Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermoplasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Increasing Z-Strength and Testing the Capabilities of Twin Screw Extruders in Large Format Polymer Additive Manufacturing

During the first phase of this project, small and large Strangpresse extruders were assessed at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility (MDF). This phase resulted in Strangpresse exclusively licensing some of ORNL’s previously developed extruder technology for high-volume thermoplastic additive manufacturing (AM). Phase II of this project will focus on further development and optimization of Strangpresse extruders for increased efficiency and increased throughput. The objective of this project is to develop a new extruder with a higher output and less energy usage than current AM thermoplastic extruders and to develop and evaluate a new tamper mechanism for increasing Z-strength resulting in an advanced and optimized extruder and tamper system.

42 ENGINEERING↗
DOE OSTI2022

Nitrile-Containing Renewable Polymers Based on Lignin, (CRADA) No. NFE 1807437 (CRADA Final Report)

Lignin remains one of the world’s largest sources of renewable carbon, with significant potential to positively impact our carbon footprint by replacing fossil-fuel derived materials, including engineering thermoplastics and their composites. Efforts to incorporate significant quantity of lignin into engineering thermoplastics as anything other than an inert filler have to date been largely unsuccessful, however due to limitations imposed by the degradation temperature of the lignin (220 °C) and poor compatibility between the lignin and non-polar or slightly polar polymers. Recent work at Oak Ridge National Laboratory has however shown under the right conditions excellent compatibility between lignin and nitrile containing rubber compounds such as nitrile-butadiene rubber (NBR). The present work extends these findings to the incorporation of lignin into acrylonitrile-butadiene-styrene (ABS) engineering plastics. While simple binary mixing of lignin into commercial ABS resins leads to poor interfacial adhesion and resultant low toughness and ductility, appropriate matching of the lignin and ABS components, and as appropriate compatibilizing agents, leads to polymer blends incorporating 20-35% by weight lignin with a useful range of mechanical properties for many current ABS applications. By modifying the composition, the balance of properties can be readily tailored to meet the demands of specific end-user applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

CRADA Number NFE-20-08283 with Actinic LLC (CRADA Final Report)

Significant advances have been made in the additive manufacturing (AM) of thermoplastics and optically cured thermosets; however, AM of thermally cured thermosets has lagged. Materials belonging to this class of thermosets, such as silicone rubbers and polyurethanes, are not well represented in the AM space despite their widespread use in medical, defense, and other fields. Ideally, a solution would enable AM of current commercially viable thermally cured thermosets with a speed that is comparable to those already realized for thermoplastics and optically cured thermosets. Realizing this goal will provide several benefits, including: 1. Make thermally cured thermoset designs impossible via casting. 2. Iteration of part designs without investment in new molds. 3. Devices and personal protection equipment, custom-fit to the end-user. 4. Ability to print multifunctional composite materials. 5. Rapid production ability for DoD personnel deployed at forward locations. 6. Simplify supply chains and replace multiple parts with a single raw material. These benefits motivate the development of a commercially viable 3D printer for thermally cured thermosets, based on the technique of photothermal curing. This project further developed a printer capable of printing composites containing commercially available thermally cured polydimethylsiloxane (PDMS), directly yielding cured parts such as boxes, walls, and free-standing overhangs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Coal-based Bricks & Blocks (CBBs): Process Development to Prototype Fabrication Coupled with Techno-Economic Analysis and Market Survey

Coal-based bricks and blocks (CBBs) were formulated using anthracite and thermoplastic binder. Lab scale test composites were formed by hot-press molding and commercial extrusion for test articles and for a full-scale prototype. Formulations and test matrices followed a systematic experimental design to examine the effects of and interactions among three primary independent variables: a) thermoplastic type, b) weight fractions of binder relative to the total anthracite weight, and c) relative proportions of large versus small (milled) anthracite size fractions. Technical performance metrics include compressive strength, modulus, porosity/permeability and density. These DoE studies establish composition-property relations and identify the best combination for any desired property of interest – in particular, strength. Based on CBB composition and fabrication process, validated against technical performance metrics, a techno-economic analysis was constructed which incorporated a process flow model, engineering design (with scaling), and calculated capital plus operating costs. Based on measured property metrics and estimated process economics and a projected price by TEA (techno-economic analysis), building and construction target markets were identified by a market survey assessment. With known cost, price, performance metrics and competitive advantages for CBBs matched with commercial applications/uses, a technical gap analysis was performed to identify further development required for scale-up and commercialization.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Using low cost, bio-derived and recycled materials in advanced scalable small- and medium- wind turbine manufacturing

In partnership with Bergey Windpower, this project explored the use of recyclable and recycled materials in small- to medium-wind turbine blades (WTBs). A recyclable epoxy resin and infusible thermoplastic resin were investigated using identical fiber reinforcements and manufacturing practices used as Bergey, and the substitution of continuous virgin glass fiber (GF) layers with recycled nonwoven GF (rGF, NW) mats was trialed. The alternative resins both showed very promising performance in terms of static tensile and flexural behavior as well as thermal properties and fatigue behavior in comparison with that of the incumbent materials used at Bergey. The NW rGF materials, however, were found to be a poor substitute for the continuous GF materials for two primary reasons. Firstly, the NW mats took up significantly more resin than their continuous counterparts, which would increase both the weight and the cost of the WTBs. Additionally, an unexpected reaction occurred between the rGF and epoxy materials that resulted in a highly porous, foamed structure. The foaming phenomenon was not observed with the rGF NW and infusible thermoplastic material, but the resin uptake was still prohibitively high. Based on the results of this study, recyclable infusible resins could be viable candidate materials for Bergey in the future. The foaming reaction with the rGF NW mats could prove highly useful in other applications requiring structural foams and has been used to produce demonstrative sandwich panels.

17 WIND ENERGY↗
DOE OSTI2020

Investigating Core Gaps and the Development of Subcomponent Validation Methods for Wind Turbine Blades: Preprint

Core gaps are a common manufacturing defect observed in wind blade composite sandwich constructions, which occur when sheets of core material are not properly butted up against each other in the mold. The aim of this study was to characterize core gaps in composite sandwich constructions at the coupon scale. This was to gain an initial understanding of the defect before developing appropriate methodologies for more complex subcomponents as part of a much broader wind blade structural validation and damage tolerance program. Long beam flexure in 4-point-bending was chosen as the most appropriate loading scenario. Beam specimens were characterized with and without 10 mm core gaps in fiberglass/balsa sandwich beams. The core gaps were characterized with two separate resin systems; a Hexion epoxy and Arkema's Elium resins system (a novel, infusible thermoplastic). Results showed that the Elium beams without the core gaps were had a 15% lower static strength than their epoxy counterparts. The introduction of the core gap to the epoxy beams reduced their static strength by 35%. The Elium beams, however, exhibited negligible strength reductions with the inclusion of the core gap. Overall, this characterization study provided pertinent information with regards to core gaps as a manufacturing defect to allow for continued development of damage tolerance and subcomponent validation methodologies with the inclusion of manufacturing defects.

17 WIND ENERGY↗
DOE OSTI2026

Additively Reinforced Thermoformable PETG Composite Sheets for Improved Structural Efficiency

Thermoforming of short-fiber reinforced thermoplastic sheets offers a viable pathway for producing lightweight composite components; however, inherent anisotropy in fiber-reinforced sheets can limit structural performance under multidirectional loading. In this work, short carbon fiber, glass fiber, and hybrid fiber–reinforced PETG sheets were evaluated as candidate feedstock materials for thermoforming, with flexural and tensile testing performed both along the primary fiber direction and in the off-axis orientation to establish baseline stiffness, strength, and anisotropy. As expected, short carbon fiber PETG exhibited the highest stiffness and strength in the primary fiber direction, while all systems showed reduced performance in the off-axis direction. This off-axis performance reduction provides clear justification for the use of additive reinforcement when such thermoformed sheets are intended for structural applications. The intended manufacturing sequence involves thermoforming the reinforced sheet first, followed by the application of additively manufactured lattice reinforcement; therefore, the reinforcement strategy does not impose limitations on sheet formability during thermoforming. Post-forming lattice reinforcement significantly reduced load-normalized displacement by approximately 95–99% relative to non-reinforced sheets and improved weight-normalized stiffness by ~70%. These findings demonstrate that geometry-driven additive reinforcement can effectively compensate for off-axis property reductions in thermoformed PETG composites, enabling enhanced multidirectional structural performance without compromising manufacturability.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗
DOE OSTI2024

Testing Protocol Development for the Fracture Toughness of Parts Built with Big Area Additive Manufacturing

The mechanical testing of additively manufactured parts has largely relied on the existing standards developed for traditional manufacturing. While this approach leverages the investment made in current standards development, it inaccurately assumes that the mechanical response of additive manufacturing (AM) parts is identical to that of parts manufactured through traditional processes. When considering thermoplastic, material extrusion AM, the differences in response can be attributed to an AM part’s inherent inhomogeneity caused by porosity, interlayer zones, and surface texture. Additionally, the interlayer bonding of parts printed with large-scale AM is difficult to adequately assess, as much testing is performed such that stress is distributed across many layer interfaces; therefore, the lack of AM-specific standards to assess interlayer bonding is a significant research gap. To quantify interlayer bonding via fracture toughness, double cantilever beam (DCB) testing has been used for some AM materials, and DCB has been generally used for a variety of materials including metal, wood, and laminates. Mode I DCB testing was performed on thermoplastic matrix composites printed with Big Area Additive Manufacturing (BAAM). Of particular interest was the notch shape and deflection speed during testing. The results examine the differences when using two notch types and three deflection speeds. The testing method introduced by the following paper differentiates itself from the ones described in the standards used by modernizing the methodology. This was conducted with the introduction of Digital Image Correlation (DIC) to gather displacement and load data simultaneously without human intervention.

Polymer Science↗
DOE OSTI2022

MODELLING FIBER ORIENTATION DURING ADDITIVE MANUFACTURING COMPRESSION MOLDING PROCESSES

The production of high-performance thermoplastic composites reinforced with short carbon fibers can be achieved by a novel “additive manufacturing-compression molding” technique. An advantage of such combination is two-fold: controlled fiber orientation in additive manufacturing and less void content by compression molding. In this study, a computational fluid dynamics model has been developed to predict the behavior of printed layers during fiber-reinforced thermoplastic extrusion and subsequent compression molding. The fiber orientation was modelled with a simple quadratic closure model. The interaction between the fibers is included using a rotary diffusion coefficient which becomes significant in concentrated regimes. Finally, the second order orientation tensor is coupled with the momentum equation as an anisotropic part of the stress term. The effect of processing parameters on the behavior of printed layers was investigated to determine the favorable printing scenarios. The developed numerical model enables design of high-performance composites with tunable mechanical properties.

Seta, Berin↗
DOE OSTI2022

Additive manufacturing method and assembly

Methods and assemblies for additive manufacturing portions of components with enhanced strength are provided. The assemblies comprise a first deposition head and an apparatus for causing one or more reinforcement fibers to extend more than two layers within previously-deposited layers of build material. The first deposition head is configured to deposit a plurality of layers of a filament comprising a reinforcement fiber and thermoplastic material. The apparatus may comprise a needle point configured to be inserted into the plurality of layers to displace the reinforcement fiber so that it extends two or more of the plurality of layers. The apparatus may additionally or alternatively comprise a second deposition head having a needle tip configured to be inserted into the plurality of layers to inject a length of a second filament comprising thermoplastic material and a reinforcement fiber so that the reinforcement fiber of the second filament extends two or more layers of the plurality of layers of the first filament.

Barr, Christian G.↗
DOE OSTI2022

All-acrylic multigraft copolymer superelastomers

Thermoplastic elastomer compositions comprising acrylic multigraft copolymers are described. The multigraft copolymers comprise a rubbery polyacrylate backbone and a plurality of randomly spaced glassy polyacrylate side chains. The multigraft copolymers can be prepared using a facile grafting through method that can provide copolymers with enhanced purity. The acrylic multigraft copolymers exhibit microphase separated morphologies and “superelastomeric” properties, including an elongation at break, stress at break, and/or strain recovery behavior that exceeds that of conventional triblock copolymer polyacrylate thermoplastic elastomers.

Mays, Jimmy W.↗
DOE OSTI2023

High resolution and high flexibility fiber optical cables and microfabrication methods for making same

The present disclosure relates to methods of forming a fiber optic core, and a fiber optic component with a highly uniform cladding covering the fiber optic core. In one microfabrication process a first sacrificial tubing is provided which has a predetermined inner diameter. A quantity of a curable polymer is also provided. The first sacrificial tubing is at least partially filled with the curable polymer. The curable polymer is then cured. The first sacrificial tubing is then removed to produce a finished fiber optic core. Additional operations may be performed by which the fiber optic core is placed inside a thermoplastic tubing, which is itself placed inside a sacrificial heat shrink. Heat is applied to reflow the thermoplastic tubing around the fiber optic core, thus forming a highly uniform thickness cladding. When the sacrificial heat shrink tubing is removed a finished fiber optic component is present. Additional microfabrication methods are disclosed which involve dip coating a pre-formed fiber optic core in a polymer, and then curing the polymer to form a finished fiber optic component with a uniform thickness cladding.

Kampasi, Komal↗
DOE OSTI2023

Wind Turbine Blade Repurposing and Recycling: Coupling Repurposing Methods with 3D Printing Technology

Fiber-reinforced thermoplastic composites continue to be implemented in several marketsbecause of their strength capacity and light weight. Especially in the wind industry, wind bladesare made of this material which makes them ideal for wind energy generation, but bladesbecome a problem at end-of-life. Because recycling thermoplastic composites technologiesare still not cost and environmentally effective, research in this space is needed. This paperpresents a case study for coupling repurposed wind turbine blades and 3D printing technology.The purpose is to remanufacture decommissioned wind blades into bus stop roof and seatingsections to then use recycled glass fiber from a decommissioned wind turbine blade to 3Dprint structural and/or fixtures needed in the assembly. We provide an overview of the designprocess, and the development process steps in repurposing and 3D printing the material,delving into key parameters required for a successful implementation.

Henao, Yulizza↗
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2020

Post-process annealing of large-scale 3D printed polyphenylene sulfide composites

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced joining strength in additive-manufactured polylactic-acid structures fused by embedded heated metallic meshes

Additively manufactured thermoplastic polymers, such as polylactic acid (PLA), hold significant promise for sustainable engineering structures, including wind turbine blades. Upscaling these structures beyond the limitations of 3D printer build volumes is a challenge; fusion joining presents a potential solution. This paper introduces a displacement-controlled resistance welding process for PLA, as an alternative to the typical force-controlled methods. Here, we investigated the bonding quality of resistance-welded and adhesive-bonded PLA beams through three-point bending and measured the surface deformations using digital image correlation. Different metal meshes (30%/0.11 mm Ni—Cu, 34%/0.07 mm Ni—Cu, and 36%/0.25 mm Co—Ni) served as heating elements. The process parameters were varied for the 34%/0.07 mm Ni—Cu mesh to identify an optimum set of parameters. Results showed that this optimized displacement-controlled welding achieved 94% of the original strength of monolithic samples. This indicates that the new welding process not only ensures high-quality bonding and fine surface finishing but also promotes sustainability, recyclability, and economic efficiency in various polymer and composite structural applications.

Additive manufacturing↗