Search NASA⌕ Search
Home/Archive/NASA NTRS

NASA NTRS · 20160001689

Hardness and Microstructure of Binary and Ternary Nitinol Compounds

Stanford, Malcolm K.
View original source ↗Export metadata ↓

Abstract

The hardness and microstructure of twenty-six binary and ternary Nitinol (nickel titanium, nickel titanium hafnium, nickel titanium zirconium and nickel titanium tantalum) compounds were studied. A small (50g) ingot of each compound was produced by vacuum arc remelting. Each ingot was homogenized in vacuum for 48 hr followed by furnace cooling. Specimens from the ingots were then heat treated at 800, 900, 1000 or 1100 degree C for 2 hr followed by water quenching. The hardness and microstructure of each specimen was compared to the baseline material (55-Nitinol, 55 at.% nickel - 45 at.% titanium, after heat treatment at 900 degC). The results show that eleven of the studied compounds had higher hardness values than the baseline material. Moreover, twelve of the studied compounds had measured hardness values greater 600HV at heat treatments from 800 to 900 degree C.

Explore related subjects

intermetallicsphotomicrographyVickers hardnessmetallography

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Stanford, Malcolm K.. 2016-01-01. Hardness and Microstructure of Binary and Ternary Nitinol Compounds. https://ntrs.nasa.gov/citations/20160001689

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2024

Metallurgical and Thermal Properties of 57Ni–40Ti–3Hf (wt%)

Selected properties of 57Ni-40Ti-3Hf (wt%) were measured to further develop this material for use in aerospace rolling-element bearings. The average grain size and microindentation hardness of the material at room temperature were 90 μm and 549 HV, respectively. From room temperature to 500 °C, electrical resistivity increased from 8.9×10 –7 to 11.3×10 –7 Ω⋅m, thermal expansion coefficients varied from 1.1×10 –5 to 1.2×10 –5 mm/mm⋅°C, specific heat increased from 0.44 to 0.53 W⋅sec/g⋅K, thermal diffusivity rose from approximately 0.003 to 0.005 cm 2 /sec and thermal conductivity increased from approximately 0.09 to 0.19 W/cm⋅K. The behavior of the material can be explained by well-known metallurgical theory. These results are expected to provide a basis for design and modeling of future aerospace components.

intermetallics↗
NASA NTRS2018

Fractographic Analysis of 60-Nitinol Bearing Races

Fracture surfaces on a failed bearing race made from 60-Nitinol (60 wt% Ni - 40 wt% Ti) were analyzed. The bearing had experienced excessive localized heat due to an issue during machining that may have resulted in dimensional distortion. However, the classical fracture features that were identified by scanning electron microscopy and the fracture origins coincided with high concentrations of TiC-based contamination. Lessons learned for processing and quality control are discussed. An attempt to use x-ray diffraction to directly measure residual stresses imparted from the required heat treatment is also discussed.

intermetallics↗
NASA NTRS2017

Ni-Ti Alloys for Aerospace Bearing Applications

Nickel-rich Ni-Ti alloys are emerging candidate materials for aerospace bearing applications. These alloys exhibit a unique combination of physical, chemical, and tribological properties that are highly relevant to challenging aerospace bearings and other mechanical components. Despite being made solely from metals, Ni-Ti alloys are classified as intermetallics with properties akin to both metals and ceramics. For instance, like metals, they are electrically conductive but they tend to be brittle like ceramics. When properly processed, they have high hardness, low elastic modulus and an extensive elastic deformation range that imparts extraordinarily high resilience and resistance to denting. New alloy compositions enable simpler thermal processing and machining and intensive microstructural analyses have helped elucidate the materials science mechanisms governing hardness. In this paper, the application of state-of-art in NiTi alloys for aerospace bearings and mechanical components is explored. In addition to reviewing future trends and remaining challenges, the unique approaches and methods of tailoring bearing design to accommodate NiTis unique properties is discussed.

intermetallics↗