Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

SiC Substrate Composition Effect on TGO Scale Growth in EBC Systems During High‐Temperature Steam Exposure

A systematic investigation was conducted on the oxidation behavior of silicon-bond coats within environmental barrier coating (EBC) systems applied to Si-carbide (SiC) substrates, aiming to understand how different underlying SiC substrates influence the bond coat's thermally grown oxide (TGO) and its properties. The study examined (Y/Yb) 2 Si 2 O 7 /Si coatings on three cost-effective surrogate SiC substrates (chemical vapor deposition [CVD]-grown β-SiC, sintered α-SiC, and reaction-bonded [RB] SiC) for SiC fiber /SiC matrix ceramic matrix composites (CMCs). Discrepancies in TGO growth were observed, with noticeably higher growth rates reported for the coated CMC specimens than for the four monolithic SiC specimens. The CMC samples produce an amorphous TGO, whereas the other monolithic substrates formed a crystalline TGO, which lowered the oxygen permeability through the SiO 2 scale. In conclusion, the vitrification of the TGO in the (Y/Yb) 2 Si 2 O 7 /Si/CMC system resulted from the migration of boron species from the CMC substrate to the SiO 2 scale, leading to network modification via boron doping.

EBC↗
DOE OSTI2022

Microstructural dependence of defect formation in iron-oxide thin films

In this report passivating iron-oxide films are grown atop iron films simulating the corrosion process in a nuclear reactor environment. Two oxide films grown via physical vapor deposition at 600 °C and room temperature exhibited dense-epitactic and columnar-polycrystalline, microstructures respectively. A third oxide film grown in open air at 600 °C exhibited an eqiuaxed, porous morphology. Cubic maghemite and magnetite phases in each oxide film were identified via grazing incidence X-ray diffraction. Positron annihilation spectroscopy was used to characterize point defects and measure their depth and size distributions in each oxide layer and showed a range of average positron lifetimes from 0.23 ns in the high temperature, vapor deposited film, 0.35 ns in the room temperature-grown film, and 0.31 ns in the thermally grown oxide. These data indicate that the film morphology, which varies greatly in these films, leads to very different defect content. Finally, four-dimensional scanning transmission electron microscopy was used to measure the internal stress of each film and was correlated to the strain state presented in the X-ray diffraction spectra. The defect formation in each film is reasoned through using a thin film growth model.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Stabilization of Ultrasmall Platinum Nanoparticles by Nitrogen-Doped Carbon: Implications for Catalysis and Electrocatalysis

Heterogeneous materials comprising platinum nanoparticles on carbon supports have numerous applications including fuel cell electrodes and heterogeneous catalysts. The effective application of these materials for fuel cells and catalysis will be greatly advanced by the ability to control the oxidation and sintering of the nanoparticles by modifications of the carbon support. One attempt of such control has been doping carbon supports with nitrogen. Here, in this work, a cutting-edge, high-sensitivity, in situ XRD instrument, which allows observation of ultrasmall Pt nanoparticles, has been combined with in situ XPS to provide unprecedented clarity in the characterization of supported Pt nanoparticles in oxidizing and high-temperature environments. On a nitrogen-doped carbon support derived from poly-phenylporphyrin, Pt nanoparticles show increased stability to oxidation and thermal sintering. The enhanced Pt–support interaction arising from the N dopant versus the N-free carbon is manifested by (1) decreased initial Pt particle sizes, (2) small particle size at higher surface densities, (3) increased resistance of Pt nanoparticles to oxidation, (4) increased electron binding energy of Pt0, and (5) increased resistance of Pt nanoparticles to sintering. It is expected that the higher stability of Pt on NC will be manifested in higher activity in fuel cells and high-temperature catalytic reactions.

catalytic reactions↗
DOE OSTI2024

MR&R Strategic Investments Review: OREATE (Oxide Reduction by Electrochemical Amalgamation and Thermal Extraction) [Slides]

The goal of this project is to develop a new process for metal recovery and recycle based on OREATE (Oxide Reduction by Electrochemical Amalgamation and Thermal Extraction). OREATE will be able to efficiently transform PuO 2 into metal (e.g., Pu-242) as well as recover and recycle actinide and rare earth metals after chlorination. The main objectives for FY24 are to complete the TRL assessment of the OREATE process and to achieve a throughput increase, transitioning from mg to gram quantities of metal.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Supersonic hot jet ablative testing and analysis of boron nitride nanotube hybrid composites

Boron nitride nanotubes (BNNTs) are high-strength, high-modulus nanotubes with high thermal and oxidative stabilities. Two hybrid composites were prepared with satin weave carbon fiber (CF) and resole-type phenolic resin: one with surface layers of BNNTs and one with alternating interlayers of BNNTs. The samples were subjected to hot jet tests that simulate realistic high-pressure-temperature conditions to understand the behavior of BNNTs under high-pressure erosion. Adding BNNTs to CF/phenolic laminates enhanced the ablation resistance by reinforcing the char material and mitigated localized thermal damage. Hybrid laminates exhibited up to 14% lower weight loss, 55% increase in flexural modulus, higher thermal diffusivity, and improved char yield and microstructure compared to CF/phenolic samples. The surface layer hybrid had many surviving nanotubes reinforcing the char and crystalline oxide structures that could mitigate further oxygen diffusion. Further, various characterization methods were used to deduce possible mechanisms and their products, indicating that BNNTs could serve as growth templates for direct crystalline boron oxide formation. Overall, hybrid BNNT/CF/phenolic laminates displayed better ablation resistance and favorable microstructure evolution under high-pressure conditions.

42 ENGINEERING↗
DOE OSTI2025

Complete Initial Studies in Microstructural Studies of Nuclear Graphite

Nuclear graphite is a critical material for the performance and safety of high-temperature reactors, making its study essential for the successful deployment of next-generation reactors in the United States. During the past year, Oak Ridge National Laboratory (ORNL) has contributed extensively to advancing the understanding of nuclear graphite’s properties, behavior, and applications; particular focus has been given to irradiation effects, oxidation mechanisms, thermal and mechanical performance, and long-term stability under reactor conditions. This report provides an update on the ongoing publications being prepared at ORNL. These studies are collectively intended to build a comprehensive knowledge base on nuclear graphite. The studies focus on key aspects such as microstructural characterization, oxidation behavior, advanced analytical techniques, molten salt infiltration, technique development, and billet-to-billet variability. By summarizing the progress of these publications, this report outlines ORNL’s contributions to the field, identifies knowledge gaps, and proposes future research directions. The findings presented in these studies will help enhance the understanding of nuclear graphite’s behavior, support the qualification of nuclear graphite materials, further the development of new techniques and guidelines for using microscopy techniques, and improve reactor safety and performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Low-temperature oxidation pathways are critical to thermal incineration of PFAS-laden materials

With growing desire to destroy per- and poly-fluoroalkyl substances (PFAS) now known to be detrimental to human health, a sound understanding of fluorocarbon combustion chemistry is important to efficient thermal destruction within incinerators. While most fluorocarbon combustion models and the sets of reactions contained within them were originally developed for the high temperatures encountered in flame suppression applications, they have often been used to assess PFAS destruction in incinerators, which emphasize a lower range of temperatures. We present results that demonstrate that low-temperature fluorocarbon oxidation pathways—not yet known to play a role in fluorocarbon combustion—impact key incinerator performance metrics, including: PFAS surrogate mole fractions, products of incomplete destruction, and waste destruction efficiencies. The results further point to the utility of NO as a potential additive. The present results show the influence of these pathways for CF 3 O 2 , for which some data are available, but analogous pathways would also occur for other fluoroalkylperoxy radicals, for which little is known. Furthermore, the results demonstrate the need for future work to identify and characterize low-temperature pathways more generally, consider such pathways in kinetic model development, and experimentally probe intermediate temperature conditions to better understand, design, and control thermal destruction technologies for improved PFAS management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

REFRACTORY COMPACT HEAT EXCHANGERS WITH EMBEDDED SENSORS ENABLED BY HYBRID ADVANCED SINTERING AND ADDITIVE APPROACH

Structural health monitoring (SHM) of compact heat exchangers (CHXs) operating in extreme environments is essential for ensuring system reliability, safety, and longevity. This study presents the development of high-temperature sensors fabricated via aerosol jet printing (AJP) using platinum ink, selected for its exceptional thermal stability, oxidation resistance, and electrical conductivity. AJP enables precise deposition of fine-feature sensor patterns onto complex geometries, making it well-suited for integration within CHX architectures. To enhance sensor durability, an alumina-based ceramic protective layer was printed over the platinum sensing elements. The sensors demonstrated stable, repeatable performance up to 900?°C during extended thermal cycling. A custom test setup was developed to evaluate sensor accuracy and robustness under steady-state and transient conditions. Substrate screening identified HG-1 ceramic-coated stainless steel as the most effective platform, offering strong adhesion and low resistance. Furthermore, electric field-assisted sintering (EFAS) was employed to embed the sensors into stainless steel 316L matrices without degrading their functionality. Post-embedding electrical tests confirmed sensor integrity, and initial characterization suggests strong potential for in-situ monitoring. This work provides a scalable strategy for integrating high-performance temperature sensors directly into refractory components, advancing embedded SHM technologies for harsh operating environments.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Accelerated oxidation during 1350°C cycling of ytterbium silicate environmental barrier coatings

We report environmental barrier coatings (EBCs) will be needed to protect SiC-based ceramic matrix composite components for the next generation of high-efficiency industrial gas turbines (IGTs). The IGT application will require ≥25 kh lifetimes, and little data are available on EBC failure mechanisms, particularly at ≥1300°C. Initial 1-h furnace cycle testing at 1350°C in 90 vol% H 2 O/10 vol% air was conducted ≥1000 cycles on thermally sprayed ytterbium disilicate (YbDS) coatings with and without an Si bond coating. By ≥1000 h, both EBCs formed thick, highly cracked, and fully crystalline cristobalite scales. Comparison of thermally grown oxide (TGO) microstructure and kinetics to isothermal rates of Si and SiC steam oxidation indicated a departure from slow-growing parabolic growth to more rapid rates of silica formation. Possible mechanisms and implications for this acceleration are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Intra-crystalline mesoporous zeolite encapsulation-derived thermally robust metal nanocatalyst in deep oxidation of light alkanes

Zeolite-confined metal nanoparticles (NPs) have attracted much attention owing to their superior sintering resistance and broad applications for thermal and environmental catalytic reactions. However, the pore size of the conventional zeolites is usually below 2 nm, and reactants are easily blocked to access the active sites. Herein, a facile in situ mesoporogen-free strategy is developed to design and synthesize palladium (Pd) NPs enveloped in a single-crystalline zeolite (silicalite-1, S-1) with intra-mesopores (termed Pd@IM-S-1). Pd@IM-S-1 exhibited remarkable light alkanes deep oxidation performances, and it should be attributed to the confinement and guarding effect of the zeolite shell and the improvement in mass-transfer efficiency and active metal sites accessibility. The Pd–PdO interfaces as a new active site can provide active oxygen species to the first C–H cleavage of light alkanes. This work exemplifies a promising strategy to design other high-performance intra-crystalline mesoporous zeolite-confined metal/metal oxide catalysts for high-temperature industrial thermal catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

In-situ ETEM study of plasma-facing tungsten nanofuzz oxidation at atmospheric pressure: Microstructure evolution and substrate-free oxidation kinetics

To enable sustainable carbon-free fusion energy, managing reactor structural material degradation during normal operation as well as accident scenarios is vital. Tungsten (W) plasma-facing materials (PFMs) are susceptible to aggressive high-temperature oxidation during air-ingress fusion reactor accidents, yet there's a lack of oxidation kinetic data for irradiated tungsten. Here, in this study, we utilize atmospheric environmental transmission electron microscopy (ETEM) to present the first kinetic data for substrate-free W nanofuzz oxidation at 400 ºC and 500 ºC in 1 bar dry air. Comparison with pristine bulk W during the early parabolic stage suggests an irradiationdecelerated oxidation for W nanofuzz. Our time-resolved in-situ characterization reveals a durable amorphous surface oxide, likely promoted by high-flux He + irradiation-induced surface defects, serving as an effective passivating layer that impedes nanofuzz oxidation onset. This surface oxide layer also interfaces well with newly formed orthorhombic WO 3 , facilitated by stress relief through He bubble shrinkage, providing lasting passivating protection throughout the nanofuzz parabolic oxidation. This new finding challenges conventional notions of irradiation's negative impact on metal oxidation, and calls for advanced characterization to enhance our understanding of fusion energy materials degradation, informed by further accident modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thickness-Independent Vibrational Thermal Conductance across Confined Solid-Solution Thin Films

In this study, we experimentally show that the thermal conductance across confined solid-solution crystalline thin films between parent materials does not necessarily lead to an increase in thermal resistances across the thin-film geometries with increasing film thicknesses, which is counterintuitive to the notion that adding a material serves to increase the total thermal resistance. Confined thin epitaxial Ca 0.5 Sr 0.5 TiO 3 solid-solution films with systematically varying thicknesses in between two parent perovskite materials of calcium titanate and (001)-oriented strontium titanate are grown, and thermoreflectance techniques are used to accurately measure the thermal boundary conductance across the confined solid-solution films, showing that the thermal resistance does not substantially increase with the addition of solid-solution films with increasing thicknesses from ~1 to ~10 nm. Contrary to the macroscopic understanding of thermal transport where adding more material along the heat propagation direction leads to larger thermal resistances, our results potentially offer experimental support to the computationally predicted concept of vibrational matching across interfaces. This concept is based on the fact that a better match in the available heat-carrying vibrations due to an interfacial layer can lead to lower thermal boundary resistances, thus leading to an enhancement in thermal boundary conductance across interfaces driven by the addition of a thin “vibrational bridge” layer between two solids.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of temperature on abrasion erosion in particle based concentrating solar powerplants

The use of solid particles as a heat transfer medium is being explored for concentrated solar power plants (CSP) to increase their efficiency by achieving operating temperature >700 °C. During operation, these hot particles are expected to move along the various components within the collector system, resulting in material degradation from a combination of high-temperature oxidation and erosion. In the present study, the performance of candidate materials was evaluated through a series of abrasion erosion experiments at room temperature as well as at 800 °C. Wear in metallic and refractory type materials was investigated using CarboBead® HSP 40/70 particles inside a resistance heated kiln. Furthermore, cross-sectional scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) analysis on the specimens tested at 800 °C determined that the specific wear rate in Inconel 740H and stainless steel 316 metallic specimens was influenced by the thermally grown oxide morphology. High chromium Inconel 740H specimens exhibited greater resistance to wear with a steady state specific wear rate of 1.92E-4 mm 3 N -1 m –1 compared to 5.7E-3 mm 3 N -1 m –1 for Stainless Steel 316.

14 SOLAR ENERGY↗
DOE OSTI2020

Divanadium substituted keggin [PV 2 W 10 O 40 ] on non-reducible supports-Al 2 O 3 and SiO 2 : synthesis, characterization, and catalytic properties for oxidative dehydrogenation of propane

Molecular metal oxide cluster, K 5 [α-1,2-PV 2 W 10 O 40 ] (PV 2 W 10 ), was found to have intrinsic catalytic activity for the oxidative dehydrogenation of propane with high selectivity (> 80%) to propylene at low propane conversion (0.3%). Synthesis of dispersed PV 2 W 10 in non-reducible supports, γ-Al 2 O 3 and SiO 2 , was done by incipient wetness impregnation. The supported catalysts were characterized by IR, Raman spectroscopy, nitrogen adsorption, x-ray powder diffraction (PXRD), elemental analysis, hydrogen temperature-programmed reduction (H 2 –TPR), and ammonia temperature-programmed desorption (NH 3 –TPD). Catalytic testing of the supported PV 2 W 10 at equimolar cluster concentration revealed that when supported in γ-Al 2 O 3 it is more active (sevenfold increase in propane conversion) but in SiO 2 it is more selective to propylene (94%). The observed performance was due to both an increase in reducibility and higher concentration of strong acid sites for PV 2 W 10 supported in γ-Al 2 O 3 versus SiO 2 . Lastly, PV 2 W10 was shown to remain intact under reaction conditions indicating its thermal and oxidative stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The distribution and selective decontamination of carbon-14 from nuclear graphite

This work investigates 14 C release behaviour from UK Magnox reactor sourced irradiated graphite under relatively low temperature oxidation conditions: a 1% oxygen in argon atmosphere at temperatures ranging from 600°C to 700°C, and durations from 4 to 120 hours. A method is used for construction of a detailed 14 C release profile with mass loss. The 14 C release profile is predictable between samples, and an empirical release profile is derived to predict releases to higher mass losses than in this work. An accelerated 14 C release rate at small mass losses is observed, indicative of a 14 C-enriched surface region with a depleting concentration gradient into the material, and the source terms and complexities associated with predicting where the 14 C arose from are discussed. Selective decontamination of a fraction of the 14 C is possible, with the limitation of a reducing efficiency with mass loss and time. This work demonstrates a method for determining the distribution of 14 C between near-surface regions and the bulk material in differing sources of irradiated graphite, and provides data in support of making an informed assessment for the adoption of low temperature thermal treatment and isotopic reduction of irradiated graphite wastes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Spark plasma sintering (SPS) densified U 3 Si 2 pellets: Microstructure control and enhanced mechanical and oxidation properties

Dense U 3 Si 2 pellets with controlled grain structure and enhanced thermal-mechanical and oxidation properties are synthesized with spark plasma sintering (SPS). Microstructure and phase composition of the SPS densified pellets are characterized systematically using SEM, EDS, and XRD. Thermal-mechanical properties and oxidation behavior of the sintered silicide fuel pellets are analyzed by laser flash, indentation, and dynamic thermogravimetric analysis. Dense U 3 Si 2 pellets are consolidated by combining high energy ball milling and rapid sintering by SPS, and the microstructure structures are controlled from micron-sized (~5.7 μm grain size) for conventional silicide to a nanocrystalline matrix with an average grain size of ~280 nm. A dominant phase of distorted U 3 Si 2 was identified with lattice expansion due to residual thermal stress upon SPS consolidation and rapid cooling processes. Both micron-sized and nano-sized pellets show exceptional thermal transport properties, consistent with monolithic silicides reported in literature. The SPS-densified pellets possess simultaneously high hardness and fracture toughness. The SPS-densified silicide pellets also demonstrate exceptional oxidation performance with extended onset oxidation temperature above 500 °C and reduced oxidation kinetics, particularly for nano-sized pellets. A strong strain effect was proposed in which compressive stress in nano-sized pellets enhances the oxidation resistance of silicide fuels, as evidenced by the degradation of oxidation performance upon strain relaxation by isothermal annealing. The correlation among the sintering process – microstructure control – physical properties and fuel behavior is established. A new concept of strain engineering is proposed further properties optimization, enabling the development of potential oxidation and corrosion-resistant silicides with extended performance, the key technological challenge of U 3 Si 2 as the leading concept of accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Rapid Identification of Synthetic Routes to Functional Metastable Phases Using X-ray Probed Laser Anneal Mapping (XPLAM) Time-Temperature Quench Maps

Many material systems have known or predicted functional phases that are metastable at standard temperature and pressure. While substantial advances have been made in the high-throughput and combinatorial synthesis of materials with a range of stoichiometries, investigation of thermal processing remains largely the domain of iterative uniform anneals or static gradients. Here we develop X-ray probed laser anneal mapping (XPLAM), a high throughput technique coupling spatially resolved X-ray diffraction with microsecond to millisecond laser gradient anneals to produce temperature–dwell–transformation (TDT) diagrams of the phase as a function of quench time and temperature. In addition to showing regimes where specific metastable phases form preferentially, TDT diagrams provide insight into the submillisecond kinetics of solid–solid phase transitions. This is a unique tool for mapping reaction pathways for metastable phases. As a first demonstration of XPLAM, we study Bi2O3, which has a rich set of polytypes, including the d-phase with an exceptionally high oxygen ion conductivity. We demonstrate the first annealing-driven synthesis of room temperature d-Bi2O3. We expect XPLAM to prove a powerful technique for rapid identification of synthetic routes to metastable phases and to generate the exhaustive data sets required for machine learning-guided exploration of materials processing.

36 MATERIALS SCIENCE↗