Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development of a continuous linear model of a d-c to d-c flyback converter.

The analytical design of the feedback circuit for a d-c flyback converter requires the formulation of a model defining the static and dynamic performance of the forward loop. This paper describes the steps which were taken to develop a linear continuous model of a typical flyback circuit. Although the method uses several approximations to simplify the work, the resulting model was found to duplicate the performance of the actual circuit very closely. The model makes it possible to design the feedback circuit using well known linear feedback techniques. The method is an extension of prior work in the modeling of pulse-width controlled circuits.

Wells, B. A.↗
NASA NTRS1973

A fluidic device for measuring constituent masses of a flowing binary gas mixture

A continuous reading mass flow device was developed to measure the component flow of a binary gas mixture. The basic components of the device are a fluidic humidity sensor and a specially designed flow calorimeter. These components provide readings of gas mixture ratio, mixture heat capacity, heat dissipated by the calorimeter and the gas temperature rise across the calorimeter. These parameter values, applied in the general definitions of specific heat capacity and the heat capacity of a gas mixture, produce calculated component flow rates of the mixture being metered. A test program was conducted to evaluate both the steady state and dynamic performance of the device.

Prokopius, P. R.↗
NASA NTRS1973

Flexible rotor dynamics analysis

A digital computer program was developed to analyze the general nonaxisymmetric and nonsynchronous transient and steady-state rotor dynamic performance of a bending- and shear-wise flexible rotor-bearing system under various operating conditions. The effects of rotor material mechanical hysteresis, rotor torsion flexibility, transverse effects of rotor axial and torsional loading and the anisotropic, in-phase and out-of-phase bearing stiffness and damping force and moment coefficients were included in the program to broaden its capability. An optimum solution method was found and incorporated in the computer program. Computer simulation of experimental data was made and qualitative agreements observed. The mathematical formulations, computer program verification, test data simulation, and user instruction was presented and discussed.

Shen, F. A.↗
NASA NTRS1973

Criteria for structural test

The results of a study to define criteria and techniques of design, analysis and test which permit the use of a single major structural test article for performing dynamic, fatigue, and static testing are presented. The criteria developed is applicable to both space vehicles and aircraft structures operating in the subsonic or supersonic regime. The feasibility of such an approach was demonstrated by defining test interactions, compatibilities and incompatibilities between the three different types of tests. The results of the study indicate that the single test article concept is feasible with a testing sequence of dynamic test followed by a fatigue and static test.

Source record↗
NASA NTRS1973

The application of standardized control and interface circuits to three dc to dc power converters.

Standardized control and interface circuits were applied to the three most commonly used dc to dc converters: the buck-boost converter, the series-switching buck regulator, and the pulse-modulated parallel inverter. The two-loop ASDTIC regulation control concept was implemented by using a common analog control signal processor and a novel digital control signal processor. This resulted in control circuit standardization and superior static and dynamic performance of the three dc-to-dc converters. Power components stress control, through active peak current limiting and recovery of switching losses, was applied to enhance reliability and converter efficiency.

Yu, Y.↗
NASA NTRS1974

Computer program for flexible rotor dynamics analysis

Program analyzes general nonaxisymmetric and nonsynchronous transient and steady-state rotor dynamic performance of bending- and shear-wise flexible rotor-bearing system under various operating conditions. Program can be used as analytical study tool for general transient spin-speed and/or non-axisymmetric rotor motion.

Shen, F. A.↗
NASA NTRS1973

ASDTIC control and standardized interface circuits applied to buck, parallel and buck-boost dc to dc power converters

Versatile standardized pulse modulation nondissipatively regulated control signal processing circuits were applied to three most commonly used dc to dc power converter configurations: (1) the series switching buck-regulator, (2) the pulse modulated parallel inverter, and (3) the buck-boost converter. The unique control concept and the commonality of control functions for all switching regulators have resulted in improved static and dynamic performance and control circuit standardization. New power-circuit technology was also applied to enhance reliability and to achieve optimum weight and efficiency.

Schoenfeld, A. D.↗
NASA NTRS1973

The application of the analog signal to discrete time interval converter to the signal conditioner power supplies

The Analog Signal to Discrete Time Interval Converter microminiaturized module was utilized to control the signal conditioner power supplies. The multi-loop control provides outstanding static and dynamic performance characteristics, exceeding those generally associated with single-loop regulators. Eight converter boards, each containing three independent dc to dc converter, were built, tested, and delivered.

Schoenfeld, A. D.↗
NASA NTRS1973

Toward understanding the conical arc-chamber driver

The mechanical and electrical characteristics of the conical arc-chamber driver and the 1450-microfarad capacitor bank are described. The system dynamic performance can be approximated by a second-order nonlinear equation. The discharge of the capacitor bank into the conical arc-chamber was investigated at a variety of initial conditions. Details of the discharge are explained and compared for typical performance with both hydrogen and helium arc-chamber gases. At peak current the hydrogen plasma resistivity is significantly higher than that of the helium plasma and this, in part, accounts for the better shock speed performance with hydrogen. The lower melting and boiling point exploding wires of aluminum, copper, and stainless steel produced higher shock speed performance than the apparently nonexploding tungsten wire.

Livingston, F. R.↗
NASA NTRS1975

Frequency modulated cutaneous orientation feedback from artificial arms

A model of the human arm, emphasizing the neuromuscular mechanisms of feedback control, has been constructed. The various parameters and functions of physiological receptors in the feedback section have been classified into an automated category that can be incorporated in the prosthesis servo loop, and into a sensory category that should be communicated to the operator if control and dynamic performance are to be optimized. A scheme for simultaneous display of two such sensory parameters, i.e., fingertip pressure and elbow position, has been developed, implemented and evaluated. The neurophysiological mechanism of such displays, and the feasibility of sensory transformation, is discussed in this paper.

Solomonow, M.↗
NASA NTRS1974

Fatigue life of high-speed ball bearings with silicon nitride balls

Evaluation of hot-pressed silicon nitride as a rolling-element bearing material. Two grades of hot-pressed silicon nitride balls were tested under rolling contact conditions in a five-ball fatigue tester. A digital computer program was used to predict the dynamic performance characteristics and fatigue life of high-speed ball bearings with silicon nitride balls relative to that with bearings containing steel balls. The results obtained include the finding that fatigue spalls on silicon nitride balls are similar in appearance to those obtained with typical bearing steels.

Parker, R. J.↗
NASA NTRS1975

Squeeze film dampers - Amplitude effects at low squeeze numbers

Gaseous squeeze film dampers are analyzed to determine the effect of periodic disturbance amplitude on the dynamic performance. Both circular and rectangular parallel surfaces are investigated. A solution of the nonlinear Reynolds equation is obtained by expanding the pressure in powers of the squeeze number, retaining up to and including terms of the order of the square of the squeeze number. The time dependent load characteristics are found. The effect of disturbance amplitude on the film stiffness and damping is given.

Sadd, M. H.↗
NASA NTRS1975

Drive-train dynamics technology - State-of-the-art and design of a test facility for advanced development

A program for the development and verification of drive-train dynamic technology is described along with its basis and the results expected from it. A central feature of this program is a drive-train test facility designed for the testing and development of advanced drive-train components, including shaft systems, dampers, and couplings. Previous efforts in designing flexible dynamic drive-train systems are reviewed, and the present state of the art is briefly summarized. The design of the test facility is discussed with major attention given to the formulation of the test-rig concept, dynamic scaling of model shafts, and the specification of design parameters. Specific efforts envisioned for the test facility are briefly noted, including evaluations of supercritical test shafts, stability thresholds for various sources and types of instabilities that can exist in shaft systems, effects of structural flexibility on the dynamic performance of dampers, and methods for vibration control in two-level and three-level flexible shaft systems.

Badgley, R. H.↗
NASA NTRS1976

Development of dynamic calibration methods for POGO pressure transducers

Two dynamic pressure sources are described for the calibration of pogo pressure transducers used to measure oscillatory pressures generated in the propulsion system of the space shuttle. Rotation of a mercury-filled tube in a vertical plane at frequencies below 5 Hz generates sinusoidal pressures up to 48 kPa, peak-to-peak; vibrating the same mercury-filled tube sinusoidally in the vertical plane extends the frequency response from 5 Hz to 100 Hz at pressures up to 140 kPa, peak-to-peak. The sinusoidal pressure fluctuations can be generated by both methods in the presence of high pressures (bias) up to 55 MPa. Calibration procedures are given in detail for the use of both sources. The dynamic performance of selected transducers was evaluated using these procedures; the results of these calibrations are presented. Calibrations made with the two sources near 5 Hz agree to within 3% of each other.

Hilten, J. S.↗
NASA NTRS1978

Hydraulic dynamic analysis

Computer program mathematically describes complete hydraulic systems to study their dynamic performance. Program employs subroutines that simulate components of hydraulic system, which are then controlled by main program. Program is useful to engineers working with detailed performance results of aircraft, spacecraft, or similar hydraulic systems.

Gale, R. L.↗
NASA NTRS1978

Air cushion landing system

Static and dynamic performance of air cushion landing system is simulated in computer program that treats four primary ACLS subsystems: fan, feeding system, trunk, and cushion. Configuration of systems is sufficiently general to represent variety of practical designs.

Boghami, K. M.↗
NASA NTRS1977

Slotted test section dynamics of the NTF

A dynamic model of the National Transonic Facility (NTF) section and plenum chamber was developed. The model serves as a means for determining the dynamic performance of the NTF and the subsequent design of optimal control configurations, and is of one dimensional flow type as to facilitate computer simulation. The model allows for the simulation of the effects of test section blockage, boundary layer losses, slot flow required for supersonic flow generation, reentry flap position, and auxiliary plenum suction.

Gumas, G.↗
NASA NTRS1978

Procedures for generation and reduction of linear models of a turbofan engine

A real time hybrid simulation of the Pratt & Whitney F100-PW-F100 turbofan engine was used for linear-model generation. The linear models were used to analyze the effect of disturbances about an operating point on the dynamic performance of the engine. A procedure that disturbs, samples, and records the state and control variables was developed. For large systems, such as the F100 engine, the state vector is large and may contain high-frequency information not required for control. This, reducing the full-state to a reduced-order model may be a practicable approach to simplifying the control design. A reduction technique was developed to generate reduced-order models. Selected linear and nonlinear output responses to exhaust-nozzle area and main-burner fuel flow disturbances are presented for comparison.

Seldner, K.↗