Search NASA⌕ Search

SEARCH · Search NASA

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Turbulent heat transfer in a channel with two right-angled bends

A numerical study is reported on the flow and heat transfer in a channel with two right-angled bends. The k-epsilon turbulence model with a refined near-wall model is adopted for the computation of the flow field for step ratios ranging H/W = 1-4 and for Reynolds numbers Re = 3,000-10,000. The solution method of the governing transport equations is based on the modified hybrid scheme which produces very small truncation error. As a result of extensive computations, the complex flow patterns in the channel with two bends are clarified and the mechanisms of heat transfer are explained relating to the flow behaviors of separation, deflection, recirculation, and reattachment.

Amano, R. S.↗
NASA NTRS1984

Bending strength studies on hot-pressed silicon carbide

The 4-point bending strength of 4 grades of hot-pressed SiC was determined at different temperatures. With a transgranular mode of fracture the values for bending strength are retained up to high temperatures. For intergranular fracture the decrease of strength is governed by subcritical crack growth. The intergranular fracture is caused by a high content of silicate glassy phase at the grain boundaries of hot-pressed SiC.

Kriegesmann, J.↗
NASA NTRS1985

Stress-intensity factors for circumferential surface cracks in pipes and rods under tension and bending loads

The purpose of this paper is to present stress-intensity factors for a wide range of nearly semi-elliptical surface cracks in pipes and rods. The configurations were subjected to either remote tension or bending loads. For pipes, the ratio of crack depth to crack length (a/c) ranged from 0.6 to 1; the ratio of crack depth to wall thickness (a/t) ranged from 0.2 to 0.8; and the ratio of internal radius to wall thickness (R/t) ranged from 1 to 10. For rods, the ratio of crack depth to crack length also ranged from 0.6 to 1; and the ratio of crack depth to rod diameter (a/D) ranged from 0.05 to 0.35. These particular crack configurations were chosen to cover the range of crack shapes (a/c) that have been observed in experiments conducted on pipes and rods under tension and bending fatigue loads. The stress-intensity factors were calculated by a three-dimensional finite-element method. The finite-element models employed singularity elements along the crack front and linear-strain elements elsewhere. The models had about 6500 degrees of freedom. The stress-intensity factors were evaluated using a nodal-force method.

Raju, I. S.↗
NASA NTRS1985

Importance of anisotropic bending stiffnesses on buckling of symmetrically laminated composite plates loaded in compression

The differential equation governing buckling of symmetrically laminated composite plates loaded in compression is presented in nondimensional form. From this equation, nondimensional material coefficients are obtained and a nondimensional parameter is presented that is used to assess when anisotropic bending stiffnesses can be neglected in a buckling analysis. Results obtained using finite element analyses are presented that show how boundary conditions, aspect ratio, fiber orientation, stacking sequence, and thickness affect the importance of the anisotropic bending stiffnesses.

Nemeth, M. P.↗
NASA NTRS1986

Nonlinear bending-torsional vibration and stability of rotating, pretwisted, preconed blades including Coriolis effects

The coupled bending-bending-torsional equations of dynamic motion of rotating, linearly pretwisted blades are derived including large precone, second degree geometric nonlinearities and Coriolis effects. The equations are solved by the Galerkin method and a linear perturbation technique. Accuracy of the present method is verified by comparisons of predicted frequencies and steady state deflections with those from MSC/NASTRAN and from experiments. Parametric results are generated to establish where inclusion of only the second degree geometric nonlinearities is adequate. The nonlinear terms causing torsional divergence in thin blades are identified. The effects of Coriolis terms and several other structurally nonlinear terms are studied, and their relative importance is examined.

Subrahmanyam, K. B.↗
NASA NTRS1986

Stress-intensity factors for circumferential surface cracks in pipes and rods under tension and bending loads

The purpose of this paper is to present stress-intensity factors for a wide range of nearly semi-elliptical surface cracks in pipes and rods. The configurations were subjected to either remote tension or bending loads. For pipes, the ratio of crack depth to crack length (a/c) ranged from 0.6 to 1; the ratio of crack depth to wall thickness (a/t) ranged from 0.2 to 0.8; and the ratio of internal radius to wall thickness (R/t) ranged from 1 to 10. For rods, the ratio of crack depth to crack length also ranged from 0.6 to 1; and the ratio of crack depth to rod diameter (a/D) ranged from 0.05 to 0.35. These particular crack configurations were chosen to cover the range of crack shapes (a/c) that have been observed in experiments conducted on pipes and rods under tension and bending fatigue loads. The stress-intensity factors were calculated by a three-dimensional finite-element method. The finite-element models employed singularity elements along the crack front and linear-strain elements elsewhere. The models had about 6500 degrees of freedom. The stress-intensity factors were evaluated using a nodal-force method.

Raju, I. S.↗
NASA NTRS1986

The surface crack problem in an orthotropic plate under bending and tension

The elasticity problem for an infinite orthotropic flat plate containing a series of through and part-through cracks and subjected to bending and tension loads is considered. The problem is formulated by using Reissner's plate bending theory and considering three dimensional materials orthotropy. The Line-spring model developed by Rice and Levy is used to formulate the surface crack problem in which a total of nine material constants has been used. The main purpose of this study is to determine the effect of material orthotropy on the stress intensity factors, to investigate the interaction between two asymmetrically arranged collinear cracks, and to provide extensive numerical results regarding the stress intensity factors. The problem is reduced to a system of singular integral equations which is solved by using the Gauss-Chebyshev quadrature formulas. The calculated results show that the material orthotropy does have a significant effect on the stress intensity factor.

Wu, B. H.↗
NASA NTRS1987

An integrated finite element model of edge-delamination analysis for laminates due to tension, bending, and torsion loads

A two-dimensional finite-element model has been developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to various loads. This paper addresses the formulation, implementation, and verification of a suitable 'element for uniaxial tension, bending, and torsion', as well as parametric studies of the interlaminar stresses and strain energy release rates for various composite laminates. The study concentrates on establishing relationships of GI, GII, and GIII as functions of crack length and stacking sequence in laminates due to bending. Preliminary results of laminates subjected to torsional loads are included to increase the applicability and completeness of the present formulation.

Chan, W. S.↗
NASA NTRS1987

The surface crack problem in an orthotropic plate under bending and tension

The elasticity problem for an infinite orthotropic flat plate containing a series of through and part through cracks and subjected to bending and tension loads is considered. The problem is formulated by using Reissner's plate bending theory and considering three-dimensional material orthotropy. The Line-spring model developed by Rice and Levy is used to formulate the surface crack problem in which a total of nine material constants were used. The effects of material orthotropy on the stress intensity factors was determined, the interaction between two asymmetrically arranged collinear cracks was investigated, and extensive numerical results regarding the stress intensity factors are provided. The problem is reduced to a system of singular integral equations which is solved by using the Gauss-Chebyshev quadrature formulas. The calculated results show that the material orthotropy does have a significant effect on the stress intensity factor.

Wu, Bing-Hua↗
NASA NTRS1987

Femur-bending properties as influenced by gravity. V - Strength vs. calcium and gravity in rats exposed for 2 weeks

The dependence of gravitationally related changes in femur bone strength on the comparable changes in calcium content was investigated in rats exposed to chronic simulations of altered gravity from the 28th to 42nd day of age. Zero G was simulated by harness suspension and 3 G by centrifugation. Bone strength (S) was determined by bending (using modified quasi-static cantilever bending methods and equipment described by Wunder et al., 1977 and 1979) and Ca content (C, by mass pct) determined by atomic absorption spectrometry; results were compared with data obtained on both normal and harnessed control animals at 1 G. Multiple regression showed significant dependence of S upon earth's gravity, independent from C, for which there was no significant coefficient of partial regression. It is suggested that the lack of S/C correlation might have been due to the fact that considerable fraction of the calcium in these young, developing bones has not yet crystallized into the hydroxyapatite which provides strength.

Wunder, Charles C.↗
NASA NTRS1987

Flow in out-of-plane double S-bends

An experimental investigation of developing flows through a combination of out-of-plane S-bend ducts was conducted to gain insight into the redirection of flow in geometries similar to those encountered in practical aircraft wing-root intake ducts. The present double S-bend was fabricated by placing previously investigated S-ducts and S-diffusers in series and with perpendicular planes of symmetry. Laser-Doppler anemometry was employed to measure the three components of mean velocity, the corresponding rms quantities, and Reynolds stresses in the rectangular cross-section ducts. Due to limited optical access, only two mean and rms velocity components were resolved in the circular cross-section ducts. The velocity measurements were complemented by wall static pressure measurements. The data indicates that the flows at the exit are complex and asymmetric. Secondary flows generated by the pressure field in the first S-duct are complemented or counteracted by the secondary flows produced by the area expansion and the curvature of the S-diffuser. The results indicate the dominance of the inlet conditions and geometry upon the development of secondary flows and demonstrate that the flows are predominantly pressure-controlled. The pressure distribution caused by the duct geometry determines the direction and magnitude of the bulk flow while the turbulence dictates the mixing characteristics and profiles in the near wall region.

Schmidt, M. C.↗
NASA NTRS1988

Magnetohydrodynamic bending waves in a current sheet

The physical properties of MHD bending waves in an isothermal, compressible, low-beta, three-dimensional current sheet of finite thickness in which the magnetic field direction and strength varies are considered. The case of the wavenumber (k) to circular frequency ratio being greater than the Alfven velocity outside the layer (V sub A) corresponds to one-sided surface waves, and it is suggested that the heliospheric current sheet ripples are not this type of bending wave. The case of k/omega of less than V sub A describes the interaction of freely and obliquely propagating MHD waves with the layer, while the case of k/omega = V sub A describes an Alfven wave propagating parallel to but having no interaction with the layer.

Musielak, Z. E.↗
NASA NTRS1988

Effects of subcritical crack growth on fracture toughness of ceramics assessed in chevron-notched three-point bend tests

A numerical computational study was carried out to assess the effects of subcritical crack growth on crack stability in the chevron-notched three-point bend specimens. A power-law relationship between the subcritical crack velocity and the applied stress intensity were used along with compliance and stress-intensity relationships for the chevron-notched bend specimen to calculate the load response under fixed deflection rate and a machine compliance. The results indicate that the maximum load during the test occurs at the same crack length for all the deflection rates; the maximum load, however, is dependent on the deflection rate for rates below the critical rate. The resulting dependence of the apparent fracture toughness on the deflection rate is compared to experimental results on soda-lime glass and polycrystalline alumina.

Chao, L. Y.↗
NASA NTRS1988

A mixed-mode bending apparatus for delamination testing

A mixed-mode delamination test procedure was developed combining double cantilever beam mode I loading and end notch flexure mode II loading on a split unidirectional laminate. By loading the specimen with a lever, a single applied load simultaneously produces mode I and II bending loads on the specimen. This mixed mode bending (MMB) test was analyzed using both finite element procedures and beam theory to calculate the mode I and II components of strain energy release rate, G sub I and G sub II, respectively. The analyses showed that a wide range of G sub I/G sub II ratios could be produced by varying the applied load position on the loading lever. As the delamination extended, the G sub I/G sub II ratios varied by less than 5 percent. The simple beam theory equations were modified to account for the elastic interaction between the two arms of the specimen and to account for shear deformations. The resulting equations agreed closely with the finite element results and provide a basis for selection of G sub I/G sub II test ratios and a basis for computing the mode I and II components of measured delamination toughness. The MMB specimen analysis and test procedures were demonstrated using unidirectional laminates.

Crews, John H., Jr.↗
NASA NTRS1989

An analytical and experimental investigation of edge delamination in laminates subjected to tension, bending, and torsion

An integrated two-dimensional finite element was developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to uniaxial tension, bending, and torsion loads. Addressed are the formulation, implementation, and verification of the model. Parametric studies were conducted on the effect of Poisson's ratio mismatch between plies and the stacking sequence on interlaminar stress, and on the effect of delamination opening height and delamination length, due to bending, on strain energy release rate for various laminates. A comparison of strain energy release rates in all-graphite and graphite/glass hybrid laminates is included. The preliminary results of laminates subjected to torsion are also included. Fatigue tension tests were conducted on Mode 1 and mixed mode edge-delamination coupons to establish the relationship between fatigue load vs. onset of delamination cycle. The effect on the fatigue delamination onset of different frequencies (1 and 5 Hz) was investigated for glass, graphite,and their hybrid laminates. Although a 20 percent increase in the static onset-of-delamination strength and a 10 percent increase in ultimate strength resulted from hybridizing the all-graphite laminate with a 90 deg glass ply, the fatigue onset is lower in the hybrid laminate than in the all-graphite laminate.

Chan, Wen S.↗
NASA NTRS1989

Notch effects on room temperature tensile and bend properties of Ni3Al and Ni3Al+B

The notched mechanical properties of Ni3Al and Ni3Al+B prepared by powder metallurgy techniques have been determined in both tension and bending at room temperature. Tensile tests performed using double-notched specimens containing relatively blunt notches produced intergranular fracture in both Ni3Al and Ni3Al+B, with evidence of fracture initiating in an intergranular manner ahead of the blunt notch in both cases. Estimates of notched fracture toughness from bend tests and of local grain boundary fracture stress from the notched tensile tests suggest an increase in these values with boron addition.

Khadkikar, P. S.↗
NASA NTRS1990

Analysis and experiments for composite laminates with holes and subjected to 4-point bending

Analytical and experimental results are presented for composite laminates with a hole and subjected to four-point bending. A finite-plate analysis is used to predict moment and strain distributions for six-layer quasi-isotropic laminates and transverse-ply laminates. Experimental data are compared with the analytical results. Experimental and analytical strain results show good agreement for the quasi-isotropic laminates. Failure of the two types of composite laminates is described, and failure strain results are presented as a function of normalized hole diameter. The failure results suggest that the initial failure mechanism for laminates subjected to four-point bending are similar to the initial failure mechanisms for corresponding laminates subjected to uniaxial inplane loadings.

Shuart, M. J.↗
NASA NTRS1990

Analysis of delamination in fiber composite laminates out-of-plane under bending

Delamination in the form of cracking or separation between plies in an advanced fiber composite laminate is a problem of major concern. Both advanced analytical methods and advanced computational analyses are conducted to: (1) develop an asymptotic solution for a composite laminate subject to out-of-plane bending; (2) construct advanced singular finite elements in conjunction with the development of nonsingular elements for this bending problem; and (3) evaluate the delamination failure mechanics parameters and the subsequent modes of fracture. A parametric study was also conducted to evaluate the influences of various lamination parameters on the delaminated composites.

Wang, S. S.↗