Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Site distribution and aliasing effects in the inversion for load coefficients and geocenter motion from GPS data

Precise GPS measurements of elastic relative site displacements due to surface mass loading offer important constraints on global surface mass transport. We investigate effects of site distribution and aliasing by higher- degree (n ≥ 2) loading terms on inversion of GPS data for n = 1 load coefficients and geocenter motion. Covariance and simulation analyses are conducted to assess the sensitivity of the inversion to aliasing and mismodeling errors and possible uncertainties in the n = 1 load coefficient determination. We found that the use of center-of-figure approximation in the inverse formulation could cause 10– 15% errors in the inverted load coefficients. n = 1 load estimates may be contaminated significantly by unknown higher-degree terms, depending on the load scenario and the GPS site distribution. The uncertainty in n = 1 zonal load estimate is at the level of 80–95% for two load scenarios.

Webb, Frank H.↗
NASA NTRSDate not supplied

Alternate Inversion Paradigm for Spectroheliogram Data

Over the past five years, new methods to reconstruct spectrally pure maps of the Sun from spectroheliogram data have emerged, essentially unlocking this long-abandoned method of obtaining both spatial and spectral information over a large field of view simultaneously. The original inversion method determined the plasma’s emission measure distribution as a function of temperature at every spatial location in the field of view. To complete this inversion, a response matrix had to be created mapping the emission measure in different (temperature, space) bins to detector, requiring assumptions on the thermal and ionization equilibrium and abundance state of the plasma. We have since derived a new method of the inversion that does not require these atomic assumptions to be made. Instead, we use only the different locations of spectral lines from the same ion species and the possible ratios of those single-species spectral lines, removing the need for a priori knowledge on the state of the emitting plasma. In this presentation, we demonstrate this method using observed data from the Marshall Grazing Incidence X-ray Spectrometer (MaGIXS) and simulated data from the EUV CME and Coronal Connectivity Observatory (ECCCO) investigation.

Amy Winebarger↗
NASA NTRS2023

Optimal Estimation Inversion of Ionospheric Electron Density from GNSS-POD Limb Measurements: Part II-Validation and Comparison Using NmF2 and hmF2

A growing number of SmallSat/CubeSat constellations with high-rate (50–100 Hz) global navigation satellite system radio occultations (GNSS-RO) as well as low-rate (1 Hz) precise orbit determination (GNSS-POD) limb-viewing capabilities provide unprecedented spatial and temporal sampling rates for ionospheric studies. In the F-region electron density (N 𝑒 ) retrieval process, instead of the conventional onion-peeling (OP) inversion, an optimal estimation (OE) inversion technique was recently developed using total electron content measurements acquired by GNSS-POD link. The new technique is applied to data acquired from the COSMIC-1, COSMIC-2, and Spire constellations. Although both OE and OP techniques use the Abel weighting function in N 𝑒 inversion, OE significantly differs in its performance, especially in the lower F- and E-regions. In this work, we evaluate and compare newly derived data sets using F2 peak properties with other space-based and ground-based observations. We determine the F2 peak N 𝑒 (NmF2) and its altitude (hmF2), and compare them with the OP-retrieved values. Good agreement is observed between the two techniques for both NmF2 and hmF2. In addition, we also utilize autoscaled F2 peak measurements from a number of worldwide Digisonde stations (∼30). The diurnal sensitivity and latitudinal variability of the F2 peak between the two techniques are carefully studied at these locations. Good agreement is observed between OE-retrieved NmF2 and Digisonde-measured NmF2. However, significant differences appear between OE-retrieved hmF2 and Digisonde-measured hmF2. During the daytime, Digisonde-measured hmF2 remains ∼25–45 km below the OE-retrieved hmF2, especially at mid and high latitudes. We also incorporate F-region N 𝑒 measurements from two incoherent scatter radar observations at high latitudes, located in the North American (Millstone Hill) and European (EISCAT at Tromso) sectors. The radar measurements show good agreement with OE-retrieved values. Although there are several possible sources of error in the ionogram-derived N 𝑒 profiles, our further analysis on F1 and F2 layers indicates that the low Digisonde hmF2 is caused by the autoscaled method, which tends to detect a height systematically below the F2 peak when the F1 layer is present.

GNSS radio occultation↗
NASA NTRS1999

Mesospheric Temperature Inversion Layers: Recent Observations from UARS ISAMS and MLS

This paper presents an observational study of the mesospheric temperature inversion layer with Upper Atmosphere Research Satellite (UARS) Improved Stratospheric and Mesospheric Sounder (ISAMS) and Microwave Limb Sounder (MLS). The satellite data show that the temperature inversion layer can be generated from deep penetration of planetary waves in the mesosphere.

mesospheric temperature inversion layers UARS ISAM↗
NASA NTRS2012

Collective Evidence for Inverse Compton Emission from External Photons in High-Power Blazars

We present the first collective evidence that Fermi-detected jets of high kinetic power (L(sub kin)) are dominated by inverse Compton emission from upscattered external photons. Using a sample with a broad range in orientation angle, including radio galaxies and blazars, we find that very high power sources (L(sub kin) > 10(exp 45.5) erg/s) show a significant increase in the ratio of inverse Compton to synchrotron power (Compton dominance) with decreasing orientation angle, as measured by the radio core dominance and confirmed by the distribution of superluminal speeds. This increase is consistent with beaming expectations for external Compton (EC) emission, but not for synchrotron self Compton (SSC) emission. For the lowest power jets (L(sub kin) < 10(exp 43.5) erg /s), no trend between Compton and radio core dominance is found, consistent with SSC. Importantly, the EC trend is not seen for moderately high power flat spectrum radio quasars with strong external photon fields. Coupled with the evidence that jet power is linked to the jet speed, this finding suggests that external photon fields become the dominant source of seed photons in the jet comoving frame only for the faster and therefore more powerful jets.

INVERSE↗
NASA NTRS2021

Constrained Inversion of a Microwave Snowpack Emission Model Using Dictionary Matching: Applications for GPM Satellite

This article presents a new algorithmic framework for multilayer inversion of the dense media radiative transfer (DMRT) equations of snowpack emission, with particular emphasis on the role of high-frequency microwave channels above 60 GHz. The approach relies on dictionary matching and locally constrained least squares. The results demonstrate that the algorithm can invert the DMRT model and retrieve depth, density, and grain size of a single-layer snowpack when dependencies of density and grain size on depth are properly accounted for. However, as the number of layers increases, the sensitivity of the inversion to observation noise grows markedly. Using observations, over the Great Plains in the United States, from the microwave imager onboard the global precipitation measurement (GPM, 10-166 GHz) core satellite, the initial results demonstrate that under a clear-sky condition and no vegetation canopy, the algorithm is capable to retrieve the snow depth and water equivalent of seasonal snow with a mean absolute error (MAE) of less than 0.15 m--when compared to the high-resolution analysis data from the SNOw Data Assimilation System (SNODAS).

Snow↗
NASA NTRSDate not supplied

Progress on Inverse Estimation Technique of Non-Linear Pitch Damping Coefficient Curves Using Free-Flight CFD Generated Trajectories

Characterization of entry vehicle pitch damping coefficient curves is crucial to ensure appropriate re-entry and overall mission success. The pitch damping coefficient (C_(m_q )+C_(m_α ̇ )) is used to encapsulate the oscillatory growth or decay of a body during a trajectory. The inverse estimation technique utilizes an existing Free-Flight CFD (FF-CFD) dataset and wraps a reconstruction algorithm in an optimizer. The reconstruction integrates the planar equations of motion derived by Schoenenberger, Queen [1] using Python’s scipy.integrate.solve_ivp. The optimizer’s objective function is the normalized 𝐿2 residual of the angle of attack peaks between the reconstructed trajectory and the original data produced with FF-CFD. Inclusion of the peak times in this residual calculation allows for simultaneous optimization of the pitch moment coefficient, C_(m_α ). This residual equation is shown below in Eq. 1. The optimizer scipy.optimize.minimize was used with the gradient-based Powell method for the analysis presented, however the differential evolution method was investigated as means of comparison, and was found to produce marginally lower residual values with prohibitively longer run times. Further, the pitch damping curve is found by fitting a cubic interpolation function to a set of (α, (C_(m_q )+C_(m_α ̇ ))) control points, where the α points are held constant and the (C_(m_q )+C_(m_α ̇ )) values are the optimized parameters. The pitch moment curve uses a linear interpolation between the minimum and maximum α in the dataset. FF-CFD generated trajectories using the Dragonfly capsule geometry with the Genesis ballistic range model parameters were simulated and used for this analysis. These FF-CFD trajectories simulate planar motion, as restricted by the reconstructing the equations of motion, of three different cases: 1-DoF (free-to-pitch), 2-DoF (free-to-pitch and heave), and 3-DoF (free-to-pitch, heave, and decelerate). Pitch damping coefficient curves generated using this inverse estimation curve technique with FF-CFD 1-DoF Dragonfly data are found in Fig. 1. Preliminary results reconstructing ballistic range shots using these FF-CFD derived predictions of the pitch damping curve (Fig. 1) are shown in Fig. 2. It should be noted that the ballistic range shot used a Genesis model whereas the FF-CFD data used a Dragonfly geometry, however these geometries are similar.

entry↗
NASA NTRS2023

Equivalent Area Targets for Inverse Design Optimization With Changing Low-Boom Cruise Conditions

This paper provides theoretical and numerical justifications for inverse design optimization of reversed equivalent area (A e,r ) of low-boom supersonic aircraft when the cruise condition changes during the optimization iterations. A modified linear theory for steady flow around a supersonic projectile is used to establish the accuracy of A e,r -based body-of-revolution approximation of a low-boom supersonic aircraft for undertrack sonic boom analysis using computational fluid dynamics off-body pressure. As a result, designing a low-boom shape of the off-body pressure at three body lengths below the aircraft is equivalent to designing a low-boom A e,r shape. A Bezier curve with eight control points is used to define an A e,r target for inverse design optimization of A e,r of a supersonic aircraft. To make an A e,r target matchable by a low-boom supersonic aircraft, the A e,r target must have the minimal perceived level of decibels (PLdB) for sonic boom and satisfy two constraints defined by the cruise condition, effective length, and two nondimensional parameters. Numerical results are used to verify that, for different cruise conditions, all optimized A e,r targets with PLdB below 70 can be approximately generated by scaling one of them if the targets have the same nondimensional parameters and approximately the same effective length.

multidisciplinary optimization↗
NASA NTRS2023

Optimal Estimation Inversion of Ionospheric Electron Density from GNSS-POD Limb Measurements: Part I-Algorithm and Morphology

GNSS-LEO radio links from Precise Orbital Determination (POD) and Radio Occultation (RO) antennas have been used increasingly in characterizing the global 3D distribution and variability of ionospheric electron density (N e ). In this study, we developed an optimal estimation (OE) method to retrieve N e profiles from the slant total electron content (hTEC) measurements acquired by the GNSS-POD links at negative elevation angles (ε < 0°). Although both OE and onion-peeling (OP) methods use the Abel weighting function in the N e inversion, they are significantly different in terms of performance in the lower ionosphere. The new OE results can overcome the large N e oscillations, sometimes negative values, seen in the OP retrievals in the E-region ionosphere. In the companion paper in this Special Issue, the HmF2 and NmF2 from the OE retrieval are validated against ground-based ionosondes and radar observations, showing generally good agreements in NmF2 from all sites. Nighttime hmF2 measurements tend to agree better than the daytime when the ionosonde heights tend to be slightly lower. The OE algorithm has been applied to all GNSS-POD data acquired from the COSMIC-1 (2006–2019), COSMIC-2 (2019–present), and Spire (2019–present) constellations, showing a consistent ionospheric N e morphology. The unprecedented spatiotemporal sampling of the ionosphere from these constellations now allows a detailed analysis of the frequency–wavenumber spectra for the N e variability at different heights. In the lower ionosphere (~150 km), we found significant spectral power in DE1, DW6, DW4, SW5, and SE4 wave components, in addition to well-known DW1, SW2, and DE3 waves. In the upper ionosphere (~450 km), additional wave components are still present, including DE4, DW4, DW6, SE4, and SW4. The co-existence of eastward- and westward-propagating wave4 components implies the presence of a stationary wave4 (SPW4), as suggested by other earlier studies. Further improvements to the OE method are proposed, including a tomographic inversion technique that leverages the asymmetric sampling about the tangent point associated with GNSS-LEO links.

GNSS constellation↗
NASA NTRS1968

Clouds and the inversion problem.

Limb darkening inversion analyzed by earth atmosphere model with imbedded cloud, discussing radiances inversion for various cloud covers and heights

House, F. B.↗
NASA NTRS1969

Dewpoint temperature inversions analyzed

Dewpoint temperature inversion, with regard to other simultaneous meteorological conditions, was examined to establish the influence of meteorological variables on the variation of dewpoint temperature with height. This report covers instrumentation and available data, all the climatological features of dewpoint inversions, and specific special cases.

Ashby, W. C.↗
NASA NTRS1969

Towards an optimal inversion method for remote atmospheric sensing

The inference of atmospheric structure from satellite radiometric observations requires an inversion algorithm. A variety of techniques was spawned to meet these demands. One class, the nonlinear inversion methods, copes with the problem of data noise. Unlike linear techniques which require a priori data smoothing, the nonlinear method can be applied directly to raw data. The algorithm discriminates the noise input by resolving the inferences into two types of solution, associating the real roots with atmospheric structure while ascribing the imaginary roots to noise.

King, J. I. F.↗
NASA NTRS1972

Population inversion calculations using near resonant charge exchange as a pumping mechanism

Near resonance charge exchange between ions of a large ionization potential gas such as helium or neon and vapors of metals such as zinc, cadmium, selenium, or tellurium has produced laser action in the metal ion gas. The possibility of obtaining population inversions in near resonant charge exchange systems (Xe-Ca, Xe-Mg, Xe-Sr, Xe-Ba, Ar-Mg, N-Ca) was investigated. The analysis is an initial value problem that utilizes rate equations for the densities of relevant levels of the laser gas (Ca, Ba, Mg, or Sr) and an electron energy equation. Electron excitation rates are calculated using the Bohr-Thomson approximation for the cross section. Approximations to experimental values of the electron ionization cross section and the ion-atom charge exchange cross section are used. Preliminary results have been obtained for the Ca-Xe system and show that it is possible to obtain gains greater than 10 to the 14th power/m with inversion times up to 8x10 to the minus 7th power second. A possible charge exchange laser system using a MPD arc plasma accelerator is also described.

Chubb, D. L.↗
NASA NTRS1971

Photovoltage inversion effect and its application to semiconductor surface studies: CdS.

Experimental results on the surface states of the basal plane of CdS are presented and discussed in the light of a model of the photovoltage inversion effect. It is found that the surface states associated with this effect are in poor communication with the bulk and under normal conditions may require long periods of time to reach equilibrium. A combination of photovoltage inversion, photovoltage quenching, and photovoltage spectroscopy is believed to constitute a very effective tool for the study of surfaces of wide energy gap semiconductors.

Lagowski, J.↗
NASA NTRS1972

Subsonic, transonic, and supersonic nozzle flow by the inverse technique.

The inverse technique is used to obtain a mathematically and physically consistent solution of the flowfield in a nozzle from the mass generation surface through the supersonic region. The inverse method employs an assumed centerline function which is of the Cauchy type in that the values and the derivatives of the function are known. Since the Cauchy boundary conditions can give rise to numerical instabilities, the governing gasdynamic equations for rotational steady flow were transformed into a form which puts the geometry into a rectangular shape, and which spaces the network of interior points more finely in regions of the greatest gradients of the dependent variables. For arbitrarily specified centerline data, the solution of the governing flow equations may not exist, and if it does it may not depend continuously on the data.

Norton, D. J.↗