Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical and Corrosion Response of 316SS in Supercritical CO 2

The supercritical carbon dioxide (s-CO 2 ) Brayton cycle is currently being explored as a replacement for the steam Rankine cycle due to its potential for higher efficiency and lower cycle cost. 316 stainless steel is a candidate alloy for use in s-CO 2 up to roughly 600 °C, but the mechanical effects of prolonged exposure of base and welded material in s-CO 2 have not been analyzed. The potential for carburization makes this an important concern for the implementation of 316 and similar austenitic stainless steels in the s-CO 2 environment. In this study, welded and base material of two types of 316–316L and 316H–were exposed in either s-CO 2 or argon at 550 °C or 750 °C for 1000 h. 550 °C s-CO 2 exposure yielded a thin (< 1 µm) Cr oxide with occasional nodules of duplex Fe oxide and Fe–Cr spinel that were up to 5 microns thick. However, tensile results from s-CO –2 exposure matched those of 550 °C thermal aging in Ar, indicating that no mechanically detrimental carburization occurred in either 316 variant after 1000 h exposure. Conversely, 750 °C s-CO 2 exposure produced roughly 10 × the oxide thickness, with a more substantial Fe oxide (3–5 µm) on the majority of the surface and nodules of up to 40 µm thick. In comparison to aged samples, tensile testing of 750 °C CO 2 -exposed samples revealed ductility loss attributed to carburization. As a result, projections of 316L performance in s-CO 2 indicate that mechanically detrimental carburization—equal to that shown here for 750 °C, 1000 h—will likely be present after 7–14 years of service at 550 °C.

316 stainless steel↗
DOE OSTI2020

Electrochemical Li Intercalation in Black Phosphorus: In Situ and Ex Situ Studies

A systematic study on electrochemical charge transfer in Li-doped black phosphorous (BP) was carried out by both in-situ and ex-situ Raman scattering. Galvanostatic discharge of dedicated in-situ electrochemical cell for Raman spectroscopy was used to study time evolution of vibrational modes under lithiation. In addition to the peak broadening which is a result of structural expansion, peaks corresponding to all three atomic vibrational modes A 1 g , B 2 g and A 2 g were found to red-shift as a result of lithiation. Peaks B 2 g and A 2 g were shifted about 1.6 times more towards lower wavenumbers in comparison to A 1 g . Further characterizations using optical and electron microscopy showed that the intercalation of BP is highly anisotropic, where channels along the zigzag direction were found to be the easy direction for intercalation. X-ray diffraction on intercalated samples confirmed a reduction of thickness as lithiation weakens interlayer bonding, thus resulting in a partial exfoliation of BP flakes. Here, first principle studies using density function theory (DFT) were used to develop a theoretical model for the intercalation mechanism. The discrepancy between the experimental and the theoretical results was also addressed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

High resolution >40 keV x-ray radiography using an edge-on micro-flag backlighter at NIF-ARC

Radiography of low-contrast features in high-density materials evolving on a nanosecond timescale requires a bright photon source in the tens of keV range with high temporal and spatial resolution. One application for sources in this category is the study of dynamic material strength in samples compressed to Mbar pressures at the National Ignition Facility, high-resolution measurements of plastic deformation under conditions relevant to meteor impacts, geophysics, armor development, and inertial confinement fusion. Here, we present radiographic data and the modulation transfer function (MTF) analysis of a multi-component test object probed at ~100 keV effective backlighter energy using a 5 μm-thin dysprosium foil driven by the NIF Advanced Radiographic Capability (ARC) short-pulse laser (~2 kJ, 10 ps). The thin edge of the foil acts as a bright line-projection source of hard x rays, which images the test object at 13.2× magnification into a filtered and shielded image plate detector stack. The system demonstrates a superior contrast of shallow (5 μm amplitude) sinusoidal ripples on gold samples up to 90 μm thick as well as enhanced spatial and temporal resolution using only a small fraction of the laser energy compared to an existing long-pulse-driven backlighter used routinely at the NIF for dynamic strength experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Mapping the 3D position of battery cathode particles in Bragg coherent diffractive imaging

In Bragg coherent diffractive imaging, the precise location of the measured crystals in the interior of the sample is usually missing. Obtaining this information would help the study of the spatially dependent behavior of particles in the bulk of inhomogeneous samples, such as extra-thick battery cathodes. This work presents an approach to determine the 3D position of particles by precisely aligning them at the instrument axis of rotation. In the test experiment reported here, with a 60 µm-thick LiNi 0.5 Mn 1.5 O 4 battery cathode, the particles were located with a precision of 20 µm in the out-of-plane direction, and the in-plane coordinates were determined with a precision of 1 µm.

25 ENERGY STORAGE↗
DOE OSTI2023

GaAs-based superlattice photocathodes manufactured using MOCVD provide spin polarization > 90% and quantum efficiency > 1%

Spin-polarized electron beams are important for nuclear physics research performed at electron accelerators. Over many years, beam polarization has increased significantly, from 35% provided by unstrained bulk GaAs, to ~ 75% using single strained-layer GaAs, to ~ 90% using strained-superlattice GaAs photocathodes grown using molecular beam epitaxy (MBE). Commercial vendors once provided high-polarization photocathodes but today there is little interest in supporting this small market. Here, we report successful results fabricating high polarization GaAs/GaAsP superlattice photocathodes using metal organic chemical vapor deposition (MOCVD), a method dismissed by some as not providing sufficient control of layer thickness and uniformity. The best samples provide spin polarization greater than 90% and quantum efficiency (QE) exceeding 2%, with QE enhanced using a distributed Bragg reflector (DBR) incorporated into the structure. Together, these quantities represent some of the best results ever reported for high polarization photocathodes. Enhanced QE via DRB is very important for future work at CEBAF/Jefferson Lab because it will simplify the production of polarized electron beams at milliampere current needed for a polarized positron source.

Poelker, Matt↗
DOE OSTI2025

An integrated approach to examine fuel-cladding chemical interaction in HT9/U-10Zr metallic fast reactor fuels: Coupling machine learning with electron microscopy and local mechanical properties analysis

The metallic U-Zr nuclear fuel alloy has garnered renewed interest as a promising candidate for next-generation sodium-cooled fast reactors. Recent studies and technology assessments have identified several areas requiring improvements, enhanced knowledge, and reliable data to strengthen the U-Zr fuel design basis for qualification and commercial applications. One of the most challenging phenomena impacting this fuel system’s performance is fuel-cladding chemical interaction (FCCI). This work aimed to harvest FCCI data by examining selected HT9/U-10Zr (wt. %) fuel samples of prototypic full-length fuel pins through an integrated approach. This approach integrated scanning electron microscopy (SEM) microstructure characterization with localized mechanical properties examination to deepen understanding of FCCI phenomenon in HT9/U-10Zr fuel system. Particularly, this study focused on MFF fuel pins irradiated at Fast Flux Test Facility (FFTF), which aimed to qualify metallic fuel as a driver fuel for FFTF and to assess its viability for larger-scale fast reactors. Electron microscopy provided high confidence in detecting and distinguishing the different FCCI layers, while small-scale mechanical testing (SSMT) probed the mechanical properties of these layers. SEM examination of a MFF-2 pin 192167, with a time averaged inner cladding temperature (TICT) slightly over 500°C, revealed minimal cladding-side FCCI (cladding wastage). In contrast, significantly thicker cladding wastage comprising two distinct sublayers was observed in samples from the thermally hot MFF-3 pin 193045 and MFF-5 pin 195011 where the TICT ranged from 610-635°C. SSMT indicated complete embrittlement in the sublayer adjacent to the fuel and a tendency toward embrittlement in the other sublayer. Additionally, a new machine learning method was developed, validated, and used to quantify cladding wastage thickness. The machine learning method reliably predicted the wastage thickness across various fuel pins and sample cross-sections. Furthermore, the available cladding wastage data from HT9/U-10Zr fuel system demonstrated a strong temperature dependency. However, the dataset remains small, and ongoing research activities are essential to further understand the FCCI phenomenon and develop a reliable FCCI model for enhanced fuel performance simulation under various conditions.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2022

Hot Forging Options for Thick Castings

Uranium alloyed with 10 wt% molybdenum (U-10Mo) is a monolithic nuclear fuel relevant to the National Nuclear Security Administration’s nonproliferation efforts. Research has been underway to optimize processing techniques for the U-10Mo fuel. This study investigated the use of hot compression or “hot forging” on a thick (~1") cast and homogenized U-10Mo plate before standard hot and cold rolling procedures. After plates were cast and homogenized, six samples were cut and forged at 700°C at a strain rate of either 0.10 s –1 or 0.01 s –1 at six levels of reduction. After forging, all samples underwent hot and cold rolling followed by annealing to achieve a final foil thickness of about 0.0085". Samples were taken at each stage of the casting and thermomechanical processing to assess the microstructural evolution. Chemical composition, microstructure, and uranium carbide morphology are presented and assessed in this study. Upon hot forging, dislocations accumulate along the grain boundaries, which serve as nucleation sites for randomly oriented, strain-free grains during subsequent annealing steps. Hot forging and subsequent annealing produced very heterogeneous grain sizes. However, no molybdenum segregation was observed after forging. No obvious trend was observed between forging conditions (strain rate and reduction percentage) and the microstructure after final thermomechanical processing. Upon hot rolling to 0.04" and annealing (700°C for 45 min), the average grain diameters from OM was 17 ± 2 µm across the six different forged samples. The subsequent cold rolling to 0.0085" and then annealing (700°C for 45 min) resulted in an average of 13 ± 2 µm between the six samples. Thus, the starting, as-forged microstructure did not appear to significantly influence the final microstructure of the cold-rolled foil. These results will help with understanding and expanding hot working capabilities for thicker U-10Mo castings. They also provide useful information on the effects of hot forging and its potential use to minimize defects that can arise during subsequent hot and cold rolling procedures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Marine and continental stratocumulus cloud microphysical properties obtained from routine ARM Cimel sunphotometer observations

This study investigates marine and continental stratocumulus (Sc) cloud properties obtained from an automated implementation of a multispectral photometer retrieval. Photometer methods simultaneously retrieve cloud optical depth (τ) and cloud droplet effective radius (r e ), with estimates for liquid water path (LWP) calculated on the availability of those quantities. These applied methods evaluate retrieved cloud properties for Sc identified during a recent 6 year period over the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) program sites in Oklahoma, USA (SGP) and in the Azores, Portugal (ENA). Modest agreement in key quantity retrievals is found between the routine photometer products and multisensor collocated profiling references. Cumulative breakdowns contingent on cloud thickness indicate increases in all retrieved quantities in thicker clouds, with larger discrepancies in the relative performance between the retrievals collected in the presence of drizzle. Under continental cloud conditions, the clouds of a similar thickness and r e to those sampled under marine conditions report a factor of 1.5 larger τ and LWP. An r 2 ≅0.65 is found between photometer τ retrievals and shadowband radiometer measurements, with photometer retrievals reporting a high (relative) bias. The τ intercomparisons indicate that variability between retrievals is a factor of three larger than errors reported from individual retrieval input perturbation tests. Photometer r e retrievals suggest a low r 2 (< 0.1) having a standard deviation ≅ 3 µm when compared to ARM baseline multi-sensor radar/radiometer references (accounting for offsets in the cloud droplet number concentration assumptions of the latter). However, photometer LWP calculations remain relatively unbiased in non-drizzling conditions, with errors O (50 g m −2 ) and r 2 ≅0.5 to collocated radiometer and interferometer references. Additional sensitivity tests for island influences on marine Sc properties suggest that while island-influenced winds may promote larger cloud LWP or thickness, the influence could be within retrieval method uncertainty and/or collocated instrument variability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Neutron diffraction illustrates residual stress behavior of welded alloys used as radioactive confinement boundary

Corrosion-resistant welded alloys are frequently used as a leak-tight boundary in critical applications that require confinement of hazardous and/or radioactive substances, including an increasing population of spent nuclear fuel (SNF) canisters. The behavior of residual stresses generated as a result of irregular elastic–plastic deformation during processes such as welding is one of today's key issues to a full understanding of the aging mechanisms that may compromise the confinement boundary. Whether such processes and any subsequent weld repairs, not subjected to post-weld heat treatment, would negatively affect the initial material by introducing through-thickness tensile stresses remains an open question. Here we report the first residual stress measurements using neutron diffraction on the welded joints of a SNF canister. We found significant tensile residual stresses in the as welded sample, indicating that initiation and through-thickness growth of cracks may be possible. Following repair, we observed a stress redistribution and introduction of beneficial compressive stresses. We anticipate our results will improve understanding of confinement susceptibility to aging and guide improvements in repair techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Measurements of effective actinides neutron capture cross sections in a cadmium-filtered epithermal neutron spectrum

In this work, a total of 20 actinide samples were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL): 233 U (1), 235 U (1), 236 U (1), 238 U (1), 237 Np (2), 239 Pu (1), 240 Pu (1), 242 Pu (2), 244 Pu (2), 241 Am (2), 243 Am (2), 244 Cm (2), and 248 Cm (2). The samples were loaded in a basket containing a 1.1-mm thick cadmium filter. The presence of the filter drastically changes the neutron spectrum in the samples and accentuates the reaction rates in the resonance region. Isotopic ratios were determined using Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS) that allowed inferring effective capture cross sections. Detailed best-estimate MCNP models of the experiment using ENDF/B-VII.0 nuclear data were developed to calculate the effective neutron cross sections and, subsequently, compare them with the cross sections inferred from experimental results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

A method for mapping submicron-scale crystallographic order/disorder applied to human tooth enamel

Tooth enamel, the outermost layer of human teeth, is a complex, hierarchically structured biocomposite. The details of this structure are important in multiple human health contexts, from understanding the progression of dental caries (tooth decay) to understanding the process of amelogenesis and related developmental defects. Enamel is composed primarily of long, nanoscale crystallites of hydroxyapatite that are bundled by the thousands to form micron-scale rods. Studies with transmission electron microscopy show the relationships between small groups of crystallites and X-ray diffraction characterize averages over many rods, but the direct measurement of variations in local crystallographic structure across and between enamel rods has been missing. Here, we describe a synchrotron X-ray-based experimental approach and a novel analysis method developed to address this gap in knowledge. A ~500-nm-wide beam of monochromatic X-rays in conjunction with a sample section only 1 μm in thickness enables 2D diffraction patterns to be collected from small well-separated volumes within the enamel microstructure but still probes enough crystallites (~300 per pattern) to extract population-level statistics on crystallographic features like lattice parameter, crystallite size, and orientation distributions. Furthermore, the development of a quantitative metric to characterize relative order and disorder based on the azimuthal autocorrelation of diffracted intensity enables these crystallographic measurements to be correlated with their location within the enamel microstructure (e.g., between rod and interrod regions). These methods represent a step forward in the characterization of human enamel and will elucidate the variation of the crystallographic structure across and between enamel rods for the first time.

crystallographic order/disorder↗
DOE OSTI2024

Scalable Surface Micro-Texturing of LLZO Solid Electrolytes for Battery Applications

A challenge for lithium lanthanum zirconate (LLZO)-based solid-state batteries is to increase the critical current density (CCD) to enable high current cycling. A promising strategy is to modify the LLZO surface morphology to provide a larger contact area with the Li metal. Here, a surface-textured thin LLZO electrolyte was prepared through an easily scalable process. The texturing process is a simple pressing of green LLZO tapes between micro-textured substrates. A variety of textures can be produced, depending on the type of substrate, and texturing can be on either one side or both sides. For this work, after pressing and sintering, several micro-patterns are formed on thin LLZO (~118 μm thick). The properties of the various samples were characterized to investigate the impact of surface texturing, and the most promising ones were selected for electrochemical testing in symmetrical lithium cells and full cells. Li symmetric cells using a coarse ridge-textured LLZO exhibit ~2.5 times increased CCD compared to planar non-textured LLZO, and a solid-state full cell shows stable cycling and improved rate performance. Finally, we believe this process offers a favorable trade-off of processing complexity vs structural optimization to maximize CCD.

25 ENERGY STORAGE↗
DOE OSTI2025

Direct observation of distinct bulk and edge nonequilibrium spin accumulation in ultrathin MoTe 2

Low-symmetry two-dimensional (2D) topological materials such as MoTe 2 host efficient charge-to-spin conversion (CSC) mechanisms that can be harnessed for novel electronic and spintronic devices. However, the nature of the various CSC mechanisms and their correlation with underlying crystal symmetries remain unsettled. In this work, we use local spin-sensitive electrochemical potential measurements to directly probe the spatially dependent nonequilibrium spin accumulation in MoTe 2 flakes down to four atomic layers. We are able to clearly disentangle contributions originating from the spin Hall and Rashba-Edelstein effects and uncover an abundance of unconventional spin polarizations that develop uniquely in the sample bulk and edges with decreasing thickness. Using ab-initio calculations, we construct a unified understanding of all the observed CSC components in relation to the material dimensionality and stacking arrangement. Our findings not only illuminate previous CSC results on MoTe 2 but also have important ramifications for future devices that can exploit the local and layer-dependent spin properties of this 2D topological material.

Science & Technology - Other Topics↗
DOE OSTI2024

Antiferromagnetic order in the layered magnetic topological insulator MnBi 2 ⁢Se 4 probed by resonant soft x-ray scattering

The quasi-two-dimensional magnetic topological insulator MnBi 2 Se 4 , stabilized via nonequilibrium molecular beam epitaxy, is investigated by resonant soft x-ray scattering. Kiessig fringes are observed, confirming a high sample quality and a thin film thickness of 10 septuple layers (∼13 nm). An antiferromagnetic Bragg peak is observed at the structurally forbidden reflection, whose magnetic nature is validated by studying its temperature, energy, and polarization dependence. Through a detailed analysis, an A-type antiferromagetic order with in-plane moments is implied. This alternative spin structure in MnBi 2 Se 4 , in contrast to the Ising antiferromagnetic states in other magnetic topological insulators, might be relevant for hosting new topological states.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Impacts of the Additive Manufacturing Process on the Roughness of Engine Scale Vanes and Cooling Channels

Abstract By leveraging the additive manufacturing (AM) platform, development time and costs for turbine component testing can be reduced relative to traditional investment casting. Surface roughness is a key characteristic of the additive manufacturing process that can impact flow, heat transfer, and mechanical integrity of printed components. There are multiple design and build considerations that result in variability in surface roughness, especially when additively fabricating complicated three-dimensional vanes and internal cooling passages. This study characterizes the surface roughness of internal cooling passages, vanes, and flat external surface samples made using additive manufacturing, specifically the direct metal laser sintering process. The samples were manufactured with various wall thicknesses, layer thicknesses, build locations, build directions, and on different AM machines. A combination of computed tomography scanning and optical profilometry was used to evaluate surface roughness levels. The data indicate that the dominant factors in roughness for a given layer thickness are a function of wall thickness, build location, and build direction.

Engineering↗
DOE OSTI2025

Microstructural evaluation of thin-wall sections of 316L stainless steel produced by laser powder-bed fusion processing

The synthesis of thin wall sections that are only 0.4 mm thick is achieved with LPBF AM. Sample preparation is optimized using metallographic polishing to produce samples with only 0.3 um rms roughness for scanning electron microanalysis with EBSD and EDS. A fully austenitic 316L phase is found without evidence of secondary phases. Unlike some AM products that can readily evidence composition segregation due to solute rejection as attributable to temperature gradients within the solidification

Jankowski, Alan F. [Sandia National Laboratories (↗
DOE OSTI2023

Hardware, methodology and applications of 2 + D backscatter Mössbauer spectroscopy with simultaneous x-ray and γ-ray detection

Abstract A unique method is presented for the acquisition and analysis of 57 Fe backscatter Mössbauer spectra with simultaneous detection of the resonant 14.4 keV γ -rays and the characteristic 6.4 keV x-rays, using a custom-built multi-parameter analyser constructed on the basis of commercial analogue to digital converters and high-speed digital latches. The system allows for the simultaneous registration of Doppler-modulation velocities and photon energies, with up to 4096 and 8192 digital channels respectively. This arrangement is in contrast to most related systems, which detect at a single narrow energy window per detector. Samples of arbitrary atomic structure, morphology and surface topography can be studied without altering the setup or the analysis procedure, provided that the samples are at least micrometre sized. The hardware and software that are used to acquire data with minimal dead time are described and the custom and self-contained methods for post-measurement energy discrimination, background correction and velocity-axis folding are discussed. The data are fit using a general Hamiltonian model for the nuclear energy levels of 57 Fe and a quantum mechanical description of the angular momentum coupling is utilised, with consideration of the crystalline and chemical disorder of the sample under examination. Three examples of distinct magnetic systems, with thicknesses ranging from 5 μ m to 6 mm, that were studied using this method are presented, these are: an amorphous CoFeB-based ribbon with ultra-soft coercivity for high-frequency applications, magnetically hard Nd-Fe-B thick films on Si substrates, examined in both as-deposited and annealed states, and a sample from the nickel-rich iron meteorite NWA 6259 that contains the atomically ordered, elevated coercivity, L 1 0 phase of FeNi, tetrataenite. The wide applicability and usefulness of this method is thus demonstrated on three distinct sample morphologies that required little to no surface preparation prior to examination.

Engineering↗