Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ceramic Capacitor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Synthesis of ZrO{sub 2} nanoparticles by hydrothermal treatment

Zirconium oxide (zirconia, ZrO{sub 2}) is the most common material used for electrolyte of solid oxide fuel cells (SOFCs). Zirconia has attracted attention for applications in optical coatings, buffer layers for growing superconductors, thermal-shield, corrosion resistant coatings, ionic conductors, and oxygen sensors, and for potential applications including transparent optical devices and electrochemical capacitor electrodes, fuel cells, catalysts, and advanced ceramics. In this work, zirconia particles were synthesized from ZrCl{sub 4} precursor with hydrothermal treatment in a batch reactor. Hydrothermal treatment may allow obtaining nanoparticles and sintered materials with controlled chemical and structural characteristics. Hydrothermal treatment was carried out at temperatures of 150 – 200°C with precursor concentration of 0.1 – 0.5 M. Zirconia particles obtained from this treatment were analyzed by using SEM, PSD and XRD to characterize the morphology, particle size distribution, and crystallinity, respectively. Based on the analysis, the size of zirconia particles were around 200 nm and it became smaller with decreasing precursor concentration. The increasing temperature caused the particles formed having uniform size. Zirconia particles formed by hydrothermal treatment were monoclinic, tetragonal and cubic crystal.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct-write, chemically-prepared temperature insensitive dielectrics.

Development of high energy density dielectrics with low temperature coefficients of capacitance that are systems integrable are needed for extreme environment, defense and automotive applications. The synthesis of high purity chemically prepared Ca(Zr,Ti)O3 powders is described and has resulted in the lowering of conventional firing temperatures by over 100 C. Direct write aerosol spray deposition techniques have been used to fabricate high quality single layer and multilayer capacitors from these powders. The dielectric constants of the direct write capacitors are equivalent to those of fired bulk ceramics. Our presentation emphasizes the synthesis, phase evolution and microstructure development that has resulted in dielectrics with energy densities in excess of 3 J/cm3 with less than 1% change in dielectric constant over a 200 C temperature range.

36 MATERIALS SCIENCE↗

Plasmoid Thruster for High Specific-Impulse Propulsion

A report discusses a new multi-turn, multi-lead design for the first generation PT-1 (Plasmoid Thruster) that produces thrust by expelling plasmas with embedded magnetic fields (plasmoids) at high velocities. This thruster is completely electrodeless, capable of using in-situ resources, and offers efficiencies as high as 70 percent at a specific impulse, I(sub sp), of up to 8,000 s. This unit consists of drive and bias coils wound around a ceramic form, and the capacitor bank and switches are an integral part of the assembly. Multiple thrusters may be gauged to inductively recapture unused energy to boost efficiency and to increase the repetition rate, which, in turn increases the average thrust of the system. The thruster assembly can use storable propellants such as H2O, ammonia, and NO, among others. Any available propellant gases can be used to produce an I(sub sp) in the range of 2,000 to 8,000 s with a single-stage thruster. These capabilities will allow the transport of greater payloads to outer planets, especially in the case of an I(sub sp) greater than 6,000 s.

Fimognari, Peter↗

Rocket Propulsion 21 Steering Committee Meeting (RP21) NASA In-Space Propulsion Update

In-house Support of NEXT-C Contract Status Thruster NEXT Long Duration Test post-test destructive evaluation in progress Findings will be used to verify service life models identify potential design improvements Cathode heater fabrication initiated for cyclic life testing Thruster operating algorithm definition verification initiated to provide operating procedures for mission users High voltage propellant isolator life test voluntarily terminated after successfully operating 51,200 h Power processor unit (PPU) Replaced all problematic stacked multilayer ceramic dual inline pin capacitors within PPU Test bed Rebuilt installed discharge power supply primary power board Completed full functional performance characterization Final test report in progress Transferred PPU Testbed to contractor to support prototype design effort.

Electric Propulsion↗

Nondestructive Detection of Cracks in Ceramics Using Vicinal Illumination

Cracks and other defects in ceramic materials can be difficult or impossible to examine and photograph due to the extreme lack of contrast. A method for inspecting translucent ceramics using scattered light, also known as vicinal illumination, will be described. This method has been known in the ceramics industry for quite some time, but is not well known in the testing and failure analysis community. Electronics applications include substrates, packages, multilayer capacitors, and thin film resistors. Ceramic materials are used in electronic applications as microcircuit packages and substrates which carry signals and power between microcircuits. Fine cracks in ceramic materials can result in mechanical failures, electrical failures, and loss of hermeticity. Often, fine cracks are difficult or impossible to detect using standard nondestructive inspection techniques such as visual inspection, ultrasonic inspection, or vapor crack detection. Dye penetrant inspection is usually effective, but contaminates the part, which is unacceptable for space flight hardware. One effective nondestructive inspection method of detecting cracks involves examining the way in which light scatters through the ceramic material when viewed with a standard bright field reflected light microscope. This method, termed vicinal illumination, has been used for detecting cracks during failure analyses of several part types, and screening of space flight hardware. The technique has proven effective on several different types of ceramic materials as well. A related method for use with dark field equipment has also been used to successfully locate otherwise invisible cracks.

Hull, Scott M.↗

Using Defects to Create Ceramics with Giant Permittivity as Ultracapacitors

Dielectrics with a high and weakly- temperature-dependent permittivity are highly desirable for the development of high performance energy storage devices. It is well known that ferroelectrics (FEs) exhibit a high permittivity that is strongly dependent on the temperature due to phase transition. In this project, the FE BaTiO3 (BTO), based ceramics are developed as ultra-capacitors by introducing defects to eliminate the phase transition and enhance the permittivity. The ceramics are fabricated using a unique process: BTO nanoparticles are coated with a nano-layer of SiO2 and, then, sintered in vacuum using SPS process. The ceramics exhibit a giant permittivity and many other unique properties.

Talebinezhad, H.↗

275 C Downhole Switched-Mode Power Supply

A vee-square (V2) control based controller IC is developed for a switch mode power supply capable of operating at extreme temperature/harsh environment conditions. A buck type regulator with silicon carbide power junction field effect transistors (JFET) as power devices is used to analyze the performance of controller. Special emphases are made on the analog sub-blocks--voltage reference, operational transconductance amplifier and comparator as individual building blocks. Transformer coupled gate drives and high temperature operable magnetic cores and capacitors are identified and tested for use in the design. Conventional ceramic chip packaging of ICs combined with lead carrier type mounting of passive filter components is introduced for hybrid packaging of the complete product. The developed SMPS is anticipated to support the operation of down-hole microcontrollers and other electronics devices that require low/medium power filtered dc inputs over an operating temperature of 275 C.

42 ENGINEERING↗

2010 Ceramics, Solid State Studies in Gordon Research Conference

The 2010 Gordon Conference on Solid State Studies in Ceramics will present forefront research on ceramic materials in energy conversion, storage, and environmental sustainability. Oxide materials in advanced Li-ion batteries will be featured, including first principles computational methods, new experimental methods, novel synthesis, and the design of batteries that exploit nanoscale cathode materials. Several speakers address advances in oxides for solar applications, including photo-catalysts for solar hydrogen production and dye sensitized solar cells, along with thin film photovoltaics. Fast ionic conducting ceramics in electrochemical energy conversion and storage will be addressed for fuel cells and electrochemical storage. New concepts for electrochemical capacitor materials will be addressed, as will thermoelectric, geopolymers, and ceramics in nuclear energy. The Conference will bring together investigators at the forefront of their field as well as junior scientists in a collegial atmosphere, with programmed discussion sessions and informal gatherings in the afternoons and evenings. Poster presentations provide opportunities for junior scientists and graduate students to present their work and exchange ideas with leaders in the field. This Conference provides an avenue for scientists from different disciplines to explore new ideas and promotes cross-disciplinary collaborations in the various research areas represented.

08 HYDROGEN↗

Giant energy-storage density with ultrahigh efficiency in lead-free relaxors via high-entropy design

Next-generation advanced high/pulsed power capacitors rely heavily on dielectric ceramics with high energy storage performance. However, thus far, the huge challenge of realizing ultrahigh recoverable energy storage density (W rec ) accompanied by ultrahigh efficiency (η) still existed and has become a key bottleneck restricting the development of dielectric materials in cutting-edge energy storage applications. Here, we propose a high-entropy strategy to design “local polymorphic distortion” including rhombohedral-orthorhombic-tetragonal-cubic multiphase nanoclusters and random oxygen octahedral tilt, resulting in ultrasmall polar nanoregions, an enhanced breakdown electric field, and delayed polarization saturation. A giant W rec ~10.06 Jcm –3 is realized in lead-free relaxor ferroelectrics, especially with an ultrahigh η ~90.8%, showing breakthrough progress in the comprehensive energy storage performance for lead-free bulk ceramics. This work opens up an effective avenue to design dielectric materials with ultrahigh comprehensive energy storage performance to meet the demanding requirements of advanced energy storage applications.

25 ENERGY STORAGE↗

Automatically Inspecting Thin Ceramics For Pinholes

Proposed apparatus for inspecting prefired ceramic materials detects minute flaws that might escape ordinary visual inspections. Method detects flaws and marks locations. Intended for such thin ceramic parts as insulation in capacitors and some radio-frequency filters.

Honaker, James R.↗

A high energy density relaxor antiferroelectric pulsed capacitor dielectric

Pulsed capacitors require high energy density and low loss, properties that can be realized through selection of composition. Ceramic (Pb{sub 0.88}La{sub 0.08})(Zr{sub 0.91}Ti{sub 0.09})O{sub 3} was found to be an ideal candidate. La{sup 3+} doping and excess PbO were used to produce relaxor antiferroelectric behavior with slim and slanted hysteresis loops to reduce the dielectric hysteresis loss, to increase the dielectric strength, and to increase the discharge energy density. The discharge energy density of this composition was found to be 3.04 J/cm{sup 3} with applied electric field of 170 kV/cm, and the energy efficiency, defined as the ratio of the discharge energy density to the charging energy density, was 0.920. This high efficiency reduces the heat generated under cyclic loading and improves the reliability. The properties were observed to degrade some with temperature increase above 80 °C. Repeated electric field cycles up to 10 000 cycles were applied to the specimen with no observed performance degradation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fabrication of PVDF-TrFE based bilayered PbTiO{sub 3}/PVDF-TrFE films capacitor

Development of high performance capacitor is reaching towards new generation where the ferroelectric materials take places as the active dielectric layer. The motivation of this study is to produce high capacitance device with long life cycle. This was configured by preparing bilayered films where lead titanate as an active dielectric layer and stacked with the top dielectric layer, poly(vinyledenefluoride-trifluoroethylene). Both of them are being referred that have one in common which is ferroelectric behavior. Therefore the combination of ceramic and polymer ferroelectric material could perform optimum dielectric characteristic for capacitor applications. The fabrication was done by simple sol-gel spin coating method that being varied at spinning speed property for polymer layers, whereas maintaining the ceramic layer. The characterization of PVDF-TrFE/PbTiO3 was performed according to metal-insulator-metal stacked capacitor measurement which includes structural, dielectric, and ferroelectric measurement.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis and microstructural TEM investigation of CaCu{sub 3}Ru{sub 4}O{sub 12} ceramic and thin film

CaCu{sub 3}Ru{sub 4}O{sub 12} (CCRO) is a conductive oxide having the same structure as CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) and close lattice parameters. The later compound is strongly considered for high density parallel plates capacitors application due to its so-called colossal dielectric constant. The need for an electrode inducing CCTO epitaxial growth with a clean and sharp interface is therefore necessary, and CCRO is a good potential candidate. In this paper, the synthesis of monophasic CCRO ceramic is reported, as well as pulsed laser deposition of CCRO thin film onto (001) NdCaAlO{sub 4} substrate. Structural and physical properties of bulk CCRO were studied by transmission electron microscopy and electron spin resonance. CCRO films and ceramic exhibited a metallic behavior down to low temperature. CCRO films were (001) oriented and promoted a CCTO film growth with the same orientation. - Graphical Abstract: Structure of CaCu{sub 3}Ru{sub 4}O{sub 12} showing the RuO{sub 6} octahedra and the square planar environment for Cu{sup 2+}. Highlights: > In this study, we investigate the structural properties and microstructure of ceramics CaCu{sub 3}Ru{sub 4}O{sub 12}. > We study the conduction properties of polycrystalline material. > Then we synthesize the conductive thin film which is deposited on a high K material with the same structure (CaCu{sub 3}Ti{sub 4}O{sub 12}).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dielectric and electrical studies of Pr{sup 3+} doped nano CaSiO{sub 3} perovskite ceramics

Highlights: • CaSiO{sub 3}:Pr{sup 3+} was prepared by facile low temperature solution combustion method. • The crystalline phase of the product is obtained by adopting sintering method. • Samples prepared at 500 °C and calcined at 900 °C for 3 h showed β-phase. • The Pr{sup 3+} doped CaSiO{sub 3} shows “unusual results”. • The electrical microstructure has been accepted to be of internal barrier layer capacitor. - Abstract: CaSiO{sub 3} nano-ceramic powder doped with Pr{sup 3+} has been prepared by solution combustion method. The powder Ca{sub 0.95}Pr{sub 0.05}SiO{sub 3} is investigated for its dielectric and electrical properties at room temperature to study the effect of doping. The sample is characterized by X-ray diffraction and infrared spectroscopy. The size of either of volume elements of CaSiO{sub 3}:Pr{sup 3+} estimated from transmission electron microscopy is about 180–200 nm. The sample shows colossal dielectric response at room temperature. This colossal dielectric behaviour follows Debye-type relaxation and can be explained by Maxwell–Wagner (MW) polarization. However, analysis of impedance and electric modulus data using Cole–Cole plot shows that it deviates from ideal Debye behaviour resulting from the distribution of relaxation times. The distribution in the relaxation times may be attributed to existence of electrically heterogeneous grains, insulating grain boundary, and electrode contact regions. Doping, thus, results in substantial modifications in the dielectric and electrical properties of the nano-ceramic CaSiO{sub 3}.

36 MATERIALS SCIENCE↗

Development of a coolant channel helium and nitrogen gas ratio sensor for a high temperature gas reactor

To measure the changing gas composition of the coolant during a postulated High Temperature Gas Reactor (HTGR) accident, an instrument is needed. This instrument must be compact enough to measure the ratio of the coolant versus the break gas in an individual coolant channel. This instrument must minimally impact the fluid flow and provide for non-direct signal routing to allow minimal disturbance to adjacent channels. The instrument must have a flexible geometry to allow for the measurement of larger volumes such as in the upper or lower plenum of a HTGR. The instrument must be capable of accurately functioning through the full operating temperature and pressure of a HTGR. This instrument is not commercially available, but a literature survey has shown that building off of the present work on Capacitance Sensors and Cross-Capacitors will provide a basis for the development of the desired instrument. One difficulty in developing and instrument to operate at HTGR temperatures is acquiring an electrical conductor that will not melt at 1600 deg. C. This requirement limits the material selection to high temperature ceramics, graphite, and exotic metals. An additional concern for the instrument is properly accounting for the thermal expansion of both the sensing components and the gas being measured. This work covers the basic instrument overview with a thorough discussion of the associated uncertainty in making these measurements. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High thermal stability and excellent dielectric properties of a novel X8R-type CdCu3Ti4O12 ceramics through a sol-gel technique

Highlights: • CdCu{sub 3}Ti{sub 4}O{sub 12} (CdCTO) ceramics were successfully synthesized via the sol-gel method, and the optimized processing parameters were obtained. • The outstanding dielectric properties: ε{sub r} ≈ 1.63 × 10{sup 4} and tan δ = 0.035 (at 10 kHz) could be obtained in CdCTO ceramics sintered at 1000 °C. • The CdCTO-SG ceramics obtained an excellent thermal stability. - Abstract: CdCu{sub 3}Ti{sub 4}O{sub 12} (CdCTO) ceramics were systematically synthesized via the sol-gel technique. The optimal CH{sub 3}COOH and Ti(OC{sub 4}H{sub 9}){sub 4} concentrations in the synthesis solution and processing temperature were found to be 5.0 vol%, 0.50 mol/L and 60 °C, respectively. These materials exhibited high densities and fine-grained microstructures along with outstanding dielectric properties, including an ε{sub r} of approximately 1.63 × 10{sup 4} and a tan δ of 0.035 at 10 kHz. Over the temperature range from −55 to 150 °C, the temperature coefficients of the dielectric constant at 1 and 10 kHz were −13.9% to 1.20% and −9.10% to 3.92%, respectively, indicating that these ceramics possess excellent thermal stability. These properties also meet the requirements for X8R applications. Data acquired from complex impedance spectroscopy and electrical modulus assessments demonstrates that the superior dielectric properties of these CdCTO ceramics can be attributed to the internal barrier layer capacitor theory (IBLC).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Additive manufacturing of ceramic materials for energy applications: Road map and opportunities

Among engineering materials, ceramics are indispensable in energy applications such as batteries, capacitors, solar cells, smart glass, fuel cells and electrolyzers, nuclear power plants, thermoelectrics, thermoionics, carbon capture and storage, control of harmful emission from combustion engines, piezoelectrics, turbines and heat exchangers, among others. Advances in additive manufacturing (AM) offer new opportunities to fabricate these devices in geometries unachievable previously and may provide higher efficiencies and performance, all at lower costs. This article reviews the state of the art in ceramic materials for various energy applications. The focus of the review is on material selections, processing, and opportunities for AM technologies in energy related ceramic materials manufacturing. The aim of the article is to provide a roadmap for stakeholders such as industry, academia and funding agencies on research and development in additive manufacturing of ceramic materials toward more efficient, cost-effective, and reliable energy systems.

36 MATERIALS SCIENCE↗

Origin of colossal dielectric permittivity of rutile Ti 0.9 In 0.05 Nb 0.05 O 2 : single crystal and polycrystalline

Here in this article, we investigated the dielectric properties of (In + Nb) co-doped rutile TiO 2 single crystal and polycrystalline ceramics. Both of them showed colossal, up to 10 4 , dielectric permittivity at room temperature. The single crystal sample showed one dielectric relaxation process with a large dielectric loss. The voltage-dependence of dielectric permittivity and the impedance spectrum suggest that the high dielectric permittivity of single crystal originated from the surface barrier layer capacitor (SBLC). The impedance spectroscopy at different temperature confirmed that the (In+Nb) co-doped rutile TiO 2 polycrystalline ceramic had semiconductor grains and insulating grain boundaries, and that the activation energies were calculated to be 0.052 eV and 0.35 eV for grain and grain boundary, respectively. The dielectric behavior and impedance spectrum of the polycrystalline ceramic sample indicated that the internal barrier layer capacitor (IBLC) mode made a major contribution to the high ceramic dielectric permittivity, instead of the electron-pinned defect-dipoles.

36 MATERIALS SCIENCE↗