Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Corrosion Behavior of Pipeline Steel with Different Microstructures Under AC Interference in Acid Soil Simulation Solution

Corrosion behavior of X65 pipeline steels with different microstructures under alternating current (AC) interference was investigated in acid soil simulation solution by potentiodynamic polarization curve, potentiostatic polarization curve and immersion test. The results show that superimposed AC causes a sharp increase in corrosion current density of X65 steel. With the increase in i{sub AC}, the corrosion current densities of steels with various microstructures increase, especially at high i{sub AC}. Hot-rolled steel mainly experiences uniform corrosion, with very slight pit corrosion. Serious corrosion degrees with intensive corrosion pits can be observed on the surfaces of normalized and quenched microstructure steels. The annealed steel exhibits the feature of non-uniform corrosion with some pitting. The steels with various microstructures applied with AC have different corrosion resistance. The normalized steel shows the worst corrosion resistance, then the quenched microstructure, and the hot-rolled steel displays the optimum corrosion resistance. The difference in the microstructure can result in difference in corrosion degree and occurrence position of pitting corrosion of X65 steel. The normalized microstructure composed of polygonal ferrite and a large amount of pearlite and bainite is the most susceptible to AC corrosion.

36 MATERIALS SCIENCE↗

Three-dimensional phase field sintering simulations accounting for the rigid-body motion of individual grains

Sintering is a widely used powder processing technique in industrial applications. During sintering, atoms migrate to decrease the energy of the system via two main mechanisms: coarsening and densification, both of which lead to significant morphological variation of the sintered microstructure. When simulating sintering dynamics, the phase-field method has been broadly utilized because of its convenience in tracking morphology evolution. When a large number of grains is involved, it is common to use the same order parameter to describe multiple grains that are not in direct contact with one another (in order to reduce the computational memory demands). However, with this treatment it is difficult to handle the rigid-body motion of individual grains during densification. In this work, an implementation scheme is introduced to overcome the challenge of calculating individual particle motion based on existing equations. It uses a grouping algorithm and sets a cutoff radius on each grain for calculating the particle velocity during densification. This method allows for the incorporation of the densification mechanism, which has been commonly ignored in previous work, into phase-field sintering models in three-dimensional simulations with a large number of particles/grains. Moreover, through combination with the smoothed boundary method, material properties of sintered microstructures, such as the effective diffusivity and Young’s modulus, can be calculated during the sintering processes.

36 MATERIALS SCIENCE↗

Simulation of Creep Deformation and Failure in Graded AM Microstructures

This report describes modeling tools and techniques developed to simulate the long-term material performance of 316H stainless steel manufactured using Laser Powder Bed Fusion (LPBF). A physics-based Crystal Plasticity Finite Element model is used to simulate creep in microstructures and to study the roles of grain morphology, porosity, and texture. We describe our modeling methodology, including an orientation-mapping technique to capture the spatially varying crystallographic orientation that results from the build conditions. Our study of microstructural features shows that AM microstructures produced by LPBF tend to creep faster in the build direction, while texture and grain boundaries strengthen the transverse directions. However, when grain-boundary porosity and the consequent cavity growth are included in the model, the transverse directions begin to creep faster. In examining texture, the results indicate that spatially varying orientation arising from the build conditions increases anisotropy in the material, making it critical to account for orientation gradients in the material to accurately model its mechanical behavior. We also describe a material-model calibration campaign in which we calibrated the constitutive model specifically for LPBF 316H stainless steel at 725℃ for both solution-annealed and as-built conditions. Finally, these tools and techniques are used to model creep in microstructures representing different regions of an LPBF material with graded microstructure, owing to intentional variation in processing conditions. The creep simulation results show good agreement with experimental data across all three microstructures, with future work planned to study rupture in the material.

36 MATERIALS SCIENCE↗

Reduced-order model for microstructure evolution prediction in the electrodes of solid oxide fuel cell with dynamic discrepancy reduced modeling

Microstructure evolution in the electrodes of solid oxide fuel cell is an important degradation mechanism which reduces active sites for redox reaction and the electric conductivity. Phase field models for microstructure evolution simulation are usually expensive for large scale simulations. In this paper, a reduced-order coarsening model is developed using dynamic discrepancy reduced modeling, which reduces the model order by inserting Gaussian process stochastic functions into the dynamic equations of Ostwald ripening. The reduced order model has been calibrated on a dataset generated by a phase field model that has been well validated to experiments. A validating dataset has also been generated with which the model prediction show good agreement. This model is further applied to predict long term microstructure evolution in different SOFC electrodes. Finally, this work is the first attempt of building a degradation model of SOFC using data science techniques.

36 MATERIALS SCIENCE↗

A Mechanism-based Model for Deformation Twinning in Polycrystalline FCC Steel

Deformation twinning, a common and important plastic deformation mechanism, is the key contributor to the excellent combination of strength and ductility in twinning-induced plasticity (TWIP) steel. In the open literature, a significant amount of research has been reported on the microstructural characteristics of deformation twinning and its influence on the overall deformation behavior of TWIP steel. In this study, we examine the feasibility of a mechanism-based crystal plasticity model in simulating the microstructural level deformation characteristics of TWIP steel. To this end, a model considering both double-slip and double-twin is developed to investigate the stress-strain behavior and local microstructural features related to the formation and growth of micro-twins in low stacking fault energy (SFE) TWIP steel. The twin systems are described as pseudo-slips that can be activated when their resolved shear stress reaches the corresponding critical value. A hardening law that accounts for the interaction among the slip and twin systems is also developed. Numerical simulations for dDifferent mesh sizes and single crystal patch tests under different loading modes are carried out to verify the modeling procedure. Our simulation results reveal that, despite its simple nature, the double-slip/double-twin model can capture the key deformation features of TWIP steel, including twin volume fraction evolution, continuous strain hardening, and the final fracture in the form of strain localization.

Environmental Molecular Sciences Laboratory↗

Connect microstructure evolution to property degradation with validated simulation

Reliable material performance is required for plasma-facing material (PFM) candidates. Previous research has shown that plasma and neutron radiation exposure induces microstructural changes in PFMs; changes in thermal and electrical conductivities and in material hardening and embrittlement were also observed after neutron irradiation. These material property changes will negatively impact the performance of the PFMs in a fusion reactor. Despite the well-known connection between material microstructure, properties, and performance, there is a need for validated modeling capabilities connecting PFM property degradation with microstructural evolution under fusion-relevant conditions. We are developing a simulation capability to couple plasma-induced microstructural evolution to material property degradation. Our approach relies on deliberate mapping between individual simulation models and experimental characterization for validation. The open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) software was used for this simulation capability development. A MOOSE phase-field model was coupled with the cluster dynamics code, Xolotl, to predict microstructural evolution. Microstructure characterization techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), and laser scanning confocal microscopy (LSCM) are used to validate these microstructural evolution simulations. Calculation of thermal and electrical conductivities with first principles simulations was performed for bulk material and for grain boundaries; these results are used within MOOSE models to calculate effective thermal and electrical conductivities as a function of grain characteristics. Thermoreflectance and four-probe techniques were employed to measure the thermal and electrical conductivities, respectively. A MOOSE crystal plasticity model was adapted to predict microstructure-sensitive deformation behavior, and X-ray diffraction (XRD) was used to collect bulk dislocation density data for validation. After individual simulation validation, these models are coupled to predict material property changes resulting from plasma exposure. We focused here on an experimental design to emphasize the separate effects of moderate thermal loads and plasma exposure using tungsten. Annealing of tungsten was performed under a protective environment for temperatures ranging from 500$^o$C to 1500$^o$C. The plasma exposure was completed in the Tritium Plasma Experiment at Idaho National Laboratory under a deuterium flux of 1e22 $\frac{D}{m^2s}$. This incremental approach is employed to build confidence in the modeling capability: separate-effects tests ensure that the models capture key mechanisms from single environmental conditions before predicting PFM property degradation under combined loads. We will show our early results from coupling these simulation models to predict PFM property changes from microstructural evolution. Comparisons of the simulation results with preliminary validation data will be discussed.

36 - MATERIALS SCIENCE↗

Three-dimensional in Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions in polycrystalline samples containing several grains with a small misorientation with respect to the temperature gradient. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions that shed new light on the role of subgrain boundaries in the spatiotemporal evolution of the primary cellular spacing and the selection of dendritic array structures.

Kaihua Ji↗

Diffuse-interface model for smoothed particle hydrodynamics

Diffuse-interface theory provides a foundation for the modeling and simulation of microstructure evolution in a very wide range of materials, and for the tracking/capturing of dynamic interfaces between different materials on larger scales. Smoothed particle hydrodynamics (SPH) is also widely used to simulate fluids and solids that are subjected to large deformations and have complex dynamic boundaries and/or interfaces, but no explicit interface tracking/capturing is required, even when topological changes such as fragmentation and coalescence occur, because of its Lagrangian particle nature. Here we developed an SPH model for single-two component singletwo- phase fluids that is based on diffuse-interface theory. In the model, the interface has a finite thickness and a surface tension that depend on the coefficient, k, of the gradient contribution to the Helmholtz free energy functional and the density dependent homogeneous free energy. In this model, there is no need to locate the surface (or interface) or to compute the curvature at and near the interface. One- and two-dimensional SPH simulations were used to validate the model.

97 MATHEMATICS AND COMPUTING↗

A New Efficient Quantitative Multi-component Phase Field: Lattice Boltzmann Model for Simulating Ti6Al4V Solidified Dendrite Under Forced Flow

Ti6Al4V is a widely used, multi-component alloy in additive manufacturing, during which the fluid flow in the molten pool significantly affects the solidified dendrites. To predict and further control the microstructure, modeling and simulating the microstructure evolution play a critical role. In this study, a newly developed, efficient, quantitative multi-component phase-field (PF) model is coupled with a lattice Boltzmann (LB) model to simulate Ti6Al4V solidified dendrite evolution under fluid flow. The accuracy and convergence behavior of the model is validated by the Gibbs–Thomson relation at the dendrite tip. Single and multiple two-dimensional (2D) equiaxed dendrite evolution cases under forced flow were simulated. Results show that the dendrite pattern is influenced remarkably by the fluid flow. Underlying mechanisms of the asymmetrical evolution are revealed by discussing the interaction among the flow, composition distribution and dendrite morphology, quantitatively. The dendrite kinetics are also derived, which ascertains the relationship between tip velocity and undercooling and inlet velocity and is the foundation for larger-scale simulation. We believe that the coupled quantitative multi-component PF–LB framework employed in this study helps in investigating the solidified dendrite morphology evolution in a deep and quantitate manner.

36 MATERIALS SCIENCE↗

Multiphysics and Multiscale Modeling of Coupled Transport of Chloride Ions in Concrete

Chloride ions (Cl−)-induced corrosion is one of the main degradation mechanisms in reinforced concrete (RC) structures. In most situations, the degradation initiates with the transport of Cl− from the surface of the concrete towards the reinforcing steel. The accumulation of Cl− at the steel-concrete interface could initiate reinforcement corrosion once a threshold Cl− concentration is achieved. An accurate numerical model of the Cl− transport in concrete is required to predict the corrosion initiation in RC structures. However, existing numerical models lack a representation of the heterogenous concrete microstructure resulting from the varying environmental conditions and the indirect effect of time dependent temperature and relative humidity (RH) on the water adsorption and Cl− binding isotherms. In this study, a numerical model is developed to study the coupled transport of Cl− with heat, RH and oxygen (O2) into the concrete. The modeling of the concrete microstructure is performed using the Virtual Cement and Concrete Testing Laboratory (VCCTL) code developed by the U.S. National Institute of Standards and Technology (NIST). The concept of equivalent maturation time is utilized to eliminate the limitation of simulating concrete microstructure using VCCTL in specific environmental conditions such as adiabatic. Thus, a time-dependent concrete microstructure, which depends on the hydration reactions coupled with the temperature and RH of the environment, is achieved to study the Cl− transport. Additionally, Cl− binding isotherms, which are a function of the pH of the concrete pore solution, Cl− concentration, and weight fraction of mono-sulfate aluminate (AFm) and calcium-silicate-hydrate (C-S-H), obtained from an experimental study by the same authors are utilized to account for the Cl− binding of cement hydration products. The temperature dependent RH diffusion was considered to account for the transport of Cl− with moisture transport. The temperature and RH diffusion in the concrete domain, composite theory, and Cl− binding and water adsorption isotherms are used in combination, to estimate the ensuing Cl− diffusion field within the concrete. The coupled transport process of heat, RH, Cl−, and O2 is implemented in the Multiphysics Object-Oriented Simulation Environment (MOOSE) developed by the U.S. Idaho National Laboratory (INL). The model was verified and validated using data from multiple experimental studies with different concrete mixture proportions, curing durations, and environmental conditions. Additionally, a sensitivity analysis was performed to identify that the water-to-cement (w/c) ratio, the exposure duration, the boundary conditions: temperature, RH, surface Cl− concentration, Cl− diffusion coefficient in the capillary water, and the critical RH are the important parameters that govern the Cl− transport in RC structures. In a case study, the capabilities of the developed numerical model are demonstrated by studying the complex 2D diffusion of Cl− in a RC beam located in two different climatic regions: warm and humid weather in Galveston, Texas, and cold and dry weather in North Minnesota, Minnesota, subjected to time varying temperature, RH, and surface Cl− concentrations.

composite theory↗

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗

A Stochastic Reduced-Order Model for Statistical Microstructure Descriptors Evolution

Integrated computational materials engineering (ICME) models have been a crucial building block for modern materials development, relieving heavy reliance on experiments and significantly accelerating the materials design process. However, ICME models are also computationally expensive, particularly with respect to time integration for dynamics, which hinders the ability to study statistical ensembles and thermodynamic properties of large systems for long time scales. To alleviate the computational bottleneck, we propose to model the evolution of statistical microstructure descriptors as a continuous-time stochastic process using a non-linear Langevin equation, where the probability density function (PDF) of the statistical microstructure descriptors, which are also the quantities of interests (QoIs), is modeled by the Fokker–Planck equation. In this work, we discuss how to calibrate the drift and diffusion terms of the Fokker–Planck equation from the theoretical and computational perspectives. The calibrated Fokker–Planck equation can be used as a stochastic reduced-order model to simulate the microstructure evolution of statistical microstructure descriptors PDF. Considering statistical microstructure descriptors in the microstructure evolution as QoIs, we demonstrate our proposed methodology in three integrated computational materials engineering (ICME) models: kinetic Monte Carlo, phase field, and molecular dynamics simulations.

97 MATHEMATICS AND COMPUTING↗

Model-informed, Adaptive Physical Vapor Deposition to Fabricate Hierarchical Binary-alloy Thin-films

Designing next generation thin films, tailor-made for specific applications, relies on the availability of robust processing-structure-property relationships. Traditional structure zone diagrams are limited to low-dimensional mappings, with machine-learning methods only recently attempting to relate multiple processing parameters to the final microstructure. Despite this progress, structure-processing relationships are unknown for processing conditions that vary during thin-film deposition, limiting the range of microstructures and properties achievable. In this project, we employed a phase-field computational model combined with a genetic algorithm (GA) to identify and design time-dependent processing protocols that achieve tailor-made microstructures. We simulate the physical vapor deposition of a binary-alloy thin film by employing a phase-field model, where deposition rates and diffusivities are controlled via the genetic algorithm. Our GA-guided protocols achieve targeted microstructures with lateral and vertical concentration modulations, as well as more complex, hierarchical microstructures previously not described in simple structure zone diagrams. Our algorithm provides insight to experimentalists looking for additional avenues to design novel thin-film microstructures.

36 MATERIALS SCIENCE↗

Effect of microstructure on fatigue crack propagation in additive manufactured nickel-based superalloy Haynes 282: an experiment and crystal plasticity study

Haynes 282 is a γ' precipitation-strengthened nickel-based superalloy known for its exceptional high-temperature creep resistance and excellent fabricability. Recent advancements in powder-bed fusion-based additive manufacturing (PBF-AM) have enabled the fabrication of Haynes 282 with accurate, site-specific control of the grain orientation and morphology at the microscale. This ability opens up new avenues for microstructure design, to improve the material’s fatigue crack resistance and service life. This paper investigates the fatigue crack growth behavior of hybrid microstructure Haynes 282 fabricated via PBF-AM. Previous experiments revealed a higher crack propagation rate in the coarse columnar-grained microstructural regions when compared against fine-grained areas. Here, a strain gradient crystal plasticity model was adapted to study the fracture-related mechanical fields at the crack tip in the two microstructures. The simulation results showed a consistent influence of grain structure and texture on crack propagation, as was seen in the experiment. The model analysis revealed higher crack propagation driving force along crack direction in the coarse-grained sharply textured microstructure and higher driving force for crack kinking in fine-grained more diffusely textured microstructure, which is ascribed to the combined effect of yield stress, hardening rate, texture and grain morphology. The presented modeling approach will facilitate the development of the AM-based accurate microstructure design by deepening the fundamental study in AM-specific microstructure-properties relations.

36 MATERIALS SCIENCE↗

Microstructure control to improve creep strength of alumina-forming austenitic heat-resistant steel by pre-strain

Highlights: • The effect of pre-strain on creep strength of AFA steel was studied. • The creep test was performed at 700°C and 200Mpa, and the aging test was carried out using box furnace at 700°C to simulate the microstructural evolution during creep. • Microstuctural evolution was observed by using SEM, EBSD, and TEM to investigate the relationship between creep strength and microstructure. - Abstract: At 700 °C and 200 MPa, the creep rupture time of W-containing alumina-forming austenitic heat-resistant (WAFA) steel increases from 1044 to 3119 h by pre-strain. Pre-strain introduces a lot of dislocation into the matrix and most of the dislocations remain stable to the end of creep without recovery and recrystallization. In addition, the dislocations have enabled secondary NbC and Laves phase to be uniformly distributed and refined. However, the dislocations lower grain boundary strength due to the coarsening of precipitates along grain boundaries Therefore, the increase in the creep rupture time in spite of deterioration of grain boundary strength is attributed to the dislocation strengthening and enhanced precipitation hardening within grains.

36 MATERIALS SCIENCE↗

Physics-Based Modeling and Simulation of Self-Reacting Friction Stir Welding Using Computational Fluid Dynamics

A physics-based model was developed to simulate the behavior of material in a self-reacting friction stir welding (SR-FSW) process for the joining of metals. This steady-state model builds upon fundamental computational fluid dynamic (CFD) principles within Ansys Fluent to solve the discretized equations. The effective viscosity is calculated using a viscoplastic model using a Sheppard-Wright formulation of flow stress. Numerous advancements have been made in the incorporated physics including (1) temperature-dependent material properties; (2) locally adaptable flow and thermal boundary conditions; and (3) adapting material properties in nugget in response to microstructural changes. Simulation strategies to accelerate computation and improve numerical stability include adapting the mesh refinement and solver relaxation factors during simulation. The result is a highly robust and computationally efficient model capable of providing the material flow and temperature history across the domain. As material history determines the local microstructure and ultimately weld strength, an accurate and detailed physics-based model has the potential to accelerate SR-FSW process development. The model is highly adaptable to changes in process parameters, tool design, or alloy.

Process Modeling↗

Prediction of Probabilistic Detonation Threshold via Millimeter-Scale Microstructure-Explicit and Void-Explicit Simulations

We present an approach and relevant models for predicting the probabilistic shoc-to-detonation transition (SDT) behavior and Pop plot (PP) of heterogeneous energetic materials (HEM) via mesoscopic microstructure-explicit (ME) and void explicit (VE) simulations at the millimeter (mm) sample size scale. Although the framework here is general, the particular material considered in this paper is pressed Octahydro-1,3,5,7-tetranitro-1,2,3,5-tetrazocine (HMX). To systematically delineate the effects of material heterogeneities, four material cases are considered. These cases are homogeneous material, material with granular microstructure but no voids, homogeneous material with voids, and material with both granular microstructure and voids. Statistically equivalent microstructure sample sets (SEMSS) are generated and used. Eulerian hydrocode simulations explicitly resolve the material heterogeneities, voids, and the coupled mechanical-thermal-chemical processes. In particular, it is found that both microstructure and voids strongly influence the SDT behavior and PP. The effects of different combinations of microstructure heterogeneity and voids on the SDT process and PP are quantified and rank-ordered. The overall framework uses the Mie–Grüneisen equation of state and a history variable reactive burn model (HVRB). A novel probabilistic representation for quantifying the PP is developed, allowing the calculation of (1) the probability of observing SDT at a given combination of shock pressure and run distance, (2) the run-distance to detonation under a given combination of shock pressure and prescribed probability, and (3) the shock pressure required for achieving SDT at a given run distance with a prescribed probability. The results are in agreement with general trends in experimental data in the literature.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Age hardening response of Cu-30Ni alloys: The role of Si microalloying additions

Cu-30Ni alloys offer high strength and excellent corrosion resistance for maritime applications. While primarily a solid solution system, industrial alloys typically include microalloying additions of Fe, Mn, Nb and/or Si to enable age hardening. However, an understanding of the microstructural evolution during age hardening remains incomplete. Here, we conduct systematic ageing treatments and report the resulting hardness and microstructures. The Cu-30Ni alloy with Si aged at 650 °C for 6 h demonstrates significantly enhanced Vickers hardness, reaching ∼201 HV 1 compared to 103 HV 1 for the as-homogenised sample. Si-rich clusters and γ′ precipitates are identified, with their composition, size, and volume fraction quantified to determine their strengthening contributions. First-principles atomistic simulations elucidate the underlying formation mechanisms of these clusters and precipitates, highlighting the critical role of Si in driving their nucleation and growth. This study advances the design of high-strength, Cu alloys with the potential for corrosion resistance in demanding maritime environments.

Age hardening↗