Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Radiation of an acoustic source near the trailing edge of a wing in forward motion

The acoustic sources simulating engine or jet noise are located near the trailing edge. During landing or take-off operations the flap angle is not small. Solutions for the scattering of the acoustic sources, monopoles, dipoles or quadrupoles, by the wing with the flap at finite angle are constructed for the case that the acoustic wave length is much larger than the length of the flap but may be of the same order as the chord. For each given geometry of the flap and the position of the singularities, critical orientations of the dipoles and the quadrupoles are defined along which the noise becomes 'suppressed', i.e., the far field pressure becomes one order smaller.

Ting, L.↗
DOE OSTI2021

Simulations of ion heating due to ion-acoustic instabilities in presheaths

Particle-in-cell, direct simulation Monte Carlo simulations reveal that ion-acoustic instabilities excited in presheaths can cause significant ion heating. Ion-acoustic instabilities are excited by the ion flow toward a sheath when the neutral gas pressure is small enough and the electron temperature is large enough. A series of 1D simulations were conducted in which neutral plasma (electrons and ions) was uniformly sourced with an ion temperature of 0.026 eV and different electron temperatures (0.1 eV–50 eV). Ion heating was observed when the electron-to-ion temperature ratio exceeded the minimum value predicted by linear response theory to excite ion-acoustic instabilities at the sheath edge (T e /T i ≈ 28). When this threshold was exceeded, the temperature equilibration rate between ions and electrons rapidly increased near the sheath so that the local temperature ratio did not significantly exceed the threshold for instability. This resulted in significant ion heating near the sheath edge, which also extended back into the bulk plasma; presumably due to wave reflection from the sheath. Furthermore, this ion-acoustic wave heating mechanism was found to decrease for higher neutral pressures, where ion-neutral collisions damp the ion-acoustic waves and ion heating is instead dominated by inelastic collisions in the presheath.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

TPSAS-NF1676L-33433-DND

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for aircraft noise reduction, and are characterized by a complex valued frequency-dependent impedance. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic scattering of geometric bodies treated with acoustic liners. This work considers using either an impedance boundary condition or admittance boundary condition to allow acoustic scattering problems to be modeled with geometries consisting of both un-lined and lined surfaces; admittance is defined to be the inverse of impedance. Three different acoustic liner models will be discussed: the Extended Helmholtz Resonator Model, the Three-Parameter Impedance Model, and a Broadband Model. In the Extended Helmholtz Resonator Model and Three-Parameter Impedance Model, the liner impedance is specified at a single frequency; the Broadband Model allows for the investigation of multiple frequencies simultaneously. The impedance and admittance boundary conditions for each model will be derived and coupled with a time-domain boundary integral equation. The scattering solution will be obtained iteratively using spatial and temporal basis functions. Stability will be demonstrated through eigenvalue analysis. Moreover, fast algorithms and high performance computing are considered to both assess and reduce the computational cost of the simulation.

Michelle E Rodio↗
NASA NTRS2020

INVESTIGATING THE FEASIBILITY AND STABILITY FOR MODELING ACOUSTIC WAVE SCATTERING USING A TIME-DOMAIN BOUNDARY INTEGRAL EQUATION WITH IMPEDANCE BOUNDARY CONDITION

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet and environmentally friendly aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for aircraft noise reduction and are characterized by a frequency-dependent impedance. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. This work considers using either an impedance or an admittance (inverse of impedance) boundary condition to allow for acoustic scattering problems to be modeled with geometries consisting of both un-lined and lined surfaces. Three acoustic liner models are discussed: the Extended Helmholtz Resonator Model, the Three-Parameter Impedance Model, and the Broadband Impedance Model. In both the Helmholtz and Three-Parameter models, liner impedance is specified at a given frequency, whereas the Broadband model allows for the investigation of multiple frequencies simultaneously. The impedance and admittance boundary conditions for acoustic liners are derived for each model and coupled with a time-domain boundary integral equation. The scattering solution is obtained iteratively using a boundary element method with constant spatial and third-order temporal basis functions. Time-domain boundary integral equations are unfortunately prone to numerical instabilities due to resonant frequencies resulting from non-trivial solutions in the interior domain. When reformulated with the Burton-Miller method, the instabilities are eliminated. Using a Burton-Miller reformulation, the stability of the boundary element method assuming a liner boundary condition is assessed using eigenvalue analysis. The stability of each liner model is discussed, and it is shown that the Three-Parameter and Broadband models are sufficient for modeling an acoustic liner on the surface of scattering bodies. The Helmholtz model demonstrates strict limitations for stability, whereas the Three-Parameter and Broadband models are stable for most cases. Also included in this work is an assessment of the spatial accuracy of the time-domain boundary element method with respect to the surface element basis functions, as well as a performance study of the numerical algorithm.

computational mathematics↗
NASA NTRS2000

Improvements To Progressive Wave Tube Performance Through Closed-Loop Control

This report documents recent improvements to the acoustic and thermal control systems of the Thermal Acoustic Fatigue Apparatus (TAFA), a progressive wave tube test facility at the NASA Langley Research Center, Hampton, Virginia. A brief summary of past acoustic performance is given first to serve as a basis for comparison with the new performance data using a multiple-input, closed-loop, narrow-band controller. Performance data in the form of test section acoustic power spectral densities and coherence are presented in three of six facility configurations for a variety of input spectra. Tested spectra include uniform, two cases of pink noise, three cases of narrow-band random, a simulated launch payload bay environment for an expendable launch vehicle, and a simulated external acoustic load for the aft section of a reusable launch vehicle. In addition, a new closed-loop temperature controller and thermocouple data acquisition system are described.

Rizzi, Stephen A.↗
NASA NTRSDate not supplied

Investigating the Feasibility and Stability for Modeling Broadband Acoustic Wave Scattering using a Time-Domain Boundary Integral Equation

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. Acoustic liners are an effective tool for reducing aircraft noise and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model is discussed in which the liner impedance is specified along a wide range of frequencies. An impedance boundary condition is derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate. It is assumed the flat plate has surfaces treated with acoustic liners. The stability of the numerical algorithm is assessed using eigenvalue analysis.

mathmatics↗
NASA NTRS2020

TPSAS-NF1676L-36025-DND

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A broadband impedance model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis.

Michelle E Rodio↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗
DOE OSTI2019

Global gyrokinetic simulation of microturbulence with kinetic electrons in the presence of magnetic island in tokamak

An electrostatic model has been formulated and implemented in the gyrokinetic toroidal code to study the nonlinear ion temperature gradient (ITG) turbulence in the presence of an n = 1, m = 2 magnetic island. The ions are described by the gyrokinetic equation while the electrons are treated with the drift-kinetic equation. In our simulation, an n = 1, m = 2 electrostatic mode is formed with the same vortex structure of the magnetic island. When the magnetic island flattening effect is turned on, the island vortex mode is well preserved and couples to the n = 0, m = 0 geodesic acoustic mode. Simulation shows that the magnetic island can suppress the ITG turbulence at the island O-point and strengthen it near the X-point. We show that the vortex mode can generate a substantial helical shear flow around the island. Finally, we also find that the turbulence and transport are suppressed inside the island and enhanced at the island X-point

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2011

2011 Ground Testing Highlights Article

Two tests supporting development of the launch abort system for the Orion MultiPurpose Crew Vehicle were run in the NASA Ames Unitary Plan wind tunnel last year. The first test used a fully metric model to examine the stability and controllability of the Launch Abort Vehicle during potential abort scenarios for Mach numbers ranging from 0.3 to 2.5. The aerodynamic effects of the Abort Motor and Attitude Control Motor plumes were simulated using high-pressure air flowing through independent paths. The aerodynamic effects of the proximity to the launch vehicle during the early moments of an abort were simulated with a remotely actuated Service Module that allowed the position relative to the Crew Module to be varied appropriately. The second test simulated the acoustic environment around the Launch Abort Vehicle caused by the plumes from the 400,000-pound thrust, solid-fueled Abort Motor. To obtain the proper acoustic characteristics of the hot rocket plumes for the flight vehicle, heated Helium was used. A custom Helium supply system was developed for the test consisting of 2 jumbo high-pressure Helium trailers, a twelve-tube accumulator, and a 13MW gas-fired heater borrowed from the Propulsion Simulation Laboratory at NASA Glenn Research Center. The test provided fluctuating surface pressure measurements at over 200 points on the vehicle surface that have now been used to define the ground-testing requirements for the Orion Launch Abort Vehicle.

Ross, James C.↗
NASA NTRS1978

Acoustic tests of duct-burning turbofan jet noise simulation

The results of a static acoustic and aerodynamic performance, model-scale test program on coannular unsuppressed and multielement fan suppressed nozzle configurations are summarized. The results of the static acoustic tests show a very beneficial interaction effect. When the measured noise levels were compared with the predicted noise levels of two independent but equivalent conical nozzle flow streams, noise reductions for the unsuppressed coannular nozzles were of the order of 10 PNdB; high levels of suppression (8 PNdB) were still maintained even when only a small amount of core stream flow was used. The multielement fan suppressed coannular nozzle tests showed 15 PNdB noise reductions and up to 18 PNdB noise reductions when a treated ejector was added. The static aerodynamic performance tests showed that the unsuppressed coannular plug nozzles obtained gross thrust coefficients of 0.972, with 1.2 to 1.7 percent lower levels for the multielement fan-suppressed coannular flow nozzles. For the first time anywhere, laser velocimeter velocity profile measurements were made on these types of nozzle configurations and with supersonic heated flow conditions. Measurements showed that a very rapid decay in the mean velocity occurs for the nozzle tested.

Knott, P. R.↗
NASA NTRS2018

Investigation of Multi-Input, Multi-Output (MIMO) Random Control Applied to Direct Field Acoustic Testing

Direct Field Acoustic Testing (DFAT) offers potential cost and time savings over reverberant chamber acoustic testing of spacecraft. The NASA Multi-Purpose Crew Vehicle (MPCV) Program recently directed a series of acoustic tests on Orion structural test articles comparing DFAT and reverberant testing of the same test article with a view to qualifying DFAT for manned space flight vehicles. The verification process compared four parameters noise level compliance with the one third octave test specification, spatial uniformity of the acoustic field, spatial correlation of the acoustic field and vibration response of vehicle structure, including representative solar array panels. While the results of the verification were encouraging, MPCV Loads and Dynamics engaged Quartus Engineering to investigate whether alternative MIMO random control strategies might improve the spatial uniformity and/or the spatial correlation of the DFAT acoustic field. This paper presents the results of acoustic field simulations of the DFAT test and provides a better understanding of how MIMO random control systems originally developed for vibration and structural durability testing can be expected to perform in DFAT testing.

Direct Field↗
DOE OSTI2022

Anisotropic Thermally Conductive Composites Enabled by Acoustophoresis and Stereolithography

Opportunities to improve thermal management in electronic devices are currently hindered by processing constraints that limit thermal conductivity in polymer-matrix composites. Active patterning of filler particles is a promising route to improve conductivity while retaining processability by improving particle contact density and directing heat along optimized pathways. Here, we employ acoustic patterning to align and compact filler particles into stripes during stereolithographic 3D printing. This approach produces polymer-based composite materials with highly efficient embedded heat transport pathways which reach 95 vol% particle utilization (relative to the parallel conduction upper limit). These composites exhibit anisotropic thermal conductivity up to 300% higher than unpatterned composites, with in-plane anisotropy ratios of up to 350%. Combining this high conductivity with 3D printing enables materials with engineered heat networks that optimize transport from hot spots to heatsinks while maintaining low viscosity for fast particle patterning and for infiltration around electronic components. Finally, numerical simulations of acoustic assembly of particles with varied geometry, when compared to experimentally characterized particle packing, illuminate pathways for further improving conductivity by optimizing particle geometry for alignment and stacking of particles with maximum contact surface area.

36 MATERIALS SCIENCE↗
NASA NTRS2011

Validation and Simulation of ARES I Scale Model Acoustic Test -1- Pathfinder Development

The Ares I Scale Model Acoustics Test (ASMAT) is a series of live-fire tests of scaled rocket motors meant to simulate the conditions of the Ares I launch configuration. These tests have provided a well documented set of high fidelity measurements useful for validation including data taken over a range of test conditions and containing phenomena like Ignition Over-Pressure and water suppression of acoustics. To take advantage of this data, a digital representation of the ASMAT test setup has been constructed and test firings of the motor have been simulated using the Loci/CHEM computational fluid dynamics software. Within this first of a series of papers, results from ASMAT simulations with the rocket in a held down configuration and without water suppression have then been compared to acoustic data collected from similar live-fire tests to assess the accuracy of the simulations. Detailed evaluations of the mesh features, mesh length scales relative to acoustic signals, Courant-Friedrichs-Lewy numbers, and spatial residual sources have been performed to support this assessment. Results of acoustic comparisons have shown good correlation with the amplitude and temporal shape of pressure features and reasonable spectral accuracy up to approximately 1000 Hz. Major plume and acoustic features have been well captured including the plume shock structure, the igniter pulse transient, and the ignition overpressure. Finally, acoustic propagation patterns illustrated a previously unconsidered issue of tower placement inline with the high intensity overpressure propagation path.

Putnam, G. C.↗
DOE OSTI2025

Earthquake detection in a simulated lunar regolith using distributed acoustic sensing

Current models of inner lunar geology have largely been inferred from the seismic experiments and observations performed during the Apollo missions that comprised a relatively small number of seismic instruments. Refining constraints on fundamental lunar relationships such as crust-mantle and mantle-core boundaries in the future will require seismic arrays spanning larger epicentral distances. A promising technology for installing dense seismic arrays with minimal human effort is distributed acoustic sensing (DAS), an approach that allows a single length of fiber optic cable to act as hundreds or thousands of sensors when coupled with a DAS interrogator. While terrestrial uses of DAS technology for seismic monitoring rely on burying the cable to maximize fidelity of seismic signal transmission to the fiber, digging meters of trench to bury optical fiber on lunar or planetary surfaces is logistically infeasible. To evaluate DAS signal attenuation due to surface deployment of cable in lunar regolith, we completed earthquake detection analyses that evaluated the sensitivity of an optic-fiber DAS system to seismic signals at different burial depths. We deployed a single-mode fiber in a 10-m open-bottom wooden box filled with a lunar regolith simulant (LRS) with fiber buried at different depths within the LRS and recorded signals for four regional and local earthquakes. The results were used to identify and evaluate signal attenuation in surface-deployed fiber compared to buried fiber in the LRS. Burial depth responses to active-source signals were also evaluated similar to previous studies characterizing DAS sensitivity of surface-deployed fiber. Atmospheric noise was minimal as the cable was deployed in an indoor environment; however, where observed, atmospheric and anthropogenic noise was filtered out using the same bandpass filtering used to identify earthquake events. We found that signal attenuation of the surface-deployed fiber compared to buried fiber was relatively high in active-source experiments but was not consistently observed in earthquake signals. That burial depth is not highly correlated to attenuation of the observed earthquake signals indicates that in a noise-limited environment, placing DAS-interrogated fiber directly at the regolith surface may be a promising deployment strategy to consider for sensing remote seismic signals during lunar exploration.

58 GEOSCIENCES↗