Search NASA⌕ Search

SEARCH · Search NASA

Results for “failure analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Failure analysis of a tool steel torque shaft

A low design load drive shaft used to deliver power from an experimental exhaust heat recovery system to the crankshaft of an experimental diesel truck engine failed during highway testing. An independent testing laboratory analyzed the failure by routine metallography and attributed the failure to fatigue induced by a banded microstructure. Visual examination by NASA of the failed shaft plus the knowledge of the torsional load that it carried pointed to a 100 percent ductile failure with no evidence of fatigue. Scanning electron microscopy confirmed this. Previously announced in STAR as N82-11184

Reagan, J. R.↗

Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

Abstract Novel methods for advancing reliability testing of photovoltaic (PV) modules and materials have recently been developed. Combined-accelerated stress testing (C-AST) is one such method which has demonstrated reliable reproduction of some field-failures which were not reproducible by standard certification tests. To increase confidence and assist in the development of C-AST, and other new testing protocols, it is important to validate that the failure modes observed and mechanisms induced are representative of those observed in the field, and not the product of unrealistic stress conditions. Here we outline a method using appropriate materials characterization and modelling to validate the failure mechanisms induced in C-AST such that we can increase confidence in the test protocol. The method is demonstrated by applying it to a known cracking failure of a specific polyamide (PA)-based backsheet material. We found that the failure of the PA-based backsheet was a result of a combination of stress factors. Photo-oxidation from ultra-violet (UV) radiation exposure caused a reduction in fracture toughness, which ultimately lead to the cracking failure. We show that the chemical and structural changes observed in the backsheet following C-AST aging were also observed in field-aged samples. These results increase confidence that the conditions applied in C-AST are representative of the field and demonstrates our approach to validating the failure mechanisms induced.

14 SOLAR ENERGY↗

Towards Validation of Advanced Accelerated Stress Testing Protocols through Failure Analysis and Materials Characterization

As the lifetime of photovoltaic modules increases toward the goal of 50 years, accelerated stress testing is critical to assessing the viability of newer, improved, and often cheaper materials in the field. However, the validation of accelerated testing to reproduce field failure has remained elusive. The recent developments of more advanced stress testing protocols utilizing sequential and combined stressors have provided another opportunity for validation. Using a suite of mechanical, chemical, and structural characterization methods we report the development of our approach using a known bad backsheet “AAA.” We then apply this approach to PVDF-based backsheets to further confirm the generalizability of this approach. The outcome of this work is two-fold: (1) validation of advanced accelerated testing protocols which will enable the prediction of field failures in new materials, and (2) deeper insights into the degradation mechanisms observed through the extensive characterization allowing for improved materials engineering and development.

accelerated aging↗

An FEM-Based Peridynamic Model for Failure Analysis of Unidirectional Fiber-Reinforced Laminates

To predict the mixed damage modes of unidirectional fiber-reinforced polymer (FRP) laminates under dynamic loading, an FEM-based peridynamic model is introduced in this paper. Based on its geometric structure and material composition, a long fiber lamina is considered a transversely isotropic medium as a result of homogenization at the meso-scale. The laminated structure is modeled by stacking surface mesh layers with arbitrary fiber angles along the thickness direction. The peridynamic bonds between Gauss points connect the separated elements. These bonds are classified as inner-layer bonds and inter-layer bonds. To represent the anisotropy of a laminate, the micro-elastic modulus of the inner-layer and inter-layer bonds is calculated from the anisotropic engineering material constants separately. To capture complex failure behaviors of laminate structures, an empirical damage model is proposed for the tension/ compression breakage of peridynamic bonds. This damage model can control the in-plane and delamination failure process. Finally, benchmark tests are conducted to validate the elastic response of laminates under dynamic loading. In terms of damage analysis, the proposed model can capture the complex damage modes and resistive force of laminate structures.

36 MATERIALS SCIENCE↗

OH-58 helicopter transmission failure analysis

The OH-58 main transmission gearbox was run at varying output torques, speeds, and oil cooling rates. The gearbox was subsequently run to destruction by draining the oil from the gearbox while operating at a speed of 6200 revs per minute and 36,000 inch-pounds output torque. Primary cause of gearbox failure was overheating and melting of the planet bearing aluminum cages. Complete failure of the gearbox occurred in 28 1/2 minutes after the oil pressure dropped to zero. The alternating and maximum stresses in the gearbox top case were approximately 10 percent of the endurance limit for the material. Deflection of the bevel gear at 67000 inch-pounds output torque indicate a marginal stiffness for the bevel gear supporting system.

Townsend, D. P.↗

Photovoltaic module reliability improvement through application testing and failure analysis

During the first four years of the U.S. Department of Energy (DOE) National Photovoltatic Program, the Jet Propulsion Laboratory Low-Cost Solar Array (LSA) Project purchased about 400 kW of photovoltaic modules for test and experiments. In order to identify, report, and analyze test and operational problems with the Block Procurement modules, a problem/failure reporting and analysis system was implemented by the LSA Project with the main purpose of providing manufacturers with feedback from test and field experience needed for the improvement of product performance and reliability. A description of the more significant types of failures is presented, taking into account interconnects, cracked cells, dielectric breakdown, delamination, and corrosion. Current design practices and reliability evaluations are also discussed. The conducted evaluation indicates that current module designs incorporate damage-resistant and fault-tolerant features which address field failure mechanisms observed to date.

Dumas, L. N.↗

Failure Analysis Of Wood Gasifier Vessels

Gasification of biomass or streams containing biomass offers a means to produce syngas that can be combusted directly or converted to higher value products. Oak Ridge National Laboratory (ORNL) staff members have investigated and reported on corrosion that was encountered in several types of biomass gasifiers the most recent of which involved failure of carbon steel shells of wood chip gasifiers. The investigation of these wood chip gasifiers determined that incomplete gasification of the biomass resulted in formation of a wide range of organic compounds including low boiling point organic acids. These acids, unintentionally, had access through a narrow pathway to the surface of the carbon steel vessels, and condensation of the acids apparently caused severe corrosion of the steel in a very limited area around the circumference of the vessels. Laboratory studies were conducted in a carbon simulated environment, and several alloys with sufficient corrosion resistance were identified.

Keiser, Jim↗

FEA-Based Failure Analysis of Post-Buckled Composite Multi-Hat Stiffened Panel Under Static Compression

The aerospace industry uses composite multi-hat stiffened panels for skins because of their high strength-to-weight and stiffness-to-weight ratios. However, laminated composites with initial flaws are susceptible to delamination under buckling loads. The goal is to ensure damage initiation occurs past the buckled state, only stable damage progression at loads below the ultimate compressive load, and debonding failure past the ultimate compressive load. This approach reduces weight and addresses a potential design review for future aircraft repairs. The need exists to better understand damage initiation and growth mechanisms in composite structures while assisting in the design, analysis, and sustainment methods. Teflon inserts simulate damage defects during manufacturing, while barely visible impact helps capture human error during manufacturing. This work shows the interaction between the skin-stringer and ply-ply separations at the post-buckled state for both defect events using Abaqus Virtual Crack Closure Technique (VCCT). The initial configuration for the Teflon case was to leave the Teflon region unbonded, and the initial impact damage region approximation came from the experimental data and was considered the initial configuration. When compared against the experimental data produced through the NASA Advanced Composites Project (ACP), the present model captured damage transition from skin-hat to ply1-ply2. The model validations were within ~5% of the experimental data.

composite↗

Failure analysis of pinch-torsion tests as a thermal runaway risk evaluation method of Li-Ion Cells

Recently a pinch-torsion test is developed for safety testing of Li-ion batteries (Ren et al., J. Power Source, 2013). It has been demonstrated that this test can generate small internal short-circuit spots in the separator in a controllable and repeatable manner. In the current research, the failure mechanism is examined by numerical simulations and comparisons to experimental observations. Finite element models are developed to evaluate the deformation of the separators under both pure pinch and pinch-torsion loading conditions. It is discovered that the addition of the torsion component significantly increased the maximum principal strain, which is believed to induce the internal short circuit. In addition, the applied load in the pinch-torsion test is significantly less than in the pure pinch test, thus dramatically improving the applicability of this method to ultra-thick batteries which otherwise require heavy load in excess of machine capability. It is further found that the separator failure is achieved in the early stage of torsion (within a few degree of rotation). Effect of coefficient of friction on the maximum principal strain is also examined.

finite element analysis↗

NSLS-II Linac Klystron Filament Failure Analysis

The NSLS-II linear accelerator uses the TH2100A klystron tube. One tube has failed with broken window with less than 8000 hours. The tuning (impedance matching) posts were clearly bent, indicating that this tube had a mismatch at the window that was tuned out at the factory. None of our other tubes arrived like this. It is not clear if this was a contributing factor to the failure. This tube was purchased by BNL and installed after linac commissioning to verify operation. Tube delivered with linac held as spare and re-installed when this tube failed.

42 ENGINEERING↗

Failure analysis and performance evaluation of NASA inertial reference unit (DRIRU 2) after 50 months of orbital operation

The first production DRIRU 2 (NASA standard high performance inertial reference unit) system was launched as a subsystem of the Modular Attitude Control System for the Solar Maximum Mission (SMM) spacecraft in February 1980. This hardware was retrieved during the repair of the SMM during Shuttle Flight 41-C in April 1984 and returned to Teledyne Systems Company (manufacturer) for investigation and performance measurements as directed by Goddard Space Flight Center. A failure of one of the three gyro channels occurred approximately 6.5 months after launch. The built in redundancy functioned properly, the DRIRU 2 continued to provide the required attitude control function without performance degradation. Subsequent failure of other attitude control subsystems made the SMM a candidate for the first demonstration of the shuttle in-orbit repair capabilty. The in-orbit DRIRU 2 II failure scenario and the results of the analyses/tests conducted after retrieval are discussed. Comparison of this data with similar data prior to launch demonstates the excellent stability of performance parameters achieveable with DRIRU 2.

Green, K. N.↗

The Evolution of Failure Analysis at NASA's Kennedy Space Center and the Lessons Learned

The United States has had four manned launch programs and three station programs since the era of human space flight began in 1961. The launch programs, Mercury, Gemini, Apollo, and Shuttle, and the station programs, Skylab, Shuttle-Mir, and the International Space Station (ISS), have all been enormously successful, not only in advancing the exploration of space, but also in advancing related technologies. As each subsequent program built upon the successes of previous programs, they similarly learned from their predecessors' failures. While some failures were spectacular and captivated the attention of the world, most only held the attention of the dedicated men and women working to make the missions succeed.

metallography↗

Metrology and Failure Analysis for 3D IC Integration

At the same time as research in 3D TSV technology is advancing quickly, the analytical techniques used in the evaluation of 3D stacks must also advance in capability. Microscopy techniques for which silicon is opaque such as scanning acoustic microscopy (SAM) and confocal infrared (IR) microscopy are capable of inspecting the interface between bonded wafer pairs, while high resolution X-ray computed tomography (XCT) is used to detect voids in TSVs. With nano-XCT, voids in copper TSVs with sub-100 nm size can be visualized. For more detailed failure characterization, a target Focused Ion Beam (FIB) cross-section through the localized region of interest (defect) and subsequent scanning electron microscopy (SEM) imaging is proposed. Currently, the most important requirement is to reduce the so-called time-to-data, e. g. for defect localization using nano-XCT and for cross-section characterization.

36 MATERIALS SCIENCE↗

Rock failure analysis by combined thermal weakening and water jet impact

The influence of preheating on the initiation of fracture in rocks subjected to the impingement of a continuous water jet is studied. Preheating the rock is assumed to degrade its mechanical properties and strength in accordance with existing experimental data. The water jet is assumed to place a quasi-static loading on the surface of the rock. The loading is approximated by elementary functions which permit analytic computation of the induced stresses in a rock half-space. The resulting stresses are subsequently coupled with the Griffith criteria for tensile failure to estimate the change, due to heating, in the critical stagnation pressure and velocity of the water jet required to cause failure in the rock.

Nayfeh, A. H.↗

Failure analysis of nuclear transient-tested UN tristructural isotropic fuel particles in a 3D printed SiC matrix

Fully ceramic microencapsulated fuel elements containing UN tristructural isotropic (TRISO) fuel particles within a 3D printed SiC matrix were subjected to transient testing with varying energy depositions. Detailed post-irradiation examinations were performed, including leaching in hot HNO3 and post-leaching X-ray computed tomography, to quantify the percentage of failed TRISO particles and crack propagation within the particles and surrounding fuel matrix. In parallel, detailed finite element analyses were performed for comparison with experimental findings and to better evaluate transient failure modes. The lowest transient energy deposition—which still exceeded bounding values for high-temperature gas-cooled reactor applications—resulted in no detectable TRISO particle failures or matrix cracking, which was consistent with the simulations. Simulations of the higher-energy transients for which significant TRISO particle failure was expected were generally able to reproduce the transient temperatures and matrix cracking. Thus, the TRISO particle failures were explained based on the effects of local SiC matrix thickness and porosity. Results generally confirmed the high strength of the additively manufactured SiC matrix but also affirmed the need for a modified UN TRISO architecture to prevent SiC matrix cracks from propagating through TRISO layers. This unique failure mode has not historically been considered for TRISO fuels contained in weaker graphite matrices.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Time-to-failure analysis for NiCd batteries in a CPS orbit

Cells operating at five degrees Celsius or less, and going to 60 to 65 percent depth of discharge, were studied as to whether they could achieve a useful working life of 7.5 years in a GPS orbit. The characteristics of various orbits were compared and it is noted that the GPS orbit experiences only 220 cycles a year and must be treated as a geosynchronous rather than a low Earth orbit. Cell degradation is considered to be the result of both trickle-charge degradation and degradation due to cycling. Time-to-failure values are presented for selected temperatures and depth of discharges.

Sense, K. A.↗

Failure Analysis and Recovery of a 50mm Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

The ISS Distillation Assembly centrifuge is the pathfinder application for 50mm bore, deep-groove ball bearings made from the highly elastic intermetallic material 60NiTi. Superior corrosion and shock resistance are required to withstand the acidic wastewater exposure and heavy spacecraft launch related loads that challenge conventional steel bearings. During early ground testing one bearing unexpectedly and catastrophically failed after operating for only 200 hours of run time. A second bearing running on the same shaft was completely unaffected. A thorough investigation into the root cause of the failure determined that an excessively tight press-fit of the bearing outer race coupled with NiTis relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully duplicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

intermetallics↗

Failure Analysis and Recovery of a 50 MM Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

The ISS Distillation Assembly centrifuge is the pathfinder application for 50mm bore, deep-groove ball bearings made from the highly elastic intermetallic material 60NiTi. Superior corrosion and shock resistance are required to withstand the acidic wastewater exposure and heavy spacecraft launch related loads that challenge conventional steel bearings. During early ground testing one bearing unexpectedly and catastrophically failed after operating for only 200 hours of run time. A second bearing running on the same shaft was completely unaffected. A thorough investigation into the root cause of the failure determined that an excessively tight press-fit of the bearing outer race coupled with NiTis relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully duplicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

failure analyses↗