Search NASA⌕ Search

SEARCH · Search NASA

Results for “Metal Loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

The isothermal fatigue behavior of a unidirectional SiC/Ti composite and the Ti alloy matrix

The high temperature fatigue behavior of a metal matrix composite (MMC) consisting of Ti-15V-3Cr-3Al-3Sn(Ti-15-3) matrix reinforced by 33 volume percent of continuous unidirectional SiC fibers was experimentally and analytically evaluated. Isothermal MMC fatigue tests with constant amplitude loading parallel to the fiber direction were performed at 300 and 550 C. Comparative fatigue tests of the Ti-15-3 matrix alloy were also performed. Composite fatigue behavior and the in situ stress state of the fiber and matrix were analyzed with a micromechanical model, the Concentric Cylinder Model (CCM). The cyclic stress-strain response of the composite was stable at 300 C. However, an increase in cyclic mean strain foreshortened MMC fatigue life at high strain ranges at 550 C. Fatigue tests of the matrix alloy and CCM analyses indicated this response was associated with stress relaxation of the matrix in the composite and subsequent load shedding to the fibers.

Gayda, John↗
NASA NTRS1992

Screen Cage Ion Plating (SCIP) and scratch testing of polycrystalline aluminum oxide

A screen cage ion plating (SCIP) technique was developed to apply silver films on electrically nonconducting aluminum oxide. It is shown that SCIP has remarkable throwing power; surfaces to be coated need not be in direct line of sight with the evaporation source. Scratch tests, employing a diamond stylus with a 200 micro m radius tip, were performed on uncoated and on silver coated alumina. Subsequent surface analysis show that a significant amount of silver remains on the scratched surfaces, even in areas where high stylus load produced severe crack patterns in the ceramic. Friction coefficients were lowered during the scratch tests on the coated alumina indicating that this modification of the ion planting process should be useful for applying lubricating films of soft metals to electrical insulating materials. The very good throwing power of SCIP also strongly suggests general applicability of this process in other areas of technology, e.g., electronics, in addition to tribology.

Spalvins, Talivaldis↗
NASA NTRS2003

Test-Free Fracture Toughness

Computational simulation results can give the prediction of damage growth and progression and fracture toughness of composite structures. The experimental data from literature provide environmental effects on the fracture behavior of metallic or fiber composite structures. However, the traditional experimental methods to analyze the influence of the imposed conditions are expensive and time consuming. This research used the CODSTRAN code to model the temperature effects, scaling effects and the loading effects of fiberbraided composite specimens with and without fiber-optic sensors on the damage initiation and energy release rates. The load-displacement relationship and fracture toughness assessment approach is compared with the test results from literature and it is verified that the computational simulation, with the use of established material modeling and finite element modules, adequately tracks the changes of fracture toughness and subsequent fracture propagation for any fiberbraided composite structure due to the change of fiber orientations, presence of large diameter optical fibers, and any loading conditions.

Minnetyan, Levon↗
NASA NTRS2003

Test-Free Fracture Toughness

Computational simulation results can give the prediction of damage growth and progression and fracture toughness of composite structures. The experimental data from literature provide environmental effects on the fracture behavior of metallic or fiber composite structures. However, the traditional experimental methods to analyze the influence of the imposed conditions are expensive and time consuming. This research used the CODSTRAN code to model the temperature effects, scaling effects and the loading effects of fiber/braided composite specimens with and without fiber-optic sensors on the damage initiation and energy release rates. The load-displacement relationship and fracture toughness assessment approach is compared with the test results from literature and it is verified that the computational simulation, with the use of established material modeling and finite element modules, adequately tracks the changes of fracture toughness and subsequent fracture propagation for any fiber/braided composite structure due to the change of fiber orientations, presence of large diameter optical fibers, and any loading conditions.

Minnetyan, Levon↗
NASA NTRS2011

Proposal for Certifying Expandable Planetary Surface Habitation Structures

A factor-of-safety (FS) of 4.0 is currently used to design habitation structures made from structural soft goods. This approach is inconsistent with using a FS of 2.0 for metallic and polymeric composite pressure vessels as well as soft good structures such as space suits and parachutes. This inconsistency arises by using the FS to improperly account for the unknown effects of a variety of environmental and loading uncertainties. Using a 4.0 FS not only results in additional structural mass, it also makes it difficult to gain insight into the limitations of the material and/or product form and thus, it becomes difficult to make improvements. In order to bring consistency to the design and certification of expandable habitat structures, the approach used by the Federal Aviation Administration (FAA) to certify polymeric composite aircraft structures is used as a model and point of departure. A draft certification plan for Expandable Habitat Structures is developed in this paper and offered as an option for placing habitats made from soft goods on an equal footing with other structural implementations.

Dorsey, John T.↗
NASA NTRS2017

Nuclear Rocket Ceramic Metal Fuel Fabrication Using Tungsten Powder Coating and Spark Plasma Sintering

Nuclear thermal propulsion is an enabling technology for crewed Mars missions. An investigation was conducted to evaluate spark plasma sintering (SPS) as a method to produce tungsten-depleted uranium dioxide (W-dUO2) fuel material when employing fuel particles that were tungsten powder coated. Ceramic metal fuel wafers were produced from a blend of W-60vol% dUO2 powder that was sintered via SPS. The maximum sintering temperatures were varied from 1,600 to 1,850 C while applying a 50-MPa axial load. Wafers exhibited high density (>95% of theoretical) and a uniform microstructure (fuel particles uniformly dispersed throughout tungsten matrix).

Barnes, M. W.↗
DOE OSTI2021

Ternary borides and borohydrides for hydrogen storage and method of synthesis

A method and a system is provided for obtaining solid-state hydrogen storage and release in materials with at least theoretical loaded hydrogen densities of 11 wt % or greater that can deliver hydrogen and be recharged at moderate temperatures enabling incorporation into hydrogen storage systems suitable for transportation applications. These materials comprise ternary boride materials comprising certain light transition metals and alkaline or alkaline earth metals, and ideally have no or very little phase separation. A process of making these materials is also provided.

Stavila, Vitalie↗
DOE OSTI2023

Hydrogen Adsorption in Ultramicroporous Metal–Organic Frameworks Featuring Silent Open Metal Sites

In this work, we utilized an ultramicroporous metal–organic framework (MOF) named [Ni 3 (pzdc) 2 (ade) 2 (H 2 O) 4 ]·2.18H 2 O (where H 3 pzdc represents pyrazole-3,5-dicarboxylic acid and ade represents adenine) for hydrogen (H 2 ) adsorption. Upon activation, [Ni 3 (pzdc) 2 (ade) 2 ] was obtained, and in situ carbon monoxide loading by transmission infrared spectroscopy revealed the generation of open Ni(II) sites. The MOF displayed a Brunauer–Emmett–Teller (BET) surface area of 160 m 2 /g and a pore size of 0.67 nm. Hydrogen adsorption measurements conducted on this MOF at 77 K showed a steep increase in uptake (up to 1.93 mmol/g at 0.04 bar) at low pressure, reaching a H 2 uptake saturation at 2.11 mmol/g at ~0.15 bar. The affinity of this MOF for H 2 was determined to be 9.7 ± 1.0 kJ/mol. In situ H 2 loading experiments supported by molecular simulations confirmed that H 2 does not bind to the open Ni(II) sites of [Ni 3 (pzdc) 2 (ade) 2 ], and the high affinity of the MOF for H 2 is attributed to the interplay of pore size, shape, and functionality.

08 HYDROGEN↗
DOE OSTI2019

Understanding Nitrate Chemistry - The Key to Safer and More Efficient TRU Waste Acceptance - 19618

Investigations into the Waste Isolation Pilot Plant (WIPP) radiological release from a transuranic (TRU) waste drum concluded that the event was initiated by a thermal runaway, principally involving interactions between the polysaccharide-based kitty litter and nitric acid, which released radiological material along with hot gases and combustible materials from the drum. In this paper, the hazards of polysaccharides present as either starch based kitty litter or cellulose rags in a TRU waste drum exposed to nitric acid (and by extension metal nitrate salts) have been evaluated, based on considerations of how complex nitrogen redox cycles carry out the aqueous phase oxidation of alcohols and related organic functional groups. These exothermic reactions, coupled with a positive feedback loop inherent to nitrogen redox chemistry, can initiate an autocatalytic thermal runaway and explosive gas generation, which poses the most significant risk under ambient conditions where acidic solution may be present (in small quantities as free liquid or sorbed within a solid matrix). Nitric acid is an extremely potent oxidant but is itself remarkably inert, rarely interacting directly with oxidizable substrates and instead exerting its vast potential energy through lower oxidation state reactants such as nitrogen dioxide and nitrous acid that are generated from its slow self-decomposition. Nitrous acid is the reactant that carries out substrate oxidation, and systems that are not pre-loaded with nitrous acid will experience an induction period before significant reactivity commences. Under oxidizing fuel-lean conditions, nitrogen dioxide may induce autocatalytic nitrous acid formation, which may supplement additional side-reactions, potentially leading to thermal runaway. Therefore, the system is most vulnerable at the end of an induction period. Metal nitrate salts promote this ambient temperature solution chemistry (cf. traditional oxidizer properties of metal nitrate salts, which operate in the solid state at elevated temperatures) by releasing nitric acid into the system via hydrolysis. Unlike simple alcohols with a single hydroxyl functional group, the chemistry of polymeric carbohydrates (polysaccharides) such as starches and cellulose is more diverse. Therefore, the oxidation of the simple monomeric carbohydrate glucose is first examined to provide insight into the analogous reactivity with polysaccharides. Although less reactive than alcohols by virtue of extensive hydrogen bonding, carbohydrates are oxidized by nitric acid through the same fundamental mechanisms, complicated by a variety of competing side reactions including acid-catalyzed hydrolytic depolymerization to more reactive (ultimately monomeric) units, as well as other degradation reactions promoted by radical mechanisms. For this reason, polysaccharides such as starches that are more susceptible to hydrolysis are more reactive than cellulose, with the attendant microbial population in starch based kitty litter adding a special aspect of reactivity. From this safety evaluation, a bounding latency period has been developed beyond which a stored TRU waste drum that contains polysaccharides (starch based kitty litter excluded) commingled with nitric acid and/or metal nitrate salts may no longer present a hazard under ambient conditions, based on a compilation of induction periods and reaction times involving nitric acid with various oxidizable substrates under a variety of conditions from synthetic procedures, tests, and adverse incident scenarios. By obviating the need for costly treatment options or characterization, a better understanding of nitrate redox chemistry and the hazards it presents with polysaccharide oxidation thus provides a more efficient means to safely dispose of TRU waste generated within the Department of Energy (DOE) complex. (author)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Metal–Organic Framework-derived Atomic Metal Sites Promoting Sulfur Cathode for All-Solid-State Lithium–Sulfur Batteries

All-solid-state lithium–sulfur batteries (ASSLSBs) offer high energy density and intrinsic safety; however, they still face major challenges, including sluggish redox kinetics and poor sulfur utilization. Incorporating conductive materials into sulfur cathodes is an effective strategy to mitigate these limitations. Here, a highly conductive cobalt–nitrogen–doped carbon (Co–NC) derived from a metal–organic framework (MOF) is introduced to accelerate charge transfer and promote reversible sulfur conversion. Co−NC provides atomically dispersed Co–N sites and conductive carbon pathways that correlate with improved charge transfer, sulfur utilization, and rate capability. Co–NC@S cathode delivers 1499 mAh g–1 at C/20 with a high sulfur loading (5 mg cm–2) and retains 1292 mAh g–1 after five cycles (vs 443 mAh g–1 without Co–NC). Moreover, Co–NC derived ASSLSB achieves 903 mAh g–1 at 5C at 60 °C. This work provides a practical and effective approach to develop high energy, high-rate ASSLSBs.

25 ENERGY STORAGE↗
NASA NTRS1973

Evaluation of a metal shear web selectively reinforced with filamentary composites for space shuttle application. Phase 2: summary report: Shear web component fabrication

The fabrication of two shear web test elements and three large scale shear web test components are reported. In addition, the fabrication of test fixtures for the elements and components is described. The center-loaded beam test fixtures were configured to have a test side and a dummy or permanent side. The test fixtures were fabricated from standard extruded aluminum sections and plates and were designed to be reuseable.

Laakso, J. H.↗
NASA NTRS1993

An Application of a New Electromagnetic Sensor to Real-Time Monitoring of Fatigue Crack Growth in Thin Metal Plates

A major part of fracture mechanics is concerned with studying the initiation and propagation of fatigue cracks. This typically requires constant monitoring of crack growth during fatigue cycles which necessitates automation of the whole process. If the rate of crack growth can be determined the experimenter can vary externally controlled parameters such as load level, load cycle frequency and so on. Hence, knowledge of the precise location of the crack tip at any given time is very valuable. One technique currently available for measuring fatigue crack length is the DC potential drop method. The method, however, may be inaccurate if the direction of crack growth deviates considerably from what was assumed initially or the curvature of the crack becomes significant. Another approach is to digitize an optical image of the test specimen surface and then apply a pattern recognition technique to locate the crack tip, but this method is still under development. The present work is an initial study on applying eddy current-type probes to monitoring fatigue crack growth. The performance of two types of electromagnetic probes, a conventional eddy current probe and a newly developed self-nulling probe, was evaluated for the detection characteristics at and near the tips of fatigue cracks. The scan results show that the latter probe provides a very well defined local maximum in its output in the crack tip region suggesting the definite possibility of precisely locating the tip, while the former provides a somewhat ambiguous distribution of the sensor output in the same region. The paper is organized as follows: We start by reviewing the design and performance characteristics of the self-nulling probe and then describe the scan results which demonstrate the basic properties of the self-nulling probe. Next, we provide a brief description of the software developed for tracing a simulated crack and give a brief discussion of the main results of the test. The final section summarizes the major accomplishments of the present work and the elements of the future R&D needs.

Namkung, M.↗
DOE OSTI2019

Heterogeneities dominate mechanical performance of additively manufactured metal lattice struts

Architected structural metamaterials, also known as lattice, truss, or acoustic materials, provide opportunities to produce tailored effective properties that are not achievable in bulk monolithic materials. These topologies are typically designed under the assumption of uniform, isotropic base material properties taken from reference databases and without consideration for sub-optimal as-printed properties or off-nominal dimensional heterogeneities. However, manufacturing imperfections such as surface roughness are present throughout the lattices and their constituent struts create significant variability in mechanical properties and part performance. Here, this study utilized a customized tensile bar with a gauge section consisting of five parallel struts loaded in a stretch (tensile) orientation to examine the impact of manufacturing heterogeneities on quasi-static deformation of the struts, with a focus on ultimate tensile strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Understanding H 2 Evolution from the Decomposition of Dibutylmagnesium Isomers Using in-Situ X-ray Diffraction Coupled with Mass Spectroscopy

Alkylmagnesium compounds such as dibutylmagnesium can be effectively decomposed to produce MgH 2 and Mg metal for applications such as hydrogen storage, single site catalysis, and powder metallurgy or as the last step of comprehensive processes to produce Mg metal from magnesium salts. For these applications it is important to understand the decomposition reactions of dibutylmagnesium and to quantify its decomposition products. In this study, to avoid interference from air and moisture, an in situ X-ray diffraction (XRD) coupled with mass spectroscopy system was developed to investigate phase changes and released products in real time for the decomposition reactions. For the dibutylmagnesium (MgBu 2 n-n ) with two n -butyl groups, transformation to MgH 2 occurred at 250 °C and transformation to Mg metal occurred near 384 °C. The diffraction data suggest the possibility of an intermediate phase with one butyl group formed during the transformation to MgH 2 . Decomposition of MgH 2 under vacuum is accelerated by eliminating H 2 from the system as it is evolved. The sec- butyl n -butylmagnesium (MgBu 2 s-n ) was observed to decompose at as low as 50 °C, indicating the increased lability of the sec -butyl group in the dibutylmagnesium isomer. Thermogravimetric analysis (TGA) for the MgBu 2 n-n and MgBu 2 s-n loaded in air-free conditions recorded higher than 98% conversion to MgH 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Joining Dissimilar Materials via Rotational Hammer Riveting Technique

A mechanically robust joining method for Mg/Al and Mg/CFRP could enable multi-material assemblies that decrease vehicle weight while offering more flexibility for designers. However, certain challenges exist for joining Mg/Al and Mg/CFRP. Mechanical joining, such as conventional riveting, clinching and bolting do not form a metallurgical bond between the fastener and metal sheet being fastened. Large differences in physical and mechanical properties of metals and polymers make joining Al or Mg to CFRP challenging via various welding techniques. With solid-state and fusion based welding, rapid formation of brittle intermetallic compounds at the Mg/Al interface lead to interfacial fracture under mechanical loading. In this study, a Rotational Hammer Rivet (RHR) technique was developed to fabricate Mg/CFRP and Mg/Al joints. With RHR technique, direct joining between Mg/Al and Mg/CFRP were replaced by joining Mg rivet head and top Mg sheet. Through heat generated by plastic deformation of an Mg rivet, RHR creates a metallurgical bond between rivet head and Mg sheet which seals corrosive electrolyte from penetrating around the rivet head.

riveting, magnesium alloys, CFRP, Dissimilar Joini↗
DOE OSTI2016

Phase transformations at interfaces: Observations from atomistic modeling

Here, we review the recent progress in theoretical understanding and atomistic computer simulations of phase transformations in materials interfaces, focusing on grain boundaries (GBs) in metallic systems. Recently developed simulation approaches enable the search and structural characterization of GB phases in single-component metals and binary alloys, calculation of thermodynamic properties of individual GB phases, and modeling of the effect of the GB phase transformations on GB kinetics. Atomistic simulations demonstrate that the GB transformations can be induced by varying the temperature, loading the GB with point defects, or varying the amount of solute segregation. The atomic-level understanding obtained from such simulations can provide input for further development of thermodynamics theories and continuous models of interface phase transformations while simultaneously serving as a testing ground for validation of theories and models. They can also help interpret and guide experimental work in this field.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Anisotropy and Strain Localization in Dynamic Impact Experiments of Tantalum Single Crystals

Deformation mechanisms in bcc metals, especially in dynamic regimes, show unusual complexity, which complicates their use in high-reliability applications. Here, we employ novel, high-velocity cylinder impact experiments to explore plastic anisotropy in single crystal specimens under high-rate loading. The bcc tantalum single crystals exhibit unusually high deformation localization and strong plastic anisotropy when compared to polycrystalline samples. Several impact orientations - [100], [110], [111] and [1¯49] - are characterized over a range of impact velocities to examine orientation-dependent mechanical behavior versus strain rate. Moreover, the anisotropy and localized plastic strain seen in the recovered cylinders exhibit strong axial symmetries which differed according to lattice orientation. Two-, three-, and four-fold symmetries are observed. We propose a simple crystallographic argument, based on the Schmid law, to understand the observed symmetries. These tests are the first to explore the role of single-crystal orientation in Taylor impact tests and they clearly demonstrate the importance of crystallography in high strain rate and temperature deformation regimes. These results provide critical data to allow dramatically improved high-rate crystal plasticity models and will spur renewed interest in the role of crystallography to deformation in dynamics regimes.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Implementation and application of the peak scaling method for temperature measurement in the laser heated diamond anvil cell

In this work, a new design for a double-sided high-pressure diamond anvil cell laser heating set-up is described. The prototype is deployed at beamline 12.2.2 of the Advanced Light Source at Lawrence Berkeley National Lab. Our compact design features shortened mechanical lever arms, which results in more stable imaging optics, and thus more user friendly and more reliable temperature measurements based on pyrometry. A modification of the peak scaling method was implemented for pyrometry, including an iterative method to determine the absolute peak temperature, thus allowing for quasi-real time temperature mapping of the actual hotspot within a laser-heated diamond anvil cell without any assumptions on shape, size, and symmetry of the hotspot and without any assumptions to the relationship between fitted temperature and peak temperature. This is important since we show that the relationship between peak temperature and temperature obtained by fitting the Planck function against the thermal emission spectrum averaged over the entire hotspot is not constant but depends on variable fitting parameters (in particular, the size and position of the fitting window). The accuracy of the method is confirmed through measuring melting points of metal wires at ambient pressure. Having absolute temperature maps in real time allows for more differentiated analyses of laser heating experiments. Finally, we present such an example of the pressure variations within a heated hotspot of AgI at a loaded base pressure of 3.8 GPa.

42 ENGINEERING↗

Refine your search to explore more results.