Search NASA⌕ Search

SEARCH · Search NASA

Results for “mechanical performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Influence of weave architecture on mechanical response of SiC f -SiC m tubular composites

Due to their high resistance to radiation damage and elevated temperature, silicon carbide fiber-reinforced, silicon carbide matrix composites (SiC f -SiC m ) are identified as potential cladding structures for use in nuclear reactors. In this study, four composite architectures with varying ply numbers along the thickness direction and different biaxial or triaxial plain weave orientations at either 45° or 60°, were systematically evaluated under various stress states to assess the influence of weave architecture on mechanical performance. Experiments were conducted on SiC f -SiC m composite tubes under tensile hoop, axial compression, and rotating flexural loading to evaluate the mechanical response and investigate the failure modes using high-speed imaging and digital image correlation (DIC) techniques. It was found that for tensile hoop burst and flexural loading, the braiding angle had the most significant influence on the strength of the composite, whereas the effect of fiber angle was more limited for compression testing. Under axial compression a unique failure mode where a microcrack nucleates and grows only to a length equal to the thickness of a single yarn was identified. This crack growth behavior is reflected as periodic oscillations in the load-displacement response. For both axial and hoop loading, regardless of weave angle and number of plies, failure always initiated parallel to the tube axis in a single yarn and the cumulative interaction of these microcracks lead to either axial burst or fracture at an angle to the tube axis along a yarn. Furthermore, these results point to the importance of customizing the design of tube architecture for enhanced performance in specified nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology

Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Additive Manufacturing of Lightweight Structures: Microfibrillated Cellulose – PLA Biofoams

Extrusion-based polymer additive manufacturing (AM) technology is growing rapidly. The introduction of fiber reinforced feedstock materials and recent developments in the manufacturing systems have promulgated large scale AM of composites to create new industries and applications. Synthetic fibers such as carbon and glass fibers are commonly used to reinforce polymer composites. However, increasing environmental and long-term sustainability concerns are leading to new materials using cellulose fiber reinforcement in bio-derived polymers. These materials offer new property sets, new supply chains and have the potential to provide economical solutions leading to new applications. Large scale AM can be attractive for many different applications because of its ability to freeform manufacture complex geometries; each application may require different material properties. One of the novel application areas for large scale AM is 3D printing of lightweight materials via foaming. Although achieving low density is the key in light weighting via foaming, mechanical performance is also important for many applications. In this study the impact of micro-cellulose fibers (MFC) on foaming behavior and the mechanical properties of additively manufactured parts is investigated. MFC-polylactic acid (PLA) feedstock pellets were prepared at varying MFC content (5, 10, 15 and 20 wt.%) to understand the impact of cellulose fiber content on density and mechanical properties of the AM biocomposites. Also, the impact of extrusion speed and foaming agent content on the AM biocomposites is investigated. Although achieving uniform printed foam structure is challenging with the presence of cellulose fibers, promising results were accomplished with density values below 0.5g/cm3.

Tekinalp, Halil↗
DOE OSTI2020

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate–modified MFC improved the tensile strength by 38 % and Young’s modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. We find that the method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Physically-Based Model for Thermo-Oxidative and Hydrolytic Aging of Elastomers

A computationally efficient model is proposed to capture the loss of mechanical performance due to chemical aging that are formed as the competition of chain scission and cross-link formation/dissolution, such as thermo-oxidative aging or hydrolytic aging. The model should be considered an extension of our recent models [1, 2, 3] which further simplifies the matrix behavior based on the assumption of independence of environmental and mechanical damage. The model uses this assumption to reduce the necessary material parameters needed to model constitutive and inelastic behavior of elastomers during aging. To this end, the model can provide accurate predictions of the material performance with the significantly fewer number of fitting parameters. The model is relevant for all decay mechanisms formed by the occurrence of two simultaneous micro-mechanisms; (i) formation/reduction of the cross-links, and (ii) chain scission, both of which are present in thermo-oxidation and hydrolytic aging. Assuming the alteration of the chain density along the aging trajectory is identical to the peroxide cross-link density for thermo-oxidation, and the change of the average molecular weight for hydrolysis, the strain energy of polymer matrix can be rewritten as a function of deformation, deformation history, storage time and aging temperature. Next, the modified network alteration model is formulated for implementation into Finite Element (FE) simulations. The model is built on the presumption of homogeneous and consistent oxygen/water absorption and thus is mainly relevant for relatively thin samples exposed to environmental loads for a long time. The proposed model includes only six physically inspired material parameters. Therefore, while it is computationally efficient, it shows good agreement with own experimental data, which performed on various range of accelerated aging temperatures and times. With respect to its computational efficiency, simplicity, accuracy, and interpret-ability, the model is the right choice for advanced implementations in FE programs.

42 ENGINEERING↗
DOE OSTI2024

Hydrogen Effects on Cladding Performance during Simulated Loss of Coolant Accident Testing

Fresh Zircaloy cladding segments were charged with hydrogen and subjected to simulated Loss of Coolant Accident (LOCA) conditions to assess the impact of hydrogen on the cladding mechanical performance and rupture resistance. The cladding rupture temperature decreased by 10 °C for every 100 wppm H added into the system for two different internal pressurization cases. Post-test analysis showed a loss of ductility with increasing hydrogen content, evident through decreased balloon sizes, smaller rupture openings, and sharper rupture interfaces. Digital image correlation was used to map the cladding strain in situ for two cladding segments. An elevated intermediate temperature uniform strain was visible for the hydride cladding, occurring prior to the decreased ductility during balloon and rupture determined from posttest fractography and microscopy. The thermal stability of Zr alloys as a function of hydrogen concentration and the thermal stability of Zr hydride as a function of temperature are likely responsible for the uniform deformation behavior at intermediate temperatures. The present framework for rapid assessment of hydrogen effects on cladding rupture can be utilized as an initial comparison to high burnup cladding thermomechanical response to a LOCA, where local regions may contain high concentrations of precipitated Zr hydride phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Hydrogen Effects on Cladding Performance during Simulated Loss of Coolant Accident Testing

Fresh Zircaloy cladding segments were charged with hydrogen and subjected to simulated Loss of Coolant Accident (LOCA) conditions to assess the impact of hydrogen on the cladding mechanical performance and rupture resistance. The cladding rupture temperature decreased by 10 °C for every 100 wppm H added into the system for two different internal pressurization cases. Post-test analysis showed a loss of ductility with increasing hydrogen content, evident through decreased balloon sizes, smaller rupture openings, and sharper rupture interfaces. Digital image correlation was used to map the cladding strain in situ for two cladding segments. An elevated intermediate temperature uniform strain was visible for the hydride cladding, occurring prior to the decreased ductility during balloon and rupture determined from posttest fractography and microscopy. The thermal stability of Zr alloys as a function of hydrogen concentration and the thermal stability of Zr hydride as a function of temperature are likely responsible for the uniform deformation behavior at intermediate temperatures. The present framework for rapid assessment of hydrogen effects on cladding rupture can be utilized as an initial comparison to high burnup cladding thermomechanical response to a LOCA, where local regions may contain high concentrations of precipitated Zr hydride phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Framework for Characterizing the Performance of High-Early Strength, High-Volume Fly Ash (HVFA) Concrete Structures

This presentation will highlight the development of a comprehensive framework to characterize the performance of high-volume fly ash (HVFA) concretes at early ages and discuss the resulting implications for concrete structures built using such materials. Achieving high-early compressive and/or flexural strength is often of particular importance for precast and/or prestressed concrete components – due to early age loading demands resulting from lifting, handling, or application of initial prestress – or other types of concrete structures that can significantly benefit from rapid strength development - such as for bridge deck repairs. The framework first includes a methodology for optimizing the strength of HVFA cementitious binders before subsequently scaling up the technology to evaluation of fresh and hardened HVFA concrete performance. A series of trial mix designs will be presented to demonstrate the effectiveness of the framework to achieve not only the desired high-early strength targets but also satisfactory workability, often in the form of self-consolidating concrete. Mechanical performance was evaluated at several age-dependent milestones and, in conjunction with estimating concrete strength using the maturity method, was ultimately used to facilitate the development of novel strength development history curves. By way of these datasets, concrete mechanical properties were utilized in the design of prototype structural components, such as beams and wall panels, for subjection to larger-scale experimental testing. Implications for other pertinent HVFA concrete performance attributes, such as shrinkage or creep, will also be discussed. The framework also includes a comprehensive methodology for evaluating the environmental life-cycle performance of HVFA concrete structures focused on mitigating any unwarranted environmental consequences resulting from beneficial HVFA reuse in concrete. Strategies for more widespread implementation of HVFA concrete materials into construction practice will also be presented. Lastly, the role of the HVFA concrete framework towards the development of new provisions for building codes and/or design standards, and recommendations for future research needs will also be discussed.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Modular Processing of Flare Gas for Carbon Nanoproducts

This project demonstrated the technical viability and economic promise of a modular system for converting flared natural gas into valuable carbon nanoproducts (CNPs) through catalytic chemical vapor deposition (CVD). All major project milestones were successfully completed, including reactor design and commissioning, catalyst development, process optimization, technoeconomic analysis, and application testing in concrete systems. The overarching goal was to create a scalable, field-deployable process that valorizes stranded methane by producing high-value carbon materials for use in cementitious composites. At the lab scale, the team designed and built a fluidized bed reactor optimized for use with silica fume-supported nickel catalysts synthesized via atomic layer deposition (ALD). A statistically designed sintering study enabled precise tuning of nickel nanoparticle size, identifying the influence of oxygen partial pressure, time, and temperature on catalyst morphology and performance. These insights allowed the team to target catalyst conditions that maximize carbon nanofilament growth. Subsequent CVD experiments achieved up to 31.8 wt% carbon deposition under optimized conditions, with TEM confirming the presence of nanofilament structures and sustained hydrogen evolution during reaction. Reactor upgrades and empirical fluidization studies supported the development of reliable, repeatable experimental protocols. The modular pilot-scale skid reactor was fully constructed, instrumented, and commissioned. Capable of operating at 675–800°C and pressures up to 290 psig, the system was designed for continuous operation at a carbon production rate of 1 kg/hr. Initial demonstration runs confirmed solids handling, thermal control, and system leak-tightness, although a critical reactor component (the downfeed tube) was inadvertently omitted during final assembly. This omission limited gas–solid contact and prevented meaningful carbon deposition during pilot-scale CVD runs. Nonetheless, the system operated safely under design conditions, and the root cause of performance limitations was clearly identified. Complementary work on UHPC formulations demonstrated that small additions of carbon nanoproducts, including those derived from flare gas, can significantly enhance mechanical performance while preserving workability. A comprehensive study of CNF dispersion techniques and mix design optimization led to a clear protocol for integrating these nanomaterials into concrete. Incorporation of CNPs improved flexural toughness and reduced porosity, supporting their use in high-performance infrastructure applications. A technoeconomic analysis (TEA) confirmed that this process can produce CNP-loaded catalyst material at a levelized cost below $\$$7/kg across a range of catalyst loadings and reaction yields. With estimated market values for the carbon composite product ranging from $\$$14 to over $\$$60/kg, and the ability to blend CNPs into concrete at sub-percent levels with less than 10% added cost, the system presents a compelling economic case. While additional engineering work is needed to optimize fluidization and heat transfer at scale, this project establishes a strong foundation for commercial development. The process is not only technically sound but also economically promising, representing a viable pathway for flare gas mitigation through modular carbon nanomaterial production.

03 NATURAL GAS↗
DOE OSTI2022

A New Perspective of Post-Weld Baking Effect on Al-Steel Resistance Spot Weld Properties through Machine Learning and Finite Element Modeling

The root cause of post-weld baking on the mechanical performance of Al-steel dissimilar resistance spot welds (RSWs) has been determined by machine learning (ML) and finite element modeling (FEM) in this study. A deep neural network (DNN) model was constructed to associate the spot weld performance with the joint attributes, stacking materials, and other conditions, using a comprehensive experimental dataset. The DNN model positively identified that the post-weld baking reduces the joint performance, and the extent of degradation depends on the thickness of stacking materials. A three-dimensional finite element (FE) model was then used to investigate the root cause and the mechanism of the baking effect. It revealed that the formation of high thermal stresses during baking, from the mismatch of thermal expansion between steel and Al alloy, causes damage and cracking of the brittle intermetallic compound (IMC) formed at the interface of the weld nugget during welding. This in turn reduces the joint performance by promoting undesirable interfacial fracture when the welds were subjected to externally applied loads. The FEM model further revealed that increase in structural stiffness, because of increase in steel sheet thickness, reduces the thermal stresses at the interface caused by the thermal expansion mismatch and consequently lessens the detrimental effect of post-weld baking on the joint performance.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Harnessing biomass-derived reinforcements for sustainable flame-resistant composite

Bio-based composites containing natural fiber reinforcements have been integral to developing innovative, low-cost, and low-energy technologies for transportation applications in marine, automotive, and other industries. The low density of natural fibers gives these materials a high specific stiffness and strength, which can lead to significant weight savings in composites. This study focused on a specialty type of wood fiber treated with boric acid (≤ 7%) sourced from Northern White Pine in the USA, marketed as TimberFill. TimberFill is a high aspect ratio, fibrillated wood fiber that is produced commercially for wood fiber insulation; it is chemically treated to improve both its flame retardance and water resistance. In the present study, TimberFill was processed into non-woven mats using a process akin to papermaking and then infiltrated with epoxy resin. Biochar from wood waste was also incorporated into the epoxy resin as a low-cost filler and functional additive. The effects of biochar concentration on composites’ flame retardance (17% improvement in burn rate), thermal conductivity (improved by 9%), and mechanical performance (33% improvement in modulus) are herein presented. Additionally, it explores the plasticizing effect of the boric acid used in the treatment of TimberFill on the thermal and mechanical properties of the resulting composites, specifically on the thermal expansion coefficient.

Joshy, Joslin [ORNL]↗
DOE OSTI2024

Low-Cost, High-Performance Carbon Fiber for Compressed Natural Gas Storage Tanks (Final Technical Report – Down Select Report)

The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.

08 HYDROGEN↗
DOE OSTI2022

Mechanical behavior of bimetallic stainless steel and gray cast iron repairs via directed energy deposition additive manufacturing

The utility of gray cast iron in engine components remains tied to the mechanical performance and cost. Repair and remanufacturing of castings offer economical and sustainable benefits; however, high thermal input from traditional fusion-based welding is unable to restore the original mechanical quality owing to brittle microstructures and porosity formed in situ. Directed energy deposition (DED) is an additive manufacturing method that has received considerable interest for repairs owing to the highly controllable nature of the process. Despite this, few works have connected the effect of DED parameters on actual interfacial strength. Consequently, distinct DED parameter combinations were identified to maximize the strength and fatigue life of the repaired cast iron. Further, high speed melt pool imaging and residual stress measurements are provided to aid in the understanding of the metallurgical quality and strength seen in these structures. In general, higher scanning speeds and lower thermal gradients promoted comparable tensile strength to that of the original gray cast iron. The results presented here provide a foundation to tune in the DED process to generate the required mechanical quality as a starting point for future process advancements.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Designing Recyclable Biomass-Based Polyesters (Final Technical Report)

This project successfully demonstrated the production of sustainable polyesters from biomass-derived monomers, offering properties on par with or superior to fossil-based plastics such as LLDPE and PBAT. Using renewable chemical platforms like furfural and HMF, we synthesized over eight novel monomers and nearly 100 aliphatic-aromatic polyesters. Among these, PPeAT and PDDF emerged as highly promising candidates for flexible packaging applications, exhibiting excellent mechanical performance, tunable thermal properties, and enhanced barrier characteristics. Key advances included the development of ring-opening polymerization strategies using cyclic monomer intermediates to produce high molecular weight materials with excellent control. The resulting polymers achieved biobased content of at least 44 wt.%. We also implemented chemical recycling via catalytic methanolysis, recovering over 90% of monomers from PPeAT at semi-pilot scale. This supports a circular economy approach by enabling material reuse without performance loss. Techno-economic and life cycle assessments confirmed that these polyesters can reduce greenhouse gas emissions by up to 50% compared to petroleum-derived alternatives. Favorable mechanical properties may further reduce material demand, and cost competitiveness was demonstrated under specific market conditions. Feedstock cost and environmental footprint were identified as primary levers for future optimization. In summary, the project met or closely approached all technical targets, including biodegradability, strength, and processing compatibility. While minor issues such as color and melting point variation remain, the results strongly support continued development and scale-up of these sustainable materials.

09 BIOMASS FUELS↗
DOE OSTI2026

A LASER POWDER BED FUSION ADDITIVE MANUFACTURING CHARACTERIZATION APPROACH AND DATASET HIGHLIGHTING IMPLICATIONS FOR CROSS-PLATFORM PERFORMANCE CONSISTENCY

Additive Manufacturing (AM) has remained a rapidly growing technology over the past decade, which affords many benefits. However, there is one main hinderance to widespread adoption: Products produced on one Laser Powder Bed Fusion (LPBF) AM system can vary in mechanical performance from those produced on another system. This is due to the fact that while LPBF AM system is producing a product’s shape, it is also producing the product’s material. Due to the complex and dynamic nature of LPBF, items fabricated on one system can be different in terms of dimensions, microstructure and quality compared to items fabricated on a different make or model system. This lack of cross-platform performance consistency makes widespread adoption challenging. This work was created to help understand the variation between different Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM) systems across different manufacturers, models, and users, and to provide insight into how to ensure product consistency regardless of system selection.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Creep-Resistant Ferritic-Martensitic Steels for Power Plant Applications

Creep-resistant ferritic-martensitic steels are essential materials used in power plants for electricity generation. The efficiency and emissions of the plant are closely related to the operating temperature. Materials used in the hottest sections are one of the main limiting factor for plant operation at 650 °C. This review describes the recent development of creep-resistant ferritic-martensitic steels from a large dataset of in-house research. The findings are tied to available literature for discussion. A first steel, CPJ-7, was developed with an operating temperature approaching 650 °C, and a refined design, JMP, showed the potential to operate at 650 °C. Approximately fifty different ingots, each weighing ~ 7 kg, were vacuum induction melted and processed. Overall, wrought and cast versions of CPJ-7 present superior creep properties when compared to wrought and cast versions of COST alloys for steam turbine and P91/92 for boiler applications. The prolonged creep life was attributed to slowing down the process of the destabilization of the MX and M 23 C 6 precipitates at 650 °C. The cast version of CPJ-7 also revealed superior mechanical performance, above commercially available cast 9% Cr martensitic steel or derivatives. Following the work on CPJ-7, the JMP steels were designed with higher Co for increased solid solution strengthening, Si for oxidation resistance and increased W for matrix strength and stability. The JMP steels showed increases in creep life compared to CPJ-7 between 118 and 150% at 650 °C for testing at various stresses between 138 and 207 MPa. On a Larson–Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN steel. The influence of various elements within the composition of the alloys on the microstructure and mechanical properties is discussed. This review presents approximately 420,000 h of in-house creep testing, the equivalent of almost 50 years of cumulative creep tests.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Toolpath Optimization of Polymer Composite Additive Manufacturing AM Printed Mold to Improve Performance for Compression Molding Applications

This study explores the optimization of toolpaths for short fiber polymer composite additive manufacturing (AM) printed molds in compression molding applications, an emerging trend driven by advancements in 3D printing technology. AM printed molds offer reduced tooling costs and greater design flexibility, particularly for prototyping and low-volume production. The proposed optimization approach evaluates mold performance using two key metrics: deformation and shape accuracy. Multiple toolpaths are generated, and finite element (FE) simulations capture fiber orientation and material properties, which are then integrated into a mechanical performance model. Shape accuracy is assessed by comparing the deformed mold shape with the original using surface normals as a descriptor. The analysis identifies the toolpath that delivers the best overall performance, establishing it as the most suitable option for achieving optimal mold characteristics in compression molding applications.

Limaye, Madhura [ORNL]↗
DOE OSTI2025

Mineralized sclerites in the gorgonian coral Leptogorgia chilensis as a natural jamming system

The soft corals (Cnidaria, Octocorallia), a diverse group of colonial marine invertebrates, can reversibly tune their body stiffness in response to external stimuli. This capability is attributed to their dynamic skeletal systems, which consist of thousands of mineralized skeletal elements, called sclerites, embedded within a gel-like matrix that swells/deswells and unjams/jams the sclerites, thus modulating skeletal stiffness. While sclerite morphology is widely used for species identification, its role in the mechanical performance of a soft coral’s skeletal system is largely unknown. Here, we investigated structure-jamming relationships in sclerite-based skeletal architectures using the red gorgonian octocoral Leptogorgia chilensis as a model system. The sclerites of L. chilensis exhibit a shaft-like geometry with two axial branches and two sets of triradiate side branches, which are aligned with the crystallographic symmetry of the constituent magnesium-containing calcite. By combining multiscale three-dimensional (3D) structural characterization, parametric geometrical modeling, 3D printing, mechanical testing, and discrete element simulations, we demonstrate how sclerite geometry achieves a balanced jamming performance in terms of stiffness, weight, strength, and fracture resistance in comparison to alternative geometries parametrically modified from the native sclerites (e.g., changes in the length and number of side branches). Here, we also found that these performance metrics are achieved through the effective interlocking among side and axial branches, which is further enhanced by the fractal-like microscopic spikes on the branch tips. The findings in this natural jamming system offer insights for designing synthetic mechanotunable material architectures for a wide range of applications, from soft robotics to mechanical dampeners.

36 MATERIALS SCIENCE↗