Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alloy powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Thermal stability of additively manufactured austenitic 304L ODS alloy

Thermal stability and high-temperature mechanical properties of a 304L austenitic oxide dispersion strengthened (ODS) alloy manufactured via laser powder bed fusion (LPBF) are examined in this work. Additively manufactured 304L ODS alloy samples were aged at temperatures of 1000, 1100, and 1200 °C for 100 h in an argon atmosphere. Microstructure characterization of LPBF 304L ODS alloy before and after the thermal stability experiments revealed that despite the annihilation of dislocations, induced cellular substructure by the LPBF process was partially retained in the ODS alloy even after aging at 1200 °C. The size of Y-Si-O nanoparticles after aging at 1200 °C increased from 25 to 50 nm. EBSD analysis revealed that nanoparticles retained the microstructure of LPBF 304L ODS and hindered recrystallization and further grain growth. At 600 °C and 800 °C, the yield stress of the 290 and 145 MPa were measured, respectively, which are substantially higher than 113 MPa, and 68 MPa for 304L at the same temperatures. Furthermore, the creep properties of LPBF 304L ODS alloy were evaluated at a temperature of 700 °C under three applied stresses of 70, 85, and 100 MPa yielding a stress exponent (n) of ~7.7; the minimum creep rate at 100 MPa was found to be about two orders of magnitude lower than found in the literature for wrought 304L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Complete Optimization of LPBF Ni-Based Alloys Down-Selected from FY23 Candidate Materials Including, Thermodynamic Modeling, Sample Fabrication and Microstructure Characterization

The goal of the Advanced Materials and Manufacturing Technologies (AMMT) program is to accelerate the incorporation of new materials and manufacturing technologies into advanced nuclear-related systems. Although 316H stainless steel fabricated by laser powder bed fusion (LPBF) has already been identified as an alloy that could have a significant effect on various reactor technologies, many other materials and manufacturing techniques are being evaluated. Nickel-based alloys typically offer higher-temperature capabilities compared with advanced stainless steels, and previous reports looked at three Ni-based alloy categories: low-Co alloys with a potential use close to the reactor core; high-temperature, high-strength alloys; and molten salt–compatible alloys. In the first category, alloy 718 was studied in 2023, and creep testing at 600°C and 650°C revealed that the alloy exhibited great creep strength after the appropriate annealing but had low ductility. Advanced characterization was recently conducted to highlight the presence of strengthening γ' and γ" precipitates after creep testing and to show that brittle phases at grain boundaries might explain the low ductility of LPBF 718 compared with wrought 718. For the high-temperature, high-strength alloys, previously purchased powders of alloys 617, 230, and 625 were used to assess the printability of these three solution-strengthened alloys. Hot cracking could not be suppressed for alloy 617 and 230, and it was shown that these cracks, which were elongated along the build direction (BD), had a drastic effect on the ductility of alloy 230 at room temperature when specimens were machined perpendicular to the BD. On the contrary, LPBF printing of crack-free alloy 625 was achieved using similar printing parameters, and the alloy looked like a promising candidate for various reactor technologies. The fabrication of alloy 282 by LPBF, a γ'-strengthened alloy with great creep strength up to 800°C, was performed in 2023, and x-ray computed tomography (XCT) scans of the alloy before and after creep testing at 750°C were carried out to assess the effect of flaws on the alloy’s creep behavior. Correlation between the flaws’ volume fraction, creep ductility, and creep lifetime could be established, and future work on LPBF 625 will take full advantage of in situ printing data and ex situ XCT scans to accelerate the alloy qualification. Finally, single track experiments were performed on the two alloys previously identified as good molten salt–resistant, Ni-based candidates: Hastelloy N and 244. Various laser parameters were considered, and cracking was not observed for either of the two alloys. Wrought 244 offers better creep strength and molten salt compatibility than alloy 625, and future work will aim to establish the alloy LPBF processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Growth and structural transitions of core-shell nanorods in nanocrystalline Al-Ni-Y

Unique nanorod precipitates with a core-shell structure are found to nucleate from the grain boundaries of a bulk nanocrystalline Al-Ni-Y alloy fabricated via powder consolidation, contributing significantly to stabilization and strengthening. The local structure, chemistry, and evolution of these features during annealing are reported here. In the as-consolidated state, the nanorods can be either structurally ordered or disordered, yet a consistent chemical patterning is found where the core is primarily Al plus C while the shell is enriched with Y. As annealing time increases, more nanorods transform to an ordered structure as they coarsen while the core composition remains unchanged. In contrast, the shell chemistry transitions from Y-rich to Ni-rich with longer annealing treatments, most likely due to the different diffusivities of Y and Ni in Al. Furthermore, a spatial and chemical correlation between the nanorods and amorphous complexions is observed, suggesting that these complexions serve as preferential nucleation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A High-Speed Rotational Diamond Anvil Cell for In Situ Analysis of Hierarchical Microstructural Evolution of Metallic Alloys during Extreme Shear Deformation

High speed shear deformation is ubiquitous in engineering applications, ranging from material processing methods such as friction stir processing/extrusion and in tribological contacts. However, analyzing the microstructural evolution of materials while they are undergoing high speed shear deformation have been a long-standing challenge. This led to predominant reliance on ex situ microscopy before and after shear deformation. But ex situ microscopy lacks the ability to analyze dynamic and transient hierarchical microstructural evolution mechanisms that could occur during shear deformation of materials. Therefore, to better understand the dynamic mechanisms of mass and energy transfer in materials under shear deformation, we developed a first of its kind high-speed rotational diamond anvil cell (HS-RDAC) for synchrotron-based in situ high-energy x-ray diffraction (XRD). We studied the time resolved lattice strain evolution, XRD peak broadening and changes in spatial variation of shear deformation induced alloying in pure metal and metal alloy sheets and powder mixture using the HS-RDAC. These in situ results were combined with detailed ex situ microstructural characterization before and after the shear deformation using transmission electron microscopy and atom probe tomography, which revealed the different stages of evolution of a shear deformation induced hierarchical nanostructure. Multiscale computational simulations including computational fluid dynamics, crystal plasticity, molecular dynamic simulation and density functional theory uncovered the mechanisms behind morphological changes, evolution of defect structures and changes in driving force for shear deformation induced intermixing. In conclusion, this in situ HS-RDAC capability, in combination with ex situ microstructural characterization and computational simulations, can provide new insights into the hierarchical microstructural evolution pathway during shear deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Empirical Investigation of Properties for Additive Manufactured Aluminum Metal Matrix Composites

Laser additive manufacturing with mixed powders of aluminum alloy and silicon carbide (SiC) or boron carbide (B4C) is investigated in this experiment. With various mixing ratios of SiC/Al to form metal matrix composites (MMC), their mechanical and physical properties are empirically investigated. Parameters such as laser power, scan speed, scan pattern, and hatching space are optimized to obtain the highest density for each mixing ratio of SiC/Al. The mechanical and thermal properties are systematically investigated and compared with and without heat treatment. It shows that 2 wt% of SiC obtained the highest strength and Young’s modulus. Graded composite additive manufacturing (AM) of MMC is also fabricated and characterized. Various types of MMC devices, such as heat sink using graded SiC MMC and grid type three-dimensional (3D) neutron collimators using boron carbide (B4C), were also fabricated to demonstrate their feasibility for applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

AA2024/SiC metal matrix composites simultaneously improve ductility and cracking resistance during elevated temperature deformation

Here this study uses the stir-casting technique to combine a semi-solid AA2024 alloy directly with finely-sized β-SiC p embedded as a powder or with mechanically alloyed granules as a delivery agent. Liquid-state primary fabrication tends to form agglomerates of reinforcement particles, whereas rolling better distributes the composite constituents. Sub-micron reinforcements of low volume fractions do not significantly increase the hardness of the composite materials. Uniaxial tensile testing at elevated temperatures over a wide range of strain rates showed simultaneous increases in the ductility and crack resistance of AA2024 + SiC p granules embedded as a powder when compared to the non-reinforced control material at lower strain rates, with the same toughness as the control material. The maximum engineering strain of 252.7 ± 19.2% was observed in AA2024/SiCp at a strain rate of 10 -4 s -1 . This improvement in properties is attributed to grain refinement in the MMCs, leading to pinning events during the straining and ductility increases. The resultant impediments to grain growth and crack propagation allow the fine-sized reinforcements to control dynamic microstructural changes during fatigue. Cube {001}<100> is a dominant texture component in AA2024, whereas the Goss {011}<100> and S {123}<634> components mainly represent the texture of the discontinuously reinforced aluminum matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Processing Parameters on Recrystallization During Hot Isostatic Pressing of Stellite-6 Fabricated Using Laser Powder Bed Fusion Technique

Crack-free Stellite-6 alloy was fabricated using the laser powder bed fusion technique equipped with a heating module as the first attempt. Single tracks were printed with a build plate heated to 400 °C to identify the processing window. Based on the melt pool dimensions, two combinations (sample A: 300 W/750 mm/s and sample B: 275 W/1000 mm/s) were identified to print the cubes. The as-printed microstructure comprised FCC-Co dendrites with M7C3 in the interdendritic region. W-rich M6C particles were found in the overlapping regions between the melt pools, matching the Scheil simulations. However, gas pores were observed due to the higher nitrogen and oxygen content of the feedstock requiring hot isostatic pressing (HIP) at 1250 °C and 150 MPa for 2 h. Sample A was partially recrystallized with slightly coarsened M7C3, while sample B underwent complete recrystallization followed by grain growth along with higher coarsening of the M7C3 after HIP. The varying recrystallization behavior can be attributed to the difference in residual stresses and grain aspect ratio in the as-built condition dictated by laser power and scanning speed. The microhardness after HIP was slightly higher than its wrought counterpart, indicating no severe impact of post-processing on the properties of Stellite-6 alloy.

Sridar, Soumya (ORCID:0000000306775408)↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Magnetostrictive materials for enhanced sensors and electronic components

Magnetostriction is a property of magnetic materials that causes them to change their shape or dimensions proportional to their magnetization. Low-cost, mechanically robust magnetostrictive sensors would be valuable for a wide range of applications across the DOE and national security mission space, such as monitoring the internal conditions of pipelines, rapidly detecting high-impedance faults in power lines (e.g. trees touching power lines), or enhancing implantable systems for the human body. Dilute doping (<1 at.%) of rare earth elements (REE) has been shown to amplify the magnetostriction. Furthermore, alloy processing by rapid cooling from high temperature tends to result in texturing and therefore greater magnetostriction values, which bodes well for developing advanced manufacturing approaches significantly less expensive than single crystal growth. The goal of this effort was to develop robust, low-cost magnetostrictive materials compatible with advanced manufacturing techniques to exploit the rapid cooling of these approaches while retaining the ability to produce fully dense structures. To be useful as a sensor or actuator the coercivity of the material needs to be minimized so that there is minimal magnetic hysteresis. Employing a small scale laser powder bed fusion (L-PBF) system, specimens of Fe-Ga-Ce were built from alloy powder which had a magnetostriction of 289 ppm along the build direction and 197 ppm perpendicular to the build direction. These values are not far from the 310-350 ppm observed in single crystals of Fe-Ga. The results of the series of samples run suggest this is a very promising route for REE doping to higher levels, especially if the powders can be produced using far from equilibrium approaches such as ultrasonic atomization. The promising results from applying additive manufacturing techniques to these materials, particularly the inexpensive Fe-Al system, has potential for inexpensive high-performing magnetostrictive parts producible at large scales for low-cost sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Which way does the dendrite grow? Competition among epitaxy, preferred growth direction, and thermal gradients in powder bed fusion additive manufacturing

The as-processed microstructure of metal alloy parts manufactured through laser powder bed fusion (LPBF) is heavily derived from the cellular dendritic solidification. The growth direction of dendrites within the melt pool is determined through competition among epitaxial growth, preferred growth directions, and maximum thermal gradients. However, the dominant factor and the specific role of each in developing melt pool microstructures remain unknown. Here, in this study, we performed single laser track scans on an SS316L single crystal substrate and combined experimental characterization of microstructure and crystal orientations with Computational Fluid Dynamics simulations of thermal gradients to evaluate the role of each factor in determining dendritic growth direction and evolution. Our results reveal that epitaxial growth dominates microstructure development by preferentially growing along a single 〈100〉 variant of the single crystal substrate adjacent to the melt pool boundary. Under LPBF’s highly curved and rapidly evolving thermal field, this preferential dendrite variant selection and its continued growth from the melt pool boundary to the centerline are governed by the local temperature gradient magnitude at the solid-liquid interface, rather than by the instantaneous maximum temperature gradient direction alone. Using these findings, we successfully predict changes in the dendrite growth direction with changing laser scan direction on a single crystal substrate, and show that the geometric melt pool centerline can deviate from the microstructural centerline because asymmetric local temperature gradient magnitudes transiently limit growth, resulting in different dendrite travel distances on each side of the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure Optimization and Novel Processing Development of ODS Steels for Fusion Environments (Final ARPA-E Report)

This project aimed to develop scalable, cost-effective fabrication of high-performance, oxide- dispersion-strengthened (ODS) steel using advanced manufacturing methods (AMMs) for fusion blanket-breeding applications. Gas atomization reaction synthesis (GARS) enables the synthesis of precursor ODS steel powders without prolonged mechanical alloying. This process creates a chromium (Cr)-enriched surface oxide with yttrium/titanium (Y/Ti)-enriched intermetallics in powder interiors. GARS powders were consolidated to >99% of the theoretical density using a first-of-a-kind shear assisted processing and extrusion (ShAPE) and laser-based powder bed fusion (L-PBF) AM processes. These processes led to ODS steels containing a high-density of nano-oxide dispersoids that enhance high-temperature mechanical properties. Such scalable, cost-effective fabrication of ODS steels can enable efficient power conversion cycles (=40%) at operating temperatures beyond 900 K in future fusion power plants.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydrogen Permeation in FeCrAl APMT Alloy for Accident Tolerant Fuel Cladding

Iron-chromium-aluminum (FeCrAl) alloys such as APMT (advanced powder metallurgy tubing) are candidate materials to replace zirconium alloys for the light water reactor fuel cladding. This alloy meets the requirements to be a material more tolerant of high-temperature accidents than the current zirconium alloys. One concern is that the use of FeCrAl may result in an increase in tritium presence in the coolant compared to the current design. The aim of the current research was to obtain effective diffusion coefficients (D eff ) for hydrogen through APMT using the Devanathan-Stachurski cell. Results showed that at 30°C the D eff value was 2.8 × 10 -8 cm 2 /s. Results also showed a linear relationship between the permeated hydrogen flux and the inverse of the test specimen thickness, which demonstrated the validity of the permeation measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗
DOE OSTI2024

Ultrahigh Performance Metallic Turbine Blades for Extreme Environments

In ULTIMATE Phase-I, The Boeing Company and Alloyed Inc. aimed to produce ultrahigh performance metallic extreme environment turbine blades with a base blade alloy capable of inert operation at 1300C, and a maximum coated blade operating temperature up to 1800C. High-performance structural designs for extreme service conditions place additional demands on the present material capability and can potentially outpace the current state-of-the-art in the alloy design space and metal processing. As a part of exploration and adoption of novel concepts for material maturation, the team explored a series of capable base novel refractory complex concentrated alloy (RCCA) compositions and potential powder enhancements. Advanced manufacturing processes, with a focus on laser powder bed fusion additive manufacturing (AM) and powder metallurgy (PM) approaches, were applied to consolidate new alloys and for near net shape processing of blades from the base RCCA.

Yousefiani, Ali↗