Results for “flow direction” — Page 10

NASA NTRS1983

Constant-temperature hot-wire anemometer practice in supersonic flows. II - The inclined wire

The performance of a constant-temperature inclined hot-wire in a supersonic flow is critically examined. It is shown that calibration techniques applicable to subsonic flow, such as the cosine cooling law cannot be used when the flow is supersonic. Calibration and measurement procedures appropriate to supersonic flow are suggested, together with the possible limits on their validity. Experimental results for different wires indicate that the sensitivities do not seem to depend on flow direction according to any simple correlation. When the sensitivity exhibits a strong dependence on flow direction, the wire should be discarded to avoid errors due to nonlinear effects.

Smits, A. J.↗

NASA NTRS1982

A hydrodynamic model of an outer hair cell

On the model it is possible to measure the force and the force direction for each individual hair as a function of the flow direction and velocity. Measurements were made at the man flow velocity .01 m/s, which is equivalent to a flow velocity in the real ear of about 1 micrometer/s. The kinematic viscosity of the liquid used in the model was 10,000 times higher than the viscosity of perilymph to attain hydrodynamic equality. Two different geometries for the sterocilia pattern were tested. First the force distribution for a W-shaped sterocilia pattern was recorded. This is the sterocilia pattern found in all real ears. It is found that the forces acting on the hairs are very regular and perpendicular to the legs of the W when the flow is directed from the outside of the W. When the flow is reversed, the forces are not reversed, but are much more irregular. This can eventually explain the half wave rectification of the nerve signals. As a second experiment, the force distribution for a V-shaped sterocilia pattern was recorded. Here the forces were irregular both when the flow was directed into the V and when it was directed against the edge of the V.

Jacobson, B. O.↗

NASA NTRS1998

Virtual and Experimental Visualization of Flows in Packed Beds of Spheres Simulating Porous Media Flows

A videotape presentation of flow in a packed bed of spheres is provided. The flow experiment consisted of three principal elements: (1) an oil tunnel 76.2 mm by 76.2 mm in cross section, (2) a packed bed of spheres in regular and irregular arrays, and (3) a flow characterization methodology, either (a) full flow field tracking (FFFT) or (b) computational fluid dynamic (CFD) simulation. The refraction indices of the oil and the test array of spheres were closely matched, and the flow was seeded with aluminum oxide particles. Planar laser light provided a two-dimensional projection of the flow field, and a traverse simulated a three-dimensional image of the entire flow field. Light focusing and reflection rendered the spheres black, permitting visualization of the planar circular interfaces in both the axial and transverse directions. Flows were observed near the wall-sphere interface and within the set of spheres. The CFD model required that a representative section of a packed bed be formed and gridded, enclosing and cutting six spheres so that symmetry conditions could be imposed at all cross-boundaries. Simulations had to be made with the flow direction at right angles to that used in the experiments, however, to take advantage of flow symmetry. Careful attention to detail was required for proper gridding. The flow field was three-dimensional and complex to describe, yet the most prominent finding was flow threads, as computed in the representative 'cube' of spheres with face symmetry and conclusively demonstrated experimentally herein. Random packing and bed voids tended to disrupt the laminar flow, creating vortices.

Hendricks, R. C.↗

DOE OSTI2024

Simultaneous analysis of collinear neutron time-of-flight (nToF) traces applied to pulsed fusion experiment

On pulsed fusion experiments, the neutron time of flight (nToF) diagnostic provides critical information on the fusion neutron energy spectrum. This work presents an analysis technique that uses two collinear nToF detectors, potentially to measure nuclear bang time and directional flow velocities. Two collinear detectors may be sufficient to disambiguate the contributions of nuclear bang time and directional flow velocities to the first moment of the neutron energy spectrum, providing an independent measurement of nuclear bang time. In conclusion, preliminary results from measured nToF traces on the National Ignition Facility and additional applications of this technique are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1986

Magnetic configurations of planetary obstacles

The interaction between planetary magnetospheres and solar wind flow is discussed. A proper planetary magnetosphere results from the interaction of a flowing plasma with a planet having an intrinsic, global, magnetic field of sufficient strength to stand off the impinging plasma. Upstream of such an obstacle a bow shock usually exists. The known magnetospheres have severely asymmetric shapes, being elongated approximately along the solar wind flow direction. Conditions which fundamentally determine the structure of a proper planetary magnetosphere are the state of the externally flowing plasma, the planet's magnetic moment, its vector spin, and the presence and nature of internal plasma sources and any plasma sinks. Planets known to have proper magnetospheres are Earth, Mercury, Jupiter, and Saturn. Uranus and Neptune may also have magnetospheres, with that of Uranus promising to have an exotic field configuration, because the planet's magnetic moment is expected to be nearly aligned with the solar wind flow direction. Venus and Mars are also discussed. Magnetopause surface waves are mentioned.

Lepping, R. P.↗

DOE OSTI2022

Onset of instabilities in rotating flows by direct numerical simulation

A rotating disk is the canonical experiment for measuring surface reaction rates in geochemical and electrochemical systems. Using the similarity solution for laminar flow around an infinite disk, the mass transfer coefficient can be simply related to the intrinsic reaction rate at the surface. However, measurements of mass transfer rates use a finite-size disk within a larger container of solution; here the flow is no longer strictly laminar, but there must always be some recirculation. Our interest was initially in the assumption of a uniform radial concentration field, how this breaks down near the perimeter of the disk, and what effect that might have on the measured mass transfer rates. However, our numerical simulations suggest that the flow around a finite-size disk becomes time dependent at Reynolds number ($\textit{Re}$) below 1000, which is much smaller than the typical values in mass-transfer measurements ($\textit{Re}$~10 4 ). In this work, we observe the formation of coherent structures in the flow, which suggest a non-uniform mass transfer at the disk surface. The rotating-disk flow follows a similar sequence of instabilities to the Taylor–Couette flow: a centrifugal instability leading an axisymmetric, time-invariant flow, followed by a Hopf bifurcation to a time-periodic flow. To minimise the possibility that our results are a numerical artefact, we have also simulated the instability in the stationary boundary layer of a rotor–stator flow, comparing with self-similar solutions at low $\textit{Re}$ and with spectral methods near the critical Reynolds number.

42 ENGINEERING↗

DOE OSTI2025

Development of fiber orientation in injection molding: Comparison of glass fiber, carbon fiber and their hybrid composites

Fiber orientation distribution (FOD) in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for glass fiber (GF), carbon fiber (CF), and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varied with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗

NASA NTRS1975

Acoustics of attached and partially attached flow for simplified OTW configurations with 5:1 slot nozzle

The acoustics of simple engine over-the-wing configurations, with complete and partially attached jet flow to the shielding surface, were studied at model scale. The nozzle consisted of a 5:1 slot nozzle operated at a nominal jet Mach number of 0.6, with the flow directed parallel to and at angles up to 10 deg toward the shielding surface. The shielding length of the surface and the nozzle height above the surface were varied. The aerodynamic results indicate that, with attached flow, the jet flow field is stretched in the flow direction resulting in locally higher velocities than those for partially attached flow or nozzle only flow. The stretching of the flow field increased the noise levels for the attached flow cases compared to those with only partially attached flow. With attached flow, the shielding benefits were substantially reduced compared with fully detached flow. Increasing the impingement angle of the jet flow from 0 to 10 deg generally caused the noise levels to increase in the mid and high frequencies.

Von Glahn, U.↗

NASA NTRS1986

Boundary layer flow visualization for flight testing

Flow visualization is used extensively in flight testing to determine aerodynamic characteristics such as surface flow direction and boundary layer state. Several visualization techniques are available to the aerodynamicist. Two of the most popular are oil flows and sublimating chemicals. Oil is used to visualize boundary layer transition, shock wave location, regions of separated flow, and surface flow direction. Boundary layer transition can also be visualized with sublimating chemicals. A summary of these two techniques is discussed, and the use of sublimating chemicals is examined in some detail. The different modes of boundary layer transition are characterized by different patterns in the sublimating chemical coating. The discussion includes interpretation of these chemical patterns and the temperature and velocity operating limitations of the chemical substances. Information for selection of appropriate chemicals for a desired set of flight conditions is provided.

Obara, Clifford J.↗

DOE OSTI2022

MERIT-Plus Dataset: Delineation of endorheic basins in 5 and 15 min upscaled river networks

Endorheic drainage basins, those inland basins not connected directly to ocean, are essential for hydrological modeling of global and regional water balances, land surface water storage, gravity anomalies, sea level rise, etc. Within many hydrological model frameworks, river basins are defined by digital river networks through their flow direction and connectivity datasets. Here we present an improvement to gridded flow direction data and its derivatives produced from upscaled global 5 and 15 arc minute MERIT networks. We explicitly label endorheic and exorheic drainage basins and alter the delineation of endorheic basins by merging small inland watersheds to the adjacent host basins. The resulting datasets have a significantly reduced number of endorheic basins while preserving the total land portion of those basins since most of the merged catchments were inside other larger endorheic areas. We developed and present here the endorheic basin delineation method. This method performs an analysis of the contributing river and basin geometry relative to the location of the flow end point (i.e. potential endorheic lake), proximity of the latter to the drainage basin boundary and the elevation difference between the basin's lowest point and potential spillover location at the basin boundary. The new digital river network was validated using the University of New Hampshire Water Balance Model by comparing the water balance of endorheic inland depressions with modeled accumulation of water in their inland lakes based on the observed historical climate drivers used by WBM.

Earth Systems↗

DOE OSTI2023

MERIT-Plus Dataset: Delineation of endorheic basins in 5 and 15 min upscaled river networks

Endorheic drainage basins, those inland basins not connected directly to ocean, are essential for hydrological modeling of global and regional water balances, land surface water storage, gravity anomalies, sea level rise, etc. Within many hydrological model frameworks, river basins are defined by digital river networks through their flow direction and connectivity datasets. Here we present an improvement to gridded flow direction data and its derivatives produced from upscaled global 5 and 15 arc minute MERIT networks. We explicitly label endorheic and exorheic drainage basins and alter the delineation of endorheic basins by merging small inland watersheds to the adjacent host basins. The resulting datasets have a significantly reduced number of endorheic basins while preserving the total land portion of those basins since most of the merged catchments were inside other larger endorheic areas. We developed and present here the endorheic basin delineation method. This method performs an analysis of the contributing river and basin geometry relative to the location of the flow end point (i.e. potential endorheic lake), proximity of the latter to the drainage basin boundary and the elevation difference between the basin's lowest point and potential spillover location at the basin boundary. The new digital river network was validated using the University of New Hampshire Water Balance Model by comparing the water balance of endorheic inland depressions with modeled accumulation of water in their inland lakes based on the observed historical climate drivers used by WBM.

Earth Systems↗

DOE OSTI2023

MERIT-Plus Dataset: Delineation of endorheic basins in 5 and 15 min upscaled river networks

Endorheic drainage basins, those inland basins not connected directly to ocean, are essential for hydrological modeling of global and regional water balances, land surface water storage, gravity anomalies, sea level rise, etc. Within many hydrological model frameworks, river basins are defined by digital river networks through their flow direction and connectivity datasets. Here we present an improvement to gridded flow direction data and its derivatives produced from upscaled global 5 and 15 arc minute MERIT networks. We explicitly label endorheic and exorheic drainage basins and alter the delineation of endorheic basins by merging small inland watersheds to the adjacent host basins. The resulting datasets have a significantly reduced number of endorheic basins while preserving the total land portion of those basins since most of the merged catchments were inside other larger endorheic areas. We developed and present here the endorheic basin delineation method. This method performs an analysis of the contributing river and basin geometry relative to the location of the flow end point (i.e. potential endorheic lake), proximity of the latter to the drainage basin boundary and the elevation difference between the basin's lowest point and potential spillover location at the basin boundary. The new digital river network was validated using the University of New Hampshire Water Balance Model by comparing the water balance of endorheic inland depressions with modeled accumulation of water in their inland lakes based on the observed historical climate drivers used by WBM.

Earth Systems↗

DOE OSTI2023

MERIT-Plus Dataset: Delineation of endorheic basins in 5 and 15 min upscaled river networks

Endorheic drainage basins, those inland basins not connected directly to ocean, are essential for hydrological modeling of global and regional water balances, land surface water storage, gravity anomalies, sea level rise, etc. Within many hydrological model frameworks, river basins are defined by digital river networks through their flow direction and connectivity datasets. Here we present an improvement to gridded flow direction data and its derivatives produced from upscaled global 5 and 15 arc minute MERIT networks. We explicitly label endorheic and exorheic drainage basins and alter the delineation of endorheic basins by merging small inland watersheds to the adjacent host basins. The resulting datasets have a significantly reduced number of endorheic basins while preserving the total land portion of those basins since most of the merged catchments were inside other larger endorheic areas. We developed and present here the endorheic basin delineation method. This method performs an analysis of the contributing river and basin geometry relative to the location of the flow end point (i.e. potential endorheic lake), proximity of the latter to the drainage basin boundary and the elevation difference between the basin's lowest point and potential spillover location at the basin boundary. The new digital river network was validated using the University of New Hampshire Water Balance Model by comparing the water balance of endorheic inland depressions with modeled accumulation of water in their inland lakes based on the observed historical climate drivers used by WBM.

Earth Systems↗

NASA NTRS1991

Observations of plasma dynamics in the coma of P/Halley by the Giotto Ion Mass Spectrometer

Observations in the coma of P/Halley by the Giotto Ion Mass Spectrometer (IMS) are reported. The High Energy Range Spectrometer (HERS) of the IMS obtained measurements of protons and alpha particles from the far upstream region to the near ionopause region and of ions from mass 12 to 32 at distances of about 250,000 to 40,000 km from the nucleus. Plasma parameters from the High Intensity Spectrometer (HIS) of the IMS obtained between 150,000 to 5000 km from the nucleus are also discussed. The distribution functions of water group ions (water group will be used to refer to ions of 16 to 18 m/q, where m is in AMU and q is in unit charges) are observed to be spherically symmetric in velocity space, indicating strong pitch angle scattering. The discontinuity known as the magnetic pile-up boundary (MPB) is apparent only in proton, alpha, and magnetometer data, indicating that it is a tangential discontinuity of solar wind origin. HERS observations show no significant change in the properties of the heavy ions across the MPB. A comparison of the observations to an MHD model is made. The plasma flow directions at all distances greater than 30,000 km from the nucleus are in agreement with MHD calculations. However, despite the agreement in flow direction, within 200,000 km of the nucleus the magnitude of the velocity is lower than predicted by the MHD model and the density is much larger (a factor of 4). Within 30,000 km of the nucleus there are large theoretical differences between the MHD model flow calculations for the plane containing the magnetic field and for the plane perpendicular to the magnetic field. The observations agreed much better with the pattern calculated for the plane perpendicular to the magnetic field. The data obtained by the High Energy Range Spectrometer (HERS) of the IMS that are published herein were provided to the International Halley Watch archive.

Goldstein, B. E.↗

NASA NTRS2021

Water Recovery from Bioreactor Mixed Liquors Using Forward Osmosis with Polyelectrolyte Draw Solutions

This paper reports on the use of forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. The work was motivated by the need for new regenerative water purification technologies to enable long-duration space missions. Osmotic membrane bioreactors may be an option for water and nutrient recovery in space if they can attain high water flux and reverse solute flux selectivity (RSFS), which quantifies the mass of permeated water per mass of draw solute that has diffused from the draw solution into a bioreactor. Water flux was measured in a direct flow system using wastewater from a municipal wastewater treatment plant and draw solutions prepared with two polyelectrolytes at different concentrations. The direct flow tests displayed a high initial flux (>10 L/m2/h) that decreased rapidly as solids accumulated on the feed side of the membrane. A test with deionized water as the feed revealed a small mass of polyelectrolyte crossover from the draw solution to the feed, yielding an RSFS of 80. Crossflow filtration experiments demonstrated that steady state flux above 2 L/m2·h could be maintained for 70 h following an initial flux decline due to the formation of a foulant cake layer. This study established that FO could be feasible for regenerative water purification from bioreactors. By utilizing a polyelectrolyte draw solute with high RSFS, we expect to overcome the need for draw solute replenishment. This would be a major step towards sustainable operation in long-duration space missions.

Calen R Raulerson↗

DOE OSTI2024

An in situ imaging investigation of the effect of gas flow rates on directed energy deposition

Gas flow rates in Directed Energy Deposition (DED) Additive Manufacturing (AM) can significantly affect the quality of built parts by altering melt pool geometry. Using a DED process replicator and in situ synchrotron radiography, together with analogous experiments in an industrial DED machine, we investigate the impact of carrier gas and shield gas flow rates on build quality. The results reveal that there is a critical shield gas flow rate above which melt pools are flattened, tracks widen, and thus layer thickness decreases. The reduction in layer thickness is most prominent in conditions with low carrier gas flow rate, as the highly turbulent shield gas flow may divert slow moving powder particles away from the melt pool, decreasing capture efficiency. Very high flow rates increase internal porosity, as fast-moving particles impacting the melt pool surface can entrain chamber gas behind them. High gas flow rates also cool the melt pool, creating shallower melt pools with increased thermal gradients near the solidification front, increasing pore entrapment in the solidified track.

Additive manufacturing↗

NASA NTRS1992

Quasiconical flowfield structure of the three-dimensional single fin interaction

A series of conical and three-dimensional computations have been performed for the swept oblique shock wave/turbulent boundary-layer interaction generated by a 20-deg sharp fin at Mach 4 and freestream Reynolds number of 2.18 x 10 exp 5 based on the incoming boundary-layer thickness. The Reynolds-averaged compressible Navier-Stokes equations are employed with turbulence incorporated using the Baldwin-Lomax and Jones-Launder models. The computed results are basically similar for both turbulence models and display general agreement with experimental data for surface pressure and surface flow direction, although underestimating the size of the primary vortex. The computed three-dimensional flowfield displays quasiconical behavior of the surface pressure, surface flow direction, and flowfield contours of static pressure, density, and Mach number over the extent of the computational domain except for an inception region near the fin leading edge. Certain features of the flowfield model are not observed in the computations, namely, a 'normal' shock near the attachment line, transonic shocklets in the expansion region, and secondary separation. The absence of these features in the computation is believed to be indirectly attributable to limitations in the turbulence models.

Knight, Doyle D.↗