Search NASA⌕ Search

DOE OSTI · 974330

NDA SYSTEM RESPONSE MODELING AND ITS APPLICATION

Abstract

The Portsmouth gaseous diffusion plant (PORTS) is a uranium enrichment facility that was historically used to enrich uranium to levels that range from 2% to greater than 97%. The feed material for PORTS was obtained from the Paducah Gaseous Diffusion Plant (PGDP) that produced uranium in the form of UF6 that was enriched to about 1 to 2%. The enrichment process involves a multistage process by which gaseous UF{sub 6} passed through a diffusion barrier in each stage. The porous diffusion barrier in each stage retards the rate of the diffusion of the heavier {sup 238}U atoms relative to the diffusion of the lighter {sup 235}U atoms. By this process the product stream is slightly enriched by each stage of the process. Each stage consists of a compressor, converter and a motor. There are more than 4000 stages that are linked together with piping of various diameters to form the PORTS cascade. The cascade spans three interconnected buildings and comprises miles of piping, thousands of seals, converters, valves, motors, and compressors. During operation, PORTS process equipment contained UF{sub 6} gas with uranium enrichment that increased in the process stream from the first to the last stage in a known manner. Gaseous UF{sub 6} moving through the PORTS process equipment had potential to form deposits within the process equipment by several mechanisms, including solidification due to incorrect temperature and pressure conditions during the process, inleakage of atmospheric moisture that chemically reacts with UF{sub 6} to form hydrated uranyl fluoride solids, reduction reactions of UF{sub 6} with cascade metals, and UF{sub 6} condensation on the internal equipment surfaces. As a result, the process equipment of the PORTS contains a variable and unknown quantity of uranium with variable enrichment that has been deposited within the equipment during plant operations. The exact chemical form of this uranium is variable, although it is expected that the bulk of the material is of the form of uranyl fluoride that will become hydrated on exposure to moisture in air when the systems are no longer buffered. The deposit geometry and thickness is uncertain and variable. However, a reasonable assessment of the level of material holdup in this equipment is necessary to support decommissioning efforts. The assessment of nuclear material holdup in process equipment is a complex process that requires integration of process knowledge, nondestructive assay (NDA) measurements, and computer modeling to maximize capabilities and minimize uncertainty. The current report is focused on the use of computer modeling and simulation of NDA measurements.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Vinson, D. 2010-03-01. NDA SYSTEM RESPONSE MODELING AND ITS APPLICATION. https://doi.org/10.2172/974330. https://searchnasa.com/record/osti%3A974330/nda-system-response-modeling-and-its-application

Citations retain the original authors and DOI and include this site’s record URL. If this discovery service contributed to your research, you can also cite Search NASA by Indiciae: BibTeX · RIS.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗