Search NASA⌕ Search

DOE OSTI · 22105900

Source term characterization for SNM pit storage facilities

Abstract

In order to properly design a mobile system to validate and verify the presence of special nuclear materials for non-proliferation and safeguards applications, accurate modeling of source materials is imperative. In this work, models were developed for use in design assessments based on an AL-R8 SNM standardized container specification to determine the radioactive signatures for both highly enriched uranium (HEU) and weapons plutonium (WGPu) special nuclear materials (SNM) housed in the containers. Intrinsic gamma boundary leakage currents were evaluated for this system, performed using 3D fixed-source deterministic SN photon transport (PENTRAN) as well as with stochastic Monte Carlo methods (MCNP5). Group-dependent leakage radiation terms were calculated at two 'source box' interfaces within the models, one directly surrounding the SNM source, and one immediately surrounding the canister. Analysis showed good agreement between the two models for energy groups of interest, based on a 24 group gamma library established for HEU and WGPu gamma signatures of interest. Intrinsic and neutron induced gamma leakage was determined using Monte Carlo calculations, and the combined gamma signatures were then treated as a net gamma leakage to be used in subsequent photon transport calculations. Neutron leakage based on the BUGLE-96 47 group structure was determined using Monte Carlo calculations for the WGPu canisters. These results will be used to evaluate the source term from stored nuclear materials and augment our efforts to design a detection system to validate the presence of these materials for safeguards purposes. (authors)

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Chin, M., Paul, J., Sjoden, G.. 2012-07-01. Source term characterization for SNM pit storage facilities. https://www.osti.gov/biblio/22105900

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗