Search NASA⌕ Search

SEARCH · Search NASA

Results for “FAILURE MODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

JANTX2N2484 transistor

Report evaluates effects of power and temperature overstress on Raytheon and Teledyne devices. Power overstress produced few failures. Both lots of devices exceeded 50 percent failure at 250 deg C. Failure modes are evaluated.

Source record↗

JANTX2N2905A transistor

Report evaluates effects of power and temperature overstress on Motorola and Texas Instruments devices. A variety of failure modes are described.

Source record↗

JANTX2N2920 Dual transistor

Report describes effects of power and temperature overstress on Fairchild and National Semiconductor devices. 160 hour temperature stress was only test to cause notable damage. Loss of gain is principal failure mode.

Source record↗

JANTX2N4856 field-effect transistor

Report evaluates effects of power and temperature overstress on Teledyne and Texas Instruments devices. Temperature stress caused most failures for both manufacturers' lots. Failure modes are analyzed.

Source record↗

Toggled signal for prevention of control errors

Redundant command lines use two different "true" signals to avoid common failure modes. When function is required to operate, computer generates command and transmits it to demultiplexer, where it is split along two paths, producing outputs from separate electronic cards. Outputs combine to drive AND gate high and begin function.

Wyllie, C. E.↗

Materials and structures technology

Materials and structures performance limitations, particularly for the hot section of the engine in which these limitations limit the life of components, are considered. Failure modes for components such as blades, vanes, and combustors and how they are affected by the environment for such components are discussed. Methods used to improve the materials used for such components are: (1) application of directional structures to turbine components for high strength at high temperatures; (2) improved coatings to increase oxidation and corrosion resistance; (3) increase strength and stiffness with reduced weight by applying higher specific properties of composite materials; and (4) cost effective processing such as near net shape powder methods applied to disks. Life prediction techniques developed to predict component life accurately in advance of service and progress in improving the intermediate and cold section components of turbine engines are covered.

Signorelli, R. A.↗

Design, durability and low cost processing technology for composite fan exit guide vanes

A lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application was investigated. Eight candidate material/design combinations were evaluated by NASTRAN finite element analyses. A total of four combinations were selected for further analytical evaluation, part fabrication by two ventors, and fatigue test in dry and wet condition. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation, and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Pre-test and post-test microstructural examination and nondestructive analyses were conducted to determine the effect of material variations on fatigue durability and failure mode. Relevant data were acquired with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits, and part price of the composite fan exit guide vane.

Blecherman, S. S.↗

Modified aerospace reliability and quality assurance method for wind turbines

The safety, reliability, and quality assurance (SR&QA) approach developed for the first large wind turbine generator project is described. The SR&QA approach was used to assure that the machine would not be hazardous to the public or operating personnel, would operate unattended on a utility grid, would demonstrate reliable operation and would help establish the quality assurance and maintainability requirements for future wind turbine projects. A modified failure modes and effects analysis during the design phase, minimal hardware inspections during parts fabrication, and three simple documents to control activities during machine construction and operation were presented.

Klein, W. E.↗

Predicting the time-temperature dependent axial failure of B/A1 composites

Experimental and theoretical studies were conducted in order to understand and predict the effects of time, temperature, and stress on the axial failure modes of boron fibers and B/A1 composites. Due to the anelastic nature of boron fiber deformation, it was possible to determine simple creep functions which can be employed to accurately describe creep and fracture stress of as-produced fibers. Analysis of damping and strength data for B/6061 A1 composites indicates that fiber creep effects of creep on fiber fracture are measurably reduced by the composite fabrication process. The creep function appropriate for fibers with B/Al composites was also determined. A fracture theory is presented for predicting the time-temperature dependence of the axial tensile strength for metal matrix composites in general and B/A1 composites in particular.

Dicarlo, J. A.↗

Meteoroid protection for the Comet Halley probe

The high closing speed of 57km/s between the spacecraft and Halley poses special problems in the design of the required meteoroid protection. A double wall structure with a total thickness equal to 0.1 to 1 times the diameter of the largest meteoroid encountered is sufficient to stop that meteoroid. However, the unusually high number of meteoroid impacts on the Halley probe will cause significant erosion of the outer wall so that failure of the second wall is more likely to occur from a small meteoroid passing through a previously created hole in the outer wall and then penetrating the second wall. Calculations of the shielding required based on this failure mode, show that a double wall structure must actually have a total thickness 1.2 to 7.3 times the diameter of the largest meteoroid encountered, depending on the size distribution of the meteoroids.

Humes, D.↗

Nonlinear temperature dependent failure analysis of finite width composite laminates

A quasi-three dimensional, nonlinear elastic finite element stress analysis of finite width composite laminates including curing stresses is presented. Cross-ply, angle-ply, and two quasi-isotropic graphite/epoxy laminates are studied. Curing stresses are calculated using temperature dependent elastic properties that are input as percent retention curves, and stresses due to mechanical loading in the form of an axial strain are calculated using tangent modulii obtained by Ramberg-Osgood parameters. It is shown that curing stresses and stresses due to tensile loading are significant as edge effects in all types of laminate studies. The tensor polynomial failure criterion is used to predict the initiation of failure. The mode of failure is predicted by examining individual stress contributions to the tensor polynomial.

Nagarkar, A. P.↗

Concepts and techniques for ultrasonic evaluation of material mechanical properties

Ultrasonic methods that can be used for material strength are reviewed. Emergency technology involving advanced ultrasonic techniques and associated measurements is described. It is shown that ultrasonic NDE is particularly useful in this area because it involves mechanical elastic waves that are strongly modulated by morphological factors that govern mechanical strength and also dynamic failure modes. These aspects of ultrasonic NDE are described in conjunction with advanced approaches and theoretical concepts for signal acquisition and analysis for materials characterization. It is emphasized that the technology is in its infancy and that much effort is still required before the techniques and concepts can be transferred from laboratory to field conditions.

Vary, A.↗

Effects of moisture on apparent flexure strength and on torsion and flexure fatigue properties of graphite-epoxy composites

The effects of moisture and temperature on unidirectional and multi-ply laminates of T300/934 and AS/3501 graphite-epoxy systems were investigated. Properties studied were static flexure strength and flexure and torsion fatigue strengths at room temperature and at 74 C. Specimens with increased moisture content showed a reduced static flexure strength; water as the test environment had only a negligible influence. In flexure fatigue and torsion fatigue, the water environment caused somewhat reduced fatigue strengths at room temperature and significantly greater degradation in 74 C water. The failure mode in all cases was interlaminar delamination.

Sumsion, H. T.↗

An analysis of delamination in angle-ply fiber-reinforced composites

A study of the mechanics and failure modes of delamination initiated from a surface flaw in angle-ply fiber-reinforced composites is presented. The analysis employs a hybrid-stress finite-element method including a crack-tip singular element with its field variables expressed by Muskhelishvili's complex stress functions. Solutions are obtained for the delaminated composites with various laminate parameters. The results elucidate unique and important characteristics of delamination crack-tip response and interlaminar stress transfer mechanisms. Of particular interest are the mixed-mode stress-intensity factors associated with the delamination crack. The influence of ply orientation on KI and KII and their effects on subsequent crack extension are discussed.

Wang, S. S.↗

Predicting the time-temperature dependent axial failure of B/Al composites

Theoretical and experimental studies are reviewed whose objective was to gain insight into and predict the effects of time, temperature, and stress on the axial failure modes of boron fibers and B/Al composites. Owing to the inelastic nature of boron fiber deformation, it proved possible to develop simple creep functions which can be used to describe accurately the creep and fracture stress of as-produced fibers. Analysis of damping and stress data for B/6061 Al composites indicates that fiber creep and the effects of creep of fiber fracture are measurably reduced by the composite fabrication process.

Dicarlo, J. A.↗

Modified aerospace R&QA method for wind turbines

This paper describes the Safety, Reliability and Quality Assurance (SR&QA) approach developed for the first large wind turbine generator project, MOD-OA. The SR&QA approach to be used had to assure that the machine would not be hazardous, would operate unattended on a utility grid, would demonstrate reliable operation, and would help establish the quality assurance and maintainability requirements for wind turbine projects. The final approach consisted of a modified Failure Modes and Effects Analysis (FMEA) during the design phase, minimal hardware inspections during parts fabrication, and three documents to control activities during machine construction and operation.

Klein, W. E.↗

Refine your search to explore more results.