SEARCH · Search NASA

Results for “floating structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Debye Dielectric Model Function for Seawater Based on Expanded L-Band Measurement Data Set

New seawater dielectric measurements have recently been made over a broad range of salinities and temperatures at the George Washington University (GW). These measurements have been used to refine the existing dielectric model function of seawater for salinity retrieval. The mathematical structure of the new model function has been investigated to: (a) look for a physical basis for the mathematical form; and (b) to optimize the accuracy of data fitting. The Debye model has been chosen to represent the dielectric constant of seawater as a function of salinity (S), temperature (T) and frequency (f). The retrieved salinity using the Debye model has good agreement with the in-situ data collected by Argo floats. The global differences in retrieved salinity and in-situ data will be presented at the meeting.

ocean salinity↗

NASA NTRS1985

Chiral solidification of a phospholipid monolayer

The formation of chiral solidlike domains observed by Weiss and McConnell (1984) in monolayers of depalmitoylphosphatidylcholine (DPPC) floating on an air-water interface is investigated theoretically. It is proposed that the diffusion tensor for the two-dimensional fluidlike phase of the DPPC molecules has a chiral component acting perpendicular to the concentration gradient and coupled to the rotational motion of a pinwheellike molecule by the viscous forces. Diagrams are provided, and numerical estimates of the forces involved are shown to be in agreement with the observed behavior of the structures.

Langer, J. S.↗

NASA NTRS1991

Overpressurized zero pressure balloon system

Typical zero pressure scientific balloon systems experiencing diurnal cycles require on board expendable ballast to maintain design float altitude. In the past, pressurized balloon systems have been employed to overcome the need for ballast while maintaining small diurnal altitude excursions. However, requirements on material characteristics and manufacturing methods have enforced limitations on balloon size and therefore payload and altitude capabilities. This effort was aimed at considering the use of current (or slightly modified) zero pressure balloon systems (design, manufacturing and materials) as candidates for pressurized vehicles. Data gathered through performance analysis, structural analysis and flight testing has shown that the use of current zero pressure designs can be expanded to enhance balloon performance.

Simpson, Joel M.↗

NASA NTRS1998

Challenges of Future High-End Computing

The next major milestone in high performance computing is a sustained rate of one Pflop/s (also written one petaflops, or 10(circumflex)15 floating-point operations per second). In addition to prodigiously high computational performance, such systems must of necessity feature very large main memories, as well as comparably high I/O bandwidth and huge mass storage facilities. The current consensus of scientists who have studied these issues is that "affordable" petaflops systems may be feasible by the year 2010, assuming that certain key technologies continue to progress at current rates. One important question is whether applications can be structured to perform efficiently on such systems, which are expected to incorporate many thousands of processors and deeply hierarchical memory systems. To answer these questions, advanced performance modeling techniques, including simulation of future architectures and applications, may be required. It may also be necessary to formulate "latency tolerant algorithms" and other completely new algorithmic approaches for certain applications. This talk will give an overview of these challenges.

Bailey, David↗

NASA NTRS1983

Numerical simulations of plasma double layers

The results of analytical studies of quasi-static electric fields along geomagnetic field lines are discussed. The calculations were targeted at the structure, generation mechanisms and stability parameters. The field consists of two oppositely charged layers, either weakly or strongly charged, with an electric field between. Existence conditions are defined for the double layer field and balancing requirements are explored. Details of the simulation techniques, i.e., particle in cell and Vlasov simulations, for studying the double layer are outlined, noting that both periodic and quasi-periodic simulations are used. Solutions to Poisson's equation for fixed and floating point boundary conditions are generated. Finally, attention is also given to oblique and two-dimensional magnetic double layers.

Goertz, C. K.↗

NASA NTRS1990

The sheath structure around a negatively charged rocket payload

The sheath structure around a rocket payload charged up to 460 V negative relative to the ambient ionospheric plasma is investigated experimentally and by computer simulations. The experimental results come from the Charge 2 sounding rocket experiment in which the payload was split into two separate sections (mother and daughter) connected with a conducting, insulated tether. In one of the experimental modes, the voltage between the payloads was increased linearly from 0 to 460 V in 2.5 s. A floating probe array was mounted on the mother with probes located 25, 50, 75, and 100 cm from the rocket surface. The internal impedance of the array was smaller than the probe/plasma impedance, which influenced the potential measurements. The measurements contain signatures, resulting from the outward expansion of the ion sheath with increasing negative mother potential. This conclusion is substantiated by computer simulations of space charge limited flow.

Neubert, T.↗

NASA NTRS1999

Stability of Shapes Held by Surface Tension and Subjected to Flow

Results of three problems are summarized in this contribution. Each involves the fundamental capillary instability of an interfacial bridge and is an extension of previous work. The first two problems concern equilibrium shapes of liquid bridges near the stability boundary corresponding to maximum length (Plateau-Rayleigh limit). For the first problem, a previously formulated nonlinear theory to account for imposed gravity and interfacial shear disturbances in an isothermal environment is quantitatively tested in experiment. For the second problem, the liquid bridge is subjected to a shear that models the effect of a thermocapillary flow generated by a ring heater in a liquid encapsulated float-zone configuration. In the absence of gravity, this symmetric perturbation can stabilize the bridge to lengths on the order of 30 percent beyond the Plateau-Rayleigh limit, which is on the order of heretofore unexplained Shuttle observations. The third problem considers the dynamics of collapse and pinchoff of a film bridge (no gravity), which happens in the absence of stabilization. Here, we summarize experimental efforts to measure the self-similar cone-and-crater structure predicted by a previous theory.

Chen, Yi-Ju↗

NASA NTRSDate not supplied

Design and Applications of Tethered Spacecraft Simulators

Small, tethered spacecraft, or space tugs, are a promising space capability. They can be deployed on tethers and used for a wide variety of in-space activities; a large portion of which fall under in-space servicing, assembly, manufacturing (ISAM) functions. This includes functions such as structural mating and assembly, servicing, proximity operations, capture, docking, mating, and relocation. However, there is a great deal of work to be done to raise the Technology Readiness Level (TRL) of the capabilities needed to fully realize these capabilities. The Flat Floor Robotics Lab (FFRL) at NASA’s Marshall Spaceflight Center (MSFC) has been working on space tug development for several years. The eponymous floor is 44 by 86 feet, made from a self-leveling epoxy. This creates an extremely smooth surface that air bearings can float on with very little friction, creating a simulation of zero gravity in a two-dimensional plane. The lab has several platforms of various sizes that act as vehicle simulators for testing sensors, control algorithms, mechanisms, etc. One of these platforms is a small spacecraft simulator, which can be tethered to simulate a space tug. In the last several months, the FFRL team has been working with MSFC’s welding group to conduct a laser beam welding demonstration on air bearing platforms. This demo is utilizing a space tug simulator to fly up to a floating weld platform, where two parts are clamped together and laser welded. The space tug simulator has an air bearing to provide float, as well as several actuated air thrusters to provide propulsion and make the simulator maneuverable. Currently, flights of this simulator are completed by a human operator. An RF hand controller sends signals to both actuate and fire three sets of thrusters on the simulator. This makes any maneuvers of the space tug highly subject to human error, and operators must have dedicated practice time before being able to perform maneuvers with any sufficient reliability. For the current laser welding demonstration, human operated performance is sufficient, but future implementations of in-space welding and other ISAM efforts will require higher precision, reliability, and autonomy. MSFC has funded a project that will allow a small team in the FFRL to develop the next generation of space tug simulator, which will be automated. Closed loop control will allow a user to command a position, or set of positions, that the simulator will be able to “fly” to on its own. This Maneuverable Automated Tethered Spacecraft (MATS) simulator will have configurable design, to allow a variety of payloads and mission configurations to be demonstrated on the air bearing floor. This will be an invaluable test bed for low and mid TRL advancement for space tether mission subsystems, such as more advanced demonstrations of in-space welding. Once one MATSS is constructed and demonstrated effectively, several more can be built, enabling more advanced tether missions; Electric Sail test beds, sensor arrays, and other science-enabling missions. This paper will detail the design and test of the FFRL’s MATS simulator, including efforts to establish closed loop control and autonomous capabilities. It will also detail use cases for this technology, and how it will further develop both develop science and exploration missions.

Space Tethers↗

NASA NTRS1987

A microgravity isolation mount

The design and preliminary testing of a system for isolating microgravity sensitive payloads from spacecraft vibrational and impulsive disturbances is discussed. The Microgravity Isolation Mount (MGIM) concept consists of a platform which floats almost freely within a limited volume inside the spacecraft, but which is constrained to follow the spacecraft in the long term by means of very weak springs. The springs are realized magnetically and form part of a six degree of freedom active magnetic suspension system. The latter operates without any physical contact between the spacecraft and the platform itself. Power and data transfer is also performed by contactless means. Specifications are given for the expected level of input disturbances and the tolerable level of platform acceleration. The structural configuration of the mount is discussed and the design of the principal elements, i.e., actuators, sensors, control loops and power/data transfer devices are described. Finally, the construction of a hardware model that is being used to verify the predicted performance of the MGIM is described.

Jones, D. I.↗

NASA NTRS1999

Evaluation of a Treadmill with Vibration Isolation and Stabilization (TVIS) for Use on the International Space Station

A treadmill with vibration isolation and stabilization designed for the International Space Station (ISS) was evaluated during Shuttle mission STS-81. Three crew members ran and walked on the device, which floats freely in zero gravity. For the majority of the more than 2 hours of locomotion studied, the treadmill showed peak to peak linear and angular displacements of less than 2.5 cm and 2.5 deg, respectively. Vibration transmitted to the vehicle was within the microgravity allocation limits that are defined for the ISS. Refinements to the treadmill and harness system are discussed. This approach to treadmill design offers the possibility of generating 1G-like loads on the lower extremities while preserving the microgravity environment of the ISS for structural safety and vibration free experimental conditions.

McCrory, Jean L.↗

NASA NTRS2004

A Scalable Architecture of a Structured LDPC Decoder

We present a scalable decoding architecture for a certain class of structured LDPC codes. The codes are designed using a small (n,r) protograph that is replicated Z times to produce a decoding graph for a (Z x n, Z x r) code. Using this architecture, we have implemented a decoder for a (4096,2048) LDPC code on a Xilinx Virtex-II 2000 FPGA, and achieved decoding speeds of 31 Mbps with 10 fixed iterations. The implemented message-passing algorithm uses an optimized 3-bit non-uniform quantizer that operates with 0.2dB implementation loss relative to a floating point decoder.

optical communications↗

NASA NTRS1972

The observation of damage regions produced by neutron irradiation in lithium-doped silicon solar cells.

Study regions of lattice disorder produced in lithium-doped float-zone melted n/p-type silicon solar cells by irradiation with monoenergetic neutrons at doses between 10 to the 10th and 10 to the 13th per cu cm. The defect regions were revealed by chemically etching the surface of the solar cells and by observing carbon replicas in an electron microscope. It was found that the defect density increased with increasing irradiation dose and increased lithium content, whereas the average defect diameter was found to decrease. From thermal annealing experiments it was found that in the lithium-doped material the defect structure was stable at temperatures between 300 and 1200 K. This was found to be in contrast to the undoped material where at the lowest doses considerable annealing was observed to occur. These results are discussed in terms of the theoretical predictions and models of defect clusters proposed by Gossick (1959) and Crawford and Cleland (1959).

Ghosh, S.↗

NASA NTRS1971

Apollo 14 composite casting demonstration

This program assisted in the design and implementation of the composite casting demonstration for the Apollo 14 mission. Both flight and control samples were evaluated. Some conclusions resulting from a comparison of the flight and control samples were: (1) Solidification in neither the flight nor control samples was truly directional. (2) Apparent intermittent contact of the melt with the container in the flight samples led to unusual nucleation and growth structures. (3) There was greater uniformity, on a macro scale, of both pores and structural features in the flight sample; presumably the result of the reduced gravity conditions. (4) It seems quite feasible to produce enhanced dispersions of gases and dense phases in a melt which is solidified in reduced gravity. (5) A two-stage heating/cooling cycle may help directional solidification. (6) Sample materials should be selected from materials in which the dispersant fully wets the matrix material. (7) Experiments should be conducted in two modes: (1) where the melt is in good thermal contact with the container, and (2) where the melt is in a free-float condition.

Source record↗

NASA NTRS2006

Floating the Ball: Advances in the Technology of Electrostatic Levitation

Electrostatic Levitation (ESL) is an emerging technology. The MSFC ESL is a NASA facility that supports investigations of refractory solids and melts. The facility can be used to process a wide variety of materials including metals, alloys, ceramics, glasses and semiconductors. Containerless processing via ESL provides a high-purity environment for the study of high temperature materials and access to metastable states. Scientific topics investigated in the facility include nucleation, undercooling, metastable state formation and metallic glass formation. Additionally, the MSFC ESL provides data for the determination of phase diagrams, time-temperature-transition diagrams, viscosity, surface tension, density, heat capacity and creep resistance. In order to support a diverse research community, the MSFC ESL facility has developed a number of technical capabilities, including a portable system for in situ studies of structural tran$hrmations during processing at the high-energy X-ray beamline at the Advanced Photon Source of Argonne National Laboratory. The capabilities of the MSFC ESL facilities will be discussed and selected results of materials processing and characterization studies will be presented.

Rogers, Jan R.↗

NASA NTRS2012

The Exoplanet Microlensing Survey by the Proposed WFIRST Observatory

The New Worlds, New Horizons report released by the Astronomy and Astrophysics Decadal Survey Board in 2010 listed the Wide Field Infrared Survey Telescope (WFIRST) as the highest-priority large space mission for the . coming decade. This observatory will provide wide-field imaging and slitless spectroscopy at near infrared wavelengths. The scientific goals are to obtain a statistical census of exoplanets using gravitational microlensing. measure the expansion history of and the growth of structure in the Universe by multiple methods, and perform other astronomical surveys to be selected through a guest observer program. A Science Definition Team has been established to assist NASA in the development of a Design Reference Mission that accomplishes this diverse array of science programs with a single observatory. In this paper we present the current WFIRST payload concept and the expected capabilities for planet detection. The observatory. with science goals that are complimentary to the Kepler exoplanet transit mission, is designed to complete the statistical census of planetary systems in the Galaxy, from habitable Earth-mass planets to free floating planets, including analogs to all of the planets in our Solar System except Mercury. The exoplanet microlensing survey will observe for 500 days spanning 5 years. This long temporal baseline will enable the determination of the masses for most detected exoplanets down to 0.1 Earth masses.

Barry, Richard↗

NASA NTRS1995

AMCC casting development. Volume 1: Executive Summary

The Advanced Combustion Chamber Casting (AMCC) has been a technically challenging part due to its size, configuration, and alloy type. The height and weight of the wax pattern assembly necessitated the development of a hollow gating system to ensure structural integrity of the shell throughout the investment process. The complexity in the jacket area of the casting required the development of an innovative casting technology that PCC has termed 'TGC' or Thermal Gradient Control. This method, of setting up thermal gradients in the casting during solidification, represents a significant process improvement for PCC and has been successfully implemented on other programs. Metallurgical integrity of the final four castings was very good. Only the areas of the parts that utilized 'TGC Shape & Location System #2' showed any significant areas of microshrinkage when evaluated by non-destructive tests. Alumina oxides detected by FPI on the 'float' surfaces (top sid surfaces of the casting during solidification) of the part were almost entirely less than the acceptance criteria of .032 inches in diameter. Destructive chem mill of the castings was required to determine the effect of the process variables used during the processing of these last four parts (with the exception of the 'Shape & Location of TGC' variable).

Source record↗

NASA NTRS2015

Flexible Micropost Arrays for Shear Stress Measurement

Increased fuel costs, heightened environmental protection requirements, and noise abatement continue to place drag reduction at the forefront of aerospace research priorities. Unfortunately, shortfalls still exist in the fundamental understanding of boundary-layer airflow over aerodynamic surfaces, especially regarding drag arising from skin friction. For example, there is insufficient availability of instrumentation to adequately characterize complex flows with strong pressure gradients, heat transfer, wall mass flux, three-dimensionality, separation, shock waves, and transient phenomena. One example is the acoustic liner efficacy on aircraft engine nacelle walls. Active measurement of shear stress in boundary layer airflow would enable a better understanding of how aircraft structure and flight dynamics affect skin friction. Current shear stress measurement techniques suffer from reliability, complexity, and airflow disruption, thereby compromising resultant shear stress data. The state-of-the-art for shear stress sensing uses indirect or direct measurement techniques. Indirect measurements (e.g., hot-wire, heat flux gages, oil interferometry, laser Doppler anemometry, small scale pressure drag surfaces, i.e., fences) require intricate knowledge of the studied flow, restrictive instrument arrangements, large surface areas, flow disruption, or seeding material; with smaller, higher bandwidth probes under development. Direct measurements involve strain displacement of a sensor element and require no prior knowledge of the flow. Unfortunately, conventional "floating" recessed components for direct measurements are mm to cm in size. Whispering gallery mode devices and Fiber Bragg Gratings are examples of recent additions to this type of sensor with much smaller (m) sensor components. Direct detection techniques are often single point measurements and difficult to calibrate and implement in wind tunnel experiments. In addition, the wiring, packaging, and installation of delicate micro-electromechanical devices impede the use of most direct shear sensors. Similarly, the cavity required for sensing element displacement is sensitive to particulate obstruction. This work was focused on developing a shear stress sensor for use in subsonic wind tunnel test facilities applicable to an array of test configurations. The non-displacement shear sensors described here have minimal packaging requirements resulting in minimal or no disturbance of boundary layer flow. Compared to previous concepts, device installation could be simple with reduced cost and down-time. The novelty lies in the creation of low profile (nanoscale to 100 μm) micropost arrays that stay within the viscous sub-layer of the airflow. Aerodynamic forces, which are related to the surface shear stress, cause post deflection and optical property changes. Ultimately, a reliable, accurate shear stress sensor that does not disrupt the airflow has the potential to provide high value data for flow physics researchers, aerodynamicists, and aircraft manufacturers leading to greater flight efficiency arising from more in-depth knowledge on how aircraft design impacts near surface properties.

Wohl, Christopher J.↗

NASA NTRS1998

Geologic Landforms and Processes on Icy Satellites

During the first reconaissence of the satellites of the outer solar system conducted by the Voyager missions (1979-1989), a surprising diversity of unusual geologic landforms were observed, in some cases with bewildering complexity (e.g., Triton). Impact features were certainly expected but the variety of volcanic, diapiric, tectonic, impact, and erosional landforms was only remotely suggested by some early theoretical works. These diagnostic features are manifestations of the internal composition, thermal history, and dynamical evolution of these bodies. It is the job of the geologist to interpret the morphology, stratigraphy, and composition of these deposits and structures to ascertain what materials were mobilized in the interior, in what amount, and the mechanism and cause of their mobilization. In this chapter, we review what is know about these features and what constraints can be placed on composition and thermal history. Particular emphasis is placed on volcanic features, as these are most directly related to satellite composition and thermal history. The surface spectra, high albedos, and low bulk densities of the satellites of the outer solar system indicate that water and other ices are abundant on these bodies, particularly on their surfaces. Ices, particularly water ice, are less dense than silicates and will tend to float and form crusts during differentiation or partial melting of the interior. Ices therefore take the place of silicates as 'crust-forming' minerals and dominate geologic processes on icy satellites. Melted ices form magma bodies, and sometimes are extruded as lavas, an unusual but still valid perspective for terrestrial geologists. The unusual properties of some ices, including their low melting temperatures, and low strengths (as well as the decrease in density on the freezing of water ice), will ultimately be very important in interpreting this record.

Schenk, Paul M.↗