Search NASA⌕ Search

SEARCH · Search NASA

Results for “Particle sizing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Crack‐Free Single‐Crystalline LiNiO 2 for High Energy Density All‐Solid‐State Batteries

Abstract Single‐crystalline layered oxide (LiNi 1‐ x ‐ y Mn x Co y O 2 ) cathodes have been found to exhibit exceptional electrochemical properties when coupled with various inorganic solid electrolytes (ISEs) in all‐solid‐state batteries (ASSBs). Their advantages stem from the robust morphological integrity with the absence of grain boundaries and the high electrochemical oxidative stability. Here, ASSBs featuring single‐crystalline LiNiO 2 (LNO) with the highest Ni content are reported, offering a high theoretical specific capacity of 275 mAh g ‐1 alongside a high average discharge voltage (3.7 V vs Li + /Li). Through a careful investigation, it is demonstrated that micron‐sized single‐crystalline LNO (µSC‐LNO) composite cathodes with a halide ISE exhibit a high initial discharge capacity of 205 mAh g ‐1 with an outstanding cycle performance over 200 cycles in room‐temperature ASSBs. The significance of engineering parameters is emphasized, such as particle size and specific density, in promoting a homogeneous and fast Li + transport within the composite cathodes. Furthermore, the formation of undesirable interphase between the halide ISE in the cathode and sulfide ISE separator is elucidated, which may be a critical factor impeding long‐term cyclability of ASSBs. This work provides insights into the design of composite cathodes for high‐energy‐density ASSBs.

Chemistry↗
DOE OSTI2024

An Investigation of Oxides of Tantalum Produced by Pulsed Laser Ablation and Continuous Wave Laser Heating

Recent progress has seen multiple Ta 2 O 5 polymorphs generated by different synthesis techniques. However, discrepancies arise when these polymorphs are produced in widely varying thermodynamic conditions and characterized using different techniques. This work aimed to characterize and compare Ta 2 O 5 particles formed at high and low temperatures using nanosecond pulsed laser ablation (PLA) and continuous wave (CW) laser heating of a local area of tantalum in either air or an 18 O 2 atmosphere. Scanning electron microscopy (SEM) and Raman spectroscopy of the micrometer-sized particles generated by PLA were consistent with either a localized amorphous Ta 2 O 5 phase or a similar, but not identical, crystalline β-Ta 2 O 5 phase. The Raman spectrum of the material formed at the point of CW laser impingement was in good agreement with the previously established ceramic “H-Ta 2 O 5 ” phase. TEM and electron diffraction analysis of these particles indicated the phase structure matched an oxygen-vacated superstructure of monoclinic H-Ta 2 O 5 . Further from the point of laser impingement, CW heating produced particles with a Raman spectrum that matched β-Ta 2 O 5 . We confirmed that the high-temperature ceramic phase characterized in previous work by Raman spectroscopy was the same monoclinic phase characterized in different work by TEM and could be produced by direct laser heating of metal in air.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Introducing dusty plasma particle growth of nanospherical titanium dioxide

In dusty plasma environments, spontaneous growth of nanoparticles from reactive gases has been extensively studied for over three decades, primarily focusing on hydrocarbons and silicate particles. Here, we introduce the growth of titanium dioxide, a wide bandgap semiconductor, as dusty plasma nanoparticles. The resultant particles exhibited a spherical morphology and reached a maximum monodisperse radius of 235 ± 20 nm after growing for 70 s. The particle grew linearly, and the growth displayed a cyclic behavior; that is, upon reaching their maximum radius, the largest particles fell out of the plasma, and the next growth cycle immediately followed. The particles were collected after being grown for different amounts of time and imaged using scanning electron microscopy. Further characterization was carried out using energy dispersive x-ray spectroscopy, x-ray diffraction, and Raman spectroscopy to elucidate the chemical composition and crystalline properties of the maximally sized particles. Initially, the as-grown particles exhibited an amorphous structure after 70 s. However, annealing treatments at temperatures of 400 and 800 °C induced crystallization, yielding anatase and rutile phases, respectively. Annealing at 600 °C resulted in a mixed phase of anatase and rutile. These findings open avenues for a rapid and controlled growth of titanium dioxide via dusty plasma.

Physics↗
DOE OSTI2024

Optical constants measurements of liquids for modeling aerosolized threats

Spectroscopic identification of aerosolized chemical threats is challenging due to the complex nature of the photon/particle interaction, as well as the diversity of possible particle sizes, morphologies, and compositions. Constructing a database of laboratory - measured transmittance spectra that covers each permutation is not practical. However, calculation of the spectra using the measured optical constants as a function of wavenumber, n(?) and k(?), for each of the liquids and/or solids composing the aerosol particles provides a viable alternative. These synthetic spectra (vis-à-vis laboratory-measured spectra) can be used to identify chemicals of interest and subtract out background interferents in field measurements. Using a well-established multiple pathlength approach, we measure the optical constants n/k for liquids that may be found as chemical species of interest or common background interferents aerosolized in plumes. These measurements are also used to generate several test case aerosol synthetic spectra.

Lockwood, Schuyler↗
DOE OSTI2025

Properties of different LLM-105 preparations

LLM-105 (2,6-diamino-3,5-dinitropyrazine-1-oxide) has been prepared at several different size quantities (~10–70 Kg) and not subjected to further purification, such as recrystallization. Chemical and physical properties were compared—small-scale safety testing (impact, friction, ESD), thermal (chemical reactivity, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), one-dimensional time-to-explosion (ODTX)), morphological (particle-size distribution (PSD), scanning electron microscopy (SEM), powder x-ray diffraction (PXRD), skeletal density). Each preparation had similar properties to the other preparations except for PSD and PXRD. For PSD, all preparations exhibited a mono-modal distribution with a variation in median values from ~ 40 μm to over 80 μm. All PXRD values indicated the same morphology with minor variations in crystal orientations. Possible polymorphism was also observed in a few cases. SEM images and PXRD indicate all preparations to be diamond-type and X-type crystals with some twinning. Impact, friction, and ESD and thermal sensitivities values are consistent with these type of crystal habits as seen in vast literature studies.

Explosive characterization↗
DOE OSTI2024

Surface Modified Fly Ash for Value Added Products (SuMo Fly Ash)

The objective of this project is to develop a technology to encapsulate coal fly ash particles in sulfurized vegetable oil, enhancing physical and mechanical properties of the fly ash as a filler material when applied in commercial products. This project significantly advances the knowledge base and technology for synthesizing coated fly ash particles for application in different polymer matrices to increase cross-linking, compatibility, air-entrainment and to decrease the leaching potential of metals of concern. Specifically, the project focuses on (a) collection, and characterization of fly ash material from coal power plants; (b) development of Sulfurized Vegetable Oil (SVO) modified (SuMo) fly ash and their detailed characterization; (c) evaluation of the mechanical properties of the SuMo fly ash incorporated plastic and rubber composites for potential replacement of CaCO 3 or carbon black as filler materials with SuMo fly ash in plastic and rubber composites; (d) leaching potential of SuMo fly ash and SuMo fly ash-incorporated plastic and rubber composites to determine the rate of release of trace metals. The major findings of this project are: i) Sulfurized Vegetable Oil coated fly ash (SuMo fly ash) was successfully prepared with a particle size of ≤ 45 micron which exhibited hydrophobicity of contact angle > 90°; ii) the coating reduces leaching of metals (e.g., B, Cr) from fly ash when exposed to water; iii) incorporation of SuMo fly ash increases thermal stability and yield strength of plastics; iv) SuMo coating helps disperse fly ash particles into cured rubbers, natural rubber; (v) SuMo fly ash-incorporated plastic/cured rubbers compounds protects against leaching of toxic elements.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Experimental and Computational Characterization of a Modified Sioutas Cascade Impactor for Respirable Radioactive Aerosols

Oak Ridge National Laboratory is collecting and characterizing aerosols released when spent nuclear fuel (SNF) rods are fractured in bending. An aerosol collection system was designed and tested to collect respirable sized (<10 μm aerodynamic diameter [AED]) particulates inside a hot cell facility. The setup is a modified version of the commercially available Sioutas cascade impactor, to which additional stages were added to expand the aerosol collection range from 2.5 to ~15 μm AED. To accommodate the additional stages and specific test conditions, the operating flow rate for aerosol collection was reduced, and testing was conducted by using pressure drop measurements, surrogate dust collection, and particle size characterization. The fluid flow distribution within the cascade and its stages was simulated in STAR-CCM+, and the stage-wise pressure drops obtained using the computational fluid dynamics model were then compared to experimental data. Lagrangian particle simulations were also performed, and stage-wise collection statistics were obtained from the simulation for comparison with the experimental data obtained using SNF-surrogate dust particles. The results provide valuable insights into the stage-wise particle collection characteristics of the modified cascade impactor and can also be used to improve the prediction accuracy of the manufacturer-determined analytical correlations.

aerosol modeling↗
DOE OSTI2026

Insights into the Structure of Ultrasmall Fluorescent Core–Shell Silica Nanoparticles

Ultrasmall fluorescent core–shell nanoparticles (NPs) with a silica core and poly(ethylene glycol) ligand shell are the earliest example of hybrid NPs that have received U.S. investigational new drug FDA approval. They are among only a few inorganic NPs translated to safety, diagnostic, and therapeutic human clinical trials. Despite these achievements, little is known about the exact structure of their 3–4 nm sized silica cores. We report the surprising discovery of a well-defined pentagonal bipyramidal core structure preferentially formed in the aqueous synthesis built from seven primary silica NPs. A combination of reverse-phase high-performance liquid chromatography, cryogenic transmission electron microscopy, and coarse-grained simulations provides fundamental insights into this magic-size cluster formation and its unusual stability. Here, results rationalize the successful NP synthesis scale-up from 1 mL to 50 L, provide clues to the recent discovery of their self-therapeutic properties in oncology via ferroptosis, an iron-dependent cell death mechanism, and promise improved control of particle size distribution via chromatographic separations.

cluster chemistry↗
DOE OSTI2025

Predicting Liquid–Liquid Phase Separation of Submicrometer Proxies for Atmospheric Secondary Aerosol

Liquid–liquid phase separation (LLPS) of atmospheric aerosols can significantly impact climate, air quality, and human health. However, their complex composition, small size, and history-dependent properties result in great uncertainty in the modeling of aerosol phase state and atmospheric processes. Herein, using cryogenic transmission electron microscopy (cryo-TEM), we examined model submicron aerosols composed of organic compounds and ammonium sulfate, and established a parameterization for the separation relative humidity (SRH) that accounts for chemical composition, particle size, and equilibration time. We evaluated different variables that describe chemical composition: O/C ratio, partition coefficient, solubility, molar mass, and polarizability. The O/C ratio fits the SRH of micrometer droplets best, and by using a scaling factor to translate the micrometer SRH parameterization to submicron aerosols, we incorporate the effects of size and equilibration time. The measured scaling factor for the submicron mean SRH (30nm – 1μm, 20 min equilibration times) is 0.80, the factor becomes 1 with equilibration time over 1 hour, and is equal to 0, meaning that SRH is absent, when the aerosol dry diameter is smaller than 30 nm. Furthermore, our parameterization will aid in universal SRH modeling, potentially leading to more accurate predictions of aerosol mass, optical properties, hygroscopicity, and heterogeneous chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Compositing and Characterization of SE Quadrant Waste Exemplars

This report outlines the experimental investigation and characterization of transport properties in Hanford SE quadrant High-Level Waste (HLW). The goal of the study was to establish baseline behaviors of bulk composite rheology and settling characteristics to facilitate waste treatment process design for the Waste Treatment and Immobilization Plant (WTP) and avoid waste conditions and properties favorable to bubble cascade gas release events. The study focused on two major objectives: 1) identifying, obtaining, and preparing relevant Hanford tank waste samples for evaluation and 2) quantifying the “as-received” rheology and transport properties of the samples. Twenty-three centrifuged core segments originating from tanks AN-101, AN-106, and AW-105 were selected based on compositional relevance to SE quadrant PUREX cladding waste. These materials were composited into five waste composites enriched with target analytes: aluminum (Al), iron (Fe), phosphate (PO 4 ), uranium (U), and zirconium (Zr). Physical property and transport testing examined particle size distributions, bulk densities, settling behaviors, rheological properties, shear strengths, and just-suspended mixing speeds (NJS). Testing revealed two distinct composite classifications based on rheological characteristics: non-Newtonian composites (Fe and PO 4 ) and Newtonian composites (Al, U, and Zr). The Fe and PO 4 composites exhibited slow settling rates and reduced mobilization proclivity, attributable to strong particle-particle interactions and the formation of yield structures within non-Newtonian slurries. In contrast, the Al, U, and Zr composites displayed rapid settling and dense compaction behaviors, indicative of minimal structuring and interactions. Shear strengths for all composites were generally low relative to prior studies of SE quadrant waste, with only the U composite showing elevated strength approaching values reported in previous literature. Repeat shear strength measurements revealed contributions from dense granular material in the U composite and stronger cohesive properties in the Al composite. Settling data highlighted hindered settling behavior, with rates falling more than one order of magnitude below estimates based on Stokes’ law and rate decreasing as composite UDS content increased. NJS testing demonstrated different mobilization behaviors between cohesive and granular composites. The Fe composite required the highest mixing rate for resuspension, while the Al composite was the easiest to resuspend. Comparison of measured NJS against predictions made using the Zwietering correlation suggests non-Newtonian behavior alters resuspension mechanics, rendering non-Newtonian systems more stable against resuspension lift forces relative to their granular counterparts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Single particle – MC-ICP-MS for isotopic analysis of uranium particles

Single particle – multi-collector – inductively coupled plasma – mass spectrometry (SP-MC-ICP-MS) was employed to measure a suspension of 1 µm U3O8 particles (∼1.3 pg total U/particle) to determine their individual isotopic compositions of 234U/238U, 235U/238U, and 236U/238U. The effects of different detector combinations for 235U and 238U, including secondary electron multipliers (SEM) and Faraday detectors (1011 and 1013 Ω amplifiers), were explored for accuracy and precision optimization on the observed 235U/238U. The minor isotopic ratios (i.e., 234U/238U and 236U/238U) were analyzed such that the 234U and 236U were monitored on SEM detectors and the 238U was monitored on a Faraday (1011 Ω) detector. Various integration times (5, 10, 25, and 50 ms) were investigated in all detector configurations to gain a better understanding of their impact on sensitivity, accuracy, and precision. For 235U/238U ratios of 1 µm U3O8 particles, a dual Faraday detector measurement with 1011 Ω was the optimal choice; measurement of 1021 particles yielded an average 235U/238U ratio of 0.00170 (14), a −1.8% relative difference (% RD) from the reference value. The minor isotopic compositions were determined to be 0.0000070 (14) and 0.0000758 (48) for the 234U/238U and 236U/238U, respectively. These measurements correspond to <8% and <1% RD from their reference value for the 234U/238U and 236U/238U, respectively. SP-MC-ICP-MS was also able to provide insight into measurement sensitivity. In these individual particles, merely 15 and 165 atto-grams (ag) of 234U and 236U were present (calculated). Initial limits of detection for SP-MC-ICP-MS were determined to be ∼1.0 ag (when measured via SEM detectors). This valuable approach is applicable to areas including nuclear forensics, nuclear safeguards, and geochemical analysis, which require high-precision measurements of uranium within micron-sized particles.

Manard, Benjamin [ORNL] (ORCID:0000000207400627)↗
DOE OSTI2025

In situ probing of structure and deagglomeration of SnO 2 colloids via small-angle X-ray scattering

Transforming dry nanopowders into stable colloidal dispersions remains challenging due to the cohesive forces between the nanoparticles (NPs) which promote agglomeration. Effective dispersion and deagglomeration of these agglomerates is a critical process in the formulation and preparation of nanoparticle-based functional materials via the colloidal route. Understanding the deagglomeration dynamics provides information to improve microstructural quality in various applications by enabling engineering of agglomerate size, structure and morphology. However, the deagglomeration process dynamics with respect to the evolution of the fractal agglomerate structures, particularly for very small NPs, is still poorly understood and requires further investigation. This study employs in situ small-angle X-ray scattering (SAXS) to investigate the sonication-induced deagglomeration of SnO 2 NPs. Electrostatically stabilized SnO 2 colloids with varying primary particle size (6–21 nm) are investigated in a specifically designed in situ cell using synchrotron-based SAXS to study the influence of sonication time and intensity on the nanoscaled agglomerates. Complete structural analysis via SAXS reveals a direct correlation between changes in agglomerate size and structure, size-dependent deagglomeration behavior and a dependence on the overall energy introduced during sonication into the dispersion regardless of the actual power as well as ultrasonic process parameters in case of SnO 2 NPs. The results suggest that control of the dispersion process during ultrasonic deagglomeration results in tailoring agglomerates with respect to size and structure.

Deagglomeration↗
DOE OSTI2025

In-Tank Processing Using Low Temperature Aluminum Dissolution: Year 1 Progress Report

The Hanford Site stores approximately 56 million gallons of radioactive legacy defense waste in underground tanks. This study investigates the feasibility of utilizing in-tank low-temperature aluminum dissolution to favorably alter the transport properties of aluminum-rich southeast quadrant waste sludges, thereby de-risking sludge delivery for Direct Feed of High-Level Waste. Specifically, this study aims to assess the rate and extent of gibbsite dissolution under various conditions, including different particle sizes (~10 to 90 µm), NaOH concentrations (1 to 6 M), and the presence of specific analytes such as NO 2 - , NO 3 - , and other aluminum-rich waste background analytes, using simulated waste solids and liquids. Experimental tests were designed to highlight the impact of aluminum leaching on simulated waste transport properties, quantified by the just-suspended mixing speed (NJS), and were conducted under well-mixed, turbulent conditions, ensuring full suspension of gibbsite particles using an overhead mixer. The results suggest that the presence of NO 2 - and NO 3 - , in conjunction with leaching at relatively low free hydroxide contents, improved transport requirements (i.e., lowered NJS) for pure gibbsite slurries. These findings will inform the design of potential in-tank processing systems, optimizing aluminum dissolution for improved waste management in the Hanford Tank Farms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Dust Direct Radiative Effect Including Large Particles and Component Minerals

The direct radiative effect (DRE) of dust aerosols in Earth system models (ESMs) remains highly uncertain, largely due to inadequate representations of particle size distribution (PSD) and mineral composition. Using NASA's Earth Surface Mineral Dust Source Investigation (EMIT) soil mineralogy data and observed PSD in an ESM that resolves dust mineral composition and emitted diameters from 0.1 to 70 μm, we find a near-neutral global dust net DRE (−0.057 W m −2 ), weaker than most previous estimates. Large dust (diameter >10 μm) contributes 30% of the global longwave dust optical depth, providing observational constraints on large-particle abundance, and offsets 20% of the dust shortwave cooling over major source regions. Incorporation of EMIT mineralogy reduces shortwave uncertainty by more than 50%. The remaining uncertainty mainly exists in processes controlling dust abundance, particularly the poorly understood transport of large dust, and longwave optical properties, which require additional observational constraints to more accurately quantify the dust DRE.

Li, Longlei [Cornell Univ., Ithaca, NY (United Sta↗
DOE OSTI2025

Effect of growth dynamics on the structural, photophysical and pseudocapacitance properties of famatinite copper antimony sulphide colloidal nanostructures (including nanosheets)

Facile phase selective synthesis of copper antimony sulphide (CAS) nanostructures is important because of their tunable photoconductive and electrochemical properties. In this study, off-stoichiometric famatinite phase CAS (fCAS) quasi-spherical and quasi-hexagonal colloidal nanostructures (including nanosheets) of sizes, 2.4–18.0 nm were grown under variable conditions of temperature (60–200 °C), time and oleylamine capping ligand concentration using copper(II) acetylacetonate and antimony(III) diethyldithiocarbamate precursors. Data from powder X-ray diffraction, Raman spectroscopy and high-resolution scanning/transmission electron microscopy confirm the tetragonal structure of the famatinite phase. X-ray photoelectron spectroscopy, transmission electron microscopy and scanning electron microscopy-energy dispersive X-ray spectroscopy data suggest a correlation of particle size, morphology and composition of the off-stoichiometric fCAS nanostructures with growth temperature and time, and oleylamine concentration. The off-stoichiometric Cu 3-a Sb 1+b S 4±c (a, b, c – mole fractions) nanostructures being severely copper-deficient and antimony-rich, exhibit shallow-lying acceptor copper vacancy states, deep-lying donor states of antimony interstitials, sulphur vacancies and antimony-copper antisites and shallow-lying acceptor surface trapping states. Further, these electronic states are likely implicated in tunable UV-visible absorption and bandgaps between 2.3 and 2.8 eV, and broad visible-NIR photoluminescence with fast recombination of radiative lifetimes between 0.2 and 6.2 ns, confirmed from absorption, steady-state and time-resolved photoluminescence spectroscopies. Additionally, cyclic voltammetry and electrochemical impedance spectroscopy confirm that electrodes of the fCAS nanostructures display slightly variable pseudocapacitance of charge-storage primarily via possible sodium ion intercalation with a high specific capacitance of ~84 F g -1 obtained at a scan rate of 5 mV s -1 . Overall, these results show the influence of composition, in particular point defects, phase quality and morphology on the optical and pseudocapacitance properties of fCAS nanostructures, suitable as solar absorbers or electrodes for energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Sequential surface synthesis of dispersed sub-nanometer iridium on titanium nitride for acidic water oxidation

Maximizing iridium utilization while maintaining high oxygen evolution reaction (OER) performance remains a persistent challenge in acidic water electrolysis. Immobilizing Ir on conductive, acid-stable supports is promising, yet simultaneously achieving sub-nanometer size, high area coverage, and strong electronic coupling is difficult. Here, we report a sequential surface synthesis on titanium nitride (TiN) that yields uniformly distributed sub-nanometer Ir arrays (∼0.7 nm). Our method uses ethylenediaminetetraacetic acid (EDTA) as a temporal scaffold: it chemisorbs to TiN to install dense chelating sites, captures Ir 3+ ions, and confines Ir cluster growth. A subsequent thermal treatment at 500 °C in a reducing atmosphere removes the ligand shell, while preserving ultrasmall particle size and establishing direct Ir–TiN electronic coupling. The optimized catalyst exhibits mixed Ir 0 /Ir x+ coordination with low charge-transfer resistance (R ct = 19.2 Ω), delivering a mass activity of 342 A g Ir −1 at 1.54 V in acidic electrolyte. In situ X-ray absorption spectroscopy reveals irreversible surface oxidation as the primary stability-limiting factor. This stepwise strategy provides a general framework for supported catalysts that maximize precious metal utilization via sub-nanometer dispersion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Leveraging Hydration Forces for Size-Specific Nanoparticle Enrichment with a Redox-Responsive Silica-Binding Elastin-Like Polypeptide

Elastin-like polypeptides (ELPs) are low-complexity proteins that coacervate above a characteristic lower critical solution temperature (LCST). While the thermoresponsiveness of ELPs has been widely exploited in the biomedical and biomaterials fields, their ability to mediate nanoparticle assembly below their transition temperature remains largely unexplored. Here, we show that unmodified ELPs induce the reversible flocculation of silica nanoparticles (SiNPs) by forming backbone hydrogen bonds with surface silanols. Interparticle bridging is modulated by ELP length and concentration and by the presence of N- and C-terminal anchoring groups such as a cysteine residue and a Car9 silica-binding peptide. Using a redox-responsive fusion protein consisting of disulfide-bonded ELP domains terminated by Car9 segments, we stabilize 20 nm SiNPs under oxidizing conditions while triggering particle flocculation upon addition of reductant. We find that SiNP sedimentation under reducing conditions exhibits a sharp dependency on particle size that arises from the curvature-dependent structure of surface silanols. While the isolated silanols of SiNPs smaller than 30 nm are efficiently engaged by the ELP domains of Car9-anchored proteins, repulsion forces associated with the presence of a layer of molecular water together with increased electrostatic repulsion preclude efficient engagement of H-bonded silanols displayed on the surface of SiNPs larger than 60 nm. We harness these findings to selectively enrich SiNPs based on size and expand the concept to titania (TiO2) by demonstrating that rutile nanoparticles can be stabilized or sedimented with solid-binding ELPs by adjusting the solution pH to promote or discourage the formation of a hydration layer. These strategies should prove broadly useful for the separation of other oxides and their polymorphs and provide a tunable strategy for nanoparticle assembly and bioinspired colloidal design.

ELP↗
DOE OSTI2024

Investigating New Particle Formation and Growth Over an Urban Location in the Eastern Mediterranean

Abstract This study investigates the new particle formation (NPF) events at an urban location in the Eastern Mediterranean. Particle size distribution, particulate chemical composition, and gaseous pollutants were monitored in Rehovot, Israel (31°53″N 34°48″E) during two campaigns: from April 29 to 3 May 2021 (Campaign 1) and from May 3 to 11 May 2023 (Campaign 2), coinciding with an intensive bonfire burning festival. The organic aerosols (OA) source apportionment identified two major factors—Hydrocarbon‐like OA and Biomass‐burning OA—as well as two secondary factors—MO‐OOA (more oxidized‐oxygenated OA) and LO‐OOA (low oxidized oxygenated OA). NPF events were frequently observed during the day (mostly well‐defined nucleation events) and at night (burst of ultrafine mode particles without any discernible growth). A condensation sink value of (9.4 ± 4.0) × 10 −3 s −1 during Campaign 1 and (14.2 ± 6.0) × 10 −3 s −1 during Campaign 2 was obtained. The daytime events were associated with enhanced sulfuric acid proxy concentrations of (2–12) × 10 6 molecules cm −3 , suggesting the role of gas‐phase photochemistry in promoting NPF. A novel approach of hybrid positive matrix factorization analysis was used to deconvolve the chemical species responsible for the observed events. The results suggest the involvement of multiple components, including ammonium sulfate and MO‐OOA, in the nucleation; Nitrate, HOA and LO‐OOA participate in the subsequent particle growth for the daytime events. Nighttime events involve only semi‐volatile species (LO‐OOA, HOA and nitrate) along with ammonium sulfate.

Meteorology & Atmospheric Sciences↗