Search NASA⌕ Search

SEARCH · Search NASA

Results for “hexafluoride”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Concept for UF6-fueled self-critical DNPL reactor system

An analytical study of a self-critical nuclear pumped laser system concept was performed. The primary emphasis was on a reactor concept which would use gaseous uranium hexafluoride (UF6) as the fissioning material. A reference configuration was selected which has a 3.2 cu m lasing volume as the reactor core. The core is composed of a series of hexagonal graphite tubes which are surrounded by a reflector-moderator composed either of heavy water or beryllium. Laser transitions requiring average fission power densities less than approximately 1 kW/cu cm for excitation are most attractive. Operation at wavelengths greater than approximately 400 nm may be required because of limitations imposed by the opacity of gaseous UF6. Further research directed toward identification of UF6 compatible lasing transitions is required.

Rodgers, R. J.↗
NASA NTRS1979

High temperature UF6 RF plasma experiments applicable to uranium plasma core reactors

An investigation was conducted using a 1.2 MW RF induction heater facility to aid in developing the technology necessary for designing a self critical fissioning uranium plasma core reactor. Pure, high temperature uranium hexafluoride (UF6) was injected into an argon fluid mechanically confined, steady state, RF heated plasma while employing different exhaust systems and diagnostic techniques to simulate and investigate some potential characteristics of uranium plasma core nuclear reactors. The development of techniques and equipment for fluid mechanical confinement of RF heated uranium plasmas with a high density of uranium vapor within the plasma, while simultaneously minimizing deposition of uranium and uranium compounds on the test chamber peripheral wall, endwall surfaces, and primary exhaust ducts, is discussed. The material tests and handling techniques suitable for use with high temperature, high pressure, gaseous UF6 are described and the development of complementary diagnostic instrumentation and measurement techniques to characterize the uranium plasma, effluent exhaust gases, and residue deposited on the test chamber and exhaust system components is reported.

Roman, W. C.↗
NASA NTRS1980

Argon/UF6 plasma experiments: UF6 regeneration and product analysis

An experimental and analytical investigation was conducted to aid in developing some of the technology necessary for designing a self-critical fissioning uranium plasma core reactors (PCR). This technology is applicable to gaseous uranium hexafluoride nuclear-pumped laser systems. The principal equipment used included 1.2 MW RF induction heater, a d.c. plasma torch, a uranium tetrafluoride feeder system, and batch-type fluorine/UF6 regeneration systems. Overall objectives were to continue to develop and test materials and handling techniques suitable for use with high-temperature, high-pressure, gaseous UF6; and to continue development of complementary diagnostic instrumentation and measurement techniques to characterize the effluent exhaust gases and residue deposited on the test chamber and exhaust system components. Specific objectives include: a development of a batch-type UF6 regeneration system employing pure high-temperature fluorine; development of a ruggedized time-of-flight mass spectrometer and associated data acquisition system capable of making on-line concentration measurements of the volatile effluent exhaust gas species in a high RF environment and corrosive environment of UF6 and related halide compounds.

Roman, W. C.↗
NASA NTRS1982

Plasma Etching Improves Solar Cells

Etching front surfaces of screen-printed silicon photovoltaic cells with sulfur hexafluoride plasma found to increase cell performance while maintaining integrity of screen-printed silver contacts. Replacement of evaporated-metal contacts with screen-printed metal contacts proposed as one way to reduce cost of solar cells for terrestrial applications.

Bunyan, S. M.↗
NASA NTRS1982

Density measurement in air with saturable absorbing seed gas

Approaches which have the potential to make density measurements in a compressible flow, where one or more laser beams are used as probes, were investigated. Saturation in sulfur hexafluoride iodine and a crossed beam technique where one beam acts as a saturating beam and the other is at low intensity and acts as a probe beam are considered. It is shown that a balance between an increase in fluorescence intensity with increasing pressure from line broadening and the normal decrease in intensity with increasing pressure from quenching can be used to develop a linear relation between fluorescence intensity and number density and lead to a new density measurement scheme. The method is used to obtain a density image of the cross section of an iodine seeded underexpanded supersonic jet of nitrogen, by illuminating the cross section by a sheet of laser light.

Baganoff, D.↗
NASA NTRS1984

An analysis of the stability of the compressible Ekman boundary layer

The linear stability problem for the compressible Ekman boundary layer common to rotating fluids is formulated and the stability properties determined numerically. Three classes of unstable waves are identified (called class A, B, and C), their properties are described. The class C waves have only recently been reported in the literature and are present only in compressible Ekman boundary layers. Most of the calculations presented here are for uranium hexafluoride gas; however, critical Reynolds numbers are also computed for air and ammonia gas. Compressibility is generally found to decrease the critical Reynolds number for each class of wave. A comparison of results for the three different gases shows the stability to be largely unaffected by changes in the gas properties. Maximum growth rate calculations for each wave show the class A and B waves to be the dominant instabilities.

Spall, J. R.↗
NASA NTRS1985

Wetting layers and dispersion forces for a fluid in contact with a vertical wall

Ellipsometric measurements of the thickness of the wetting layer of sulfur hexafluoride that forms on a fused-silica surface partially immersed in the liquid are presented. The components of the experiment included a He-Ne laser (0.6328 micron), polarizer, and quarter-wave plate with 45-deg azimuth. An optical-grade fused-silica prism was polished to wavelength/20, and strain-induced birefringence was accounted for. It was found that the layer thickness decreases from 40 to 20 nm with a height increase from 0.7 to 3 mm above the liquid-vapor interface. The thickness is independent of the temperature between 10 and 0.1 K below the critical temperature (319 K). The results are compared in detail to the theory of Dzyaloshinskii et al. (1961), and are noted to coincide closely.

Kayser, R. F.↗
NASA NTRS1985

Pulsed excimer laser processing

The status of pulsed excimer laser processing of PV cells is presented. The cost effective feasibility of fabricating high efficiency solar cells on Czochralski wafers using a pulsed excimer laser for junction formation, surface passivation, and front metallization. Laser annealing results were promising with the best AR coated cell having an efficiency of 16.1%. Better results would be expected with larger laser spot size because there was some degradation in open circuit voltage caused by laser spot overlap and edge effects. Surface heating and photolytic decomposition by the laser was used to deposit tungsten from the reaction of tungsten hexafluoride and hydrogen. The line widths were 5 to 10 mils, and the depositions passed the tape adhesion test. Thinner lines are practical using an optimized optical system.

Wong, D.↗
NASA NTRS1987

Plasma instability in the presence of negative ions

Ion density fluctuations are studied in a diffusion-controlled argon plasma containing, as a dilutant, two electron-attaching species, carbon dioxide and sulfur hexafluoride. It is found that the system becomes increasingly unstable as the concentration of the electron-attaching species is increased. Nonlinear mode-mode couplings have been identified and the coupling coefficients for these interactions have been computed. Turbulent fluctuations are observed to have pronounced three-dimensionality with distinct axial and azimuthal behaviors. The power spectra of these fluctuations are composed of many discrete modes. The importance of changes in the total discharge pressure is dependent on the electron-attachment cross section of the dilutant species. From these results it is shown that the ionization instability is probably responsible for the observed phenomenon.

Johnson, J. A., III↗
NASA NTRS1987

The effect of wind and currents on gas exchange in an estuarine system

The objectives were to develop a non-volatile tracer to use in gas exchange experiments in laterally unconfined systems and to study applications of deliberate tracers in limnology and oceanography. Progress was made on both fronts but work on the development of the non-volatile tracer proved to be more difficult and labor intensive that anticipated so no field experiments using non-volatile tracers was performed as yet. In the search for a suitable non-volatile tracer for an ocean scale gas exchange experiment a tracer was discovered which does not have the required sensitivity for a large scale experiment, but is very easy to analyze and will be well suited for smaller experiments such as gas exchange determinations on rivers and streams. Sulfur hexafluoride, SF6, was used successfully as a volatile tracer along with tritium as a non-volatile tracer to study gas exchange rates from a primary stream. This is the first gas exchange experiment in which gas exchange rates were determined on a head water stream where significant groundwater input occurs along the reach. In conjunction with SF6, Radon-222 measurements were performed on the groundwater and in the stream. The feasibility of using a combination of SF6 and radon is being studied to determine groundwater inputs and gas exchange of rates in streams with significant groundwater input without using a non-volatile tracer.

Broecker, W. S.↗
NASA NTRS1991

The Santa Monica Basin Tracer Experiment - A study of diapycnal and isopycnal mixing

Cross isopycnal (diapycnal) and lateral mixing and stirring below the sill of Santa Monica Basin were studied by releasing two tracers, sulfur hexafluoride and perfluorodecalin, as close as possible to an isopycnal surface and measuring their subsequent dispersion. The target for the release was a potential temperature surface at about 790 m depth, roughly 100 m above the bottom and 50 m below the sill. Three surveys, performed immediately after, about 7 weeks after, and about 6 months after the release, showed that the time scales for lateral stirring and mixing in the basin were between 2 and 5 months. The diapycnal diffusivity for the whole period was found to be 0.29 + or - 0.06 sq cm/s near the injection surface, where the buoyancy frequency was about 1.1 cph. This estimate may include some mixing in the turbulent boundary layer near the walls of the basin. The best estimate for the diapycnal diffusivity in the basin interior is 0.25 + or - 0.08 sq cm/s.

Ledwell, James R.↗
NASA NTRS1991

In-flight off-surface flow visualization using infrared imaging

A light test investigation was conducted to evaluate an infrared (IR) imaging technique to visualize off-surface flow phenomena. A single-engine, general-aviation airplane was equipped with an IR imaging system that viewed the region around the left wingtip. Vortical flow at the wingtip was seeded with surfur hexafluoride, a gas with strong infrared absorbing and emitting characteristics. Different terrain and sky backgrounds were evaluated for their effect on IR images of vortical flow. The best IR images were obtained with a clear background. The results of the investigation indicate that IR flow visualization compliments existing smoke generator methods for off-surface flow visualization.

Manuel, Gregory S.↗
NASA NTRS1991

Vapor core propulsion reactors

Many research issues were addressed. For example, it became obvious that uranium tetrafluoride (UF4) is a most preferred fuel over uranium hexafluoride (UF6). UF4 has a very attractive vaporization point (1 atm at 1800 K). Materials compatible with UF4 were looked at, like tungsten, molybdenum, rhenium, carbon. It was found that in the molten state, UF4 and uranium attacked most everything, but in the vapor state they are not that bad. Compatible materials were identified for both the liquid and vapor states. A series of analyses were established to determine how the cavity should be designed. A series of experiments were performed to determine the properties of the fluid, including enhancement of the electrical conductivity of the system. CFD's and experimental programs are available that deal with most of the major issues.

Diaz, Nils J.↗
NASA NTRS1992

Modifications to Langley 0.3-m TCT adaptive wall software for heavy gas test medium, phase 1 studies

The scheme for two-dimensional wall adaptation with sulfur hexafluoride (SF6) as test gas in the NASA Langley Research Center 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT) is presented. A unified version of the wall adaptation software has been developed to function in a dual gas operation mode (nitrogen or SF6). The feature of ideal gas calculations for nitrogen operation is retained. For SF6 operation, real gas properties have been computed using the departure function technique. Installation of the software on the 0.3-m TCT ModComp-A computer and preliminary validation with nitrogen operation were found to be satisfactory. Further validation and improvements to the software will be undertaken when the 0.3-m TCT is ready for operation with SF6 gas.

Murthy, A. V.↗
NASA NTRS1993

A feasibility study of using Langley 0.3-m transonic cryogenic tunnel sidewall boundary-layer removal system for heavy gas testing

This report presents the results of a preliminary study for using the 0.3-m Transonic Cryogenic Tunnel sidewall boundary-layer removal system with heavy gas sulfur hexafluoride as the test medium. It is shown that the drive motor speed/power of the existing system and the additional heat load on the tunnel heat exchanger are the major problems limiting the boundary-layer removal system performance. Overcoming these problems can provide the capability to remove about 1.5 percent of the test section mass flow at Mach number M = 0.8 and about 5 percent at M = 0.25. Previous studies have shown that these boundary-layer mass flow removal rates can reduce the boundary-layer thickness by a factor of two at the model station. Also the effect of upstream boundary-layer removal on the airfoil test data is not likely to be significant under high lifting conditions. Near design conditions, corrections to the test Mach number may be necessary to account for sidewall boundary-layer effects.

Murthy, A. V.↗
NASA NTRS1995

High energy collimating fine grids

The objective of this project was to demonstrate the fabrication of extremely tight tolerance collimating grids using a high-Z material, specifically tungsten. The approach taken was to fabricate grids by a replication method involving the coating of a silicon grid substrate with tungsten by chemical vapor deposition (CVD). A negative of the desired grid structure was fabricated in silicon using highly wafering techniques developed for the semiconductor industry and capable of producing the required tolerances. Using diamond wafering blades, a network of accurately spaced slots was machined into a single-crystal silicon surface. These slots were then filled with tungsten by CVD, via the hydrogen reduction of tungsten hexafluoride. Following tungsten deposition, the silicon negative was etched away to leave the tungsten collimating grid structure. The project was divided into five tasks: (1) identify materials of construction for the replica and final collimating grid structures; (2) identify and implement a micromachining technique for manufacturing the negative collimator replicas (performed by NASA/JPL); (3) develop a CVD technique and processing parameters suitable for the complete tungsten densification of the collimator replicas; (4) develop a chemical etching technique for the removal of the collimator replicas after the tungsten deposition process; and (5) fabricate and deliver tungsten collimating grid specimens.

Arrieta, Victor M.↗
NASA NTRS1996

Insights into Ventilatory Inhomogeneity from Respiratory Measurements on Spacelab Mission D-2

The relative contributions of inter-regional and intra-regional ventilation inhomogeneities of Spacelab astronauts are studied. The classical theory of ventilation distribution in the lung is that the top-to-bottom (inter-regional) ventilation inhomogeneities are primarily gravity dependent, whereas the peripheral (intra-regional) ventilation distribution is gravity independent. Argon rebreathing tests showed that gravity independent specific ventilation (ventilation per unit volume) inhomogeneities are at least as large as gravity dependent ones. Single breath tests with helium and sulfur hexafluoride showed the different sensitivity of these gases to microgravity.

Paiva, Manuel↗
NASA NTRS1959

Halogen-Containing Gases as Boundary Lubricants for Corrosion-Resistant Alloys at 1200 F

The extreme temperatures anticipated for lubricated parts in advanced flight powerplants dictate the consideration of unconventional methods of lubrication such as solid lubricants and the reactive gases described in the present research. These halogen-containing "reactive" gases such as dichlorodifluoromethane, CF2Cl2, are among the most stable of organic molecules. The high "flash" temperatures generated at the contacting asperities as a result of frictional heat are sufficient to cause local decomposition of the halogen-containing gases. The active atoms thus released (e.g., chlorine) then react with the metal to be lubricated to form halides capable of effective lubrication. The presence of small amounts of a sulfur-containing gas (e.g., 1 percent sulfur hexafluoride, SF6) was found to catalyze the formation of metal halides. Friction and wear studies were made with a hemisphere (3/16-in. rad.) rider sliding in a circumferential path on the flat surface of a rotating disk (2 1/2-in. diam.). The specimens of corrosion-resistant 2 alloys were run in an atmosphere of the various gases with a load of 1200 grams, a sliding velocity of 120 feet per minute, and temperature from 75 to 1200 F. An effective lubricant for ferritic materials (M-1 tool steel) was CF2Cl2, but significant corrosion occurred above 600 F. Corrosion evaluation in CF2Cl2 suggested a number of nickel- and cobalt-base alloys for additional lubrication study. Several combinations of gases and these metals were found to lubricate to 1200 F without excessive corrosion. The gases were CF2Cl2 Plus 1 percent SF6, monobromotrifluoromethane CF3Br plus 1 percent SF6, dibromodifluoromethane CF2Br2, iodotrifluoromethane, CF3I, and I2. Careful selection of metals and gas are necessary for successful lubrication over specific temperature ranges. Optimum combinations give friction coefficients as low as 0.05 without

Buckley, Donald H.↗