heart of evaluating metrological standards such as disparate atomic clocks. In this paper, we report a cross-platform QC comparison using randomized and correlated measurements that results in a wealth of information on the QC systems. We execute several quantum circuits on widely different physical QC platforms and analyze the cross-platform state fidelities.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

System-on-chip approach microwave imaging reflectometer on DIII-D tokamak

System-on-chip millimeter wave integrated circuit technology is used on the two-dimensional millimeter-wave imaging reflectometer (MIR) upgrade for density fluctuation imaging on the DIII-D tokamak fusion plasma. Customized CMOS chips have been successfully developed for the transmitter module and receiver module array, covering the 55–75 GHz working band. The transmitter module has the capability of simultaneously launching eight tunable probe frequencies (>0 dBm output power each). The receiver enclosure contains 12 receiver modules in two vertical lines. The quasi-optical local oscillator coupling of previous MIR systems has been replaced with an internal active frequency multiplier chain for improved local oscillator power delivery and flexible installation in a narrow space together with improved shielding against electromagnetic interference. The 55–75 GHz low noise amplifier, used between the receiver antenna and the first-stage mixer, significantly improves module sensitivity and suppresses electronics noise. The receiver module has a 20 dB gain improvement compared with the mini-lens approach and better than –75 dBm sensitivity, and its electronics noise temperature has been reduced from 55 000 K down to 11 200 K. Further, the V-band MIR system is developed for co-located multi-field investigation of MHD-scale fluctuations in the pedestal region with W-band electron cyclotron emission imaging on DIII-D tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pitting Corrosion in 316L Stainless Steel Fabricated by Laser Powder Bed Fusion Additive Manufacturing: A Review and Perspective

Abstract 316L stainless steel (316L SS) is a flagship material for structural applications in corrosive environments, having been extensively studied for decades for its favorable balance between mechanical and corrosion properties. More recently, 316L SS has also proven to have excellent printability when parts are produced with additive manufacturing techniques, notably laser powder bed fusion (LPBF). Because of the harsh thermo-mechanical cycles experienced during rapid solidification and cooling, LPBF processing tends to generate unique microstructures. Strong heterogeneities can be found inside grains, including trapped elements, nano-inclusions, and a high density of dislocations that form the so-called cellular structure. Interestingly, LPBF 316L SS not only exhibits better mechanical properties than its conventionally processed counterpart, but it also usually offers much higher resistance to pitting in chloride solutions. Unfortunately, the complexity of the LPBF microstructures, in addition to process-induced defects, such as porosity and surface roughness, have slowed progress toward linking specific microstructural features to corrosion susceptibility and complicated the development of calibrated simulations of pitting phenomena. The first part of this article is dedicated to an in-depth review of the microstructures found in LPBF 316L SS and their potential effects on the corrosion properties, with an emphasis on pitting resistance. The second part offers a perspective of some relevant modeling techniques available to simulate the corrosion of LPBF 316L SS, including current challenges that should be overcome.

Voisin, T. (ORCID:0000000287462659)↗

A poloidal high- k scattering system for NSTX-U

A previous 5-channel tangential high-k scattering system is being replaced by an 8-channel, poloidal high-k scattering system on the National Spherical Torus eXperiment Upgrade (NSTX-U) device located in Princeton, NJ, USA. The 693 GHz poloidal scattering system replaces a 280 GHz tangential scattering system to study high-k electron density fluctuations on NSTX-U, thereby considerably enhancing planned turbulence physics studies by providing a measurement of the k θ -spectrum of both electron temperature gradient (ETG) and ion temperature gradient (ITG) modes. Two approaches to generating the 693 GHz probe beam are under development: an optically-pumped far-infrared (FIR) laser that generates ~50 mW, and a compact gyrotron that can potentially generate in excess of 5 W. Large aperture optics collect radiation scattered from density fluctuations in the plasma core at 8 simultaneous scattering angles ranging from 2 to 15° corresponding to poloidal wavenumbers that extend to >40 cm -1 . Finally, steerable launch optics coupled with receiver optics mounted on a 5-axis receiver carriage allow the scattering volume to be placed radially from r/a = 0.3 out to the pedestal region (r/a ~ 0.99) and translated horizontally as needed to satisfy wavenumber matching.

47 OTHER INSTRUMENTATION↗

Josephson detection of time-reversal symmetry broken superconductivity in SnTe nanowires

A Josephson junction (JJ) couples the supercurrent flowing between two weakly linked superconductors to the phase difference between them via a current-phase relation (CPR). While a sinusoidal CPR is expected for conventional junctions with insulating weak links, devices made from some exotic materials may give rise to unconventional CPRs and unusual Josephson effects. In this work, we present such a case: we investigate the proximity-induced superconductivity in SnTe nanowires by incorporating them as weak links in JJs and observe a deviation from the standard CPR. We report on indications of an unexpected breaking of time-reversal symmetry in these devices, detailing the unconventional characteristics that reveal this behavior. These include an asymmetric critical current in the DC Josephson effect, a prominent second harmonic in the AC Josephson effect, and a magnetic diffraction pattern with a minimum in critical current at zero magnetic field. The analysis examines how multiband effects and the experimentally visualized ferroelectric domain walls give rise to this behavior, giving insight into the Josephson effect in materials that possess ferroelectricity and/or multiband superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation of dislocations via misfit strain across interfaces in epitaxial BaTiO 3 and SrIrO 3 heterostructures

Abstract Dislocations often occur in thin films with large misfit strain as a result of strain energy accumulation and can drastically change the film properties. Here the structure and dislocations in oxide heterostructures with large misfit strain are investigated on atomic scale. When grown on SrTiO 3 (001), the dislocations in both the monolithic BaTiO 3 thin film and its superlattices with SrIrO 3 appear above a critical thickness around 6 nm. The edge component of the dislocations is seen in both cases with the Burgers vector of a ⟨100⟩. However, compared to monolithic BaTiO 3 , the dislocation density is slightly lower in BaTiO 3 /SrIrO 3 superlattices. In the superlattice, when considering the SrTiO 3 lattice constant as the reference, BaTiO 3 has a larger misfit strain comparing with SrIrO 3 . It is found that in both cases, the formation of dislocation is only affected by the critical thickness of the film with larger lattice misfit (BaTiO 3 ), regardless of the existence of a strong octahedral tilt/rotation mismatch at BaTiO 3 /SrIrO 3 interface. Our findings suggest that it is possible to control the position of dislocations, an important step toward defect engineering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗