Search NASA⌕ Search

SEARCH · Search NASA

Results for “IRRADIATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of high-dose neutron irradiation at light-water reactor relevant temperature on the mechanical properties of SiC/SiC composites

For this study, the neutron dose-dependent evolutions and the underlying mechanisms of properties of SiC fiber-reinforced SiC matrix (SiC/SiC) composites at a temperature relevant to light-water reactors (∼600 K) were investigated and analyzed. Chemical vapor infiltrated (CVI) SiC/SiC composites reinforced with Hi-Nicalon Type S or Tyranno SA3 fiber were neutron-irradiated to doses up to 30 dpa. The irradiated composites retained their flexural strengths. The thermal diffusivity and dimensional changes were mostly retained from 2.0 to 30.2 dpa. Discrepancies in irradiation responses among CVI SiC/SiC composites from different sources were found. Additional microstructural analysis using Raman spectroscopy and numerical analysis on irradiation effect on residual stress were used to explain how the microstructural variables, especially of carbon interphases, affect the mechanical properties in the 30–40 dpa dose range.

Continuous fiber-reinforced ceramic matrix composi↗
DOE OSTI2025

High resolution microstructural, chemical studies and localized burnup analysis in an irradiated U–10Zr metallic fuel

This study involves high resolution characterization of a sodium bonded solid uranium (U)-10 wt% zirconium (Zr) metallic fuel irradiated in Fast Flux Test Facility (FFTF). The fuel centerline temperature during irradiation was estimated to be around 675 °C with the peak burnup 13.1 atomic percent. Samples for transmission electron microscopy (TEM) and atom probe tomography (APT) were prepared from different regions/zones in the fuel cross section radially to elucidate the microstructural changes and chemical redistribution of solute elements as well as fission products during irradiation experiment. TEM results indicate the irradiation in fast flux testing leads to the formation of extensive Zr-rich precipitates with varying sizes in the U–Zr fuel matrix. APT analysis performed to investigate redistribution of Zr, U and fission products along the radial direction of fuel pin showed Zr-rich precipitates entrapping the fission products in higher concentration as compared to the α-U phases. Here, the local burnup ( 235 U depletion) is found to be consistent, calculated by quantification of 235 U, 236 U and 238 U isotopes from mass spectrum obtained from APT along the radial direction. Zr-rich precipitation and its implication on fuel constitutional redistribution are discussed based on SEM, TEM and APT results.

APT↗
DOE OSTI2026

Microstructural stability of irradiated yttrium hydride under thermal cycles

Hydrides that retain their hydrogen in service are critical for advanced microreactor and space nuclear systems. Hydrogen retention is affected by evolving microstructure under temperature and irradiation extremes. This study investigated microstructural features in neutron-irradiated yttrium hydride and the stability of these features under thermal cycles. Differential scanning calorimetry was used to determine hydrogen desorption and temperatures at which significant phase changes are occurring, and transmission electron microscopy was used for microstructural analysis after each thermal cycle. Cyclic heating led to crystallization and epitaxial growth of surface oxidation and dehydriding of the matrix. Other features such as the bulk matrix crystal structure, irradiation-induced cavities, and matrix precipitation remained constant after thermal cycling. Results allow us to design better hydride alloys through microstructure tailoring and potential irradiation conditioning treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Forced flow transient safety analysis of irradiation device with adjustable orifice for research reactor fuel assemblies

The Belgium Reactor 2 (BR2) of the Belgian Nuclear Research Centre (SCK CEN) has several irradiation devices or rigs that are dedicated to the fuel performance and qualification demonstration testing of research reactor fuels. In support of the U.S. High Performance Research Reactor (USHPRR) LEU conversion project, a new flexible irradiation apparatus, MUSTANG-R, has been constructed. SCK CEN has completed the design and safety study, in cooperation with Idaho National Laboratory (INL) and Argonne National Laboratory (ANL), to allow for the irradiation testing of a full-size fuel assembly in a 200 mm diameter channel in the BR2 reactor. The moveable valve is a key design feature of the device and acts like an adjustable orifice enhancing or restricting the flow through a coolant channel inlet located in the BR2 upper plenum. This moveable valve allows the flow through the device to be adjusted prior to each BR2 cycle to obtain the necessary conditions for the fuel qualification test. This ensures accurate and representative thermal-hydraulic conditions of the fuel design are achieved. The device was designed and qualified as passively safe, implying verification by a combination of mechanical and thermal-hydraulic analysis and testing. This includes characterization of the safety margin required for a scenario where the moveable valve is assumed to be erroneously closed during irradiation. A simplified and conservative method is proposed for analyzing the corresponding forced flow transient using a critical heat flux criterion. In conclusion, this allows the required minimum valve opening to be determined for the experiments' design and safety studies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Results of the AGR-5/6/7 UCO TRISO fuel irradiation test in the Advanced Test Reactor

AGR-5/6/7 was the last in a series of irradiation experiments sponsored by the U.S. Department of Energy in support of the development and qualification of TRISO coated particle fuel for use in a high-temperature gas-cooled reactor. This experiment was conducted to verify the performance of the reference-design TRISO-coated low-enriched UCO fuel for modular high-temperature gas-cooled reactor normal operating conditions and to explore fuel performance at temperatures substantially beyond those typical of normal operation. A total of 194 UCO fuel compacts in five capsules were irradiated in the Advanced Test Reactor for 360.9 effective full-power days, achieving final burnup ranging from 5.66% to 15.26% fissions per initial heavy metal atom and fast neutron fluence ranging from 1.62 × 10 25 to 5.55 × 10 25 n/m 2 (E > 0.18 MeV). Calculated time-averaged fuel temperatures ranged from 467 °C to 1432 °C, with a peak fuel temperature of 1536 °C. During the first five irradiation cycles (∼180 effective full-power days), 85m Kr fission gas release-rate-to-birth-rate ratios were 10 −7 –10 −6 , indicating no particle failures. Near the end of the sixth cycle, a substantial number of in-pile particle failures occurred in Capsule 1. The fission gas release from this capsule impacted the readings from the other four capsules and led to unreliable fission gas release measurements for all capsules during the last four cycles. A preliminary post-irradiation examination of Capsule 1 fuel and internal components revealed the in-pile particle failures resulted from operational issues with the capsule, not subpar performance of the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Intrinsic property of defective β-Ga 2 O 3 to self-heal under ionizing irradiation

Damage evolution and phase stability in defective β-Ga 2 O 3 and an irradiation-converted γ-Ga 2 O 3 layer have been studied under ionizing irradiation at 300 K. By exploring athermal nonequilibrium processes in β-Ga 2 O 3 , we succeed in identifying a self-healing mechanism that enables recovery pre-existing damage, characterized by a recovery cross-section of ~0.17 nm 2 . Remarkably, this study further demonstrates that the crystallinity of the irradiation-converted γ-Ga 2 O 3 layer improves under ionizing irradiation. More importantly, X-ray diffraction analysis reveals that the highly-strained 𝛾 -phase transforms into a highly-crystalline structure without film disintegration, contrasting to that reported for isochronal annealing at 1000 K. The inelastic thermal spike calculations provide insights into the important effects of energy transfer to electrons in reordering the local atomic arrangement of both defective β- Ga 2 O 3 and 𝛾-Ga 2 O 3 . This behavior suggests a pathway for low-temperature crystallization, offering a promising strategy for fabricating ultrahigh-speed non-volatile memory devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Anisotropic growth of Ni 2 (Cr,Mo) ordered phase in proton irradiated Ni-Cr-Mo alloys

Ni-Cr-Mo alloys are widely used in the nuclear industry as structural materials due to their high temperature strength and corrosion resistance. Ni-based alloys containing around 33 at.% (Cr+Mo) developed a long-range ordered Ni 2 (Cr,Mo) phase after thermal aging and/or irradiation. The ordering mechanism for thermally-aged Ni 2 (Cr,Mo) phase is well-understood, characterized to be sluggish, homogeneous, and isotropic. The ordering mechanism for irradiation-induced Ni 2 (Cr,Mo) phase is not fully understood, characterized as having rapid formation and demonstrating anisotropic precipitation. Here, this work elucidates the anisotropic precipitation and anisotropic precipitation mechanism of Ni 2 (Cr,Mo) after proton irradiation in Ni-Cr-Mo alloys. Selected area electron diffraction and bright-field scanning transmission electron microscopy imaging are used to image superlattice reflections from the ordered phase and irradiation-induced defects, respectively. A higher degree of anisotropic precipitation is observed with increasing dislocation loop and void size; a phenomenon not observed in thermally aged samples.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Worldwide benchmarking of cost-effective radiometers for direct and diffuse irradiance

Solar energy projects can benefit from direct normal irradiance (DNI) and diffuse horizontal irradiance (DHI) measurements during all project phases. Several commercial measurement systems for DNI and DHI are available. Sun trackers with pyranometers and pyrheliometers can provide highly accurate measurements but are often impractical in solar energy applications. For less expensive and more robust sensors, it is often unclear which accuracy can be expected under a project site's specific atmospheric conditions. We address this challenge through our dedicated experimental comparison of relevant sensor systems (rotating shadowband irradiometer [short RSI], Delta-T SPN1, EKO MS-90, PyranoCam, Sunto CaptPro, Kipp & Zonen CSD3) at up to six sites worldwide. The RSI systems (rRMSD 3 to 8.6%, DNI; 4.8 to 7.6%, DHI) and PyranoCam (rRMSD 2.6 to 5.2%, DNI; 4.4 to 5.8%, DHI) exhibit similar error metrics and are the most accurate systems in the test. Delta-T SPN1 and EKO MS-90 (rRMSD 6.8 to 15%, DNI; 10.6 to 20.1%, DHI) but especially Kipp & Zonen CSD3 and Sunto CaptPro show significant deviations (rRMSD 17.7 to 20%, DNI; 33 to 58%, DHI). We evaluate the influence of relevant atmospheric parameters on the sensors' accuracies by a rather unique measurement setup. MS-90's DNI errors depend on DNI itself, with overestimations for low reference DNI. The deviations of SPN1's DHI and DNI measurements increase sharply in situations with high circumsolar irradiance. Also CaptPro and CSD3's increased measurement errors are related to circumsolar irradiance. For RSI and PyranoCam, only moderate influences on the measurements are identified, indicating a general applicability of these instruments.

14 SOLAR ENERGY↗
DOE OSTI2025

Defect-induced phonon-resonant scattering and its influence on thermal transport of irradiated thorium-dioxide

Thermal transport in proton irradiated thorium-dioxide (ThO 2 ) is investigated. Using a combination of experiments and first-principles computational framework, the role of lattice defects on thermal conductivity is analyzed. A resonant-phonon scattering mechanism beyond the traditionally considered Rayleigh scattering is found to significantly influence low-temperature thermal transport in the presence of irradiation-induced point defects. The existence of localized phonon modes associated with irradiation-induced defects is suggested by the inability of the first-principles based thermal conductivity model—which considers only three-phonon interactions and phonon-defects scattering using the Tamura formalism—to predict the experimental results, unless a resonant scattering mechanism is included. The emergence of additional peaks in the Raman spectra in the proximity of phonon-resonant frequency provides further evidence for the existence of localized modes. Coupled with a microstructure evolution model, this analysis enables more accurate analysis for contrasting the contributions of different phonon scattering mechanisms across all irradiation doses and temperatures.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Computational Thermal Hydraulics of a High-Performance Low-Enriched-Uranium Annular Target for HFIR Irradiation

Molybdenum-99 has historically been generated via isolation from fissioned highly enriched uranium (HEU) targets. Here, this isotope is in high demand due to its daily use across the world in radiopharmaceutical medical procedures. The primary objective of this work was to design and analyze an experimental target assembly containing one low-enriched-uranium (LEU) annular target for irradiation at the High Flux Isotope Reactor (HFIR). Efforts included incorporating spatially dependent energy sources from neutron and gamma interactions, quantifying thermal contact conductance at material interfaces, performing grid-independent studies, comparing turbulence models, and simulating various steady-state and transient scenarios relevant for irradiation qualification and eventual insertion. These models provide velocity, pressure, and temperature distributions in both space and time. Such results enable the selection of an appropriate irradiation location, fission rate density, and flow-limiting orifice size and demonstrate compliance with HFIR safety requirements such that insertion into the reactor can be approved. This analysis shows that across all scenarios, wetted surface temperatures remain below the coolant saturation temperature with no net vapor formation in the coolant. In every scenario, all components stay below 30% of the aluminum 6061 melting temperature. Computational fluid dynamics and system-level models predict peak target temperatures that agree within 4%, though the predicted axial location of the peak differs by about 10% of the heated length due to differences in flow development length. These results de-risk the irradiation of LEU (annular targets) and strengthen a domestic, HEU-independent 99 Mo supply by providing important fuel performance data to form the foundation for a robust licensing basis.

Molybdenum-99↗
DOE OSTI2025

Photocarrier dynamics at the interface between WS 2 and ozone-irradiated graphene

We investigate the photocarrier properties of heterostructures (HSs) formed by WS 2 and ozone-irradiated graphene (OI-graphene), with a focus on the impact of ozone irradiation. Photoluminescence and Raman spectroscopy reveal a pronounced doping effect induced by ozone irradiation on the graphene layer. Transient absorption measurements demonstrate a substantial suppression of charge transfer efficiency across the interface in the presence of ozone molecules. Spatially resolved pump-probe measurements further show a significant reduction in the diffusion coefficient of photocarriers in WS 2 on OI-graphene compared to that of individual WS 2 monolayers. The slower diffusion suggests enhanced spatial separation of electrons and holes in the WS 2 layer, induced by a built-in electric field at the interface. This effect arises from the combined influences of doping and dielectric property changes caused by ozone molecules. These findings highlight the critical influence of ozone irradiation on graphene and HS interfaces, offering valuable insights for the design of future graphene-based two-dimensional HSs.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Ta–Zr carbides: Synthesis advances via carbothermal reduction and defect evolution observed through transmission electron microscopy ion irradiation

The thermodynamic stability of six distinct compositions within the Zr—Ta—C ternary system is investigated in this study, marking the first report of their synthesis through carbothermic reduction in vacuum. A prolonged annealing process at 2200°C enabled high densification and phase equilibrium. Detailed phase identification and microstructural characterization through microscopy and X-ray diffraction techniques revealed clear compositional trends and stable phase formations. Two compositions ((Ta 0.2 Zr 0.8 )C 0.6 and (Ta 0.5 Zr 0.5 )C 1 ) were selected for ion irradiation experiments using 200 keV Kr + at 600°C—representing the first-ever irradiation study on the Zr—Ta—C system. The findings indicated defect accumulation and nanoscale cavity formation without any evidence of amorphization, highlighting the system's structural stability under irradiation. Together, the synthesis and irradiation results provide a basis for further investigation of the system and suggest its relevance for applications under extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films

High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.

AFM↗
DOE OSTI2025

Report on the Assessment of Ion Irradiations on High Entropy Alloys

Idaho National Laboratory (INL) initiated a joint international effort with the Czech Republic to explore the feasibility of manufacturing High Entropy Alloys for high-temperature nuclear applications using Additive Manufacturing. This effort was funded at INL by the United States Department of Energy’s Office of Nuclear Energy under the Advanced Reactor Technologies and Advanced Materials and Manufacturing Technologies (AMMT) Program. The High Entropy Alloys were specifically designed for the corrosive and irradiation environments as experienced in gas fast reactors, molten salt reactors, and fusion power. These alloys were manufactured by multiple processes to determine the impact of manufacturing processes on the performance of the alloys in corrosive and irradiation environments. Preliminary results show that MoNbTiV and MoNbTi alloys exhibit no degradation after multiple corrosion tests. These MoNbTiV and MoNbTi alloys were also evaluated after irradiation experiments were conducted at the Michigan Ion Beam Laboratory at the University of Michigan, which is the focus of this milestone report. For these irradiation experiments, the MoNbTiV and MoNbTi alloys manufactured by arc melting and Electric Field Assisted Sintering (EFAS) were tested at 500 C at a dose of 30 dpa to evaluate the microstructural stability and decomposition.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Defect Generation and Evolution in Irradiated Epitaxial Films and Heterostructures of Fe 3 O 4 and Cr 2 O 3

Abstract The functionality of nuclear structural materials, sensors, and microelectronics in harsh environments such as radiation relies on understanding defect generation and evolution processes in oxide layers. The initial radiation response of epitaxial thin films of Fe 3 O 4 (111), Cr 2 O 3 (0001), and Fe 3 O 4 (111)/Cr 2 O 3 (0001) heterostructures deposited on Al 2 O 3 (0001) by oxygen‐assisted molecular beam epitaxy and irradiated with 200 keV He + is characterized. X‐ray diffraction and X‐ray absorption near edge spectroscopy showed that the Cr 2 O 3 layers underwent significant lattice expansion and disordering under irradiation, whereas the Fe 3 O 4 layers do not exhibit noticeable changes. In contrast, positron annihilation spectroscopy revealed an evolution of cation vacancy point defects in the Fe 3 O 4 layers into larger vacancy clusters with increasing irradiation, while the cation vacancies in Cr 2 O 3 remained primarily as single vacancies and small clusters. The results suggest that the Fe 3 O 4 lattice can utilize the free volume of the larger vacancy clusters to relax but the small vacancies in the Cr 2 O 3 lattice do not facilitate relaxation. Comparing defect concentrations in the single layer films versus the heterostructure suggests that point defects may cross the interface from Fe 3 O 4 into Cr 2 O 3 . Together, these results enhance the understanding of the initial defect evolution mechanisms in oxide layers in harsh irradiation environments.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Temperature and dose rate effects on dislocation loop formation and decoration in self-ion irradiated high-purity Fe-Cr model alloys

Body-centered cubic (BCC) Fe-based alloys are promising candidate materials for advanced nuclear reactors. A widespread perception is that the addition of Cr favors the formation of ½ <111> dislocation loops. However, the Cr effects on dislocation loop formation/evolution remain unclear due to the limited experimental studies. In this study, we irradiate ultra-high purity bulk BCC Fe-xCr (x = 3, 5, and 8 wt%) with 6.7-8 MeV Fe ions over a wide range of temperatures (Tirr = 250-500 °C) and dose rates (10⁻⁵ to 10⁻³ dpa/s) to two midrange doses (0.35 and 3.5 dpa). The major irradiation-induced microstructures are loop decoration along non-screw dislocation lines at low temperatures and high dose rates as well as self-assembled loops at elevated temperatures. Post-irradiation Burgers vector analysis via g•b method on loops and electron tomography reveals that <001> preponderance is observable in all irradiated Fe-Cr samples at elevated temperature, resulting from stronger elastic energy originating from <001> edge.

Li, Yao [University of Tennessee (UT)]↗
DOE OSTI2025

Anisotropic structure and optical engineering of strontium titanate and zirconia responding to sequential hydrogen and helium irradiation

Unraveling the correlation between strain engineering with anisotropic optical properties via nanoscale defects gradually evolved into a strategy for fundamental studies and technological applications, yet it remains understudied in functional complex oxides compared to metals and semiconductors. Here, the methodology of strain engineering for the determination of the lattice parameters, parallel/normal to the sample surface, in the individual layers of single-crystalline superlattices is derived, which is based on analysis of high-angle X-ray diffraction measurements in combination with diffraction reciprocal space mapping. With modeling that takes into account the effect of elastic properties, two elastically anisotropic materials, SrTiO 3 and ZrO 2 , have been compared in terms of defect-induced elastic strain caused by individual and sequential H + and He 2+ irradiation. The anisotropic lattice swelling with corresponding refractive index, and obstructive behavior of elastic strain recovery are demonstrated in SrTiO 3 , while approaching strain behaviors accompanied by isotropic refractive index distribution in both orientations are confirmed in ZrO 2 . Under sequential He 2+ /H + irradiation, pre-existing He-vacancy complexes acted as vacancy traps, preferentially capturing H + clusters to induce lattice distortion and enhance absorption. Nanohardness increments (ΔH) calculated by the DBH model matched nanoindentation results, confirming that sequential irradiation generated higher indentation yield stress than individual irradiations.

Anisotropic expansion↗
DOE OSTI2025

Bayesian SegNet for Semantic Segmentation with Improved Interpretation of Microstructural Evolution During Irradiation of Materials

Understanding the relationship between the evolution of microstructures of irradiated LiAlO2pellets and tritium diffusion, retention and release could improve predictions of tritium performance. Given expert-labeled segmented images of irradiated and unirradiated pellets, we trained Deep Convolutional Neural Networks to segment images into defect, grain, and boundary classes. Qualitative microstructural information was calculated from these segmented images to facilitate the comparison of unirradiated and irradiated pellets. We tested modifications to improve the sensitivity of the model, including incorporating meta-data into the model and utilizing uncertainty quantification. The predicted segmentation was similar to the expert-labeled segmentation for most methods of microstructural qualification, including pixel proportion, defect area, and defect density. Overall, the high performance metrics for the best models for both irradiated and unirradiated images shows that utilizing neural network models is a viable alternative to expert-labeled images.

Oostrom, Marjolein T.↗