Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polyolefin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

In‐Process Melt Separation of PE/PET Blends for Upcycling via Twin‐Screw Extrusion. Impact of Catalyst Reagents on PET Depolymerization

Part 1 of this work focused on depolymerizing polyethylene terephthalate (PET) in twin-screw extrusion, as part of a broader project to continuously separate PET from polyolefins in the melt. This study focused on linear low-density polyethylene (LLDPE) and PET films and the use of ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), and bis(2-hydroxyethyl) terephthalate (BHET) to depolymerize the PET in the extruder to levels above 90% Mw. In part 2, the focus will shift to achieving separation of the two polymers in the twin-screw extruder, which is made possible due to a 90% reduction in the Mw of the PET, which caused a decrease of its viscosity by several orders of magnitude. Owing to the viscosity difference and pressure buildup in the die, the low-viscosity PET preferentially exited a degassing vent instead of going through the die. This is because the flow of the PET would travel through a non-pressure vent rather than through a high-pressure die. However, owing to the higher viscosity of the LLDPE, the pressure was too high to pass through such a small diameter vent hole. Supercritical CO₂ (SCCO₂) was used to assist in this extraction, but SCCO₂ negatively impacted the overall degree of separation. Through analysis of the separated materials, it was concluded that a very high separation of the two materials was achieved. TGA and FTIR confirmed that the material separated from the vent was 100% PET. The material removed from the die was composed of 90% LLDPE and 10% PET.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of illumination and encapsulant resistivity on polarization-type potential-induced degradation on n-PERT cells

Power loss caused by polarization-type potential-induced degradation (PID-p) in a variety of high-performance photovoltaic cell types has been observed to be recoverable via subsequent illumination and in some cases preventable via simultaneous illumination. In this report, we describe the results of a study in which the front faces of n-PERT cells encapsulated in polymers with a broad range of electrical resistivity were exposed to varying and controlled irradiance during PID testing. For a low resistivity ethylene-vinyl acetate copolymer encapsulant, no reduction in the rate or extent of power loss was observed for irradiance as high as 1,000 W/m 2 , whereas for high and intermediate resistivity polyolefin encapsulants, 100 and 300 W/m 2 , respectively, prevented power loss. We introduce a simple model based on charge accumulation that facilitates interpretation of these results whereby degradation via charge accumulation under voltage stress and recovery due to light exposure are opposing and interdependent phenomena that describe the susceptibility of a module to power loss.

14 SOLAR ENERGY↗
DOE OSTI2021

Electrochemical Degradation Modes in Bifacial Silicon Photovoltaic Modules

Motivated by the rapidly rising deployment of bifacial monocrystalline-silicon photovoltaics (PV), we investigate the durability of various PV module packaging configurations with transparent coverings on both the front and rear sides of the module. We use a series of bifacial passivated emitter and rear cell (p-PERC) mini-modules with systematically varying outer cover materials (glass/glass, G/G, or glass/transparent backsheet, G/TB) and encapsulant chemistries (poly [ethylene-co-vinyl acetate], EVA; or polyolefin, POE). We study degradation modes over 1,000 hours of combined damp heat (DH) exposure and high system voltages that can cause potential-induced degradation (PID) under positive, zero, or negative 1,000 V cell-to-frame bias. We analyze the degradation modes using a combination of current-voltage measurements, impedance spectroscopy, external quantum efficiency, and spatially resolved luminescence and thermal imaging. Our results highlight various types of degradation including shunting, enhanced recombination, and series resistance increases, and we use spatially resolved characterization to separately identify the localized effects. We show that multiple PID and moisture-ingress degradation modes severely affect EVA-containing modules, with previously reported PID processes under negative-bias DH and a unique observation of rear-side surface recombination in G/EVA/G modules under positive-bias DH. We observe significantly less degradation in POE-containing modules, where the G/POE/G configuration exhibits minimal degradation under all stress conditions that we employ.

14 SOLAR ENERGY↗
DOE OSTI2022

Chemical and mechanical interfacial degradation in bifacial glass/glass and glass/transparent backsheet photovoltaic modules

Abstract Glass/glass (G/G) photovoltaic modules are quickly rising in popularity, but the durability of modern G/G packaging has not yet been established. In this work, we examine the interfacial degradation modes in G/G and glass/transparent backsheet modules under damp heat (DH) with and without system bias voltage, comparing emerging polyolefin elastomer (POE) and industry‐standard poly(ethylene‐co‐vinyl acetate) (EVA) encapsulants. We investigate the transport of ionic species at cell/encapsulant interfaces, demonstrating that POE limits both sodium and silver ion migration compared with EVA. Changes to the chemical structures of the encapsulants at the cell/encapsulant interfaces demonstrate that both POE and EVA are more susceptible to degradation in modules with a transparent backsheet than in the G/G configuration. Adhesion testing reveals that POE and EVA have comparable critical debond energies after the DH exposures regardless of system bias polarity. The results of this study indicate that the interfacial degradation mechanisms of G/G appear to be similar to those of conventional glass/backsheet modules. For emerging materials, our results demonstrate that POE offers advantages over EVA but that transparent backsheets may accelerate encapsulant degradation due to increased moisture ingress when compared with the G/G structure.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluation of bifacial module technologies with combined–accelerated stress testing

In view of the increasing interest and market share of bifacial cells and modules, suitable substrates such as glass and transparent backsheets along with ethylene vinyl acetate (EVA) and polyolefin elastomer (POE) encapsulants were examined in combined-accelerated stress testing (C-AST) to evaluate and compare degradation modes. Testing with both monofacial and bifacial cells, we found glass-glass modules with monofacial cells led to greater grid finger breakage than those with polymeric backsheets. Furthermore, this is attributed to previous X-ray topography and modeling work showing higher stress in cells and interconnections in glass-glass modules than glass-backsheet modules. Consistent with the objectives of C-AST, which stresses modules at levels corresponding to the limits seen in the natural environment, we observed the UV-fluorescence signatures of modules tested in C-AST (considering the degradation associated with developing chromophores, moisture penetration and photobleaching effects) to be like those in fielded modules, more so than other chamber stress testing implemented for comparison. We found light-induced degradation (LID) in module types with regenerated (inactive) cells with C-AST, suggesting the possibility of LID destabilization in some field conditions. We could also distinguish potential-induced degradation (PID) on the back of the bifacial passivated emitter and rear cells (PERC) in C-AST. Confirming with ex-situ tests, we found polarization-type PID most prevalent in glass-glass modules with EVA as would be anticipated considering the greater leakage current through such module encapsulation. Unlike PID tests performed in the dark, which can lead to false positive PID test results, field-representative illumination is experienced by the modules on the front and back side while –1200 V system voltage is applied in C-AST, supporting the conclusion that this module type with glass-glass construction would be susceptible to PID in the field.

14 SOLAR ENERGY↗
DOE OSTI2023

Predicting encapsulant delamination in photovoltaic modules bridging photochemical reaction kinetics and fracture mechanics

Abstract Photovoltaic (PV) modules are subjected to environmental stressors (UV exposure, temperature, and humidity) that cause degradation within the encapsulant and its interfaces with adjacent glass and cell substrates. To save experimental time and to enable long‐term assessment with intensive degradation only taking place after many years, the development of predictive models is indispensable. Previous works have modeled the delamination of the ethylene vinyl acetate (EVA) encapsulant/glass and encapsulant/cell interfaces under field aging conditions with fundamental photochemical degradation reactions that lead to molecular scission and loss of interfacial adhesion, characterized by the fracture resistance, G c . However, these models were fundamentally limited in that the following aspects were not incorporated: (i) molecular crosslinking in the field, (ii) synergistic autocatalytic interactions of degradation mechanisms, (iii) connection between degraded encapsulant structure and its mechanical properties, and (iv) rigorous treatment of the plasticity contribution to G c with finite element models. Here, we present a time‐dependent multiscale model that addresses these limitations and is applicable to a wide range of encapsulants and interfaces. For the reference EVA encapsulant and its interfaces with the glass and cell, the presented model predicts an initial rise in G c in the first 3 years of field aging from crosslinking, then a subsequent sharp decline from degradation mechanisms. We used nanoindentation to measure the changes in EVA mechanical properties over exposure time to tune the model parameters. The model predictions of G c and mechanical properties match with experimental data and show an improvement compared to previous models. The model can even predict switches in failure interfaces, such as the observed EVA/cell to EVA/glass transition. We also conducted a sensitivity analysis study by varying the degradation and crosslinking kinetic parameters to demonstrate their effects on G c . Model extensions to polyolefin elastomer‐ and silicone‐encapsulants and their interfaces are also demonstrated.

Liu, Kuan↗
DOE OSTI2025

Impacts of Disulfide‐Containing Monomers in Alternating Diene Metathesis Polymerization

ABSTRACT Among the classes of synthetic polymers, disulfide‐containing structures offer unique opportunities due to their accessibility to redox chemistry that allows for degradation or reversible disulfide formation and exchange under mild conditions. Here, we examine the role of disulfides in olefin metathesis polymerization, specifically alternating diene metathesis (ALTMET) polymerization, for synthesizing unsaturated polyolefins with embedded disulfides. Our synthetic strategy hinged on the use of α,ω‐diacrylate monomers, including those connected by a disulfide unit, via copolymerization by the ALTMET mechanism to yield copolymers containing a range of disulfide content. In addition, the potential impacts of sulfur‐ruthenium interactions on the ALTMET process were investigated spectroscopically, while the degradation of the resultant polymers was affected by mild reducing agents. Overall, this study contributes to the development of degradable synthetic polymers using olefin metathesis methods, with an increased understanding of the potential for further use of disulfide groups in such metathesis reactions.

Lee, Kyoungwon↗
DOE OSTI2025

Structure-dependent mechanisms for plastic degradation in the marine environment

The visible and invisible accumulation of waste plastic in our oceans is a consequence of rapidly increasing inputs and very slow degradation rates. In general, this combination of effects results in long residence times. Nevertheless, the abiological degradation rate of a specific synthetic plastic varies widely, depending on its structural characteristics at the molecular, mesoscopic, and macroscopic levels. This chapter summarizes factors that determine these rates of degradation, and describes their principal mechanisms, for several of the major types of waste plastic found in the oceans. Mechanical forces cause cracking and flaking that break macroplastics into microplastics and even smaller fragments with increasing surface-to-volume ratios. Chemical degradation rates increase with surface area, influenced by intrinsic variations in crystallinity and the presence of additives, as well as extrinsic factors such as temperature, pH, and UV light intensity. Since polyolefin-based plastics are less dense than seawater and lack hydrolysable bonds in their polymer backbones, they accumulate close to the surface of the ocean where photo-oxidation is the principal cause of C–C bond cleavage in the polymer backbone. In contrast, polyesters and polyamides are denser than seawater and they sink, experiencing less exposure to solar irradiation. However, they can also degrade by slow hydrolysis of the C–O or C–N bonds intrinsic to the polymer structures.

Maciulis, Nicholas A.↗
DOE OSTI2021

Single pot catalyst strategy to branched products via adhesive isomerization and hydrocracking of polyethylene over platinum tungstated zirconia

Hydrocracking is an insufficiently explored route for chemical recycling of plastics waste. Platinum tungstated zirconia (Pt-WZr) was used in a batch reactor at low temperatures of 250 °C and 30 bar H 2 pressure for 1-24 h reaction times using low-density polyethylene (LDPE, M w ~76 kDa). We find Pt-WZr is a bifunctional catalyst for LDPE hydrocracking leading to higher value branched fuel- and lubricant-ranged alkanes. Here we demonstrate that the catalyst metal-to-acid site molar ratio (MAB) shifts the product distribution to larger cracked products and increases the isomerization degree in the residual polymer. We propose a new adhesive isomerization mechanism between the metal and Brønsted acid sites in parallel with slow polymer chain cracking, caused by competitive adsorption of the polymer over the liquid products and stereochemical hindrance of methines. This study provides a blueprint on how to engineer effective catalysts for hydrocracking polyolefin plastic wastes using the MAB as a catalyst descriptor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A high throughput assay to detect enzymatic polyethylene oxidation

Biological plastics deconstruction and upcycling have emerged as sustainable alternatives to traditional recycling technologies for plastics waste. The discovery and engineering of efficient thermostable poly(ethylene terephthalate) (PET) hydrolases have made biological PET recycling possible at scale; however, enzymes for non-PET plastics, which account for approximately 70% of all plastics produced, remain largely undiscovered. To accelerate the discovery of such enzymes, we develop a high-throughput screen to detect initial polymer oxidation, specifically that of the C-H bond to an aldehyde. We test 4-hydrazino-7-nitro-2,1,3-benxoxadiozole hydrazine (NBD-H), which reacts with generated aldehydes to form a fluorescent hydrazone on plasma oxidized low-density polyethylene (LDPE) films. Hydrazone generation correlated well with the area of aldehyde peaks as measured by Fourier Transform Infrared Spectroscopy (FTIR) (R2 = 0.92). Moreover, we demonstrate that the probe reliably identifies LDPE-active dye decolorizing peroxidases (DyPs) that generate aldehydes on LDPE films (1.7 – 3.0 fold change relative to background), serving as an effective screen as demonstrated by receiver operating characteristic area under the curve of 0.95. Furthermore, this assay offers an LDPE oxidation screening platform that can be readily parallelized and automated for accelerated discovery of enzymes involved in polyolefin deconstruction.

biocatalysis↗
DOE OSTI2025

Investigating the Role of Acid Sites in the Hydrocracking of Polyethylene-EVOH Multilayer Film Waste over Pt/BEA Catalyst

Multilayer polymer films (MFs) containing poly(ethylene-co-vinyl alcohol) (EVOH) and polyolefins are ubiquitous in single-use food and medical packaging. MFs are currently landfilled or incinerated rather than mechanically recycled because of the processing difficulties associated with their form factor and complex multicomponent structures. Advanced chemical recycling is a promising solution. Prior reports have explored hydrogenolysis and hydrodeoxygenation to convert EVOH, but these technologies are limited by catalyst deactivation and slow apparent kinetics, respectively. Alternatively, in this work, we demonstrate the efficient hydrocracking of commercial MFs into naphtha range (C5-C12) alkanes over platinum (Pt) supported on acidic zeolites. Mixtures of low-density polyethylene (LDPE) and EVOH are utilized as MF surrogates to gain fundamental insights. Pt deposited on BEA supports with varying Lewis acid site (LAS) concentrations are synthesized and tested for hydrocracking. Surprisingly, Pt/BEA with high LAS concentrations demonstrate improved activity for LPDE/EVOH blends over LDPE alone. In contrast, LAS concentrations are shown to have no influence on LDPE hydrocracking. LAS and Brønsted acid sites (BAS) catalyze the dehydration of EVOH to form water, which improves LDPE hydrocracking. Polyaromatics formed primarily via EVOH thermal degradation lead to detrimental coke formation, which hinders hydrocracking activity. Reaction conditions and feed ratios of LDPE and EVOH are tuned to balance these competing effects. Reusability tests demonstrate that Pt/BEA maintains high activity (81% conversion in 2 h) and high selectivity towards naphtha (78%) over multiple reuse cycles. Furthermore, these findings position hydrocracking as a promising technology for the circularity of complex MF plastic waste.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chemically and mechanically recyclable polyester-based multilayer plastics

Approximately 100 million tons of multilayered plastics (MLPs) are produced each year worldwide but are not recycled due to their complex structure. Here, this work aims to design polyester-based multilayer plastics (80–100 % polyester) that provide barrier performance comparable to typical 9–12-layer commercial MLPs, while also enabling both chemical recycling (back to parent monomer) and mechanical recycling (grind-and-melt reprocessing). Such dual recyclability is not achievable with non-polyester multilayers, such as all-polyolefin systems. Furthermore, we emphasize how the multilayer architecture was tailored to balance barrier properties, mechanical integrity, and end-of-life recyclability for both flexible and rigid packaging applications. Two main categories of polyester-based MLPs are reported; in the first type, poly(butylene adipate-co-terephthalate) (PBAT)-70 % polyglycolic acid (PGA) is used as middle barrier layer, while in second type, middle barrier layer is Ethylene-vinyl alcohol (EVOH) copolymers. Polyethylene terephthalate (PET) was used as a structural layer, while either PBAT or poly(butylene succinate) (PBS) was used to enable thermal sealing and serve as the product contact layer. These MLPs are recycled by both chemical and mechanical recycling processes. Techno-economic analysis (TEA) shows that MLPs incorporating EVOH as barrier layer have similar or lower selling costs (0.32 $\$$/m 2 ) than commercial MLPs. Life cycle assessment (LCA) indicates EVOH-based MLPs have a lower carbon footprint and lower energy consumption relative to commercial MLP benchmarks. This work offers simplified MLPs that are easy to manufacture and ready to recycle, which will significantly reduce environmental impact of MLP packaging while also providing a cost-effective and practical solution for industry.

Barrier properties↗
DOE OSTI2023

Bifunctional tandem catalytic upcycling of polyethylene to surfactant-range alkylaromatics

Catalytic conversion of waste polyolefins to value-added alkylaromatics could contribute to carbon recycling. Compared with tandem hydrogenolysis/aromatization of polyethylene (PE) catalyzed by Pt/γ-Al 2 O 3 at 280°C, both a 5-fold enhancement in the rate of C–C bond scission and a doubling of the molar yield of alkylaromatics were achieved using a more acidic Pt/F-Al 2 O 3 catalyst instead. Bifunctional (metal/acid) catalysts also generate alkylaromatic products with lower average carbon numbers (ca. C 20 ), similar to conventional anionic surfactants. Because physical mixtures of weakly acidic Pt/γ-Al 2 O 3 or non-acidic Pt/SiO 2 with strongly Brønsted acidic Cl-Al 2 O 3 or F-Al 2 O 3 are also effective, the tandem reaction does not require nanoscale intimacy between metal and acid active sites. Kinetic studies using triacontane (norm-C 30 H 62 ) as a model for PE show that the Pt-catalyzed dehydrogenation/hydrogenation reactions are quasi-equilibrated, while the acid-catalyzed C–C bond scission and skeletal transformations (isomerization and cyclization) determine the overall rates of depolymerization and aromatic formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mechanically and thermally robust microporous copolymer separators for lithium ion batteries

Next generation, multifunctional separators can enhance energy storage, power, and safety performance of lithium ion batteries but must be simple to fabricate and incorporate with existing roll-to-roll manufacturing. Here, this study presents a strategy to facilely prepare these separators using UV-initiated polymerization-induced phase separation (PIPS), wherein microporous polymer separators are fabricated directly from constituent monomers and ethylene carbonate (EC) porogen. This enables a wide compositional design space as co-monomers with specific chemical functionality can be readily incorporated into the PIPS precursor mixture. Herein, 1,4-butanediol diacrylate (BDDA) was copolymerized with poly(ethylene glycol) diacrylate (PEGDA) to increase the acrylate conversion in the photopolymerization and improve mechanical properties. By tuning the ratio of PEGDA and EC, separators with high porosity (41.3%) and effective ionic conductivity (2.09 mS cm –1 ) were prepared. Inclusion of PEGDA was essential to increasing the elastic modulus to > 345 MPa, which is required for cell assembly by roll-to-roll manufacturing. All separators prepared were shown to enable reversible cycling of lithium metal/LiNi 0.5 Mn 0.3 Co 0.2 O 2 half-cells for 100 cycles. Unlike conventional polyolefin separators, which were shown to melt at 160 °C and shrink by up to 29.8% at elevated temperatures, the PIPS separators possess exceptional, safety-enhancing thermomechanical properties, undergoing no phase transitions or thermal shrinkage.

25 ENERGY STORAGE↗
DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗
DOE OSTI2023

Treasuring trash: Pt/SrTiO 3 catalysts process plastic waste into high-value materials

Single-use plastics are ubiquitous throughout modern society because they have properties that make them desirable in a wide variety of applications, including low cost of production, high thermal and chemical stability, and tunable mechanical properties. Several of the recycling methods currently used to process single-use plastic waste, such as mechanical recycling and pyrolysis, do not selectively process plastic materials into uniform products, as would be advantageous for repurposing these materials in pursuit of a circular economy. Catalytic hydrogenolysis, whereby C–C bonds in polymers are broken over a supported catalyst in the presence of H 2 , is a promising approach to converting plastics into value-added products that can be sold commercially without further purification. Here, in this account, we present some recent advances in polyolefin hydrogenolysis, with a focus on Pt nanoparticles on SrTiO 3 nanocuboid supports (Pt/STO). Current developments in this field, general challenges, and future directions are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Connecting radiation-driven changes in structural, thermal, and mechanical properties in several medical device polymers

Stemming from security threats and shortages in supply, a recent push has emerged to develop alternatives to radioisotope Cobalt-60 gamma radiation for sterilization of polymeric medical products, including electron beam (e-beam) and X-ray machine-based sources. However, before large-scale implementation, the effects of these non-isotope-based methods must be thoroughly investigated from several perspectives, involving their potential detrimental effects on the structural, thermal, and mechanical properties of polymers in medical devices. This paper investigates such effects in commonly used medical device polymers, including polypropylene homopolymer (PPH), polyolefin elastomer (POE), low-density polyethylene (LDPE), acrylonitrile butadiene styrene (ABS), and chlorobutyl rubber (CIIR). To connect radiation-driven changes in polymer structural and thermal properties and corresponding changes in mechanical properties, several characterization techniques were utilized, including gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). We found that the tensile strength of X-ray irradiated PPH, as well as X-ray, e-beam, and gamma irradiated CIIR decreases due to chain scission, which is corroborated by GPC and DMA. The GPC results of LDPE suggest chain scission, but interestingly without a corresponding decline in tensile strength. By comparison, POE and ABS appear to undergo further crosslinking with increasing irradiation dose, which generally strengthens them. Importantly, in the vast majority of the cases, there were small to no changes in properties upon changing radiation technologies (at a given dose), i.e., no radiation source dependence. However, in a few specific cases, radiation method dependencies did arise, for instance, in terms of the molecular weight of PPH being significantly increased upon X-ray irradiation, while the melting temperature, glass transition temperature, and elongation at break reduced compared to gamma. Overall, this study provides valuable insight into radiation-driven chemical and structural changes in polymers that produce changes in physical and functional properties.

36 MATERIALS SCIENCE↗