Search NASA⌕ Search

SEARCH · Search NASA

Results for “silver activation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Red Plague Control Plan (RPCP)

SCOPE: Prescribes the minimum requirements for the control of cuprous / cupric oxide corrosion (a.k.a. Red Plague) of silver-coated copper wire, cable, and harness assemblies. PURPOSE: Targeted for applications where exposure to assembly processes, environmental conditions, and contamination may promote the development of cuprous / cupric oxide corrosion (a.k.a. Red Plague) in silver-coated copper wire, cable, and harness assemblies. Does not exclude any alternate or contractor-proprietary documents or processes that meet or exceed the baseline of requirements established by this document. Use of alternate or contractor-proprietary documents or processes shall require review and prior approval of the procuring NASA activity.

Cooke, Robert W.↗
DOE OSTI2022

Reconfigurable Electrical Networks within a Conductive Hydrogel Composite

Soft materials that exhibit compliance, programmability, and reconfigurability can have a transformative impact as electronic skin for applications in wearable electronics/soft robotics. There has been significant progress in soft conductive materials; however, achieving electrically controlled and reversible changes in conductivity and circuit connectivity remains challenging. To overcome this limitation, a soft material architecture with reconfigurable conductive networks of silver flakes embedded within a hydrogel matrix is presented. The conductive networks can be reversibly created/disconnected through various stimuli, including current, humidity, or temperature. Such stimuli affect electrical connectivity of the hydrogel by controlling its water content, which can be modulated by evaporation under ambient conditions (passive dehydration), evaporation through electrical Joule heating (active dehydration), or absorption of additional water (rehydration). The resulting change in electrical conductivity is reversible and repeatable, endowing the composite with on-demand reconfigurable conductivity. To highlight this material's unique properties, it is shown that conductive traces can be reconfigured after severe damage and revert to lower conductivity after rehydration. Additionally, a quadruped robot is demonstrated that can respond to stimuli by changing direction following exposure to excess water, thereby achieving reprogrammable locomotion behaviors.

36 MATERIALS SCIENCE↗
NASA NTRS1990

The Stellar X-ray Polarimeter - A focal plane polarimeter for the Spectrum X-Gamma mission

This paper describes an X-ray polarimeter that will be flown on the Spectrum X-Gamma mission. The instrument exploits three distinct physical processes to measure polarization: Bragg reflection from a graphite crystal, Thomson scattering from a metallic lithium target, and photoemission from a cesium iodide photocathode. These three methods allow polarization measurements over an energy band from 0.3 to 12 keV. The polarimeter will make possible sensitive measurements of several hundred known X-ray sources. X-ray polarization measurements will make it possible to constrain the geometry of gas flow in X-ray binaries, identify nonthermal emission in supernova remnants, test current models for X-ray emission in radio pulsars, determine the radiation mechanisms in active galactic nuclei, and search for inertial frame dragging (Lense-Thirring effect) around the putative black hole in Cygnus X-1.

Kaaret, P.↗
NASA NTRS1990

Characterization of metal oxide absorbents for regenerative carbon dioxide and water vapor removal for advanced portable life support systems

Characterization of the performance of a silver-oxide-based absorbent in terms of its ability to remove both gaseous CO2 and water vapor in an astronaut portable life support systems (PLSS) is discussed. Attention is focused on regeneration of the absorbent from the carbonite state of the oxide state, preconditioning of the absorbent using a humidified gas stream, and absorption breakthrough testing. Based on the results of bench-scale experiments, a test plan is carried out to further characterize the silver-oxide-based absorbent on a larger scale; it calls for examination of the absorbent in both an adiabatic packed bed and a near-isothermal cooled bed configuration. It is demonstrated that the tested absorbent can be utilized in a way that removes substantial amounts of CO2 and water vapor during an 8-hour extravehicular activity mission, and that applying the absorbent to PLSS applications can simplify the ventilation loop.

Kast, Timothy P.↗
DOE OSTI2026

Coordination of Anle138b to Silver Results in Selective Reduction of a C-terminal truncated Alpha-synuclein Protein and Increased Aggregate Size

Parkinson’s disease (PD) is a prevalent age-related neurodegenerative syndrome, partially thought to be caused by a decrease in alpha-synuclein proteostasis. Anle138b = 5-(1,3-benzodioxol-5-yl)-3-(3-bromophenyl)-1H-pyrazole (HL), is undergoing clinical trials as a promising mitigator of alpha-synuclein aggregation. Because complexation to metals is known to modulate the activity of several drugs, we have prepared and characterized: H2L(ClO4), [CuI(µ-L)]3, and [AgI(µ-L)]3. To better understand the bioviability of these compounds, we monitored their effects in a cell culture model of alpha-synuclein protein aggregation using human alpha-synuclein pre-formed fibrils (PFFs). Using two different anti-alpha-synuclein antibodies, our data suggests that [AgI(µ-L)]3 decreases a C-terminal truncated protein that is approximately 12.4 kDa, as well as increases the size and alters the shape of PFF-induced aggregates. This indicates that [AgI(µ-L)]3 impacts aggregation in a manner different from HL and may serve as a novel tool for studying C-terminal truncation related aggregation chemistry.

Rue, Kelly L.↗
DOE OSTI2026

Restoring Escaped Zincate in Rechargeable Alkaline Zinc Batteries with a Seed-in-Nanoshell Design

Rechargeable alkaline zinc batteries are promising candidates for safe and low-cost energy storage, but suffer from ZnO dissolution that causes irreversible active material loss and rapid capacity decay. Here, we report a seed-in-nanoshell ZnO anode architecture that mitigates dissolution by combining physical confinement with electrochemical restoration of dissolved zincate species. ZnO particles are encapsulated within an ion-sieving carbon nanoshell that restricts zincate diffusion, maintains electrical conductivity, and stabilizes repeated solid–solution–solid transformations. Silver (Ag) nanoparticles incorporated into the nanoshell act as zincophilic nucleation seeds, lowering the Zn deposition barrier and directing the redeposition of dissolved zincate back to metallic Zn during charging. This confinement-enabled restoration mechanism converts zincate dissolution from an irreversible loss pathway into a recoverable process, enabling improved performance under harsh test conditions. The anode also delivers 227.9 mAh g −1 at −40 °C. Finally, a scalable tens-of-gram synthesis of ZnO@Ag is demonstrated, underscoring the practical potential of this strategy for advanced aqueous zinc batteries.

25 ENERGY STORAGE↗
NASA NTRS1988

Experimental results on atomic oxygen corrosion of silver

The results of an experimental study of the reaction kinetics of silver with atomic oxygen in 10 degree increments over the temperature range of 0 to 70 C is reported. The silver specimens, of the order of 10,000 A in thickness, were prepared by thermal evaporation onto 3 inch diameter polished silicon wafers. There were later sliced into pieces having surface areas of the order of 1/4 to 1/2 square inch. Atomic oxygen was generated by a gas discharge in a commercial plasmod asher operating in the megahertz frequency range. The sample temperature within the chamber was controlled by means of a thermoelectric unit. Exposure of the silver specimens to atomic oxygen was incremental, with oxide film thickness measurements being carried out between exposures by means of an automated ellipsometer. For the early growth phase, the data can be described satisfactorily by a logarithmic growth law: the oxide film thickness increases as the logarithm of the exposure time. Furthermore, the oxidation process is thermally activated, the rate increasing with increasing temperature. However, the empirical activation energy parameter deduced from Arrhenius plots is quite low, being of the order of 0.1 eV.

Fromhold, Albert T.↗
DOE OSTI2023

Thermohydraulic Design Analysis of the Target Assembly in the Material Plasma Exposure Experiment Facility

The Material Plasma Exposure eXperiment (MPEX) project seeks to design a steady-state linear plasma facility at Oak Ridge National Laboratory that will be used to study plasma-material interactions (PMIs) at fusion prototypic levels, supporting the evaluation and development of materials for the next generation of fusion devices. This study is focused on PMI exposure of small-size neutron-irradiated specimens, which are clamped onto an actively cooled component. A thermohydraulic evaluation of a new MPEX target assembly design to assess the appropriate operation during MPEX operation is presented. To further guide the design and assess the structural integrity of the components under expected loads, preliminary thermomechanical stress analyses were also conducted. To ensure good thermal contact between the components, thermal interface materials, such as silver flexible graphite, were used in the assembly. It was found that the maximum target temperatures of 1572, 1463, and 1315 K were obtained for Grafoil thicknesses of 0.61, 0.38, and 0.25 mm, respectively. The distribution of the axial deformation at high heat fluxes showed that there are no gaps between components, indicating good contact at material interfaces. Moreover, the contact pressure between the target and other components indicated that very good contact was established at these interfaces. Furthermore, the stress-strain conditions for the target will be further used to assess the appropriate operation during MPEX experiments and gain insight into materials science phenomena during PMI experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Nickel promotes selective ethylene epoxidation on silver

Over the last 80 years, chlorine (Cl) has been the primary promoter of the ethylene epoxidation reaction valued at ~40 billion USD per year, providing a ~25% selectivity increase over unpromoted silver (Ag) (~55%). Promoters such as cesium, rhenium, and molybdenum each add a few percent of selectivity enhancements to achieve 90% overall, but their codependence on Cl makes optimizing and understanding their function complex. Here, we took a theory-guided, single-atom alloy approach to identify nickel (Ni) as a dopant in Ag that can facilitate selective oxidation by activating molecular oxygen (O 2 ) without binding oxygen (O) too strongly. Surface science experiments confirmed the facile adsorption/desorption of O 2 on NiAg, as well as demonstrating that Ni serves to stabilize unselective nucleophilic oxygen. Supported Ag catalyst studies revealed that the addition of Ni in a 1:200 Ni to Ag atomic ratio provides a ~25% selectivity increase without the need for Cl co-flow and acts cooperatively with Cl, resulting in a further 10% initial increase in selectivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Local Parameters of PERC Solar Cells Metallized with Screen Printed Cu-Paste

For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include: 1) bulk Cu has a similar conductivity to Ag (1.7 one millionth O-cm for Cu, 1.6 one millionth O-cm for Ag, and 2) Cu is -100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper contacts include: 1) easy oxidation, and 2) diffusion into the Si cell and recombination activity. To summarize: 1) Rs map shows some regions with very high Rs, indicating no contact in those areas; 2) the histogram shows the peak Rs -5 ohm.cm2, which explains the high FF loss due to Rs; and 3) DLIT indicates non-uniformity in J01 and J02.

copper↗
DOE OSTI2024

Exploring the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells

For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include 1) bulk Cu has a similar conductivity to Ag (1.7 mu O-cm for Cu, 1.6 mu O-cm for Ag) and 2) Cu is approximately 100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper (Cu) contacts include 1) easy oxidation and 2) diffusion into the Si cell and recombination activity.

copper paste↗
DOE OSTI2022

Brazing characteristics, microstructure, and wettability of laser powder bed fusion additive manufactured GRCop-84 compared to CuCrZr and OFC, and brazing to titanium-zirconium-molybdenum alloy limiters

Laser Powder Bed Fusion (L-PBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense, high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa with 20% elongation; superior to other competing copper alloys. Braze wetting characteristics of GRCop-84 with Ag-Cu-X, and Au-Cu brazes were similar to CuCrZr, but less than oxygen free copper. No difference in wetting was observed between infill and surface contour areas in L-PBF GRCop-84. Wet sanding to 240 grit (R a =0.24 µm) was considered the optimal surface condition. Silver diffusing through GRCop-84 depleted Cr 2 Nb precipitates from the copper grain and deposited agglomerations of coarsened precipitates within silver-rich regions of intergranular diffusion once a density threshold was reached. Microstructure modification was minimized with 50Au-50Cu braze implying that silver caused precipitate coarsening and agglomeration, and not high temperature exposure. Coarsened precipitates were observed on the surface within braze pools implying a contribution to braze wetting. Palcusil-25, Ticusil, CuSil-ABA, and 50Au-50Cu brazes were suitable for brazing to unplated Titanium-Zirconium-Molybdenum (TZM), while sulfamate nickel plating to allows wetting with CuSil or other non-active brazes. Additionally, vacuum brazing techniques were developed to join a 1 mm thick layer of TZM to the front of additive manufactured GRCop-84 waveguides considering the brazing characteristics of both GRCop-84, TZM, and internal stress from the difference in coefficient in thermal expansion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2005

Microbiological Characterization and Concerns of the International Space Station Internal Active Thermal Control System

Since January 1999, the chemical the International Space Station Thermal Control System (IATCS) and microbial state of (ISS) Internal Active fluid has been monitored by analysis of samples returned to Earth. Key chemical parameters have changed over time, including a drop in pH from the specified 9.5 +/- 0.5 ta = 58.4, an increase in the level of total inorganic carbon (TIC), total organic carbon (TOC) and dissolved nickel (Ni) in the fluid, and a decrease in the phosphate (PO,) level. In addition, silver (AS) ion levels in the fluid decreased rapidly as Ag deposited on internal metallic surfaces of the system. The lack of available Ag ions coupled with changes in the fluid chemistry has resulted in a favorable environment for microbial growth. Counts of heterotrophic bacteria have increased from less than 10 colony-forming units (CFUs)/l00 mL to l0(exp 6) to l0(exp 7) CFUs/100 mL. The increase of the microbial population is of concern because uncontrolled microbiological growth in the IATCS can contribute to deterioration in the performance of critical components within the system and potentially impact human health if opportunistic pathogens become established and escape into the cabin atmosphere. Micro-organisms can potentially degrade the coolant chemistry; attach to surfaces and form biofilms; lead to biofouling of filters, tubing, and pumps; decrease flow rates; reduce heat transfer; initiate and accelerate corrosion; and enhance mineral scale formation. The micro- biological data from the ISS IATCS fluid, and approaches to addressing the concerns, are summarized in this paper.

Roman, Monsi C.↗
DOE OSTI2020

Dual-atom Ag 2 /graphene catalyst for efficient electroreduction of CO 2 to CO

Electrochemical reduction of CO 2 into value-added carbon compounds offers a promising strategy to mitigate global warming, but present challenges for chemistry due to the poor selectivity and stability of electrocatalysts. In this work, we report a dual-atom Ag 2 /graphene catalyst featuring well-defined AgN 3 -AgN 3 active site for CO 2 electrochemical reduction. This dual-atom catalyst can drive CO 2 reduction reaction at a potential as high as -0.25 V, and exhibit excellent CO Faradic efficiency up to 93.4 % with a current density of 11.87 mA cm -2 at -0.7 V and long-term stability, far surpassing the single-atom Ag 1 /graphene and the traditional silver nanoparticle catalysts. Finally, DFT calculations reveal that the dual-atom Ag site lowers the barrier for the formation of *COOH by stabilizing the *CO 2 through the concomitant interactions with the C and an O atom of CO 2 , resulting in excellent catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1986

The high energy transmission grating spectrometer for AXAF

Attention is given to a high energy transmission grating spectrometer that operates over the range 0.4-8 keV, giving resolving powers of 100-1000 and effective areas of 10-200 sq cm. The instrument, which is part of the MIT high resolution X-ray spectroscopy investigation, consists of a single array of grating facets of two types: medium energy gratings of 0.6-micron period, 0.5-micron thick silver mounted behind the outer three AXAF mirrors, and high energy gratings of 0.2-micron period, 1.0-micron thick gold mounted behind the inner three mirrors. The gratings are oriented so as to correct for coma and so that the medium and high energy spectra form a shallow 'X' at the AXAF focal plane. Likely targets include normal stars, binary X-ray sources, active galactic nuclei and quasars. The HETGS can also be used to give moderate resolution spectra of slightly extended sources and monochromatic images of sources with strong lines, such as supernova remnants in nearby galaxies.

Canizares, C. R.↗
NASA NTRS2000

A deficiency in DNA repair and DNA-PKcs expression in the radiosensitive BALB/c mouse

We have studied the efficiency of DNA double strand break (DSB) rejoining in primary cells from mouse strains that show large differences in in vivo radiosensitivity and tumor susceptibility. Cells from radiosensitive, cancer-prone BALB/c mice showed inefficient end joining of gamma ray-induced DSBs as compared with cells from all of the other commonly used strains and F1 hybrids of C57BL/6 and BALB/c mice. The BALB/c repair phenotype was accompanied by a significantly reduced expression level of DNA-PKcs protein as well as a lowered DNA-PK activity level as compared with the other strains. In conjunction with published reports, these data suggest that natural genetic variation in nonhomologous end joining processes may have a significant impact on the in vivo radiation response of mice.

Non-NASA Center↗
DOE OSTI2024

Solid-State Hydroxide Ion Conductivity in Silver(I) Oxide, Ag 2 O

Silver (I) oxide, Ag 2 O, precipitated as microcrystals by combining aqueous silver(I) nitrate and KOH solutions, was found to be a solid-state hydroxide ion conductor with ionic conductivity on the order of 10 -3 S/cm. The proton chemical shifts at 4.87 and -7.35 ppm measured by solid-state 1H-NMR experiments are attributed to water molecules and in-lattice OH - coordinated to silver, respectively. The lack of spinning sidebands around the 4.87 ppm peak indicates rapid reorientation on the NMR timescale, suggesting that the water molecules are adsorbed to the surface of the Ag 2 O crystals. Pulsed field gradient measurements gave similar diffusion coefficients (2 x 10 -7 cm 2 /s at 298K) for all three proton environments indicating chemical exchange between sites on the millisecond timescale. The activation energy for OH - diffusion measured by NMR (0.18 eV) was comparable to that obtained by conductivity measurements and density functional theory (DFT) electronic structure calculations. Furthermore, the calculated Pourbaix diagram of Ag 2 O is consistent with the slightly lower sample density observed in He pycnometry and thermogravimetric measurements.

25 ENERGY STORAGE↗
DOE OSTI2025

Crossing the Oxo‐Peroxo Wall for Selective Electrochemical Epoxidation

Electrochemical oxidation in water requires the formation of reactive oxygen species to be able to oxidize unsaturated hydrocarbons to epoxides, aldehydes, and ketones. These reactions, broadly classified as alternative oxidation reactions (AOR), directly compete with the prevalent oxygen evolution reaction (OER). In molecular catalysis, the Oxo-Wall dictates a transition from a stable oxo intermediate (OER active) to a meta-stable metal-oxo (OER inactive) generally occurs. In this work on heterogeneous catalysis, the same Oxo-Wall applies, however, a meta-stable oxo preferentially coordinates with lattice oxygen to form a more stable surface peroxo intermediate. A universal free energy onset of this process is identified at 3.39 eV under electrochemical activation in water and show that it is completely decoupled from the OER oxo species. Such decoupling gives rise to a new region of oxygen reactivity relevant for AOR where a selective oxidation of the unsaturated C-C bonds is predicted to occur instead of OER. A distinct AOR overpotential volcano is constructed and identify recently reported electrocatalysts, including palladium-platinum for propylene epoxidation and silver-nickel for ethylene epoxidation, along with others such as TiO 2 and CuO. Broader implications and limitations of electrochemical AOR are discussed, highlighting their potential to enable electrochemically enhanced thermal catalysis.

Electrocatalysis↗