Search NASA⌕ Search

SEARCH · Search NASA

Results for “Multifunctional Applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Advanced Frost Sensor for HVAC Applications

Frost is a common problem in heating, ventilation, and air conditioning (HVAC) systems that can degrade their efficiencies, leading to excessive electricity consumption. Appropriate defrosting is therefore essential for heat pumps and refrigeration systems. However, these systems typically run the defrost cycle based on a predetermined time interval, a method that does not accurately identify the amount of frost and thus consume excessive electricity. To substantially improve defrosting initiation and termination, this paper describes development of a smart sensor based on a capacitive sensing technique that can quantify frost accumulation and difference between frost, ice, and water. The reported sensor adopts interdigitated comb electrodes and can be updated to a potential multifunctional sensor array for the enhancing identification of frost, ice, and water with the integrated measurement of surface temperature, frost capacitance, and resistance. The proposed frost sensor is potentially expected to have widespread applications in HVAC systems, including heat pumps, refrigerators, and commercial refrigeration systems.

Gao, Zhiming↗
DOE OSTI2024

Tough and circular glass fiber composites via a tailored dynamic boronic ester interface

Glass fiber reinforced polymer (GFRP) composites are valued for their strength and cost-effectiveness. However, traditional GFRPs often face challenges for end-of-life recycling due to their non-depolymerizable thermoset matrices, and long-term performance due to inadequate interfacial adhesion, which can lead to fiber–matrix delamination. Here, in this work, we have designed dynamic fiber–matrix interfaces to allow tough and closed-loop recyclable GFRPs by utilizing a vitrimer, derived from upcycled polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS) with boronic ester (S-Bpin) and amine-based diol crosslinker. The boronic ester groups in S-Bpin form dynamic covalent bonds with the naturally present hydroxyl groups on the unsized GF surface, which eliminates the need for fiber sizing and enables facile closed-loop recyclability of both the fibers and the vitrimer matrix. The resulting strong fiber–matrix interface, depicted by the Raman mapping, leads to a 552% increase in-plane shear toughness (6.2 ± 0.3 MJ m -3 ) and 27% ultimate tensile strength (361 ± 89.2 MPa) compared to those of the conventional epoxy-based matrix (0.95 ± 0.05 MJ m -3 and 264 ± 59.7 MPa, respectively). The network rearrangement through dynamic boronic ester exchange enables fast thermoformability and repairability of micro-cracks at elevated temperatures. Additionally, both the matrix and composite demonstrate strong adhesion to various surfaces including steel and glasses exhibiting ≥6 MPa lap shear strength, which expands their suitability for diverse industrial applications. The readily created dynamic interface between boronic ester functionalized vitrimer and neat GFs presents a promising strategy for developing closed-loop recyclable, multifunctional structural materials, offering a sustainable alternative to non-recyclable thermoset GFRPs and contributes to a circular economy in composite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of Antimicrobial PLA Composites for Fused Filament Fabrication

In addition to possessing the desirable properties of being a biodegradable and biocompatible polymer fabricated from renewable resources, poly (lactic acid) (PLA) has useful mechanical and thermal attributes that has enabled it to be one of the most widely-used plastics for medicine, manufacturing, and agriculture. Yet, PLA composites have not been heavily explored for use in 3D-printing applications, and the range of feasible materials for the technology is limited, which inhibits its potential growth and industry adoption. In this study, tunable, multifunctional antimicrobial PLA composite filaments for 3D-printing have been fabricated and tested via chemical, thermal, mechanical, and antimicrobial experiments. Thermally stable antimicrobial ceramics, ZnO and TiO2, were used as fillers up to 30 wt%, and poly (ethylene glycol) (PEG) was used as a plasticizer to tune the physical material properties. Results demonstrate that the PLA composite filaments exhibit the thermal phase behaviors and thermal stability suitable for 3D-printing. Additionally, PEG can be used to tune the mechanical properties while not affecting the antimicrobial efficacy that ZnO and TiO2 imbue.

TiO2↗
NASA NTRS2005

Nanomaterials Work at NASA-Johnson Space Center

Nanomaterials activities at NASA-Johnson Space Center focus on single wall carbon nanotube production, characterization and their applications for aerospace. Nanotubes are produced by arc and laser methods and the growth process is monitored by in-situ diagnostics using time resolved passive emission and laser induced fluorescence of the active species. Parametric study of both these processes are conducted to monitor the effect of production parameters including temperature, buffer gas, flow rate, pressure, laser fluence and arc current. Characterization of the nanotube material is performed using the NASA-JSC protocol developed by combining analytical techniques of SEM, TEM, UV-VIS-NIR absorption, Raman, and TGA. Efforts at JSC over the past five years in composites have centered on structural polymernanotube systems. Recent activities broadened this focus to multifunctional materials, supercapacitors, fuel cells, regenerable CO2 absorbers, electromagnetic shielding, radiation dosimetry and thermal management systems of interest for human space flight. Preliminary tests indicate improvement of performance in most of these applications because of the large surface area as well as high conductivity exhibited by SWCNTs.

Arepalli, Sivaram↗
DOE OSTI2020

High Speed In-situ X-ray Imaging of 3D Freeze Printing of Aerogels

3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.

36 MATERIALS SCIENCE↗
NASA NTRS2005

Mechanical and Electrical Properties of a Polyimide Film Significantly Enhanced by the Addition of Single-Wall Carbon Nanotubes

Single-wall carbon nanotubes have been shown to possess a combination of outstanding mechanical, electrical, and thermal properties. The use of carbon nanotubes as an additive to improve the mechanical properties of polymers and/or enhance their thermal and electrical conductivity has been a topic of intense interest. Nanotube-modified polymeric materials could find a variety of applications in NASA missions including large-area antennas, solar arrays, and solar sails; radiation shielding materials for vehicles, habitats, and extravehicular activity suits; and multifunctional materials for vehicle structures and habitats. Use of these revolutionary materials could reduce vehicle weight significantly and improve vehicle performance and capabilities.

Meador, Michael A.↗
NASA NTRS2006

Event Detection in Aerospace Systems using Centralized Sensor Networks: A Comparative Study of Several Methodologies

Recent advances in micro electromechanical systems technology, digital electronics, and wireless communications have enabled development of low-cost, low-power, multifunctional miniature smart sensors. These sensors can be deployed throughout a region in an aerospace vehicle to build a network for measurement, detection and surveillance applications. Event detection using such centralized sensor networks is often regarded as one of the most promising health management technologies in aerospace applications where timely detection of local anomalies has a great impact on the safety of the mission. In this paper, we propose to conduct a qualitative comparison of several local event detection algorithms for centralized redundant sensor networks. The algorithms are compared with respect to their ability to locate and evaluate an event in the presence of noise and sensor failures for various node geometries and densities.

Mehr, Ali Farhang↗
NASA NTRS2008

Hydrogen Research for Spaceport and Space-Based Applications: Hydrogen Sensors and Systems

The activities presented are a broad based approach to advancing key hydrogen related technologies in areas such as fuel cells, hydrogen production, and distributed sensors for hydrogen-leak detection, laser instrumentation for hydrogen-leak detection, and cryogenic transport and storage. Presented are the results from research projects, education and outreach activities, system and trade studies. The work will aid in advancing the state-of-the-art for several critical technologies related to the implementation of a hydrogen infrastructure. Activities conducted are relevant to a number of propulsion and power systems for terrestrial, aeronautics and aerospace applications. Sensor systems research was focused on hydrogen leak detection and smart sensors with adaptive feedback control for fuel cells. The goal was to integrate multifunction smart sensors, low-power high-efficiency wireless circuits, energy harvesting devices, and power management circuits in one module. Activities were focused on testing and demonstrating sensors in a realistic environment while also bringing them closer to production and commercial viability for eventual use in the actual operating environment.

Anderson, Tim↗
NASA NTRS2005

Multifunctional Deployment Hinges Rigidified by Ultraviolet

Multifunctional hinges have been developed for deploying and electrically connecting panels comprising planar arrays of thin-film solar photovoltaic cells. In the original intended application of these hinges, the panels would be facets of a 32-sided (and approximately spherical) polyhedral microsatellite (see figure), denoted a PowerSphere, that would be delivered to orbit in a compact folded configuration, then deployed by expansion of gas in inflation bladders. Once deployment was complete, the hinges would be rigidified to provide structural connections that would hold the panels in their assigned relative positions without backlash. Such hinges could also be used on Earth for electrically connecting and structurally supporting solar panels that are similarly shipped in compact form and deployed at their destinations. As shown in section A-A in the figure, a hinge of this type is partly integrated with an inflation bladder and partly integrated with the frame of a solar panel. During assembly of the hinge, strip extensions from a flexible circuit harness on the bladder are connected to corresponding thin-film conductors on the solar panel by use of laser welding and wrap-around contacts. The main structural component of the hinge is a layer of glass fiber impregnated with an ultraviolet-curable resin. After deployment, exposure to ultraviolet light from the Sun cures the resin, thereby rigidifying the hinge.

Kerslake, Thomas W.↗
DOE OSTI2021

A universal and facile approach for building multifunctional conjugated polymers for human-integrated electronics

Polymer semiconductors have shown distinct promise for the development of human- integrated electronics, owing to their solution processability and mechanical softness. However, numerous functional properties required for this application domain face synthetic challenges to be imparted onto conjugated polymers and thus combined with efficient charge- transport property. Here, we develop a “click-to-polymer” (CLIP) synthesis strategy for conjugated polymers, which uses a click reaction for the facile and versatile attachment of diverse types of functional units to a pre-synthesized conjugated-polymer precursor. With four types of functional groups, we show that functionalized polymers from this CLIP method can still retain good charge-carrier mobility. Here, we take two realized polymers to showcase the photo-patternable property and biochemical sensing function, both of which advance the state of the art of realizing these two types of functions on conjugated polymers. We expect the expanded use of this synthesis approach can largely enrich the functional properties from conjugated polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Compression Response of Silicone-Based Composites with Integrated Multifunctional Fillers

Polydimethylsiloxane (PDMS) is known for its exceptional mechanical properties, chemical stability, and flexibility. Recent advancements have focused on developing functional PDMS composites by integrating various functional fillers, including polymers, ceramics, and metals, for advanced applications such as electronics, medical devices, and aerospace. Consequently, there is a growing need to investigate PDMS composites to achieve higher filler loadings offering enhanced mechanical performance. This study addresses this need by utilizing the high molecular weight (MW) PDMS resin we have developed, offering its high elongation capacity of up to >6500%. We incorporated boron (B), hollow glass microballoons (HGMs), and tungsten-coated hollow glass microballoons (WHGMs) into the developed high MW PDMS. The resulting composites demonstrated excellent elastic properties and significant compression resilience (35–80%) and elastic modulus (1.28–10.15 MPa) at high filler loadings (~60 vol.%). Specifically, B/PDMS composites achieved up to 67.6 vol.% of B, HGM/PDMS composites held up to 68.6 vol.% of HGM, and WHGM/PDMS composites incorporated up to 54.0 vol.% of WHGM. These findings highlight the potential of high MW PDMS for developing high-performance PDMS composites suitable for advanced applications such as aerospace, automotive, and medical devices.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Development of Advanced Spacecraft Thermal Subsystems

This presentation discusses ground based proof of concept hardware under development at NASA GSFC to address high heat flux thermal management in silicon substrates and embedded thermal management systems. The goal is to develop proof of concept hardware for space flight validation. The space flight hardware will provide gravity insensitive thermal management for electronics applications such as transmit/receive modules that are severely limited by thermal concerns.

Thermal Control Multifunctional Hardware↗
NASA NTRS2006

Carbon Nanotube Activities at NASA-Johnson Space Center

Research activities on carbon nanotubes at NASA-Johnson Space Center include production, purification, characterization and their applications for human space flight. In-situ diagnostics during nanotube production by laser oven process include collection of spatial and temporal data of passive emission and laser induced fluorescence from C2, C3 and Nickel atoms in the plume. Details of the results from the "parametric study" of the pulsed laser ablation process indicate the effect of production parameters including temperature, buffer gas, flow rate, pressure, and laser fluence. Improvement of the purity by a variety of steps in the purification process is monitored by characterization techniques including SEM, TEM, Raman, UV-VIS-NIR and TGA. A recently established NASA-JSC protocol for SWCNT characterization is undergoing revision with feedback from nanotube community. Efforts at JSC over the past five years in composites have centered on structural polymednanotube systems. Recent activities broadened this focus to multifunctional materials, supercapacitors, fuel cells, regenerable CO2 absorbers, electromagnetic shielding, radiation dosimetry and thermal management systems of interest for human space flight. Preliminary tests indicate improvement of performance in most of these applications because of the large surface area as well as high electrical and thermal conductivity exhibited by SWCNTs.

Arepalli, Sivaram↗
DOE OSTI2020

Catalytic Porphyrin Framework Compounds

Porphyrins are frequently observed in nature and play a vital role in many biological functions, including light-harvesting, oxygen transport, and catalytic transformations. The rigid, robust, and multifunctional features of porphyrins enable the construction of framework compounds such as metal–organic frameworks (MOFs) and covalent organic frameworks (COFs) for use in several important applications. This short review here summarizes the types of porphyrin building blocks with varying connectivity, their assembly into framework compounds, and key structural factors governing porphyrin ligand design. Furthermore, we highlight emerging catalytic applications of these porphyrin framework compounds as Lewis acid catalysts, oxidation catalysts, photocatalysts, and electrocatalysts. Together, this review supplies a timely update on porphyrin ligand design and framework compound synthesis and guides the future development of porphyrin framework compounds with diverse functionalities for efficient catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2004

Nanotube Activities at NASA-Johnson Space Center

Nanotube activities at NASA-Johnson Space Center include production, purification, characterization as well as applications of single wall carbon nanotubes (SWCNTs). A parametric study of the pulsed laser ablation process is recently completed to monitor the effect of production parameters including temperature, buffer gas, flow rate, pressure, and laser fluence. Enhancement of production is achieved by rastering the graphite target and by increasing the target surface temperature with a cw laser. In-situ diagnostics during production included time resolved passive emission and laser induced fluorescence from the plume. The improvement of the purity by a variety of steps in the purification process is monitored by characterization techniques including SEM, TEM, Raman, UV-VIS-NIR and TGA. A recently established NASA-JSC protocol for SWCNT characterization is undergoing revision with feedback from nanotube community. Efforts at JSC over the past five years in composites have centered on structural polymer/nanotube systems. Recent activities broadened this focus to multifunctional materials, supercapacitors, fuel cells, regenerable CO2 absorbers, electromagnetic shielding, radiation dosimetry and thermal management systems of interest for human space flight. Preliminary tests indicate improvement of performance in most of these applications because of the large Surface area as well as high electrical and thermal conductivity exhibited by SWCNTs. Comparison with existing technologies and possible future improvements in the SWCNT materials sill be presented.

Arepalli, Sivaram↗
NASA NTRS1986

A multifunction recognition operator for telerobotic vision

Research on developing an operator capable of performing the various subtasks required of a telerobot's vision sensor is reported. The operator uses a goal-driven matching technique which is an application of a linear programming method that readily adapts to the elastic template matching approach to pattern recognition. Four applications of the operator are discussed: (1) three-space location of an isolated object; (2) shape determination of isolated planar figures; (3) image compression/restoration; and (4) shape decomposition.

Goode, P. W., IV↗
DOE OSTI2022

In situ imaging of three dimensional freeze printing process using rapid x-ray synchrotron radiography

Three dimensional freeze printing (3DFP) combines the advantages of freeze casting and additive manufacturing to fabricate multifunctional aerogels. Freeze casting is a cost-effective, efficient, and versatile method capable of fabricating micro-scale porous structures inside the aerogels for many different applications. The 3DFP provided the capability of fabricating highly customized geometries with controlled microporous structures as well. However, there are still many unexplained phenomena and features because of the complexity of post-processes and indirect observation methods. This study demonstrates the design and construction of the in situ imaging systems, which use the x-ray synchrotron radiography to observe freeze casting and 3DFP processes. With the advantages provided by the in situ x-ray imaging techniques, the ice crystal growth with its unique lamellar structures can be observed during the freeze casting process. Here, the movement of freeze front, material deposition, and growth of ice crystals can also be visualized during the inkjet-based 3DFP process.

3D printing↗