Development of an Adsorption System for the Trash Compaction Processing System designed for operation in the International Space Station Express Rack

Gregory S Pace; Jeffrey M Lee; Tra My Justine Richardson; Kevin Martin; Jurek Parodi; Serena Trieu; Janine Young

Home/Archive/NASA NTRS

NASA NTRS · 20205004415

Development of an Adsorption System for the Trash Compaction Processing System designed for operation in the International Space Station Express Rack

Gregory S Pace·Jeffrey M Lee·Tra My Justine Richardson·Kevin Martin·Jurek Parodi·Serena Trieu·Janine Young

View original source ↗Export metadata ↓

Abstract

A water recovery system that utilizes adsorption to work with the Trash Compaction Processing System, formerly known as the Heat Melt Compactor, is being designed at NASA Ames Research Center as an option to current state of the art micro-gravity water management systems and contaminant control systems used in space. The adsorption system will be used in conjunction with the International Space Station Vacuum Exhaust system to avoid both the complexities of gas liquid phase separation in micro-gravity and venting of Trash Compaction Processing System effluents to the spacecraft cabin. The adsorption system will allow the water and gaseous effluents generated during the Trash Compaction System operation to be removed in a matter that meets the Vacuum Exhaust System venting rate requirements. The Trash Compaction Processing System is planned to fly as a Technology Demonstration on the International Space Station in the space station EXPRESS Rack facility. This paper describes the trade space that the adsorption system must operate in using the EXPRESS Rack facilities resources including the use of the Space Station Vacuum Exhaust System. Also described in this paper are design solutions to allow the adsorption system to function within the Express Rack and Vacuum Exhaust System Parameters.

Explore related subjects

Heat Melt Compactor HMC Trash Compaction and Processing System TCPS adsorption vacuum exhaust system VES waste solid waste ISS

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Gregory S Pace, Jeffrey M Lee, Tra My Justine Richardson, Kevin Martin, Jurek Parodi, Serena Trieu, Janine Young. 2020-07-31. Development of an Adsorption System for the Trash Compaction Processing System designed for operation in the International Space Station Express Rack. https://ntrs.nasa.gov/citations/20205004415

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2021

Trash Compaction and Processing System Trash Models and Evolved Gas Analysis of Trash Components

As part of the NASA Next Space Technologies for Exploration Partnerships (NextSTEP) Trash Compaction and Processing System (TCPS) program, the Generation 2 (Gen 2) Heat Melt Compactor (HMC) tests a variety of trash models (nominal, high liquid, and high cloth) in order to evaluate the technical risk associated with processing spacecraft trash. The trash components used in the trash models not only impacts the final solid trash disk quality, but also the water and gas effluent compositions. In order to better design an auxiliary system to treat the effluent streams, both the input trash components and the effluent must be characterized. Evolved gas analysis (EGA) methods are used to characterize the input trash components. The EGA results will be used to determine various HMC operational parameters, as well as to determine the optimal operation for the TCPS system.

Heat Melt Compactor↗

NASA NTRS2013

Analysis of Water Recovery Rate from the Heat Melt Compactor

Human space missions generate trash with a substantial amount of plastic (20% or greater by mass). The trash also contains water trapped in food residue and paper products and other trash items. The Heat Melt Compactor (HMC) under development by NASA Ames Research Center (ARC) compresses the waste, dries it to recover water and melts the plastic to encapsulate the compressed trash. The resulting waste disk or puck represents an approximately ten-fold reduction in the volume of the initial trash loaded into the HMC. In the current design concept being pursued, the trash is compressed by a piston after it is loaded into the trash chamber. The piston face, the side walls of the waste processing chamber and the end surface in contact with the waste can be heated to evaporate the water and to melt the plastic. Water is recovered by the HMC in two phases. The first is a pre-process compaction without heat or with the heaters initially turned on but before the waste heats up. Tests have shown that during this step some liquid water may be expelled from the chamber. This water is believed to be free water (i.e., not bound with or absorbed in other waste constituents) that is present in the trash. This phase is herein termed Phase A of the water recovery process. During HMC operations, it is desired that liquid water recovery in Phase A be eliminated or minimized so that water-vapor processing equipment (e.g., condensers) downstream of the HMC are not fouled by liquid water and its constituents (i.e., suspended or dissolved matter) exiting the HMC. The primary water recovery process takes place next where the trash is further compacted while the heated surfaces reach their set temperatures for this step. This step will be referred to herein as Phase B of the water recovery process. During this step the waste chamber may be exposed to different selected pressures such as ambient, low pressure (e.g., 0.2 atm), or vacuum. The objective for this step is to remove both bound and any remaining free water in the trash by evaporation. The temperature settings of the heated surfaces are usually kept above the saturation temperature of water but below the melting temperature of the plastic in the waste during this step to avoid any encapsulation of wet trash which would reduce the amount of recovered water by blocking the vapor escape. In this paper, we analyze the water recovery rate during Phase B where the trash is heated and water leaves the waste chamber as vapor, for operation of the HMC in reduced gravity. We pursue a quasi-one-dimensional model with and without sidewall heating to determine the water recovery rate and the trash drying time. The influences of the trash thermal properties, the amount of water loading, and the distribution of the water in the trash on the water recovery rates are determined.

Heat Melt Compactor↗

NASA NTRS2013

Characterization of Heat Melt Compactor (HMC) Product Water

The Heat Melt Compactor (HMC) is designed to sterilize and process wastes produced during space missions. Benefits of the HMC include reduction of biohazards to the crew, reduction in volume of wastes that would otherwise require storage, production of radiation shielding tiles, and recovery of water and other resources. Water reuse is critical onboard spacecrafts; it reduces the need for resupply missions and saves valuable storage space. The main sources of water in HMC batches are food, beverages, shampoo, disinfecting wipes, toothpaste, and diapers. Water reclaimed by the HMC was analyzed for concentrations of Na+, NH4+, K+, Mg2+, Ca2+, Cl-‐, NO2-‐, Br-‐, NO3-‐, PO43-‐, SO42-‐, total organic carbon (TOC), total inorganic carbon (TIC), % total solids, and pH. The data are discussed in relation to the current water input characteristics established for the International Space Station Water Processor Assembly system. Batches with higher than average amounts of food produced HMC product water with higher sulfate content, and batches with higher proportions of disinfectant wipes and food yielded HMC product water with higher ammonium concentration. We also compared theoretical chemical composition of HMC product water based on food labels and literature values to experimental results.

Heat Melt Compactor↗