Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Mechanisms of degradation and failure in a plasma deposited thermal barrier coating

Failure of a two layer plasma deposited thermal barrier coating is caused by cyclic thermal exposure and occurs by spallation of the outer ceramic layer. Spallation life is quantitatively predictable, based on the severity of cyclic thermal exposure. This paper describes and attempts to explain unusual constitutive behavior observed in the insulative ceramic coating layer, and presents details of the ceramic cracking damage accumulation process which is responsible for spallation failure. Comments also are offered to rationalize the previously documented influence of interfacial oxidation on ceramic damage accumulation and spallation life.

Demasi-Marcin, Jeanine T.↗
NASA NTRS1992

Durability evaluation of photovoltaic blanket materials exposed on LDEF tray S1003

Several candidate protective coatings on Kapton and uncoated Kapton were exposed to the low Earth orbital (LEO) environment on the Long Duration Exposure Facility (LDEF) to determine if the coatings could be used to protect polymeric substrates from degradation in the LEO environment. The coatings that were evaluated were 700 A of aluminum oxide, 650 A of silicon dioxide, and 650 A of a 4 percent polytetrafluoroethylene-96 percent silicon dioxide mixed coating. All of the coatings evaluated were ion beam sputter deposited. These materials were exposed to a very low atomic oxygen fluence (4.8 x 10 exp 19 atoms/sq. cm) as a result of the experiment tray being located 98 degrees from the ram direction. As a result of the low atomic oxygen fluence, determination of a change in mass was not possible for any of the samples including the uncoated Kapton. There was no evidence of spalling of any of the coatings after the approximately 33,600 thermal cycles recorded for LDEF. The surface of the uncoated Kapton, however, did show evidence of grazing incidence texturing. There was a 7-8 percent increase in solar absorptance for the silicon dioxide and aluminum oxide coated Kapton and only a 4 percent increase for the mixed coating. It appears that the addition of a small amount of fluoropolymer may reduce the magnitude of absorptance increase due to environmental exposure. Thermal emittance did not change significantly for any of the exposed samples. Scanning electron microscopy revealed few micrometeoroid or debris impacts, but the impact sites found indicated that the extent of damage or cracking of the coating around the defect site did not extend beyond a factor of three of the impact crater diameter. This limiting of impact damage is of great significance for the durability of thin film coatings used for protection against the LEO environment.

Sharon K Rutledge↗
NASA NTRS1987

Thermal barrier coating life prediction model

The objectives of this research were to determine the predominant modes of degradation of a plasma sprayed thermal barrier coating (TBC) system, and then to develop and verify life prediction models accounting for these degradation modes. The TBC system consists of a low pressure plasma sprayed (LPPS) bond coat layer of Ni-22Cr-10Al-O.3Y, an air plasma sprayed (APS) yttria partially stabilized zirconia (ZrO sub 2-8Y sub 2 O sub 3) top coat on a conventionally cast Rene 80 (Ni base) substrate. Thermal cycle testing of TBCs was employed to evaluate the effect of coating edges, bond coat oxidation, bond coat creep, top coat thickness, and bond coat thickness.

Pilsner, B.↗
NASA NTRSDate not supplied

Exposure of Highly Reflective Far-Ultraviolet Coatings to LEO Environment for TRL Advancement for the Habitable Worlds Observatory

Over the past several years, our team at the NASA Goddard Space Flight Center (GSFC), in collaboration with the Jet Propulsion Laboratory (JPL) and the Naval Research Laboratory (NRL), have developed several new protected Al coating technologies with improved Far-Ultraviolet (FUV) reflectance performance and more robust environmental stability. These include Al protected with lithium-based fluoride (LiF) coatings such as hot deposited LiF (eLiF), XeF 2 -passivated LiF coatings (XeLiF), Li 3 AlF 6 overcoats, AlF 3 (plasma passivated), and XeF 2 passivated MgF 2 coatings (XeMgF 2 ). However, despite these developments, relatively little experimental information exists regarding the long-term stability of these coatings after simultaneous exposure to the Low Earth Orbit (LEO) environment. To evaluate their environmental durability and advance their Technology Readiness Level (TRL), representative samples of these coating technologies, Al+XeLiF, Al+eLiF, Al+Li 3 AlF 6 , Al+AlF 3 , Al+XeMgF 2 , and bare Al as reference samples, were flown onboard the International Space Station (ISS) as part of the Materials International Space Station Experiment 20 (MISSE-20). The MISSE platform is operated by Aegis Aerospace for relatively long-duration (e.g. 6 months) external exposure experiments in a space environment. The coatings were deposited on ULE and Zerodur substrates, and witness samples deposited on the same coatings runs, but on glass slides were left on Earth as control. A subset of the flight samples were fitted with MgF 2 windows to reduce direct exposure to atomic oxygen (AO) and charged particles, and still let through UV and other types of radiation on these samples. After approximately 6 months of exposure in the forward-facing (RAM) direction, the samples were returned to Earth and characterized by performing FUV/NUV/VIS/NIR reflectance measurements to quantify degradation, spectroscopic ellipsometry to evaluate coating thickness and optical constants, atomic force microscopy (AFM) to quantify surface roughness evolution during the flight in the ISS. The MgF 2 protective windows were also analyzed through FUV transmission measurements. Comparison with the witness samples left on the ground and with the flown bare Al samples (with just the naturally occurring Al 2 O 3 layer) provided a quantitative assessment of coating thickness variations, optical performance degradation, and morphological changes induced by prolonged exposure to the LEO environment.

Far Ultraviolet (FUV)↗
NASA NTRS1995

Thermal Stability of Hi-Nicalon SiC Fiber in Nitrogen and Silicon Environments

The room temperature tensile strength of uncoated and two types of pyrolytic boron nitride coated (PBN and Si-rich PBN) Hi-Nicalon SiC fibers was determined after 1 to 400 hr heat treatments to 1800 C under N2 pressures of 0.1, 2, and 4 MPa, and under 0.1 Mpa argon and vacuum environments. In addition, strength stability of both uncoated and coated fibers embedded in silicon powder and exposed to 0.1 MPa N2 for 24 hrs at temperatures to 1400 C was investigated. The uncoated and both types of BN coated fibers exposed to N2 for 1 hr showed noticeable strength degradation above 1400 C and 1600 C, respectively. The strength degradation appeared independent of nitrogen pressure, time of heat treatment, and surface coatings. TEM microstructural analysis suggests that flaws created due to SiC grain growth are responsible for the strength degradation. In contact with silicon powder, the uncoated and both types of PBN coated fibers degrade rapidly above 1350 C.

Bhatt, R. T.↗
NASA NTRSDate not supplied

Thermal Materials and Coatings for Near Rectilinear Halo Orbit (NRHO)

Passive thermal control of a spacecraft is reliant on external surface optical properties (solar absorptivity and IR emissivity), which degrade over time depending on length of mission, material or coating, and natural and induced environments. Understanding the degradation and resulting End of Life (EOL) optical properties enables optimization of the thermal performance and reduces risk. The environmental factors that affect degradation of materials and coatings include UV, solar wind, vacuum, contamination, lunar dust, atomic oxygen, and more. Future spacecraft such as Gateway will be flying in the Near Rectilinear Halo Orbit (NRHO), an environment that has not been flown before and environmental factors are different from Low Earth Orbit. There is no on orbit data for materials in this environment, and optical property data from on-orbit and ground experiments for other environments is of limited use. This 1.5 hour short course will explore optical properties and degradation by introducing the expected environment of NRHO, types of materials and coatings that could be used, how to estimate their EOL properties, and future work. This course will focus on the NRHO environment, but it will be beneficial for anyone interested in optical property degradation in the space environment.

Optics↗
NASA NTRS2017

Coatings for Oxidation and Hot Corrosion Protection of Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can potentially seriously degrade the life of the disk. Application of metallic coatings are one means of protecting disk alloys from this environmental attack. However, simply the presence of a metallic coating, even without environmental exposure, can degrade the LCF life of a disk alloy. Therefore, coatings must be designed which are not only resistant to oxidation and corrosion attack, but must not significantly degrade the LCF life of the alloy. Three different Ni-Cr coating compositions (29, 35.5, 45wt. Cr) were applied at two thicknesses by Plasma Enhanced Magnetron Sputtering (PEMS) to two similar Ni-based disk alloys. One coating also received a thin ZrO2 overcoat. The coated samples were also given a short oxidation exposure in a low PO2 environment to encourage chromia scale formation. Without further environmental exposure, the LCF life of the coated samples, evaluated at 760C, was less than that of uncoated samples. Hence, application of the coating alone degraded the LCF life of the disk alloy. Since shot peening is commonly employed to improve LCF life, the effect of shot peening the coated and uncoated surface was also evaluated. For all cases, shot peening improved the LCF life of the coated samples. Coated and uncoated samples were shot peened and given environmental exposures consisting of 500 hrs of oxidation followed by 50 hrs of hot corrosion, both at 760C). The high-Cr coating showed the best LCF life after the environmental exposures. Results of the LCF testing and post-test characterization of the various coatings will be presented and future research directions discussed.

LCF life↗
NASA NTRS2019

Sublimation Protection Coatings for Thermoelectric Materials for Space Power Applications

The compounds such as Yb14MnSb11 are relatively new p-type thermoelectric materials, respectively. NASA's interest in these material are to replace the state-of-the-art Si-Ge legs of the current radioisotope thermoelectric generators (RTGs). Ideally, the hot end of this leg would operate at 1000 degrees C in the vacuum of space. These materials, however, suffer from a high sublimation rate at elevated temperatures and would require a coating in order to survive the required RTG lifetime of 14 years. The purpose of present work is to develop sublimation protection coatings for Yb14MnSb11 at temperatures up to 1000 degrees C. Coatings for Yb14MnSb11 present many challenges. The coating must not significantly react or interdiffuse with the substrate thereby degrading the substrate or consuming the coating, must remain intact and not crack or spall during thermal cycling prior to launch, and must be a good insulator both electrically and thermally so as not to provide a short circuit for either electron flow or heat through the coating rather than through the leg. Based on these requirements, several oxides have been selected as possible coating candidates. This paper discusses the development of slurry processes to deposit these oxides coatings on thermoelectric materials.

Sublimation↗
NASA NTRS2017

Advanced Environmental Barrier Coating Development for SiC-SiC Ceramic Matrix Composite Components

This presentation reviews the NASA advanced environmental barrier coating (EBC) system development for SiC-SiC Ceramic Matrix Composite (CMC) combustors particularly under the NASA Environmentally Responsible Aviation, Fundamental Aeronautics and Transformative Aeronautics Concepts Programs. The emphases have been placed on the current design challenges of the 2700-3000F capable environmental barrier coatings for low NOX emission combustors for next generation turbine engines by using advanced plasma spray based processes, and the coating processing and integration with SiC-SiC CMCs and component systems. The developments also have included candidate coating composition system designs, degradation mechanisms, performance evaluation and down-selects; the processing optimizations using TriplexPro Air Plasma Spray Low Pressure Plasma Spray (LPPS), Plasma Spray Physical Vapor Deposition and demonstration of EBC-CMC systems. This presentation also highlights the EBC-CMC system temperature capability and durability improvements under the NASA development programs, as demonstrated in the simulated engine high heat flux, combustion environments, in conjunction with high heat flux, mechanical creep and fatigue loading testing conditions.

CMAS↗
NASA NTRS1986

Thermal barrier coating life prediction model

The objectives of this program are to determine the predominant modes of degradation of a plasma sprayed thermal barrier coating system, and then to develop and verify life prediction models accounting for these degradation modes. The program is divided into two phases, each consisting of several tasks. The work in Phase 1 is aimed at identifying the relative importance of the various failure modes, and developing and verifying life prediction model(s) for the predominant model for a thermal barrier coating system. Two possible predominant failure mechanisms being evaluated are bond coat oxidation and bond coat creep. The work in Phase 2 will develop design-capable, causal, life prediction models for thermomechanical and thermochemical failure modes, and for the exceptional conditions of foreign object damage and erosion.

Pilsner, B. H.↗
NASA NTRS1999

Effects Investigated of Ambient High-Temperature Exposure on Alumina-Titania High-Emittance Surfaces for Solar Dynamic Systems

Solar-dynamic space power systems require durable, high-emittance surfaces on a number of critical components, such as heat receiver interior surfaces and parasitic load radiator (PLR) elements. An alumina-titania coating, which has been evaluated for solar-dynamic heat receiver canister applications, has been chosen for a PLR application (an electrical sink for excess power from the turboalternator/compressor) because of its demonstrated high emittance and high-temperature durability in vacuum. Under high vacuum conditions (+/- 10(exp -6) torr), the alumina-titania coating was found to be durable at temperatures of 1520 F (827 C) for approx. 2700 hours with no degradation in optical properties. This coating has been successfully applied to the 2-kW solar-dynamic ground test demonstrator at the NASA Lewis Research Center, to the 500 thermal-energy-storage containment canisters inside the heat receiver and to the PLR radiator. The solar-dynamic demonstrator has successfully operated for over 800 hours in Lewis large thermal/vacuum space environment facility, demonstrating the feasibility of solar-dynamic power generation for space applications.

deGroh, Kim K.↗
DOE OSTI2021

High-temperature oxidation and quenching of chromium-coated zirconium alloy ATF cladding tubes with and w/o pre-damage

Chromium-coated zirconium alloys are one of the promising candidates for accident-tolerant fuel cladding (ATF) tubes for light water reactors (LWRs). In this study, the high temperature oxidation and degradation of two types of Cr coatings (cold spray and physical vapor deposition) with and without pre-damage by scratches were investigated on prototype rod segment samples filled with ZrO 2 pellets and tightly sealed with welded end caps. Isothermal tests at 1100 and 1200 °C were terminated by quenching with water; transient tests were performed up to 1500–1600 °C until complete coating failure. The positive effect of both types of Cr coatings was observed in all tests. Pre-damaged specimens showed only locally increased oxidation of the scratched zone, but no negative effects on the adjacent Cr coating. Finally, the behavior of the two types of coatings is compared and the degradation mechanisms are discussed based on hydrogen release data, extensive metallographic post-test examinations, and the current state of global research.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasma mirror focal spot quality for glass and aluminum mirrors for laser pulses up to 20 ps

High-intensity short-pulse lasers are being pushed further as applications continue to demand higher laser intensities. Uses such as radiography and laser-driven particle acceleration require these higher intensities to produce the necessary x-ray and particle fluxes. Achieving these intensities, however, is limited by the damage threshold of costly optics and the complexity of target chambers. This is evidenced by the Advanced Radiographic Capability (ARC) short-pulse laser at the National Ignition Facility (NIF) at the Lawrence Livermore National Laboratory, producing four high-energy ≈1 kJ laser pulses at 30 ps pulse duration, being limited to an intensity of 10 18 W/cm 2 by the large focal spot size of ≈100 µm. Due to the setup complexity of NIF, changing the location of the final focusing parabola in order to improve the focal spot size is not an option. Therefore, this leads to the possible use of disposable ellipsoidal plasma mirrors (PMs) placed within the chamber, close to the target in an attempt to refocus the four ARC beams. However, the behavior of PMs at these relatively long pulse durations (tens of picoseconds) is not well characterized. The results from the COMET laser at the Jupiter Laser Facility carried out at 0.5 to 20 ps pulse durations on flat mirrors are presented as a necessary first step towards focusing curved mirrors. The findings show defocusing at longer pulse durations and higher intensities, with less degradation when using aluminum coated mirrors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Spatiotemporal Variability in Wind Turbine Blade Leading Edge Erosion

Wind turbine blade leading edge erosion (LEE) reduces energy production and increases wind energy operation and maintenance costs. Degradation of the blade coating and ultimately damage to the underlying blade structure are caused by collisions of falling hydrometeors with rotating blades. The selection of optimal methods to mitigate/reduce LEE are critically dependent on the rates of coating fatigue accumulation at a given location and the time variance in the accumulation of material stresses. However, no such assessment currently exists for the United States of America (USA). To address this research gap, blade coating lifetimes at 883 sites across the USA are generated based on high-frequency (5-min) estimates of material fatigue derived using a mechanistic model and robust meteorological measurements. Results indicate blade coating failure at some sites in as few as 4 years, and that the frequency and intensity of material stresses are both highly episodic and spatially varying. Time series analyses indicate that up to one-third of blade coating lifetime is exhausted in just 360 5-min periods in the Southern Great Plains (SGP). Conversely, sites in the Pacific Northwest (PNW) exhibit the same level of coating lifetime depletion in over three times as many time periods. Thus, it may be more cost-effective to use wind turbine deregulation (erosion-safe mode) for damage reduction and blade lifetime extension in the SGP, while the application of blade leading edge protective measures may be more appropriate in the PNW. Annual total precipitation and mean wind speed are shown to be poor predictors of blade coating lifetime, re-emphasizing the need for detailed modeling studies such as that presented herein.

Pryor, Sara C. (ORCID:0000000348473440)↗
NASA NTRS1972

Low-energy particle radiation environment at synchronous altitude

The degradation of thermal control coatings of satellites due to the effects of low energy charged particles in the space environment is discussed. Data obtained from ATS-5 satellite measurement of proton and electron fluxes are presented. The variations in electron density, proton density, and magnetic activity are presented to show correlations which exist between these space factors.

Shelley, E. G.↗
NASA NTRS1985

Orbital atomic oxygen effects on thermal control and optical materials - STS-8 results

The effects of exposing 23 specimens of optical and thermal control materials to space at 120 km altitude for over 40 hrs during the STS-8 mission are discussed. Ten samples of paint targeted for the Space Telescope (ST) and the Tethered Satellite were exposed, and included polyurethane, oxide, silicone, and glossy black and white samples which were scanned for alterations in the optical properties after being retrieved. Nine mirror-type materials were also investigated, along with silver specimens typical of solar cell interconnects. The oxygen flow at the orbital altitude was 3.5 x 10 to the 20th atoms/cu cm. The exposures caused no degradation of the magnesium fluoride mirror coatings, while the Kapton coating for the ST solar cell panels showed evidence of losing thickness. The Ag solar cell contacts will require coatings to extend their lifetimes. Overcoatings were also proven necessary for inhibiting degradation of painted surfaces.

Whitaker, A. F.↗
NASA NTRS1988

Response of composite materials to the Space Station orbit environment

The rationale for selecting composite materials with an anodized aluminum foil coating for the Space Station is presented. Data on the effects of the space service environment on these materials are given. Results are also presented on the effect of optical properties of an aluminum/aluminum oxide coating on the thermal balance of the cylindrical structural members. The resistance of this coating to solar ultraviolet degradation is discussed.

Tompkins, S. S.↗