SEARCH · Search NASA

Results for “Cladding design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Experimental Operation of a Prototype 750C Advanced Chloride Molten Salt Bellows Valve

To achieve DOE 2030 SunShot targets that reduce the cost of liquid-based solar by an additional 40% to 70% beyond 2018 costs, a more reliable, highly manufacturable flow valve, capable of achieving operational temperatures of >700°C is required [1]. This paper investigates the development of an innovative high-temperature chloride molten salt valve, with operation up to 750°C. This valve is intended to be employed within Gen 3 CSP liquid-based thermal energy storage (TES) systems as well as Gen 4 modular salt reactor (MSR) technologies. This work details the general design and flow testing of a bellows-seal flow control valve (FCV). This design includes an integrated closed-loop thermal control system to ensure robust design for freeze-thaw cycles. The self-contained thermal management STM system, is unique in the salt valve industry since it is an integrated solution to provide a consistent, repeatable alternative to typical heat tracing. Additionally, the design includes the employment of a novel heat pipe valve stem to facilitate enhanced passive thermal management into the valve assembly. This valve stem heat pipe is designed to facilitate natural circulation within the bonnet to ensure robust operation, during both nominal and transient thermal operation. The valve body and trim will be designed using SS316H, consistent with Flowserve Corporation’s existing product base and is code qualified but will utilize clad material for materials corrosion, manufacturing cost reduction and compatibility to ensure design flexibility. A test campaign was performed in this investigation utilizing a novel 750°C ternary chloride (20%NaCl/40%MgCl2/40%KCl by mol. wt. %) molten salt flow loop. A discussion about the design and installation of the valves within this test bed is provided for this investigation. Valve test results from this study assessed Cv curves as well as multiple actuator cycles, under varying thermodynamic and operational mode conditions, which would be characteristic within a commercial molten salt facility. The results indicate nominal operation for the baseline design, though improved performance and reliability is expected with the full designed FCV.

Armijo, Kenneth (ORCID:0000000346832147)↗

DOE OSTI2016

Determination of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

An in-reactor experiment is being designed in order to validate the pellet-cladding mechanical interaction (PCMI) behavior of the BISON fuel performance code. The experimental parameters for the test rod being placed in the Halden Research Reactor are being determined using BISON simulations. The 3D model includes a missing pellet surface (MPS) defect to generate large local cladding deformations, which should be measureable after typical burnup times. The BISON fuel performance code is being developed at Idaho National Laboratory (INL) and is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. BISON supports both 2D and 3D finite elements and solves the fully coupled equations for solid mechanics, heat conduction and species diffusion. A number of fuel performance effects are included using models for swelling, densification, creep, relocation and fission gas production & release. In addition, the mechanical and thermal contact between the fuel and cladding is explicitly modelled using a master-slave based contact algorithm. In order to accurately predict PCMI effects, the BISON code includes the relevant physics involved and provides a scalable and robust solution procedure. The depth of the proposed MPS defect is being varied in the BISON model to establish an optimum value for the experiment. The experiment will be interrupted approximately every 6 months to measure cladding radial deformation and provide data to validate BISON. The complete rodlet (~20 discrete pellets) is being simulated using a 180° half symmetry 3D model with MPS defects at two axial locations. In addition, annular pellets will be used at the top and bottom of the pellet stack to allow thermocouples within the rod to measure the fuel centerline temperature. Simulation results will be presented to illustrate the expected PCMI behavior and support the chosen experimental design parameters.

BISON↗

DOE OSTI2016

Analysis of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

BISON↗

DOE OSTI2018

Study on neutronics calculation method of SCWR with annular fuel assembly - 26804

Many Supercritical Water Reactor designs have been proposed all over the world. Annular fuel was employed in SCWR by Xi'an JiaoTong University to achieve lower fuel center temperature and lower cladding surface temperature. Different analysis codes have been developed for these designs. In this article, a neutronics calculation code for SCWR with annular fuel is developed. This code is compared with Monte-Carlo code doing both assembly and core calculation. The results showed that the spectra difference of PWRs and SCWRs is the main reason for assembly calculation errors and conventional assembly homogenization method is not suitable for SCWRs. Thus the group-collapsing and spatial-averaging method were studied to improve the accuracy. The few-group structure which contains 14 energy groups is used. The 'super-assembly' model is employed to consider effect of reflector. The results showed that the accuracy of effective multiplication factor and radial power was improved. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Multi-principal element alloys for fast reactor cladding applications

Given the extensive list of multi-principal element alloys (MPEAs) within literature and the overwhelming number of alloys that can be made from only a handful of elements, this article proposes a methodology for prioritizing alloys for use as cladding within advanced reactors. This paper applies neutronic, mechanical, and chemical assessments to a collection of MPEAs available within literature for use as advanced reactor cladding. The results are compared to a reference design of HT9, a ferritic/martensitic steel, for employed in sodium-cooled fast reactor. Mechanical assessments determined pressure limits for a thin-walled tube pressure boundary, thus relating the material's mechanical properties to a minimum acceptable wall thickness. Neutronic analyses reveal a maximum allowable wall thickness that a given material must meet to provide a level of neutronic economy that is equivalent to than that of HT9. Lastly, each alloying element is compared to typical fission products found in a fast reactor fuels to mitigate deleterious phenomena such as fuel-cladding chemical interactions (FCCI). These analyses indicate that Mo-Nb-Ti-V-based alloys are likely to be advantageous and that the inclusion of elements with a high neutronic penalty (e.g., Hf) could be considered with minimal consequences.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2017

Experimental design and analysis for irradiation of SiC/SiC composite tubes under a prototypic high heat flux

The purpose of this work is to design an irradiation vehicle for testing silicon carbide (SiC) fiber-reinforced SiC matrix composite cladding materials under conditions representative of a light water reactor in order to validate thermo-mechanical models of stress states in these materials due to irradiation swelling and differential thermal expansion. The design allows for a constant tube outer surface temperature in the range of 300–350 °C under a representative high heat flux (~0.66 MW/m 2 ) during one cycle of irradiation in an un-instrumented “rabbit” capsule in the High Flux Isotope Reactor. An engineered aluminum foil was developed to absorb the expansion of the cladding tubes, due to irradiation swelling, without changing the thermal resistance of the gap between the cladding and irradiation capsule. Finite-element analyses of the capsule were performed, and the models used to calculate thermal contact resistance were validated by out-of-pile testing and post-irradiation examination of the foils and passive SiC thermometry. Six irradiated cladding tubes (both monoliths and composites) were irradiated and subsequently disassembled in a hot cell. The calculated temperatures of passive SiC thermometry inside the capsules showed good agreement with temperatures measured post-irradiation, with two calculated temperatures falling within 10 °C of experimental measurements. Furthermore, the success of this design could lead to new opportunities for irradiation applications with materials that suffer from irradiation swelling, creep, or other dimensional changes that can affect the specimen temperature during irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

AFC FY 2023 HFIR Irradiation Test Matrix – Supported by the Design of a Ring Specimen Irradiation Vehicle

The development and deployment of accident-tolerant cladding materials in light water nuclear reactors requires the collection of neutron-irradiated properties of these materials with specific consideration to the material properties orientation (i.e., tube geometry). To that end, a test plan to irradiate several cladding tube and ring specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) was proposed, along with the development of a new capsule design that features ring specimens with a preexisting gauge section. This ring specimen geometry removes the need to machine a gauge section on the irradiated specimen and thus allows for direct application of a ring-pull test post-irradiation. The test matrix includes uncoated and chromium-coated Zircaloy-4 and advanced zirconium alloy cladding specimens, pre-characterized at ORNL. Plans are to irradiate the specimens at about 4 and 10 dpa—corresponding to two and five cycles at the HFIR centerline—with a target specimen gauge section temperature of 330°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2016

Thermal-Hydraulic Performance of the TREAT Multi-SERTTA for Reactivity Initiated Accident Experiments

Experimental testing in the Multi-Static Environment Rodlet Transient Test Apparatus (SERTTA) will lead the rebirth of transient fuel testing in the United States as part of the Accident Tolerant Fuels (ATF) progam. The Multi-SERTTA is comprised of four isolated pressurized environments capable of a wide variety of working fluids and thermal conditions. Ultimately, the TREAT reactor as well as the Multi-SERTTA test vehicle serve the purpose of providing desired thermal-hydraulic boundary conditions to the test specimen. The initial ATF testing in TREAT will focus on reactivity insertion accident (RIA) events using both gas and water environments including typical PWR operating pressures and temperatures. For the water test environment, a test configuration is envisioned using the expansion tank as part of the gas-filled expansion volume seen by the test to provide additional pressure relief. The heat transfer conditions during the high energy power pulses of RIA events remains a subject of large uncertainty and great importance for fuel performance predictions. To support transient experiments, the Multi-SERTTA vehicle has been modeled using RELAP5 with a baseline test specimen composed of UO2 fuel in zircaloy cladding. The modeling results show the influence of the designs of the specimen, vehicle, and transient power pulses. The primary purpose of this work is to provide input and boundary conditions to fuel performance code BISON. Therefore, studies of parameters having influence on specimen performance during RIA transients are presented including cladding oxidation, power pulse magnitude and width, cladding-to-coolant heat fluxes, fuel-to-cladding gap, transient boiling effects (modified CHF values), etc. The results show the great flexibility and capacity of the TREAT Multi-SERTTA test vehicle to provide testing under a wide range of prototypic thermal-hydraulic conditions as never done before.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

A robust alloy design (RAD) strategy for next-generation (IV) nuclear fission reactors

Next-generation nuclear reactors demand structural materials capable of withstanding extreme conditions, including high temperatures, intense neutron flux, and corrosive environments. Multi-Principal Element Alloys (MPEAs) have emerged as promising candidates due to their exceptional radiation tolerance, thermal stability, and compositional flexibility. This study introduces a versatile and customizable Robust Alloy Design (RAD) strategy for systematically designing MPEAs for GEN-IV reactor fuel cladding. The RAD framework integrates nuclear-relevant selection criteria, empirical parameter assessments, and high-throughput CALPHAD simulations to efficiently narrow compositional space and identify stable alloys. A unified RAD score developed for the first time, combines key performance metrics, including fuel-clad chemical interaction (FCCI), neutron absorption cross-section (NAC), valence electron configuration (VEC), and melting point factor (MPF), into a flexible ranking system adaptable to reactor-specific priorities. Among 724 candidates, V555(5Al–5Cr–5Fe–85V) emerged as the top alloy, validated experimentally with a homogeneous single-phase BCC microstructure and superior mechanical properties (nano-indentation: 3.389 ± 0.258 GPa; Vickers hardness: 240 ± 6.7 HV), significantly outperforming Zircaloy-4 and V-4Cr-4Ti. Importantly, the RAD strategy is not limited to nuclear applications; its customizable weighting system enables scalability to other extreme environments. This adaptability positions RAD strategy as a versatile tool for advanced materials design across multiple industries.

Alloy design↗

DOE OSTI2015

Status update of the BWR cask simulator

The performance of commercial nuclear spent fuel dry storage casks are typically evaluated through detailed numerical analysis of the system's thermal performance. These modeling efforts are performed by the vendor to demonstrate the performance and regulatory compliance and are independently verified by the Nuclear Regulatory Commission (NRC). Carefully measured data sets generated from testing of full sized casks or smaller cask analogs are widely recognized as vital for validating these models. Numerous studies have been previously conducted. Recent advances in dry storage cask designs have moved the storage location from above ground to below ground and significantly increased the maximum thermal load allowed in a cask in part by increasing the canister helium pressure. Previous cask performance validation testing did not capture these parameters. The purpose of the investigation described in this report is to produce a data set that can be used to test the validity of the assumptions associated with the calculations presently used to determine steady-state cladding temperatures in modern dry casks. These modern cask designs utilize elevated helium pressure in the sealed canister or are intended for subsurface storage. The BWR cask simulator (BCS) has been designed in detail for both the above ground and below ground venting configurations. The pressure vessel representing the canister has been designed, fabricated, and pressure tested for a maximum allowable pressure (MAWP) rating of 24 bar at 400 C. An existing electrically heated but otherwise prototypic BWR Incoloy-clad test assembly is being deployed inside of a representative storage basket and cylindrical pressure vessel that represents the canister. The symmetric single assembly geometry with well-controlled boundary conditions simplifies interpretation of results. Various configurations of outer concentric ducting will be used to mimic conditions for above and below ground storage configurations of vertical, dry cask systems with canisters. Radial and axial temperature profiles will be measured for a wide range of decay power and helium cask pressures. Of particular interest is the evaluation of the effect of increased helium pressure on heat load and the effect of simulated wind on a simplified below ground vent configuration.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Mechanical response and microstructure evolution from multiaxial stress relaxation in textured zircaloy nuclear cladding

Modern energy markets provide motivation for nuclear reactors to increase operational flexibility and load following capacity of existing reactor designs. The operational power changes result in fuel pellet expansion and contraction resulting in pellet-cladding mechanical interaction (PCMI) and high cladding stresses that are strongly related to stressed corrosion cracking (SCC) which can lead to fuel rod failure. This work aims to quantify the stress fields in cladding with a focus on multiaxial stress relaxation response from an imposed strain and the resulting microstructure changes in textured zircaloy claddings. Stress relaxation tests resulting in multiaxial stress fields are performed to measure the material response of Zircaloy-4 nuclear cladding. Multiple experiments using samples from the same piece of cladding are performed so samples with the same processing history may be removed at strategic points throughout mechanical testing for microstructure characterization. The microstructure evolution is analyzed with mechanical response to evaluate the static recovery impact on crystallographic texture and grain morphology. Experiments are performed at Idaho National Laboratory using an experimental device capable of applying internal pressure and independent axial load to commercial nuclear cladding at elevated temperatures with stress- or strain-controlled experimental capability. X-ray diffraction and electron backscatter diffraction are used for microstructure analysis. Rheological models are used to visualize the multiaxial stress-strain relationships and isolate elastic, plastic, and viscoplastic material properties for analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2018

Design and Thermal Analysis for Irradiation of Silicon Carbide Joint Specimens in the High Flux Isotope Reactor

This report provides a summary of the irradiation vehicle design and thermal analysis of SiC joint specimens planned for irradiation in the flux trap of the High Flux Isotope Reactor (HFIR). Two different capsule designs will be used to accommodate the two different specimen geometries: a small torsion joint specimen geometry to measure mechanical and thermal properties, and a tube and end plug joint representative cladding geometry to demonstrate strength and hermeticity retention. The capsule designs, with target temperatures of 350° and 750°C, will accommodate either sixteen torsion joint specimens or one tube end plug joint specimen. Three joint variations will be studied in each capsule design: a hybrid SiC (preceramic polymer with chemical vapor deposition (CVD) SiC), a transient eutectic phase (TEP) process, and an oxide process.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

Performance Analysis of Silicon Carbide Composite Clad Uranium Carbide Fuel for a Long-Life Gas-Cooled Fast Reactor Under Normal Operation—Part I: Design Criteria and Material Data

Not provided.

Nuclear Science & Technology↗

DOE OSTI2017

Hydride Microstructure at the Metal-Oxide Interface of a Zircaloy-4 Fuel Clad from the H.B. Robinson Nuclear Reactor

During nuclear reactor operation, some of the hydrogen that is produced by the water side corrosion is uptaken by cladding. When the uptaken hydrogen content exceeds its solubility limit in the cladding at a specific temperature, it precipitates as hydride particles in the cladding. This process occurs immediately at the metal-oxide interface forming a hydride rim because of the temperature gradient in the cladding. The presence of hydride rim and its microstructure severely reduces the cladding strength and can induce crack initiation and propagation during design basis accidents, transportation, and wet/dry storage. Because hydrides platelets are one of the potent crack initiation sites, microstructural characterization of hydride rim becomes essential to the safe operation of nuclear reactor and spent nuclear fuel retrievability. Therefore, we investigate the hydride rim microstructure at the metal oxide interface using scanning transmission electron microscopy (S/TEM) with Energy Dispersive X-ray Spectroscopy (EDS) that allows for the microstructural and local chemistry characterization of hydride precipitates to be determined, and enables a relationship to be derived on how the precipitate sites are affected by the oxide and their complex stacking behavior of the precipitates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2019

Developing a Macro-scale SiC-cladding Behavior Model Based on Localized Mechanical and Thermal Property Evaluation on Pre- and Post-Irradiation SiC-SiC Composites (Final Report)

Silicon carbide is being investigated for accident tolerant fuel cladding applications due to its good neutronic performance, high temperature strength, exceptional stability under irradiation, and reduced oxidation compared to Zircaloy under accident conditions. The development and investigation of these materials is particularly important in the light of the Fukushima event and subsequent emphasis in DOE on accident tolerant fuel (ATF) concepts. In this work, we propose to develop and improve upon existing small-scale mechanical and thermal characterization methods, including micro-cantilever bend tests and fiber push-out tests, and time-domain thermo-reflectance measurements. These techniques will be applied to evaluate micro-scale properties of SiC-SiC composite constituents (matrix, fibers, interphase). The results will be coupled with meso-scale fiber and void structural information and be used as input to develop a comprehensive, finite element-based model based on constituent properties. The goal of this multi-scale model is to be used to predict anisotropic mechanical and thermal cladding behaviors. The model will be benchmarked against measurements of bulk properties and validated for radiation-damaged materials by utilizing irradiated SiC-SiC composites available from General Atomics. The characterization approach developed under this program will have particular application in the property prediction of reactor irradiated materials, as only small volumes need to be tested, minimizing associated hazards and costs. The micro-scale test methods developed here will be used along with meso-scale structural data to inform a finite element model of the full SiC-based cladding system. This model will capture fabrication and irradiation effects and importantly include for the first-time separate material data for each system component. The incorporation of these micro-scale effects will lead to a more accurate model of SiC-SiC composite behavior, enabling further advancements in the development and design of SiC-based materials for improved fuel cladding performance. The aim of this work is to develop advanced localized material characterization techniques to directly measure mechanical and thermal properties of the individual constituents of SiC-based claddings at the relevant micro-scale. SiC-SiC composites will be evaluated before and after irradiation and these results will be coupled with macro-scale properties and microstructural information in order to provide the input parameters for a comprehensive finite element model, which will be developed in this program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Off-Gas Design and Testing from Advanced Chlorination Process

Chlorination of Zr alloy cladding with sulfur-chloride reagents is being considered as a means of separating the main metal from alloying elements, imbedded U, actinides, and fission and activation products to purify the Zr. This would allow the Zr to be disposed of as low-level nuclear waste or possibly be recycled. A multistage process was developed that involves several steps and waste streams. Recycling of sulfur-chloride reagents S 2 Cl 2 and SOCl 2 is planned to minimize the waste stream. The generation of off-gas and entrainment of volatiles is anticipated to be minimized. However, given the complex nature of spent nuclear fuel (SNF), some volatile components will be generated, including the solvents themselves; Cl 2 used for the regeneration of S 2 Cl 2 ; volatile fission product chlorides, such as Sb and 3 H; and chlorinated alloying components, such as Sn, Nb, Fe, and Mo. This report discusses the chemical phenomena that might give rise to volatile species and their planned capture. The volatility of the transition metals will depend on their oxidation state and the compounds that are formed, such as Zr tritide. Loading radionuclides in the process off-gas will depend on the inputs to the process. For instance, processing separated Zr to reduce waste will have a much lower loading of radionuclides than if alternative chlorination were used for decladding SNF. Much of the volatile process streams will be part of the solvent recycling, which may involve online scrubbing. Generally, a caustic scrubber should be included in the off-gas to remove acidic vapors (e.g., Cl 2 , SOCl 2 ). The decontamination procedures for removing these species could involve pretreatment (i.e., heating) options or reduction by contact with H 2 . This report discusses these options along with a framework for testing these alternatives in future experiments. Technologies for off-gas capture will leverage those developed in the Materials Recovery and Waste Forms program.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2019

Post-irradiation Examinations of Accident Tolerant Fuel Candidates with Iron-alloy Cladding

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced Accident Tolerant Fuels (ATF) for Light Water Reactors (LWRs). The scoping studies, referred to as ATF 1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of iron-based cladding. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33® cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures compared to standard LWR irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to confirm this hypothesis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2016

Corrosion resistant coatings for zirconium-alloy cladding with improved accident tolerance

The Westinghouse-led accident tolerant fuel (ATF) program is evaluating Accident Tolerant Fuel (ATF) coatings of MAX phase (Ti{sub 2}AlC) and multi-layer Ti{sub x}Al{sub 1-x}N/TiN to enhance the oxidation resistance of zirconium alloy fuel cladding in both normal operation and beyond design-based conditions of light water reactors. A variety of coating technologies have been applied to deposit these coating materials onto Zircaloy-4 or Zirlo sheets and tubes, including cold spray and cathodic arc-physical vapor deposition (CA-PVD). Neutronic analysis using the elemental compositions of the coating materials showed that the coating thicknesses should be less than 30 μm for most coating materials to avoid non-negligible economic penalty. The coated samples were autoclave tested in water at 360 Celsius degrees and 150 bar or in steam at 427 Celsius and 103 bar for corrosion resistance evaluation. The initial Ti{sub 2}AlC coating made by using large particle size MAX phase powder and cold spray deposition did not provide the desired corrosion resistance due to un-optimized microstructure and porosity. Subsequent optimization including reduction in particle size and tuning of cold spray deposition parameters resulted in denser coatings less than 30 microns in thickness. Optimization of process conditions resulted in reduced oxidation kinetics and showed that the coating acts as an effective barrier to prevent the zirconium substrate from oxidizing in accident condition temperatures. High purity Ti{sub 2}AlC powder is needed to further improve oxidation resistance of the Ti{sub 2}AlC coating. The oxidation resistance of pure monolithic MAX phase compound was also found to be remarkable, and the weight gain was only 1.85 mg/cm{sup 2} for 96 hours exposure in 1200 C. degrees steam, which is consistent with the literature. The corrosion resistance of the TiAlN/TiN multilayer coating was excellent. The weight gain was negligible and no oxidation was observed on the surface of zirconium-alloy at the coating-substrate interface. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗