Search NASA⌕ Search

SEARCH · Search NASA

Results for “TITANIUM OXIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Statistical fracture behavior of doped UO 2 using a ball-on-ring equibiaxial flexure test method

Metal oxide dopants, such as titanium and chromium oxides, have garnered considerable attention for their potential to increase grain size (≥ 30 µm) in UO 2 fuel, purportedly enhancing fission gas retention during reactor operation. Fuel performance is significantly impacted by fuel fracture behavior, so it is important to understand the effects of enhanced grain size and dopant content on UO 2 fuel fracture. UO 2 pellets were doped with 0.1 wt% TiO 2 and 0.3 wt% Cr 2 O 3 to alter density and grain size. Inductively coupled plasma mass spectroscopy measured dopant levels pre- and post-sintering. X-ray diffraction revealed lattice changes and microstrain via Rietveld refinement. Field emission scanning electron microscopy determined grain sizes of approximately 30 µm for TiO 2 doping and 7 µm for Cr 2 O 3 doping. Transverse rupture strength tests were performed on over 30 samples per dataset to obtain characteristic strength and Weibull modulus. Results indicate no statistical difference in fracture strength between 0.1 wt% TiO 2 doped UO 2 and undoped UO 2 , while 0.3 wt% Cr 2 O 3 doped UO 2 exhibited a 20% decrease in fracture strength. Doped UO 2 samples also showed reduced Weibull modulus compared to undoped UO 2 , suggesting increased scatter in fracture strength. This study's findings suggest that titanium and chromium oxide doping in UO 2 , regardless of grain size, induce residual stresses, decreasing fracture strength and increasing variability in fracture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Stability of Mn-Doped TiO 2 Thin-Film Anodes during Water Oxidation Reactions

Incorporating manganese atoms into TiO 2 has been shown to improve its activity for water oxidation. However, its activity has been observed to steadily degrade under constant applied potential, especially at more oxidizing applied potentials. Here, the compositional profile and electrochemical stability of Mn-doped TiO 2 (Mn:TiO 2 ) thin-film electrodes precisely fabricated by atomic layer deposition (ALD) were evaluated to elucidate the mechanisms of electrode degradation. Although ALD enables the deposition of Mn dopants throughout the film thickness, only Mn within 1.5 nm of the surface was observed to be redox active. Annealing Mn:TiO 2 films in air leads to the diffusion of Mn toward the electrode surface and oxidation of the Mn and alters the redox behavior. Annealing endows greater stability to Mn redox behavior but does not fully stabilize the water oxidation current, suggesting that the two electrochemical processes are not precisely correlated. In situ inductively coupled plasma mass spectrometry reveals that Mn is lost from Mn:TiO 2 films at potentials greater than 1.8 V vs RHE. However, the initial Mn loss is equivalent to less than a single ALD layer of MnO x . Longer-term constant potential experiments suggest that Mn is lost from up to 1 nm of the electrode surface but that this loss may account for only a portion of the diminished water oxidation activity.

atomic layer deposition↗
DOE OSTI2021

The effects of SMSI on m-Cresol Hydrodeoxygenation over Pt/Nb 2 O 5 and Pt/TiO 2

The hydrodeoxygenation (HDO) of m-cresol was studied on Pt/Nb 2 O 5 /MgAl 2 O 4 and Pt/TiO 2 /MgAl 2 O 4 catalysts to understand the effects of Strong Metal Support Interactions (SMSI). The Nb 2 O 5 and TiO 2 supports were prepared as 0.7-nm films on MgAl 2 O 4 by Atomic Layer Deposition (ALD) to ensure that the structures of the catalyst were the same. When reduced at 773 K to place Pt in the encapsulated state, Pt/Nb 2 O 5 /MgAl 2 O 4 was much less active than Pt/MgAl 2 O 4 at 573 K but much more active at 623 K. While Pt/MgAl 2 O 4 deactivated rapidly due to coking, Pt/Nb 2 O 5 /MgAl 2 O 4 showed significantly better coke tolerance and was almost 100% selective towards toluene production. Pt/Nb 2 O 5 /MgAl 2 O 4 reduced at lower temperatures exhibited intermediate catalytic properties. The effect of reduction temperature on Pt/TiO 2 /MgAl 2 O 4 was much less and this catalyst was more similar to Pt/MgAl 2 O 4 than its Nb 2 O 5 counterpart. Lastly, the implications of these results for understanding the nature of oxide promoters on HDO of m-cresol are discussed.

09 BIOMASS FUELS↗
NASA NTRS1998

An Infrared Spectroscopic and Density Functional Theoretical Investigation of the Reaction Products of Laser-Ablated Scandium and Titanium Atoms with Nitric Oxide

Laser-ablated Sc and Ti atoms have been reacted with NO during condensation in excess argon. Matrix infrared spectra show that the major products are the side bonded Sc[NO] species and the inserted NScO and NTiO molecules based on isotopic substitution (15NI6O and 15N18O) and DIFT calculations of isotopic frequencies, which provide a match for two modes in three isotopic modifications for each molecule. The NScO and NTiO molecules are nitride/oxides with M-O stretching modes only 46-88/cm below the diatomic metal oxides but M-N stretching modes 314-442/cm lower than the diatomic metal nitride molecules. The ScN, ScO, TiN, and TiO molecules are observed as decomposition products. Evidence is also presented for the nitrosyls ScNO and TiNO, the Sc[NO]+ cation, and the NTiO- anion.

Bauschlicher, Charles W., Jr.↗
NASA NTRS1999

Peroxide-modified titanium dioxide: a chemical analog of putative Martian soil oxidants

Hydrogen peroxide chemisorbed on titanium dioxide (peroxide-modified titanium dioxide) is investigated as a chemical analog to the putative soil oxidants responsible for the chemical reactivity seen in the Viking biology experiments. When peroxide-modified titanium dioxide (anatase) was exposed to a solution similar to the Viking labeled release (LR) experiment organic medium, CO2 gas was released into the sample cell headspace. Storage of these samples at 10 degrees C for 48 hr prior to exposure to organics resulted in a positive response while storage for 7 days did not. In the Viking LR experiment, storage of the Martian surface samples for 2 sols (approximately 49 hr) resulted in a positive response while storage for 141 sols essentially eliminated the initial rapid release of CO2. Heating the peroxide-modified titanium dioxide to 50 degrees C prior to exposure to organics resulted in a negative response. This is similar to, but not identical to, the Viking samples where heating to approximately 46 degrees C diminished the response by 54-80% and heating to 51.5 apparently eliminated the response. When exposed to water vapor, the peroxide-modified titanium dioxide samples release O2 in a manner similar to the release seen in the Viking gas exchange experiment (GEx). Reactivity is retained upon heating at 50 degrees C for three hours, distinguishing this active agent from the one responsible for the release of CO2 from aqueous organics. The release of CO2 by the peroxide-modified titanium dioxide is attributed to the decomposition of organics by outer-sphere peroxide complexes associated with surface hydroxyl groups, while the release of O2 upon humidification is attributed to more stable inner-sphere peroxide complexes associated with Ti4+ cations. Heating the peroxide-modified titanium dioxide to 145 degrees C inhibited the release of O2, while in the Viking experiments heating to this temperature diminished but did not eliminated the response. Although the thermal stability of the titanium-peroxide complexes in this work is lower than the stability seen in the Viking experiments, it is expected that similar types of complexes will form in titanium containing minerals other than anatase and the stability of these complexes will vary with surface hydroxylation and mineralogy.

Review↗
DOE OSTI2025

The Surface Chemistry of Methanol on TiO 2 (110): Effects of Pressure and Temperature on the Stability of C–O and C–H Bonds

Synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the surface chemistry of methanol on TiO 2 (110), examining the effects of methanol pressure, oxide temperature, and coadsorption with H 2 . At 300 K, the adsorption of methanol on TiO 2 (110) leads to the formation of CH 3 O on the surface with a minor amount of CH 3 OH present. The easy cleavage of the O–H bond in the alcohol agrees with the predictions of theoretical calculations, and most of the adsorbed CH 3 O was not associated with the presence of Ti 3+ sites in the oxide substrate. The adsorbed CH 3 O was removed from the TiO 2 (110) surface by heating to 600 K without the deposition of CH x fragments or C on the oxide. The results of temperature-programmed desorption (TPD) showed the evolution of methanol and formaldehyde at 360 and 490 K as a result of a disproportionation reaction: 2CH 3 O → CH 3 OH + CH 2 O. This surface chemistry, where there is no rupture of the C–O bond, and only selective cleavage of O–H and C–H bonds, is very different from that found on metals used in catalysts for methanol reforming, where massive conversion of the alcohol into CO, CH x and C species is seen. Furthermore, the TPD data indicate that any CH 3 O formed on the oxide surface can be hydrogenated and desorbed as CH 3 OH at temperatures below 550 K. In this respect, titania is an ideal support for catalysts employed to achieve methanol synthesis through CO 2 hydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Specific features of fluorescence transfer in multiply scattering randomly inhomogeneous layers under intense laser pumping

Based on the analysis of experimental data on the effect of the pulsed laser pump intensity on the spectral properties and the size of the fluorescent response zone in randomly inhomogeneous fluorescent layers, we found that the amplification of spontaneous and stimulated emission significantly affects the statistical properties of the propagation lengths of the fluorescent field partial components in the layers. The experiments are performed with layers of SiO{sub 2} and TiO{sub 2} nanoparticles saturated with rhodamine 6G, pumped by 532-nm laser radiation in the intensity range corresponding to the transient regime from excitation of spontaneous fluorescence to random lasing in the layer. The experimental data are compared with the results of statistical modelling of fluorescence transfer. It is shown that, even at a pump intensity below the random lasing threshold, the spontaneous emission amplification in a layer leads to a significant increase in the contributions to the fluorescence response from partial components with propagation lengths much larger than the layer thickness. This can be interpreted as a manifestation of the quasi-waveguide effect, in which the probability of propagation of diffuse fluorescence components along the layer over distances many times greater than its thickness and the size of the pumped region increases significantly with a decrease in the characteristic radiation amplification length in the layer. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Self-Cleaning Highly Porous TiO 2 Coating Designed by Swelling-Assisted Sequential Infiltration Synthesis (SIS) of a Block Copolymer Template

Photocatalytic self-cleaning coatings with a high surface area are important for a wide range of applications, including optical coatings, solar panels, mirrors, etc. Here, we designed a highly porous TiO 2 coating with photoinduced self-cleaning characteristics and very high hydrophilicity. This was achieved using the swelling-assisted sequential infiltration synthesis (SIS) of a block copolymer (BCP) template, which was followed by polymer removal via oxidative thermal annealing. The quartz crystal microbalance (QCM) was employed to optimize the infiltration process by estimating the mass of material infiltrated into the polymer template as a function of the number of SIS cycles. This adopted swelling-assisted SIS approach resulted in a smooth uniform TiO 2 film with an interconnected network of pores. The synthesized film exhibited good crystallinity in the anatase phase. The resulting nanoporous TiO 2 coatings were tested for their functional characteristics. Exposure to UV irradiation for 1 h induced an improvement in the hydrophilicity of coatings with wetting angle reducing to unmeasurable values upon contact with water droplets. Furthermore, their self-cleaning characteristics were tested by measuring the photocatalytic degradation of methylene blue (MB). The synthesized porous TiO 2 nanostructures displayed promising photocatalytic activity, demonstrating the degradation of approximately 92% of MB after 180 min under ultraviolet (UV) light irradiation. Thus, the level of performance was comparable to the photoactivity of commercial anatase TiO 2 nanoparticles of the same quantity. Our results highlight a new robust approach for designing hydrophilic self-cleaning coatings with controlled porosity and composition.

36 MATERIALS SCIENCE↗
NASA NTRS1962

Titanium-Oxygen Reactivity Study

A program has been conducted at Astronautics to investigate the likelihood of occurrence of the catastrophic oxidation of titanium alloy sheet under conditions which simulate certain cases of accidental failure of the metal while it is in contact with liquid or gaseous oxygen. Three methods of fracturing the metal were used; they consisted of mechanical puncture, tensile fracture of welded joints, and perforation by very high velocity particles. The results of the tests which have been conducted provide further evidence of the reactivity of titanium with liquid and gaseous oxygen. The evidence indicates that the rapid fracturing of titanium sheet while it is in contact with oxygen initiates the catastrophic oxidation reaction. Initiation occurred when the speed of the fracture was some few feet per second, as in both the drop-weight puncture tests and the static tensile fracture tests of welded joints, as well as when the speed was several thousand feet per second, as in the simulated micrometeoroid penetration tests. The slow propagation of a crack, however, did not initiate the reaction. It may logically be concluded that the localized frictional heat of rapid fracture and/or spontaneous oxidation (exothermic) of minute particles emanating from the fracture cause initiation of the reaction. Under conditions of slow fracture, however, the small heat generated may be adequately dissipated and the reaction is not initiated. A portion of the study conducted consisted of investigating various means by which the reaction might be retarded or prevented. Providing a "barrier" at the titanium-oxygen interface consisting of either aluminum metal or a coating of a petroleum base corrosion inhibitor appeared to be only partially effective in retarding the reaction. The accidental puncturing or similar rupturing of thin-walled pressurized oxygen tanks on missiles and space vehicle will usually constitute loss of function, and may sometimes cause their catastrophic destruction by explosive decompression regardless of the type of material used for their construction. In the case of tanks constructed of titanium alloys the added risk is incurred of catastrophic burning of the tanks. In view of this it is recommended that thin-walled tanks constructed of titanium alloys should not be used to contain liquid or gaseous oxygen.

Chafey, J. E.↗
NASA NTRS1996

The Oxidation and Protection of Gamma Titanium Aluminides

The excellent density-specific properties of the gamma class of titanium aluminides make them attractive for intermediate-temperature (600-850 C) aerospace applications. The oxidation and embrittlement resistance of these alloys is superior to that of the alpha(sub 2) and orthorhombic classes of titanium aluminides. However, since gamma alloys form an intermixed Al2O3/TiO2 scale in air rather than the desired continuous Al2O3 scale, oxidation resistance is inadequate at the high end of this temperature range (i.e., greater than 750-800 C). For applications at such temperatures, an oxidation-resistant coating will be needed; however, a major drawback of the oxidation-resistant coatings currently available is severe degradation in fatigue life by the coating. A new class of oxidation-resistant coatings based in the Ti-Al-Cr system offers the potential for improved fatigue life.

Brady, Michael P.↗
DOE OSTI2024

Review of Solid State Consolidation Processing Techniques of ODS Steels (Hot Extrusion, Hot Isostatic Pressing, Spark Plasma Sintering, and Stir Friction Consolidation): Resulting Microstructures and Mechanical Properties

This paper reviews the solid-state consolidation processing techniques for Oxide Dispersion Strengthened steels and compares them in terms of the resulting microstructure and reported mechanical properties. Synthesis techniques include hot extrusion, hot isostatic pressing, spark plasma sintering and friction consolidation. The effects of process parameters on the resulting microstructures and performance are discussed for each technique. Average oxide size, average grain size, and porosity are compared across techniques, as well as mechanical strength and ductility. Across consolidation techniques where temperature can be controlled, a low sintering temperature with a high sintering pressure is favorable for keeping oxide sizes, grain sizes, and porosity low. The use of yttrium and titanium for oxide formation has been evidenced to reduce oxide sizes, and tungsten additions have been shown to improve strength. Current literature suggests that the more mature hot extrusion technique produces stronger steel with consistently fine oxides, while other alternative solid-state consolidation, while promising, offer margin for improvement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Hubble PanCET Program: Transit and Eclipse Spectroscopy of the Strongly Irradiated Giant Exoplanet WASP-76b

Ultra-hot Jupiters with equilibrium temperatures greater than 2000 K are uniquely interesting targets as they provide us crucial insights into how atmospheres behave under extreme conditions. This class of giant planets receives intense radiation from their host star and usually has strongly irradiated and highly inflated atmospheres. At such a high temperature, cloud formation is expected to be suppressed and thermal dissociation of water vapor could occur. We observed the ultra-hot Jupiter WASP-76b with seven transits and five eclipses using the Hubble Space Telescope and the Spitzer Space Telescope (Spitzer) for a comprehensive study of its atmospheric chemical and physical processes. We detected TiO and H{sub 2}O absorption in the optical and near-infrared transit spectrum. Additional absorption by a number of neutral and ionized heavy metals like Fe, Ni, Ti, and SiO help explain the short-wavelength transit spectrum. The secondary eclipse spectrum shows muted water feature but a strong CO emission feature in Spitzer’s 4.5 μm band indicating an inverted temperature pressure profile. We analyzed both the transit and eclipse spectra with a combination of self-consistent PHOENIX models and atmospheric retrieval. Both spectra were well fitted by the self-consistent PHOENIX forward atmosphere model in chemical and radiative equilibrium at solar metallicity, adding to the growing evidence that both TiO/VO and NUV heavy metals opacity are prominent NUV-optical opacity sources in the stratospheres of ultra-hot Jupiters.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

NOx sequestration by calcium aluminate cementitious materials

This study quantifies NO{sub x} uptake efficiency and explores NO{sub x} binding mechanisms in calcium aluminate cementitious (CAC) materials. Comparison between unmodified and TiO{sub 2}-modified CAC separates intrinsic NO{sub x} binding mechanisms from those related to photocatalysis. Attributed to surface-related heterogeneous reactions, the NO{sub x} binding occurs in unmodified CAC at nitrite-to-nitrate ratio of 1: 1.3 and can be increased with surface area. The photocatalytic reactions in TiO{sub 2}-modified CAC increase NO{sub x} uptake, and ~50% of converted NO{sub x} resists releasing back into the environment via dissolution. Compared to previously studied ordinary portland cement (OPC) materials, CAC increases NO{sub x} uptake capacity and demonstrates a more permanent NO{sub x} binding, potentially mitigating concerns related to the release of previously bound N-species in OPC. Examination of the interaction between NO{sub x} and a synthetic pure aluminum-bearing phase shows that the permanent NO{sub x} uptake in CAC could be largely attributed to the chemical binding of converted NO{sub x} within aluminum-bearing phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Interface Carriers and Enhanced Electron-Phonon Coupling Effect in Al 2 O 3 /TiO 2 Heterostructure Revealed by Resonant Inelastic Soft X-Ray Scattering

The electronic structure and the electron-phonon couplings in a novel mass-production-compatible Al 2 O 3 /TiO 2 2D electron system (2DES) are investigated using resonant inelastic soft X-ray scattering. The experimental data from the samples of various TiO 2 thicknesses unequivocally show that the Ti 3+ state indeed exists at the deep interface to serve as an n-type dopant for the 2DES. Here, the electronic structure of Ti 3+ species is scrutinized as entirely separated from that of the Ti 4+ host lattice. Furthermore, features of sub-eV energy loss phonon modes are clearly observed, indicating substantial electron-phonon coupling effects. Such low energy loss features are enhanced in thinner TiO 2 samples, implying that polaronic local lattice deformation is enhanced due to the presence of Ti 3+ . These findings suggest that the 2DES properties can be controlled via well-established TiO 2 engineering, thereby enthroning the binary oxide heterostructure as a promising candidate for 2DES device applications.

2D electron gas↗
NASA NTRS2014

Novel Materials, Processing and Device Technologies for Space Exploration with Potential Dual-Use Applications

We highlight results of a broad spectrum of efforts on lower-temperature processing of nanomaterials, novel approaches to energy conversion, and environmentally rugged devices. Solution-processed quantum dots of copper indium chalcogenide semiconductors and multiwalled carbon nanotubes from lower-temperature spray pyrolysis are enabled by novel (precursor) chemistry. Metal-doped zinc oxide (ZnO) nanostructured components of photovoltaic cells have been grown in solution at low temperature on a conductive indium tin oxide substrate. Arrays of ZnO nanorods can be templated and decorated with various semiconductor and metallic nanoparticles. Utilizing ZnO in a more broadly defined energy conversion sense as photocatalysts, unwanted organic waste materials can potentially be repurposed. Current efforts on charge carrier dynamics in nanoscale electrode architectures used in photoelectrochemical cells for generating solar electricity and fuels are described. The objective is to develop oxide nanowire-based electrode architectures that exhibit improved charge separation, charge collection and allow for efficient light absorption. Investigation of the charge carrier transport and recombination properties of the electrodes will aid in the understanding of how nanowire architectures improve performance of electrodes for dye-sensitized solar cells. Nanomaterials can be incorporated in a number of advanced higher-performance (i.e. mass specific power) photovoltaic arrays. Advanced technologies for the deposition of 4H-silicon carbide are described. The use of novel precursors, advanced processing, and process studies, including modeling are discussed from the perspective of enhancing the performance of this promising material for enabling technologies such as solar electric propulsion. Potential impact(s) of these technologies for a variety of aerospace applications are highlighted throughout. Finally, examples are given of technologies with potential spin-offs for dual-use or terrestrial applications.

solid state devices↗
DOE OSTI2026

Sequential surface synthesis of dispersed sub-nanometer iridium on titanium nitride for acidic water oxidation

Maximizing iridium utilization while maintaining high oxygen evolution reaction (OER) performance remains a persistent challenge in acidic water electrolysis. Immobilizing Ir on conductive, acid-stable supports is promising, yet simultaneously achieving sub-nanometer size, high area coverage, and strong electronic coupling is difficult. Here, we report a sequential surface synthesis on titanium nitride (TiN) that yields uniformly distributed sub-nanometer Ir arrays (∼0.7 nm). Our method uses ethylenediaminetetraacetic acid (EDTA) as a temporal scaffold: it chemisorbs to TiN to install dense chelating sites, captures Ir 3+ ions, and confines Ir cluster growth. A subsequent thermal treatment at 500 °C in a reducing atmosphere removes the ligand shell, while preserving ultrasmall particle size and establishing direct Ir–TiN electronic coupling. The optimized catalyst exhibits mixed Ir 0 /Ir x+ coordination with low charge-transfer resistance (R ct = 19.2 Ω), delivering a mass activity of 342 A g Ir −1 at 1.54 V in acidic electrolyte. In situ X-ray absorption spectroscopy reveals irreversible surface oxidation as the primary stability-limiting factor. This stepwise strategy provides a general framework for supported catalysts that maximize precious metal utilization via sub-nanometer dispersion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗