SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
System includes procedure for hermetically sealing solid materials and fluids in glass ampoule and use of temperature-controlled facility containing sample holder, which permits sample containers to be retrieved safely and conveniently. Solid material and fluid are sealed within chemically-clean glass ampoule according to highly detailed procedure.
A ruggedness evaluation of approaches to damage threshold testing was performed to determine the influence of three procedural variables on damage threshold data. The differences between the number of test sites evaluated at an applied fluence level (1 site versus 10 sites), the number of laser pulses at each test site (1 pulse versus 200 pulses), and the beam diameter (0.35 mm versus 0.70 mm) were all found to significantly influence the damage threshold data over a 99-percent confidence interval.
Report describes tests of paints (primers and topcoats) for use in recoating rusted carbon steel for protection against further corrosion. Paints selected for evaluation all designated by manufacturers as suitable for application over tightly adhering rust.
A comparative thermal conductance test was conducted to evaluate thermal interface materials for use on the Modular Power Subsystem. Materials tested included three thermal pads, four RTV adhesives, bare metal, and one thermal grease. The tests were conducted in a bell jar at vacuum conditions using a 1400 square centimeter footprint and two relatively low contact pressures, 207 kPa and 620 kPa. Power inputs ranged from 100 to 500 watts, and the thermal interface conductance values ranged from 100 to 1700 W/m2 C for the interstitial materials tested. In general, the thermal pads performed a little better than bare metal, while the RTV adhesives performed significantly better than the bare metal and comparable to the thermal grease.
Test program simulating solar wind outside magnetosphere to evaluate high melting point high density ceramic oxides as white thermal control coating pigments
Laboratory tests performed to characterize candidate encapsulation materials with respect to changes in their physical and chemical properties caused by photothermal aging are described. Several key material properties relating directly to material degradation and deterioration of performance were identified and were monitored as functions of aging conditions and time. A status report on accelerated testing activities is provided and experimental data are presented. It will be updated periodically as more data become available.
The goal of the program is to identify, test, evaluate and recommend encapsulation materials and processes for the fabrication of cost-effective and long life solar modules. Of the $18 (1948 $) per square meter allocated for the encapsulation components approximately 50% of the cost ($9/sq m) may be taken by the load bearing component. Due to the proportionally high cost of this element, lower costing materials were investigated. Wood based products were found to be the lowest costing structural materials for module construction, however, they require protection from rainwater and humidity in order to acquire dimensional stability. The cost of a wood product based substrate must, therefore, include raw material costs plus the cost of additional processing to impart hygroscopic inertness. This protection is provided by a two step, or split process in which a flexible laminate containing the cell string is prepared, first in a vacuum process and then adhesively attached with a back cover film to the hardboard in a subsequent step.
An apparatus for positioning and holding material specimens is a major subsystem of a system for impact testing of the specimens at temperatures up to 1,500 C. This apparatus and the rest of the system are designed especially for hot impact testing of advanced ceramics, composites, and coating materials. The apparatus includes a retaining fixture on a rotating stage on a vertically movable cross support driven by a linear actuator. These components are located below a furnace wherein the hot impact tests are performed (see Figure 1). In preparation for a test, a specimen is mounted on the retaining fixture, then the cross support is moved upward to raise the specimen, through an opening in the bottom of the furnace, to the test position inside the furnace. On one side of the furnace there is another, relatively small opening on a direct line to the specimen. Once the specimen has become heated to the test temperature, the test is performed by using an instrumented external pressurized-gas-driven gun to shoot a projectile through the side opening at the specimen.
NASA’s Science Mission Directorate (SMD) created the Asteroid Threat Assessment Project (ATAP) to inform decision-makers of risks associated with Potentially Hazardous Objects (PHOs), which may pose an existential threat to human civilization. ATAP assesses risk, in part, by developing analytical physics-based damage models which draw upon data collected during material property characterization efforts, entry simulations, hazard simulations, and ground-based arc-jet testing. Therefore, a pathfinder test campaign was con-ducted at the Hypersonic Materials Environmental Test System (HyMETS) at the NASA Langley Re-search Center to investigate the ablation mechanisms of an ordinary chondrite (Tamdakht H5) and a terrestrial analog (basalt). The HyMETS facility is a 400 kW constricted arc heater used to screen material performance under simulated aerothermal conditions of hypersonic flow.1 Facility conditions were chosen to simulate Earth entry conditions be-tween the upper-mesosphere and the lower thermo-sphere. The ablation mechanisms of Tamdakht and bas-alt are illustrated with still images collected from high-speed video cameras (fig. 1, Tamdakht). Tamdakht produces a relatively stable melt flow, as evidenced by the perpetual growth of a flange at the sidewall and the exiguous detachment of molten material into the flow. Furthermore, an inspection of high-speed video and chemical analysis of the post-test melt layer suggests that the dominant mode of mass loss for Tamdakht, at these test conditions, is expressed through the vaporization of volatiles (e.g., iron, potassium, sodium, phosphorus, and sulfur). The vaporization rates of Tamdakht are greater than basalt under the most extreme test conditions, which leads to an enhanced blowing layer, in-creased thermal shielding, and reduced recession. The ablation mechanisms of basalt are markedly different from Tamdakht and are attributed to the presence of hydrated minerals dispersed at irregular intervals throughout the silicate matrix. Rapid de-composition of secondary minerals and the subsequent formation of water lead to the ejection of the subsurface and overlying melt layer. Furthermore, the presence of water is suspected of lowering the viscosity of the melt layer resulting in increased mass loss near the edge of the test article where drag forces overcome rheological properties (fig. 1, bas-alt). Finally, the results will be discussed in the broader context of meteorite-based material response model development and the potential impact on the Asteroid Threat Assessment Project (ATAP).
A study of potentially useful low cost encapsulation materials for the Flat-Plate Solar Array project is discussed. The goal is to identify, evaluate, test and recommend encapsulant materials and processes for the production of cost-effective, long life solar cell modules. Technical investigations included studies of aging and degradation of candidate encapsulation materials, continued identification of primers for durable bonding of module interfaces, continued evaluation of soil resistant treatments for the sunlit surface of the module and testing of corrosion protective coatings for use low cost mild steel substrates.
In the previous lecture, the issues related to arcjet flow modeling were introduced, and the limitations of conventional instrumentation in addressing these issues were discussed. The general level of understanding of the arcjet flows was seen to preclude the use of arcjets as aerothermodynamic test facilities beyond the current role in aerothermal material testing, despite their long test duration capability. In this section, the focus will be on new developments in spectroscopic instrumentation and techniques that can be brought to bear on the fundamental problem of arcjet stream characterization. Although a wide selection of arcjet facilities were introduced in the previous section, the discussion of nonintrusive diagnostic instrumentation will be restricted to the large-scale, segmented, constricted-arc heater facilities that are most widely used in thermal protection material testing for aerospace applications. After a brief review of the important features of arcjet flows, the topic of nonintrusive, optical diagnostics is introduced with a discussion of some of the basic aspects of radiative transitions. The lecture is then organized into two sections covering emission measurements and laser-induced fluorescence measurements. Emission measurements are presented next for different regions of arcjet flows, while the fluorescence measurements are presented for the free stream region only. Summaries are given for each of the two main sections, and observations on arcjet characterization by optical diagnostics in general are given at the end.
Mechanical test facility for measuring deformation and fracture stresses in tension of brittle ceramic material
The diffusive and adsorptive properties of the Martian regolith influence the exchange of volatiles between the atmosphere and subsurface. Our quantitative knowledge of these properties is extremely poor -introducing substantial uncertainties in efforts to model long-term evolution of ground ice and diurnal, seasonal, and climatic cycles of CO2 and H20. This situation should significantly improve upon arrival of the 2001 Mars Surveyor Lander in 2002. In support of the Human Exploration and Development of Space (HEDS) enterprise, the 2001 mission will include a suite of instruments to characterize the nature of the Martian environment and assess whether it contains hazards that may threaten future human exploration. A major element of this effort is the Mars Environmental Compatibility Assessment (MECA) payload, which consists an optical microscopy system incorporating electrostatic, magnetic, and scratch-hardness materials testing palets, an atomic force microscope with imaging capabilities comparable to an SEM, a wet chemistry laboratory with four independent test cells, an electrometer on the robotic arm, material test patches, a camera also mounted on the arm, and a soil scoop for excavating down to about 50 cm into the soil. Although conceived to address the needs of HEDS, MECA payload is a sophisticated soil science laboratory that should provide a wealth of new data relevant to the volatile transport and storage properties of the regolith. Additional information os contained in the original.
The input design constraints applied to the extravehicular activity (EVA) spacesuit pose a significant challenge for mitigation of fire hazards. To minimize fatigue and increase comfort of the crewmember operating the suit, the suit pressure is lowered below sea level conditions with typical EVA suit designs operating with 4.3 psia (29.7 kPa). With the lowered operating pressures and the use of closed-loop life support, the suit requires elevated concentrations of oxygen, typically >95%. At these oxygen concentrations, nearly the entirety of the suit internal materials are flammable. This leaves one remaining possible control leg of the fire triangle: ignition sources. Since the Gemini and Apollo programs, this has been a risk that has undergone constant reassessment, with a focus on improved mitigation. After the Apollo I fire, an arc ignition method was developed and used to quantify ignition thresholds for in-suit materials resulting in a current limit for powered in-suit devices applied to all subsequent suit designs. After the discovery of a frayed spacesuit biomed cable on STS-113 during the Shuttle Program, the previous arcing method was repeated with additional methods developed to extend the testing further. One of those methods was wire-break ignition testing, in which the current in a single strand of wire was progressively increased, preheating the material in proximity with a resultant break and the application of a reasonably repeatable arc to ignite the material, all while exposed in the selected environment. This method was used to test a suite of spacesuit materials providing relative performance with respect to ignition with this configuration for application of energy. This paper discusses extension of the current data set to address recent material additions, lowering of energy test levels for quantification of materials too low to measure in previous testing, as well as future plans to improve this method.
Materials for solar-cell module construction have been studied on the basis of limited real-time outdoor exposure evaluations. The materials tested included transmission samples, sub-modules, and actual solar cells. The results suggest that glass, fluorinated ethylene propylene, and perfluoroalkoxy are good materials for the covering or encapsulation of solar-cell modules. In all cases, dirt accumulation and cleanability are important factors.
A novel concept of multilayer micro structurally controlled noise mitigation porous material was developed and experimentally validated in the laboratory by normal incidence impedance test. Extensive parametric studies were made to understand various parameters that influence acoustic absorption and transmission loss based on the test specimen size, particle size, porosity, pore size, and its distribution through the thickness. The results were reported in many publications. This work was focused on applying the concept and assessing the validity of the technology to aircraft turbomachine engines. The NASA Glenn Research Center’s Advanced Noise Control Fan (ANCF) low-speed test rig was selected. The liner insert required a 4-ft internal diameter cylinder with a 2-inch thick and 9-inch axial length. The liner was fabricated in eight segments and assembled in an aluminum test rig. The liner was tested for both tonal and broadband noise at the Notre Dame Turbomachinery Lab White Field test facility, where the ANCF is located. The study concludes that: Microstructurally controlled porous material is very effective in dissipating the sound energy; the liner is effective for tonal noise (2 to 13 dB reduction in noise levels) that constitutes the major part of the overall fan noise, especially the blade passing frequency which is generally the dominating component; Also, the liner is effective for broadband noise with reductions in sound pressure level of about 3 dB for the shaft order greater than 20. The proposed two-layer liner model demonstrated the validity of the concept. More studies are required to optimize the design.
Torsional testing facility for delayed elastic and nonrecoverable strains in materials, noting application to diffraction limited reflecting optics
The outgassing properties of materials and other considerations on materials acceptance for space applications are discussed. The uses of the outgassing data for the evaluation of important performance characteristics of a space system are indicated. The deficiencies and advantages of the ASTM-E595-77 test method and materials acceptance criteria are discussed. Also discussed are the advantages for the selection of the materials and the uses of the data provided by the long-term measurements of the outgassing rates and surface re-emission of materials. The paper concludes that the results of the ASTM method with additional derived data on the material properties can be used for the initial evaluation of a space system's characteristics. Materials data on outgassing and re-emission rates at various temperatures obtained from the more expensive, long-term QCM and TGA measurements should be obtained when a detailed analysis of a system is suggested based on the various considerations discussed in the paper.