Search NASA⌕ Search

SEARCH · Search NASA

Results for “Biomass flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Enhanced carbon-transfer and -utilization efficiencies achieved using membrane carbonation with gas sources having a range of CO 2 concentrations

The economic viability of microalgal biofuels relies on increasing productivity in a cost-effective manner. As microalgal biomass contains > 50% carbon, a high rate of CO 2 delivery is required for high productivity, and inefficient CO 2 delivery amplifies operating costs. Membrane carbonation using non-porous hollow fiber membranes can ideally deliver CO 2 without bubble formation and high carbon transfer efficiency. Because CO 2 streams from industrial resources are not 100% CO 2 , the buildup of inert gasses can significantly lower the CO 2 delivery rate when the distal end of the membrane is closed. To overcome the buildup of inert gases, we managed the distal end of the membranes with three different approaches: fully open end, restricted bleed valve, and restricted bleed valve with pH-actuated venting. For all approaches, CO 2 was delivered to membranes ondemand based on a pH set point. Evaluating a wide range of CO 2 concentrations (10% to 100%), we found that all approaches eliminated the buildup of inert gases, could maintain target pH values and gave the same biomass productivities and carbon distributions. However, carbon transfer efficiency depended on the operation of the distal end. Fully open-end operation gave a poor carbon transfer efficiency because of excessive loss of CO 2 from the distal end. However, restricting the exit flow rate to ≤4 cm 3 /min mitigated the problems of excessive CO 2 loss, but without incurring a large loss of CO 2 -delivery flux. For the continuous cultivation, combining a restricted bleed valve with pH-actuated venting improved the carbon-transfer efficiency and -utilization efficiencies up to 85% and 67%, respectively, with a sufficient CO 2 delivery flux.

42 ENGINEERING↗
DOE OSTI2026

Geographic_Distribution_of_Genotypes_with_Structural_Variant

Aninteractive mapshowing the geographic distribution ofPopulus trichocarpagenotypes carrying a deletion structural variant overlaid with Mount Rainier volcanic hazard zones. Hazard layers including lahar inundation zones and pyroclastic flow zones can be toggled on and off and geographic origins are searchable by genotype or river system using the search bar.

09 BIOMASS FUELS↗
DOE OSTI2025

Novel Preprocessing Techniques for Enhancing Flowability of Miscanthus

Purpose-grown energy crops possess significant potential as promising feedstocks for biofuel and biochemical production. However, similar to other biomass feedstocks, their utilization has been hindered by handling and feeding challenges such as clogging and segregation, which prevent biorefineries from operating at full capacity. These challenges arise primarily due to particle attributes including irregular shape, high flexibility, and high compressibility, leading to interlocking, high compaction, and significant friction under stress consolidation. To enhance operational reliability, it is crucial to focus on preprocessing techniques to address these issues, alongside accurately characterizing the mechanical and physical properties and flow performance of these feedstocks. This study investigates novel preprocessing techniques, including pelletization and torrefaction, to fundamentally alter these particle attributes and improve flowability. Miscanthus, an herbaceous energy crop, was the primary focus of this study. Samples were processed using a Forest Concepts Crumbler rotary shear system and an oscillating multi-stack screen bed to achieve two nominal (baseline) particle sizes: 6mm and 2mm. The study evaluated the efficiency and energy consumption of size reduction, revealing that while 2mm particles required more energy, they exhibited better flowability and higher yield strength compared to 6mm particles. Shear and compression tests assessed the material's shear strength, internal friction, and elastic modulus, while wedge-shaped hopper tests measured the critical arching distance and mass flow rate. The results provide valuable insights into the mechanical properties and processing efficiency of Miscanthus, contributing to the development of a preprocessing framework that enhances energy efficiency and material flowability in bioenergy production. However, further preprocessing and development are required to optimize this framework fully.

09 - BIOMASS FUELS↗
DOE OSTI2020

Achieving high hydrogen productivities of 20 L/L-day via microbial electrolysis of corn stover fermentation products

Microbial electrolysis cells have the potential to generate renewable hydrogen from underused waste streams, however current devices have not reached very large productivity targets using real waste products at any scale. This study used a waste from fermented corn stover known as corn stover fermentation product to reach performance metrics that could be commercialized, if adequately scaled. Average current densities in MECs with mature biofilms reached 17.9 +/- 1.6 A/m 2 at an organic loading rate of 30 grams of chemical oxygen demand per liter of anode volume per day (g/L-day), reaching a maximum current density of 27.2 +/- 2.9 A/m 2 . Hydrogen productivities reached 20.2 +/- 2.0 L of H 2 per L anode volume per day (L/L-day). These represent the highest current densities and highest hydrogen productivities using a complex feedstock in a microbial electrolysis cell. Organic acids and sugars present in untreated substrate were converted at high percentages in MECs, with most above 90% conversion, at organic loading rates of 10, 20, and 30 g/L-day. The effect of periodic high liquid flow rates through the anode on performance was assessed. These tests, called pulsing, showed that hydrogen productivities and current densities increased most dramatically as flow was pulsed every hour at a baseline flow rate of 0.3 mL/min. These productivities show promise for high performance systems, if adequate scale up can be achieved.

09 BIOMASS FUELS↗
DOE OSTI2021

Multiobjective Modular Biorefinery Configuration under Uncertainty

With increasing interest in using biomass as a raw material for fuel, the development of biorefineries is an active area of research. However, increasing market competition, uncertainty, and environmental concerns are a few of the challenges that need to be addressed. In this work, mathematical optimization formulations are proposed to address these challenges simultaneously. A multiobjective deterministic optimization framework is proposed to address economic and environmental objectives. A two-stage stochastic optimization framework is proposed to account for uncertainties in material flow and product yields. To model the environmental objective, an environmental risk metric is proposed. Finally, as modularization is gaining popularity in the process industry due to its ability to save capital cost because of standardization and reduce time to market, a formulation for simultaneously achieving modular process design and biorefinery configuration is proposed. Furthermore, the results demonstrate the efficacy of the proposed approach.

09 BIOMASS FUELS↗
DOE OSTI2024

Alternative electron pathways of photosynthesis power green algal CO2 capture

Abstract Microalgae contribute to about half of global net photosynthesis, which converts sunlight into the chemical energy (ATP and NADPH) used to transform CO2 into biomass. Alternative electron pathways of photosynthesis have been proposed to generate additional ATP that is required to sustain CO2 fixation. However, the relative importance of each alternative pathway remains elusive. Here, we dissect and quantify the contribution of cyclic, pseudo-cyclic, and chloroplast-to-mitochondrion electron flows for their ability to sustain net photosynthesis in the microalga Chlamydomonas reinhardtii. We show that (i) each alternative pathway can provide sufficient additional energy to sustain high CO2 fixation rates, (ii) the alternative pathways exhibit cross-compensation, and (iii) the activity of at least one of the three alternative pathways is necessary to sustain photosynthesis. We further show that all pathways have very different efficiencies at energizing CO2 fixation, with the chloroplast–mitochondrion interaction being the most efficient. Overall, our data lay bioenergetic foundations for biotechnological strategies to improve CO2 capture and fixation.

Biochemistry & Molecular Biology↗
DOE OSTI2023

A multiyear tropical Pacific cooling response to recent Australian wildfires in CESM2

The climate response to biomass burning emissions from the 2019–2020 Australian wildfire season is estimated from two 30-member ensembles using CESM2: one of which incorporates observed wildfire emissions and one that does not. In response to the fires, an increase in biomass aerosol burdens across the southern hemisphere is simulated through late 2019 and early 2020, accompanied by an enhancement of cloud albedo, particularly in the southeastern subtropical Pacific Ocean. In turn, the surface cools, the boundary layer dries, and the moist static energy of the low-level flow into the equatorial Pacific is reduced. In response, the intertropical convergence zone migrates northward and sea surface temperature in the Niño3.4 region cools, with coupled feedbacks amplifying the cooling. A subsequent multiyear ensemble mean cooling of the tropical Pacific is simulated through the end of 2021, suggesting an important contribution to the 2020–2022 strong La Niña events.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Optimization of Energy Flow through Synthetic Metabolic Modules and Regulatory Networks in a Model Photosynthetic Eukaryotic Microbe

Photosynthetic organisms have recently gained considerable attention for a role in development of renewable energy sources. Genome-enabled systems biology methods, coupled with functional and synthetic genomics, present opportunities to develop sustainable and economical applications such as fuel production within the next 10 to 15 years. However, optimization of light-driven metabolism for biomass or biofuel production will require a detailed systems biology understanding of photosynthetic processes and cellular metabolism. Genome-scale metabolic models (GEMs) are at the core of systems analysis of cellular processes and form a common organizational framework for analyses of data resulting from functional genomics experimental work and computational studies. Therefore, there is a clear demand for high quality photosynthetic model organisms and the appropriate computational tools that enable systems analysis of light-driven metabolism. Through research conducted we expanded the currently available repertoire of photosynthetic GEMs to include the commercially valuable model diatom Phaeoctylum tricornutum. Diatoms have a peculiar and distinct evolutionary footprint and represent a major eukaryotic lineage that is taxonomically and functionally distinct from green and red algae and vascular plants. Therefore, the true potential for light-driven metabolism aimed at biofuel production remains poorly understood at a systems level for a large subset of the global diversity of photosynthetic organisms. The metabolic capabilities of P. tricornutum were comparatively modeled with those from other photosynthetic groups in order to elucidate the occurrence of metabolic traits within and between phototrophs. Additionally, this research resulted in significant extension of the COnstraints Based Reconstruction and Analysis (COBRA) Toolbox to accommodate the crucial need for infrastructure required for ‘omics data integration and analysis in the context of genome-scale models. Therefore, the proposed research achieved two important goals. First, within the broad scope of photosynthetic organisms, we functionally compared and, as a result, identified cellular processes that require optimization in order to enable deployment as biofuel feedstock. Second, the proposed research resulted in development of key computational infrastructure, which can be further extended to other biological systems, that is currently lacking but necessary for multiple ‘omics data integration.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Optimal Pathways from Alternative Carbon Feedstocks to Organic Commodity Chemicals

The use of biogenic and waste feedstocks is a promising strategy to improve the chemical sector's supply chain resiliency and carbon intensity. To help inform research efforts that transform these feedstocks into industrial chemicals, we used a systematic analysis framework to consistently evaluate the economics and environmental impacts of >200 alternative production pathways for 51 organic commodity chemicals in the United States under an optimistic future scenario that reflects the potential upper bounds of process scalability, energy availability, and carbon uptake. Lower-impact and lower-cost alternative pathways were identified for all but three chemicals, with 75% using thermochemical routes and half leveraging existing manufacturing infrastructure. Scenario analysis shows that the ranking of these pathways for half of the assessed chemicals is particularly sensitive to carbon uptake assumptions and criteria prioritization (i.e., cost only, environmental impact only, or both), with changes in electricity grid mix, hydrogen source, and underlying mass and energy flow data proving less influential. Implementing alternative pathways for just 11 chemicals could support a transition to net-zero greenhouse gas emissions from chemical production by 2050, with 11% lower cost than business as usual, similar water requirements, quadrupled electricity demand, and the use of most available woody biomass. These findings provide an exploratory guide toward a future chemical industry that harnesses alternative feedstocks.

09 BIOMASS FUELS↗
DOE OSTI2023

Process Considerations for the Production of Hydrogen via Steam Reforming of Oxygenated Gases from Biomass Pyrolysis and Other Conversion Processes

Abstract In 2021, average CO 2 emissions was 9.7 g CO 2 /g H 2 produced, primarily based on steam methane reforming (SMR) technology that currently dominates hydrogen production. The substitution of natural gas (NG) and other fossil feedstocks in SMRs with renewable gases may be considered as an option for reducing greenhouse gas emissions. This analysis explores process impacts and constraints associated with the potential introduction of biogenic gases into SMRs. The results indicate that replacing NG in the fuel train of the SMR, followed by partial replacement of NG in the feed train may be a feasible approach. For the CO‐ and CO 2 ‐rich gas compositions assumed in this analysis the results indicate that feed train may accommodate up to 25 mole % of biogenic gases using allowances in existing designs and/or with small modifications, while maintaining similar hydrogen output. NG substitution in higher proportions require more major changes because of increased flow rates and heat exchange requirements in the system. Biogenic gases with lower CO 2 and higher calorific values are advantageous for NG substitution, and dry reforming using the CO 2 present in the feed gas can reduce steam consumption and increase process efficiency within limits where coking does not become a new constraint.

08 HYDROGEN↗
DOE OSTI2024

Testing- and Model- Based Optimization of Coal-fired Primary Heater Design for Indirect Supercritical CO 2 Power Cycles (Final Scientific and Technical Report)

The overall objective of this project was to perform the R&D necessary to mitigate the risk associated with the design of a primary heat exchanger for a solid-fired combustion system coupled with an indirect-fired closed-loop Brayton Cycle utilizing supercritical CO 2 . The key technological hurdle was the coupling of a solid-fuel firing system with the primary heater, which poses a singular challenge, which is the management of burner performance and operational conditions in a way to manage heat exchanger tube metal temperatures and temperature ramp rates in the absence of fluid phase change on the inside of the tubes. We designed and built the first ever pseudo power system employing a simple recuperated supercritical CO 2 closed-loop Brayton Cycle coupled to a solid-fuel fired system. Advanced coupled CFD and process modeling were used to design the primary heat exchanger (PHX), which consisted of both radiative and convective sections, to limit tube metal temperatures resulting from the heat release profile of the solid fuel flame near the radiative tubes. The heat exchanger was designed to produce finished CO 2 temperatures of 600 °C a pressure of 20.7 MPa and CO 2 flow of 5.5 kg/s. The constructed PHX was capable of 1.2 MWth heat uptake. During design of the PHX, the modeling showed that most variables influencing flame shape (burner stoichiometric ratio and register velocities and swirl) were not suitable to manage heat flux to the metal surfaces. This is because they substantially increased adiabatic flame temperature through the influence of localized stoichiometric ratio. Excess air and firing rate were the two most powerful variables that could be used to control tube surface temperatures. The coupled system was operated for a total of 407 hours, with the longest continuous run of 248 hours. For 62% of the operational time, the unit was unmanned and in automatic control. The fuels used for the testing included natural gas, two Utah Bituminous coals, woody biomass, and bagasse. During the testing we were able to verify the 1.2 MWth heat uptake and we operated at a finished CO 2 temperature of 607 °C and a pressure of 20.3 MPa simultaneously. The real-time corrosion rate of the Super 304H tube CO 2 surface in the region of the radiative section of the PHX were measured, at an approximate temperature of 550 °C. The two key variables related to corrosion rate are the pressure and flow rate of the CO 2 . A technoeconomic analysis was performed at a scale of 120 MWE. The updated analysis showed that the efficiency of an sCO 2 power producing plant will be related to the pressure drop of the PHX.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

VFA Biorefinery Design for Informed Production of Ground and Aviation Fuels

The rising demand for low-carbon intensity fuel options requires evaluation of a system which can support their production economically and sustainably. Volatile fatty acids (VFAs) ranging from C2 to C8 can be derived in high yield from arrested anaerobic digestion of biomass. This talk provides an overview of our work in which we upgrade wet waste-derived VFAs using ketonization to elongate their carbon backbone to reach a range relevant to jet or diesel fuels. Kinetic models were used to predict ketone profiles from varying VFA profiles, thereby informing potential carbon flow to either (a) mixed paraffins for use in diesel or aviation fuel, or (b) ethers for use in diesel fuel. To do this, the anticipated products were screened for critical fuel characteristics using predictive tools. The criteria for neat and blended bioblendstocks were chosen based on conventional petrofuel requirements, and they were applied to inform fuel targets, identify limiting characteristics, and guide conversion development. While paraffins can serve as either diesel or aviation fuels, the latter has stringent criteria which include a precise distillation curve range tied to carbon distribution. Fuels which fall outside this range typically fail to meet other property metrics, and as such flashpoint and viscosity were identified as potentially limiting properties of this VFA aviation fuel. However, paraffin fractions which fall outside aviation criteria may meet diesel fuel requirements, which are looser except for the flashpoint minimum. Flashpoint was also a concern for smaller VFA diesel ethers, which posed an additional oxygenate risk of high water solubility. This fuel-informed conversion design process was demonstrated through production of paraffins with reduced sooting as compared to petrodiesel (~34%), and increased renewable aviation fuel blend levels (>70%). VFA-derived ethers improved petrodiesel by increasing fuel autoignition quality by 56% and reducing sooting by 86%. These VFA aviation and diesel fuels could enable greenhouse gas (GHG) reductions of over 165% and 50%, respectively, relative to their purely fossil-derived counterparts. Collectively, this work provides (i) an overview of how we leveraged the flexibility of VFAs for fuel production; and (ii) insight into the potential of a VFA biorefinery to accommodate varied feed and fuel applications, while also considering the merit of tailored fuel production pathways and GHG reduction potential.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Low Temperature Oxidation of Methylpropyl Ether

Ethers are potential high-performance fuels that can be produced from renewable carbon sources such as biomass, but their combustion properties are not clearly understood. The cetane numbers (CN) for ethers, a measure of autoignition tendency, can range from less than 10 to greater than 100, and predictive tools based upon the molecular structures are desirable in order to focus fuel development research. In this study, we used molecular modeling, chemical kinetic modeling, and experimental measurements to understand the important reactions that lead to the autoignition of methylpropyl ether (MPE), a model for ethers containing alkyl chains long enough for intramolecular hydrogen transfer. These reactions are known to be important in the autoignition of alkanes and ethers and we propose to investigate the relationship between alkyl and ether reaction pathways. A reaction mechanism for MPE was created using MIT's Reaction Mechanism Generator (RMG) and G4 quantum calculation results and models were tested using the ChemKin Pro suite of software. Results from atmospheric pressure, flow tube reactor experiments and rapid compression machine (RCM) experiments were used to test the kinetic model and suggest refinements.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Continuous culture of anaerobic fungi enables growth and metabolic flux tuning without use of genetic tools

Anaerobic gut fungi (AGF) have potential to valorize lignocellulosic biomass owing to their diverse repertoire of carbohydrate-active enzymes (CAZymes). However, AGF metabolism is poorly understood, and no stable genetic tools are available to manipulate growth and metabolic flux to enhance production of specific targets, e.g., cells, CAZymes, or metabolites. Herein, a cost-effective, Arduino-based, continuous-flow anaerobic bioreactor with online optical density control is presented to probe metabolism and predictably tune fluxes in Caecomyces churrovis. Varying the C. churrovis turbidostat setpoint titer reliably controlled growth rate (from 0.04 to 0.20 h −1 ), metabolic flux, and production rates of acetate, formate, lactate, and ethanol. Bioreactor setpoints to maximize production of each product were identified, and all continuous production rates significantly exceed batch rates. Formate spike-ins increased lactate flux and decreased acetate, ethanol, and formate fluxes. The bioreactor and turbidostat culture schemes demonstrated here offer tools to tailor AGF fermentations to application-specific hydrolysate product profiles.

Agriculture↗
DOE OSTI2020

Kinetics Modeling for Design of Continuous Enzymatic Hydrolysis

Enzymatic hydrolysis of cellulose to monomeric sugars continues to be a limiting step in cost-effectively producing sugar and fermentation-based biofuels from biomass. In particular, the high cost of enzymes coupled with the long time-scale of reaction pose challenges to economic viability. Performing enzymatic hydrolysis in a continuous mode with enzyme recycle may provide a path towards substantially reduced costs for sugar production, but design and analysis are complicated by a lack of suitable kinetics models. Computationally attainable models, such as fractal-based models, require knowledge of the reaction-history of the biomass, and are thus only suitable for describing the batch reactions from which they are derived. Fundamental models, while potentially more generalizable, are often too computationally intensive to use in process or reactor modeling. In this work, a phenomenological rate model is proposed based on a two-phase substrate representation. Good agreement is seen between batch and continuous enzymatic hydrolysis (CEH) experiment data, which validates the model and enables us to solve for reactor design parameters, such as CEH reactor size and stream flow rates, based on process variables like yield. This model is integrated with techno-economic analysis software to explore economic sensitivities. Important design optimizations and tradeoffs are identified and quantified, including the relative cost imposed by rate slowdown from sugar inhibition versus the cost to remove and concentrate sugars at a lower concentration. It also identifies, high-leverage avenues for further exploration, such as increasing the maximum feasible solids concentration, and sustaining high membrane flux and reliability.

09 BIOMASS FUELS↗
DOE OSTI2022

Detailed modeling of hydrogen release and particle shrinkage during pyrolysis of inhomogeneous wood

Hydrogen release during pyrolysis of woody biomass is studied considering anisotropicity and inhomogeneity of wood structure. A new anisotropic shrinkage model is proposed based on the decomposition of main wood constituents, i.e., cellulose, hemicellulose, and lignin. The new shrinkage model can predict the temporal evolution of the wood structure, and the differences between axial and radial shrinkage during pyrolysis. The model agrees very well with several experimental data from the literature. Based on particle temperature during conversion, the pyrolysis is partitioned into four stages, and the hydrogen release and H 2 formation from each stage are investigated. Stage (IV) of pyrolysis, from 1000 to 1273 K, is found to be efficient for H 2 production owing to the production of considerable mass of H with a minimal amount of tar species. Furthermore, the char quality is found to be different at the end of stages (II), (III), and (IV), where around 67.7, 80.5, and 93.4% wt. of solid residue is made of carbon, respectively. The model is also used to explain how the heating rate affects the temperature distribution inside the particle and how it shifts the peak of hydrogen release. Finally, the pyrolysis of two inhomogeneous wood samples — a beech twig with bark and a beech dowel with growth rings — are investigated. The bark can affect the pyrolysis rate, products, and flow pattern inside the particle. The growth rings do not have a considerable effect on the pyrolysis rate and products, but they have a significant impact on the flow pattern. This has an important implication for char conversion studies where the internal surface area and porosity field distribution have a significant effect on the gasification and oxidation rates.

09 BIOMASS FUELS↗
DOE OSTI2020

Method of converting ethanol to higher alcohols

A method and catalyst for forming higher alcohols from lower alcohol feedstocks. In one application a highly selective and stable copper pseudo-single-atom supported on MgO—Al2O3 catalyst is provided which provides ethanol condensation to higher alcohols at ˜50% yields and ˜85% selectivity is demonstrated with stable catalyst lifetime over 500 hours in a continuous flow system. In some applications a Guerbet condensation process is further utilized to yield a higher alcohol at a selectivity of near ˜90%.

09 BIOMASS FUELS↗
DOE OSTI2024

Evaluation of a Process to Separate Ensiled Corn Grain and Stover for Improved Utilization as a Biomass Feedstock

Corn grain and chopped stover were stored anaerobically at 37% to 50% (w.b.) aggregate moisture content to create a unique biomass feedstock. However, after storage, the two fractions must be separated to accommodate different conversion pathways. In this work, a modified cleaning system from a grain combine harvester was evaluated to investigate its effectiveness in separating the grain from the stover. While this system has been purposefully built for this task, there is no previous literature on separating grain at high material other than grain (MOG) to grain ratios. Using this system, material was separated into four fractions: Grain, Tailings, Heavy MOG, and Light MOG. Subsamples were collected, oven dried, and then hydrodynamically separated to quantify the grain content in the four fractions. Several different configurations of air velocities, mass flow rate, material MOG: grain ratios, and sieve types and openings were investigated. Grain capture was defined as the fraction of the total grain dry mass collected in the grain and tailings fractions. In five experiments, the grain capture effectiveness varied from 89.2% to 99.4% on a dry basis. The dry basis foreign matter (FM) in the clean grain was 0.6% to 10.8%. As a result, the use of a modified combine cleaning system has the potential to be one step in a system to fractionate corn grain from stover (i.e., MOG) in a biorefinery that uses both starch and cellulose as biomass feedstocks.

09 BIOMASS FUELS↗