SEARCH · Search NASA

Results for “simulation types and techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Dynamic verification of a digital flight control system.

Development of a digital control system dynamic variation technique which accounts for the limitation of available frequency response analyzers. Digital control system theory is briefly reviewed, and generation of the necessary theoretical frequency responses is discussed. Results of the dynamic verification of a digital control system for a Saturn V launch vehicle are presented, and attention is given to the limitations of this technique along with its applicability to other types of digital control systems. A technique for performing open-loop frequency response analyses of a flight program implemented in a 'flight-type' digital computer and interface hardware with vehicle dynamics simulated on an analog computer is described.

Nabers, J. P., Jr.↗

NASA NTRS1990

Windshear detection - Airborne system perspective

Functional requirements for airborne windshear detection and warning are discussed based on performance criteria of remote sensor devices such as Doppler radar, Doppler laser radar, and infrared radiometric techniques. These types of sensors are considered able to detect hazardous windshear conditions and provide adequate warning time for the flight crew to escape the encounter. Radar simulation and analysis show that windshear from microbursts can be detected. The Doppler systems can provide line-of-sight information from a region extending 2-4 km in front of the aircraft. The temperature drop associated with the formation of windshear can be measured by an airborne infrared radiometer which compares emission from CO2 in the immediate neighborhood of the aircraft to the emissions from CO2 in the air 4-5 km away. It is suggested that an integration of airborne sensor and ground derived data can support microburst avoidance.

Bowles, Roland L.↗

DOE OSTI2020

Thermal Frequency Drift of 3D Printed Microwave Components

Fabrication of microwave slot array antennas and waveguide bandpass and notch filters using 3D printing has significant advantages in terms of speed and cost even for parts with high mechanical complexity. One disadvantage of Stereolithography (SLA) 3D printed, copper plated microwave components is that some SLA resins have a high Coefficient of Thermal Expansion (CTE), quoted in micrometers per meter per degree or 10 -6 per degree. Compared to typically used metals such as aluminum (CTE 24 × 10 -6 ·K -1 ) and copper (CTE 17 × 10 -6 ·K -1 ), SLA resin can have CTE above 100 × 10 -6 ·K -1 . Resonant structures experience significant frequency drift with temperature changes on the order of 10–50 °C. The issue of 3D printed microwave structures changing frequency characteristics significantly with temperature shift has not been addressed or reviewed in current literature. We measured and simulated the effect of temperature change on a slot array, cavity notch filters, and post loaded waveguide bandpass filters. We tested several types of SLA resin, different plating techniques, and also Direct Metal Laser Sintering (DMLS) and Binder Infusion metal 3D printing. Performance as a function of temperature is presented for these alternatives.

three-dimensional printing↗

NASA NTRS1977

Small monopropellant thruster contamination measurement in a high-vacuum low-temperature facility

The contamination that results from the exhaust plume of small thrusters used for attitude control maneuvers can pose severe problems for long-life satellite systems. In order to assess this type of contamination problem, analytical and experimental techniques must be developed. Mass deposition rate measurements of a representative 0.44-N thrust hydrazine thruster were made in a space simulation chamber using five appropriately placed variable-temperature quartz crystal microbalances. The mass deposition rates within the thruster plume were measured while operating the thruster over a wide range of operating parameters, including duty cycles, catalyst bed start temperatures, propellant water variation, as well as thruster aging effects. The contamination measurements were made over a temperature range of 144 to 256 K for all duty cycles. In addition, the nominal duty cycle of 100 msec on and 10 sec off was run at a temperature of 106 K. These data will make possible better prediction of deposition rates of contaminants from thrusters used in satellite systems.

Passamaneck, R. S.↗

NASA NTRS2015

Linear Covariance Analysis For Proximity Operations Around Asteroid 2008 EV5

The NASA initiative to collect an asteroid, the Asteroid Robotic Redirect Mission (ARRM), is currently investigating the option of retrieving a boulder from an asteroid, demonstrating planetary defense with an enhanced gravity tractor technique, and returning it to a lunar orbit. Techniques for accomplishing this are being investigated by the Satellite Servicing Capabilities Office (SSCO) at NASA GSFC in collaboration with JPL, NASA JSC, LaRC, and Draper Laboratory, Inc. Two critical phases of the mission are the descent to the boulder and the Enhanced Gravity Tractor demonstration. A linear covariance analysis is done for these phases to assess the feasibility of these concepts with the proposed design of the sensor and actuator suite of the Asteroid Redirect Vehicle (ARV). The sensor suite for this analysis includes a wide field of view camera, LiDAR, and an IMU. The proposed asteroid of interest is currently the C-type asteroid 2008 EV5, a carbonaceous chondrite that is of high interest to the scientific community. This paper presents an overview of the linear covariance analysis techniques and simulation tool, provides sensor and actuator models, and addresses the feasibility of descending to the surface of the asteroid within allocated requirements as well as the possibility of maintaining a halo orbit to demonstrate the Enhanced Gravity Tractor technique.

Navigation↗

NASA NTRS1992

Overview of the relevant CFD work at Thiokol Corporation

An in-house developed proprietary advanced computational fluid dynamics code called SHARP (Trademark) is a primary tool for many flow simulations and design analyses. The SHARP code is a time dependent, two dimensional (2-D) axisymmetric numerical solution technique for the compressible Navier-Stokes equations. The solution technique in SHARP uses a vectorizable implicit, second order accurate in time and space, finite volume scheme based on an upwind flux-difference splitting of a Roe-type approximated Riemann solver, Van Leer's flux vector splitting, and a fourth order artificial dissipation scheme with a preconditioning to accelerate the flow solution. Turbulence is simulated by an algebraic model, and ultimately the kappa-epsilon model. Some other capabilities of the code are 2-D two-phase Lagrangian particle tracking and cell blockages. Extensive development and testing has been conducted on the 3-D version of the code with flow, combustion, and turbulence interactions. The emphasis here is on the specific applications of SHARP in Solid Rocket Motor design. Information is given in viewgraph form.

Chwalowski, Pawel↗

DOE OSTI2023

Physics guided machine learning for multi-material decomposition of tissues from dual-energy CT scans of simulated breast models with calcifications

We introduce a physics guided data-driven method for image-based multi-material decomposition for dual-energy computed tomography (CT) scans. The method is demonstrated for CT scans of virtual human phantoms containing more than two types of tissues. The method is a physics-driven supervised learning technique. We take advantage of the mass attenuation coefficient of dense materials compared to that of muscle tissues to perform a preliminary extraction of the dense material from the images using unsupervised methods. We then perform supervised deep learning on the images processed by the extracted dense material to obtain the final multi-material tissue map. The method is demonstrated on simulated breast models with calcifications as the dense material placed amongst the muscle tissues. The physics-guided machine learning method accurately decomposes the various tissues from input images, achieving a normalized root-mean-squared error of 2.75%.

Gopalakrishnan Meena, Murali↗

DOE OSTI2022

A Fast Time-Stepping Strategy for Dynamical Systems Equipped with a Surrogate Model

Simulation of complex dynamical systems arising in many applications is computationally challenging due to their size and complexity. Model order reduction, machine learning, and other types of surrogate modeling techniques offer cheaper and simpler ways to describe the dynamics of these systems but are inexact and introduce additional approximation errors. In order to overcome the computational difficulties of the full complex models, on one hand, and the limitations of surrogate models, on the other, this work proposes a new accelerated time-stepping strategy that combines information from both. This approach is based on the multirate infinitesimal general-structure additive Runge--Kutta framework. The inexpensive surrogate model is integrated with a small time step to guide the solution trajectory, and the full model is treated with a large time step to occasionally correct for the surrogate model error and ensure convergence. Here, we provide a theoretical error analysis, and several numerical experiments, to show that this approach can be significantly more efficient than using only the full or only the surrogate model for the integration.

Surrogate models↗

NASA NTRS1978

Cryogenic-coolant He-4-superconductor interaction

The thermodynamic and thermal interaction between a type 2 composite alloy and cryo-coolant He4 was studied with emphasis on post quench phenomena of formvar coated conductors. The latter were investigated using a heater simulation technique. Overall heat transfer coefficients were evaluated for the quench onset point. Heat flux densities were determined for phenomena of thermal switching between a peak and a recovery value. The study covered near saturated liquid, pressurized He4, both above and below the lambda transition, and above and below the thermodynamic critical pressure. In addition, friction coefficients for relative motion between formvar insulated conductors were determined.

Caspi, S.↗

NASA NTRS1987

Local intermodal energy transfer of the secondary instability in a plane channel

A mathematical technique for analyzing local energy-transfer rates among wave-vector triads is developed and applied to the data generated by direct numerical simulations of waves with various types of initial conditions. Starting the simulation with a primary two-dimensional wave and random noise produced structures very similar to those which evolved from three-dimensional center modes. The local transfer rates determined in this case help to explain the eventual deformation of the primary two-dimensional wave which was observed in wind-tunnel experiments. Including weak streamwise vortices in the initial flow field results in large amounts of energy being transferred to the K-type modes early in the simulation. The later development of the waves (and hence the energy-transfer rates) is similar to the previous case.

Singer, Bart A.↗

NASA NTRS1993

Adaptive data rate control TDMA systems as a rain attenuation compensation technique

Rainfall attenuation has a severe effect on signal strength and impairs communication links for future mobile and personal satellite communications using Ka-band and millimeter wave frequencies. As rain attenuation compensation techniques, several methods such as uplink power control, site diversity, and adaptive control of data rate or forward error correction have been proposed. In this paper, we propose a TDMA system that can compensate rain attenuation by adaptive control of transmission rates. To evaluate the performance of this TDMA terminal, we carried out three types of experiments: experiments using a Japanese CS-3 satellite with Ka-band transponders, in house IF loop-back experiments, and computer simulations. Experimental results show that this TDMA system has advantages over the conventional constant-rate TDMA systems, as resource sharing technique, in both bit error rate and total TDMA burst lengths required for transmitting given information.

Sato, Masaki↗

NASA NTRS2001

Modeling of Convective-Stratiform Precipitation Processes: Sensitivity to Partitioning Methods and Numerical Advection Schemes

Six different convective-stratiform separation techniques, including a new technique that utilizes the ratio of vertical and terminal velocities, are compared and evaluated using two-dimensional numerical simulations of a tropical [Tropical Ocean Global Atmosphere Coupled Ocean-Atmosphere Response Experiment (TOGA COARE)] and midlatitude continental [Preliminary Regional Experiment for STORM-Central (PRESTORM)] squall line. The simulations are made using two different numerical advection schemes: 4th order and positive definite advection. Comparisons are made in terms of rainfall, cloud coverage, mass fluxes, apparent heating and moistening, mean hydrometeor profiles, CFADs (Contoured Frequency with Altitude Diagrams), microphysics, and latent heating retrieval. Overall, it was found that the different separation techniques produced results that qualitatively agreed. However, the quantitative differences were significant. Observational comparisons were unable to conclusively evaluate the performance of the techniques. Latent heating retrieval was shown to be sensitive to the use of separation technique mainly due to the stratiform region for methods that found very little stratiform rain. The midlatitude PRESTORM simulation was found to be nearly invariant with respect to advection type for most quantities while for TOGA COARE fourth order advection produced numerous shallow convective cores and positive definite advection fewer cells that were both broader and deeper penetrating above the freezing level.

Lang, Steve↗

NASA NTRSDate not supplied

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs). This paper presents the guidance and control design and analysis for a mechanically-deployed DEV with a symmetric aeroshell and aerodynamic control surfaces. We present guidance tuning using both bank angle modulation with the Fully-Numerical Predictor Corrector Entry Guidance technique (FNPEG) and angle of attack and sideslip modulation with FNPEG with uncoupled range control (FNPEG URC). We show the control system design and simulation results for tracking both types of guidance commands.

Benjamin W L Margolis↗

NASA NTRS2021

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

Benjamin Margolis↗

NASA NTRS1992

A dynamic study of fragmentation and energy loss during high velocity impact

Research conducted under this contract can be divided into two main areas: hypervelocity (in the range up to 7 km/s) and high velocity (less than 1 km/s). Work in the former was performed at NASA-MSFC using the Light Gas Gun Facility. The lower velocity studies were conducted at Auburn University using the ballistic gun. The emphasis of the project was on the hypervelocity phenomenon especially in the characterization of the debris cloud formed by the primary impact events. Special devices were made to determine the angular distributions of momentum and energy of the debris cloud as a function of impact conditions. After several iteration processes, it was decided to concentrate on the momentum effort. Prototype devices were designed, fabricated, and tested. These devices were based on the conservation of momentum. Distributions of the debris cloud formed were measured by determining the amount of momentum transferred from the debris cloud to strategically placed pendulum measurement devices. The motion of the pendula was monitored using itegrated opto-interrupters. The distribution of momentum in the debris cloud was found to be a strong function of the impact condition. Small projectiles at high velocities were observed to produce finely dispersed debris whereas large projectiles generated discrete particles in the debris. Results also show that the momentum in the forward direction was enhanced due to the impact. This phenomenon of momentum multiplication was also observed in other studies and in computer simulations. It was initially planned to determine the energy distribution using deformation energy in a rod with strain gauges. Results from preliminary studies show that this technique is acceptable but too tedious. A new technique was explored based on measuring the heating effect of the debris cloud using an IR camera. The feasibility and sensitivity was established at Auburn University. This type of energy distribution measurement method can easily be adapted to the gas gun facility at MSFC. The objective of the lower velocity studies at Auburn was to simulate the damage produced in advanced materials by the lower energy debris cloud.

Zee, Ralph H.↗

NASA NTRS2013

Adams-Based Rover Terramechanics and Mobility Simulator - ARTEMIS

The Mars Exploration Rovers (MERs), Spirit and Opportunity, far exceeded their original drive distance expectations and have traveled, at the time of this reporting, a combined 29 kilometers across the surface of Mars. The Rover Sequencing and Visualization Program (RSVP), the current program used to plan drives for MERs, is only a kinematic simulator of rover movement. Therefore, rover response to various terrains and soil types cannot be modeled. Although sandbox experiments attempt to model rover-terrain interaction, these experiments are time-intensive and costly, and they cannot be used within the tactical timeline of rover driving. Imaging techniques and hazard avoidance features on MER help to prevent the rover from traveling over dangerous terrains, but mobility issues have shown that these methods are not always sufficient. ARTEMIS, a dynamic modeling tool for MER, allows planned drives to be simulated before commands are sent to the rover. The deformable soils component of this model allows rover-terrain interactions to be simulated to determine if a particular drive path would take the rover over terrain that would induce hazardous levels of slip or sink. When used in the rover drive planning process, dynamic modeling reduces the likelihood of future mobility issues because high-risk areas could be identified before drive commands are sent to the rover, and drives planned over these areas could be rerouted. The ARTEMIS software consists of several components. These include a preprocessor, Digital Elevation Models (DEMs), Adams rover model, wheel and soil parameter files, MSC Adams GUI (commercial), MSC Adams dynamics solver (commercial), terramechanics subroutines (FORTRAN), a contact detection engine, a soil modification engine, and output DEMs of deformed soil. The preprocessor is used to define the terrain (from a DEM) and define the soil parameters for the terrain file. The Adams rover model is placed in this terrain. Wheel and soil parameter files can be altered in the respective text files. The rover model and terrain are viewed in Adams View, the GUI for ARTEMIS. The Adams dynamics solver calls terramechanics subroutines in FORTRAN containing the Bekker-Wong equations.

Trease, Brian P.↗

NASA NTRS2022

Acoustic Modeling of Novel Over-The-Rotor Acoustic Liner Concepts Using COMSOL Multiphysics Simulation Software

This paper presents simulation predictions of novel over-the-rotor acoustic liner configurations compared with experimental data. This is a follow on to the investigation on the effect of grazing flow on grooved over-the-rotor casing treatments. The purpose of this modeling investigation stems from the determination that traditional liner modeling techniques are inadequate for nontraditional internal liner cavity geometries. A series of these expansion chamber type liner design concepts were previously developed by Glenn Research Center and tested using the Langley Research Center Normal Incidence Tube. The measured normalized impedance and absorption coefficient is compared with that obtained from the COMSOL Multiphysics® simulation. Additionally, using a parametric case study, another series of simulations were conducted to determine what additional benefits, if any, this genre of liner has to offer the acoustics community. A total of 53 permutations of this concept was investigated. The results indicate that with longer internal fins, the resonance is sifted to lower frequencies.

Acoustics↗

NASA NTRS2022

Free Energy Landscapes for Elucidating the Structural Consequences of Exon-20 mutations on the ErbB Family of Protein Kinases

The ErbB family of protein kinases plays an important role in major cellular functions and consequently mutations in the functional regions of these proteins are implicated in several types of cancer growths. To envision rational design of small molecule drugs that target the diseased proteins it is important to quantify the structural effects of the mutations, as some of these mutants render the protein resistant to tyrosine kinase inhibitors (TKIs). Herein we use advanced sampling techniques and long-timescale molecular dynamics simulations to predict the effect of major exon 20 mutations on the ErbB family, specifically EGFR and HER2 proteins. Exon 20 mutations have been clinically known to induce TKI resistance, though the mechanisms of such an effect is poorly understood. By mapping out the free energy landscape of the mutants and comparing them against the wild-type, we elucidate the structural differences in the binding pocket region that alter the nature of drug-protein interactions. We believe that these insights will play a pivotal role in developing small molecule drugs that overcome the TKI resistance.

Ashwin Ravichandran↗