Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface dislocations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Sensitization of 316L Stainless Steel made by Laser Powder Bed Fusion Additive Manufacturing

Additively manufactured (AM) 316L stainless steel (SS) manufactured by laser powder bed fusion (L-PBF) and wrought 316L SS were subjected to sensitization heat treatments at 700°C up to 100 h. Using two evaluation methods, double-loop electrochemical potentiokinetic reactivation (DL-EPR) and ditching tests, degree of sensitization (DOS) and intergranular corrosion (IGC) susceptibility was evaluated. It was found that the wrought samples showed slightly lower IGC susceptibility compared to their AM counterpart. DOS and IGC attacks increased with sensitization time for all samples. Dislocation cellular structures were found to have little to no impact on DOS and IGC for the AM samples. Sensitized at 100 h, the AM sample showed significant Cr depletion along high-angle grain boundaries (12.35 wt% on average) and exhibited Cr carbide precipitation. Mo-rich particles along grain boundaries were also observed. The DL-EPR test attacks the surface oxide film and grain boundaries while the ditching test attacks the melt pool boundaries and grain boundaries (IGC and pitting). Changes to the DL-EPR and ditching standards for AM application have been proposed in this work.

316L stainless steel↗
DOE OSTI2024

Grand canonically optimized grain boundary phases in hexagonal close-packed titanium

Grain boundaries (GBs) profoundly influence the properties and performance of materials, emphasizing the importance of understanding the GB structure and phase behavior. As recent computational studies have demonstrated the existence of multiple GB phases associated with varying the atomic density at the interface, we introduce a validated, open-source GRand canonical Interface Predictor (GRIP) tool that automates high-throughput, grand canonical optimization of GB structures. While previous studies of GB phases have almost exclusively focused on cubic systems, we demonstrate the utility of GRIP in an application to hexagonal close-packed titanium. We perform a systematic high-throughput exploration of tilt GBs in titanium and discover previously unreported structures and phase transitions. In low-angle boundaries, we demonstrate a coupling between point defect absorption and the change in the GB dislocation network topology due to GB phase transformations, which has important implications for the accommodation of radiation-induced defects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stress-dominated growth of two-dimensional materials on nonplanar substrates

Curved features are ubiquitous on solid surfaces, but the effect of surface curvatures on growth of two-dimensional (2D) materials has not yet been established. Using a newly developed method based on the Metropolis algorithm and taking graphene as a prototype, we find that a curved feature on substrates can result in a variety of topological defects in 2D materials. As the feature's size increases by just nanometers, the defects can vary from adatoms, dislocation pairs, and grain boundary scars to long-range grain boundaries, in contrast to previously reported defect-free modes of rigid colloidal crystals growing on spheres. We identify an important role of curvature-induced lattice stress in lowering the growth rate over the curved features and driving a plastic instability in the materials. When the feature's size increases to several nanometers, the stress effect is compromised by an enhanced effect of geodesic curvature, yielding long-range grain boundaries as a result of increased local growth rate on the feature with respect to that on flat regions. Here we further provide a ‘phase diagram’ of defects that helps to guide a rational choice of geometrical parameters of features towards the growth of high-quality 2D materials as well as controllable creation of topological defects.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructurally Strained Pyrochlore–Perovskite Biphasic Electrocatalysts for the Oxygen Evolution Reaction

Efficiency of water splitting for hydrogen production is often limited by the sluggish kinetics of multiple electronic transfers required in the heterogeneous oxygen evolution reaction (OER). Catalyst design for reducing the high OER overpotential remains a major scientific challenge. Lattice-strain engineering, a method for tuning the electronic structure and surface geometric configuration of active sites, may greatly affect the interaction between adsorbates and catalytic surfaces for high activity and stability. Here, in this study, we present the synthesis of biphasic oxides of YPrSrRuMnO x , which consists of distinct phases of Y 2 Ru 2 O 7 pyrochlore and (Pr 0.7 Sr 0.3 )MnO 3 perovskite, and the development of a suitable analytical approach to study the strain–catalytic property relationship. Linear sweep voltammetry results reveal that the biphasic oxide exhibits approximately 3.1 times greater mass activity and 2.4 times larger turnover frequency (TOF) than single-phase Y 2 Ru 2 O 7 in the 0.1 M HClO 4 electrolyte. The biphasic catalyst is also about 3 times more stable than the single-phase oxide under acidic conditions. X-ray photoelectron spectroscopy, nitrogen isotherm, and electrochemical surface area analyses indicate that the oxidation state, specific surface area, and electrochemical surface area do not cause enough difference in the observed enhancement of OER performance. We examined the effects of microstrain on electrocatalysis, originating from lattice mismatch between different phases, using three different structural models. Specifically, we compared the Williamson–Hall method, standard stress–strain analysis, and Rietveld refinement in analyzing the structure–property relationship. Strain mapping using geometric phase analysis (GPA) further revealed significant microstrain and lattice dislocations localized near phase boundaries in the biphasic oxide, in contrast to the uniform strain in single-phase materials. The results reveal that the increased microstrain correlates well with the improved OER performance, as the biphasic oxide catalyst exhibits 2–3 times greater microstrain than Y 2 Ru 2 O 7 pyrochlore.

electrocatalysts↗
DOE OSTI2024

On the role of geometrically necessary dislocations in void formation and growth in response to shock loading conditions in wrought and additively manufactured Ta

This study investigates the role of geometrically necessary dislocations (GNDs) and microstructure on void nucleation and growth in wrought and additively manufactured (AM) tantalum subjected to high-strain rate loading. Multi-modal 3D data was collected using TriBeam tomography to calculate GND densities and their spatial relationship to voids. A microstructural comparison between the wrought and AM samples identified distinct void shapes and locations, with intragranular voids and more spherical voids frequently observed in the AM dataset. Results indicate that voids preferentially form at both high-angle grain boundaries and low-angle subgrain boundaries, the latter of which are frequently observed in the AM material. Through a radial distribution analysis of all voids in the datasets, significant GND localization to near-void-surface regions was observed in both samples. 3D crystal plasticity simulations were employed to extend the experimental observations, revealing higher void growth rates in [111] oriented grains when compared to [001] grains. The simulations also suggest that GNDs can be generated as part of the void growth process, with more GND accumulation for growth in a [111] grain than a [001] grain. These findings provide valuable insights into the links between nanoscale void nucleation, mesoscale void growth, and microstructural effects in dynamically loaded tantalum.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct evidence of microstructure dependence of magnetic flux trapping in niobium

Abstract Elemental type-II superconducting niobium is the material of choice for superconducting radiofrequency cavities used in modern particle accelerators, light sources, detectors, sensors, and quantum computing architecture. An essential challenge to increasing energy efficiency in rf applications is the power dissipation due to residual magnetic field that is trapped during the cool down process due to incomplete magnetic field expulsion. New SRF cavity processing recipes that use surface doping techniques have significantly increased their cryogenic efficiency. However, the performance of SRF Nb accelerators still shows vulnerability to a trapped magnetic field. In this manuscript, we report the observation of a direct link between flux trapping and incomplete flux expulsion with spatial variations in microstructure within the niobium. Fine-grain recrystallized microstructure with an average grain size of 10–50 µm leads to flux trapping even with a lack of dislocation structures in grain interiors. Larger grain sizes beyond 100–400 µm do not lead to preferential flux trapping, as observed directly by magneto-optical imaging. While local magnetic flux variations imaged by magneto-optics provide clarity on a microstructure level, bulk variations are also indicated by variations in pinning force curves with sequential heat treatment studies. The key results indicate that complete control of the niobium microstructure will help produce higher performance superconducting resonators with reduced rf losses 1 related to the magnetic flux trapping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Modes of strain accommodation in Cu-Nb multilayered thin film on indentation and cyclic shear

Two-phase layered thin films with a high density of semi-coherent interfaces exhibit excellent mechanical properties and thermal stability. Here, in this study, a magnetron-sputtered Cu-Nb dual-layered thin film (~500 nm for Cu and ~150 nm for Nb) having an amorphous interface between Cu and Nb with a high density of aligned growth twins in Cu is subjected to severe surface deformation. The material is loaded using indentation and cyclic shear under tribological testing. The strain accommodation in the subsurface microstructure after deformation varies based on the local structure and deformation mode. Grain refinement and crack formations in the stressed region of the Nb layer and localized crystallization of the amorphous interface are observed after indentation and scratch testing. Pronounced detwinning of growth twins in the Cu layer under the cyclic shear strain leaves large dislocations sites and loops which are observed both by high-resolution transmission electron microscopy and experiment-guided molecular dynamic (MD) simulations. Our simulations provided insights into understanding the pathway for the detwinning process under cyclic shear loading.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Efficiency 6-Junction Solar Cells for the Global and Direct Spectra

We show 6-junction inverted metamorphic solar cells with high efficiencies under both the global and direct spectrum, and discuss improvements to device components. High voltage AlGaInP subcells are demonstrated on GaAs substrates miscut 2° towards (111)B by using Sb surfactant to reduce atomic ordering. This miscut enables high voltage and low dislocation density GaInAs subcells by using atomically-ordered GaInP-based graded buffers. One-sun efficiencies of 39.2 ± 1.3% under the global spectrum and 39.4 ± 1.1% direct spectrum have been demonstrated by using these high voltage subcell components. For high efficiency under the concentrated direct spectrum, low resistance is also necessary, which requires a challenging and nonintuitive optimization of tunnel junctions and heterobarriers. Increasing the thickness of a (Al)GaInAs spacer layer between the back surface fields (BSF) and tunnel junctions (TJ) of latticemismatched subcells reduces nonlinear resistance, which implies a detrimental interaction between the BSF and TJ. Concentrator devices with optimized spacer layers show reduced effective resistance and maintain fill factor > 75% at 1100 suns. Device efficiencies under the concentrated direct spectrum peak at 47.1 ± 3.2% at 143 suns.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2025

Three-dimensional nucleation and growth of deformation twins in magnesium

At two-thirds the weight of aluminum, magnesium alloys have the potential to reduce the fuel consumption of transportation vehicles. These advancements depend on our ability to optimize the desirable versus undesirable effects of deformation twins, which are three-dimensional (3D) microstructural domains that form under mechanical stresses. Previously only characterized through surface or thin-film measurements, we here present 3D in situ characterization of deformation twinning inside an embedded grain over mesoscopic fields of view using dark-field x-ray microscopy supported by crystal plasticity finite element analysis. The results revealed the role of triple junctions on twin nucleation and the sequence and irregularity of twin growth and showed that twin-grain junctions, twin-twin junctions, and twin boundaries were the sites of localized dislocation accumulation.

Lee, Sangwon [Univ. of Michigan, Ann Arbor, MI (Un↗
DOE OSTI2023

Taming the Pseudoelastic Response of Nitinol Using Ion Implantation

Implantation of Ni 50.5 Ti 49.5 wire with 30 MeV Ni 6+ ions at doses (< 0.1 DPA) typically smaller than employed in the literature is shown to systematically alter the pseudoelastic response, with extrema in Berkovich nanoindentation load (+50%), hysteresis (–60%), and recoverable displacement (–19%) occurring at ~ 3.6 μm below the implantation surface. These extraordinary values are attributed to ~ 10 to 20 nm amorphous clusters that constrain the stress-induced B2-B19' phase transformation. This is substantiated by phase field simulations of crystalline-amorphous composites and molecular dynamics simulations of crystalline-vacancy cluster composites showing the spatial refinement of martensite caused by nm-scale defects. Finally, the results suggest that ion implantation may potentially expand the processing and performance space for NiTi, by creating amorphous defects at smaller length scales than dislocation substructures produced by conventional deformation processing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Residual loss due to magnetic flux trapping in niobium superconducting microwave cavities

One of the significant source of radio frequency loss in superconducting microwave cavities is the trapped residual magnetic field during the cooldown due to the incomplete Messier effect. The sensitivity of flux trapping depends on the distribution of impurities, network of dislocations and defects which pin vortices. Recent advancement in cavity processing techniques resulted in very high quality factors with impurity doping, however the rf loss related to the flux trapping increases. High quality factor in SRF cavities is not only limited to particle accelerators but also emerging as an application to quantum computing and quantum information science. In this presentation, we present the results of measurements of flux trapping sensitivity on several 1.3 GHz elliptical accelerating cavities with different grain size, impurity content and surface preparations.

Dhakal, P.↗
DOE OSTI2022

Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions

Severe plastic deformation of 304L stainless steel plate was carried out by friction stirring under an isothermal tool temperature at 825°C. The friction stirred zone showed extensive grain refinement, high fraction of low angle grain boundaries due to dislocation rearrangement, Σ3 and Σ9 special grain boundaries and discrete Fe–Cr–Mn-rich particles. Electrochemical polarisation measurements were done on the base metal (BM) and friction stir welded (FSW) specimens in the neutral and acidified 3.5% NaCl solutions. The BM showed marginally better pitting resistance in the neutral chloride solution than the FSW because of a larger fraction of special grain boundaries, and larger grain size. Whereas in acidified 3.5% NaCl solution, the FSW showed better corrosion resistance than the BM. Furthermore, the surface film of the FSW had a lower impedance and a lower defect concentration than the BM indicating higher diffusivity of point defects in the FSW.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Deformation band corrosion as a result of applied stress and cold-work in 304 stainless steel in simulated pressurized water reactor primary water conditions

Stainless steels like 304SS are commonly used in pressurized water reactor primary water environments due to their excellent resistance to stress corrosion cracking (SCC). However, SCC susceptibility has been observed in cold-worked 304SS. Cold-rolling introduces a high density of defects, such as deformation bands or dislocations, into the microstructure; applied stress, even if macroscopically below the yield stress, can result in regions with high localized stresses. Cold-worked and non-cold-worked samples were exposed to 360 °C simulated PWR primary water for 1500 h with and without active loading. Corrosion susceptibility of dislocations and deformation bands induced by cold-rolling and/or applied stress was studied using high-resolution (analytical) transmission electron microscopy. Deformation bands were generated in all specimens examined in the study. Penetrative oxidation was observed in some deformation bands in each specimen. The depth of penetrative deformation band oxidation frequently exceeded the depth of grain boundary oxidation in all specimens. However, deformation band oxides generally were narrowly confined to the deformation band plane. Highly Ni-rich regions were observed beyond all oxidation fronts. Surface oxides were thicker in the specimens exposed under active loading. In conclusion, the implications of these findings at surfaces for deformation bands intersecting stress corrosion crack paths are discussed.

EFTEM↗
DOE OSTI2021

Bulk transport paths through defects in floating zone and Al flux grown SmB 6

We investigate the roles of disorder on low-temperature transport in SmB 6 crystals grown by both the Al flux and floating zone methods. We used the inverted resistance method with Corbino geometry to investigate whether low-temperature variations in the standard resistance plateau arise from a surface or a bulk channel in floating zone samples. The results show significant sample-dependent residual bulk conduction, in contrast to smaller amounts of residual bulk conduction previously observed in Al flux grown samples with Sm vacancies. In this work, we consider hopping in an activated impurity band as a possible source for the observed bulk conduction, but it is unlikely that the large residual bulk conduction seen in floating zone samples is solely due to Sm vacancies. We therefore propose that one-dimensional defects, or dislocations, contribute as well. Using chemical etching, we find evidence for dislocations in both flux and floating zone samples, with higher dislocation density in floating zone samples than in Al flux grown samples. In addition to the possibility of transport through one-dimensional dislocations, we also discuss our results in the context of recent theoretical models of SmB 6 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomistic simulations of He bubbles in Beryllium

Formation of He bubbles can have a significant effect on the microstructural evolution and properties of irradiated materials. In this report, we use atomistic simulations based on machine learning potentials to investigate the fundamental behavior of He bubbles in Be, with a specific focus on the shape, stability, and diffusivity of bubbles. Stability of He bubbles is quantified in terms of formation energies, which are determined as a function of the ratio of He/V. We find that He bubbles become unstable with respect to plastic deformation through punch-out dislocations around the bubble when the He/V ratio is larger than ~1.25, and the punch-out process induces the change of the regular bubble shape. In general, the bubble shape of He in Be is found to be ellipsoid-like. It is also found that for a fixed He/V ratio, the bubble attracts vacancies to become larger in size. If the bubble size is constant, the bubble attracts additional He atoms until the punch-out reaction occurs. The dominant diffusion mechanism of He bubbles changes from surface diffusion to volume diffusion as the temperature is increased, with a crossover occurring at about 900 K.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Size-dependent radiation damage mechanisms in nanowires and nanoporous structures

Nanostructures with a high density of interfaces, such as in nanoporous materials and nanowires, resist radiation damage by promoting the annihilation and migration of defects. This study details the size effect and origins of the radiation damage mechanisms in nanowires and nanoporous structures in model face-centered (gold) and body-centered (niobium) cubic nanostructures using accelerated multi-cascade atomistic simulations and in-situ ion irradiation experiments. Our results reveal three different size-dependent mechanisms of damage accumulation in irradiated nanowires and nanoporous structures: sputtering for very small nanowires and ligaments, the formation and accumulation of point defects and dislocation loops in larger nanowires, and a face-centered-cubic to hexagonal-close-packed phase transformation for a narrow range of wire diameters in the case of gold nanowires. Smaller nanowires and ligaments have a net effect of lowering the radiation damage as compared to larger wires that can be traced back to the fact that smaller nanowires transition from a rapid accumulation of defects to a saturation and annihilation mechanism at a lower dose than larger nanowires. These irradiation damage mechanisms are accompanied with radiation-induced surface roughening resulting from defect-surface interactions. Comparisons between nanowires and nanoporous structures show that the various mechanisms seen in nanowires provide adequate bounds for the defect accumulation mechanisms in nanoporous structures with the difference attributed to the role of nodes connecting ligaments in nanoporous structures. Altogether, our results shed light on the compounded, size-dependent mechanisms leading to the radiation resistance of nanowires and nanoporous structures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Charging-driven coarsening and melting of a colloidal nanoparticle monolayer at an ionic liquid–vacuum interface

In this work, we induce and investigate the coarsening and melting dynamics of an initially static nanoparticle colloidal monolayer at an ionic liquid–vacuum interface, driven by a focused, scanning electron beam. Coarsening occurs through grain interface migration and larger-scale motions such as grain rotations, often facilitated by sliding dislocations. The progressive decrease in area fraction that drives melting of the monolayer is explained using an electrowetting model whereby particles at the interface are solvated once their accumulating charge recruits sufficient counterions to subsume the particle. Subject to stochastic particle removal from the monolayer, melting is recapitulated in simulations with a Lennard-Jones potential. This new driving mechanism for colloidal systems, whose dynamical timescales we show can be controlled with the accelerating voltage, opens the possibility to manipulate particle interactions dynamically without need to vary particle intrinsic properties or surface treatments. Furthermore, the decrease in particle size availed by electron imaging presents opportunities to observe force and time scales in a lesser-explored regime intermediate between typical colloidal and molecular systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-Situ X-Ray Imaging High Strain Rate Compression of Laminate Al-Graphene Composite and Mechanical Property Characterization

Owing to the opaque nature of the laminated structures, traditional high-speed optical camera cannot be used to detect the dynamic process of sub-surface deformation. In this article, we report a study of using high speed X-ray imaging to study the high strain rate deformation in laminated Al structures. We used a Kolsky bar apparatus to apply dynamic compression and a high-speed synchrotron X-ray phase contrast imaging (PCI) setup to conduct the in situ X-ray imaging study. The in situ X-ray imaging captures the shock wave propagation in the laminated structures. After shock compression, we characterized the microstructures by using transmission electron microscopy (TEM), which demonstrates an increase of dislocation density. In conclusion, the micro-pillar compression tests show that the yield strength at 0.2% offset of laminated Al-graphene composite has a significant increase of 67%, from 30 to 50 MPa, compared to laminate Al after shock loading.

36 MATERIALS SCIENCE↗