Search NASA⌕ Search

SEARCH · Search NASA

Results for “CLOSED LOOP SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

An Environment for Hardware-in-the-Loop Formation Navigation and Control Simulation

Recent interest in formation flying satellite systems has spurred a considerable amount of research in the relative navigation and control of satellites. Development in this area has included new estimation and control algorithms as well as sensor and actuator development specifically geared toward the relative control problem. This paper describes a simulation facility, the Formation Flying Testbed (FFTB) at NASA's Goddard Space Flight Center, which allows engineers to test new algorithms for the formation flying problem with relevant GN&C hardware in a closed loop simulation. The FFTB currently supports the injection of GPS receiver hardware into the simulation loop, and support for satellite crosslink ranging technology is at a prototype stage. This closed-loop, hardware inclusive simulation capability permits testing of navigation and control software in the presence of the actual hardware with which the algorithms must interact. This capability provides the navigation or control developer with a perspective on how the algorithms perform as part of the closed-loop system. In this paper, the overall design and evolution of the FFTB are presented. Each component of the FFTB is then described in detail. Interfaces between the components of the FFTB are shown and the interfaces to and between navigation and control software are described in detail. Finally, an example of closed-loop formation control with GPS receivers in the loop is presented and results are analyzed.

Burns, Rich↗
NASA NTRS2002

Software Development for the Hobby-Eberly Telescope's Segment Alignment Maintenance System using LABView

The software development for an upgrade to the Hobby-Eberly Telescope (HET) was done in LABView. In order to improve the performance of the HET at the McDonald Observatory, a closed-loop system had to be implemented to keep the mirror segments aligned during periods of observation. The control system, called the Segment Alignment Maintenance System (SAMs), utilized inductive sensors to measure the relative motions of the mirror segments. Software was developed in LABView to tie the sensors, operator interface, and mirror-control motors together. Developing the software in LABView allowed the system to be flexible, understandable, and able to be modified by the end users. Since LABView is built using block diagrams, the software naturally followed the designed control system's block and flow diagrams, and individual software blocks could be easily verified. LABView's many built-in display routines allowed easy visualization of diagnostic and health-monitoring data during testing. Also, since LABView is a multi-platform software package, different programmers could develop the code remotely on various types of machines. LABView s ease of use facilitated rapid prototyping and field testing. There were some unanticipated difficulties in the software development, but the use of LABView as the software "language" for the development of SAMs contributed to the overall success of the project.

Hall, Drew P.↗
DOE OSTI2025

Highly crystalline, low-ash, graphite from coal using an Fe 2 O 3 -based catalytic process with recovery and reuse of catalyst and process acid

This study presents a sustainable process for producing highly crystalline, low-ash graphite from sub-bituminous coal using an Fe 2 O 3 -based catalytic method. The process integrates coal mineral removal, catalyst regeneration, and reagent recycling into a closed-loop system. Acid-soluble Fe-residue and mineral impurities are eliminated from the solid graphite through HCl treatment, followed by hydrolytic distillation to regenerate Fe 2 O 3 and recover HCl for reuse. Coal-derived silica is removed with a KOH rinse, yielding low-ash graphite suitable for high-performance applications. The closed-loop catalytic graphitization, where the recovered Fe 2 O 3 and HCl are used in subsequent graphitization runs, produces graphite with a degree of graphitization exceeding 95%. The L a and L c crystallite sizes reach 65–78 nm and 44–48 nm, respectively, with BET surface areas of 4–10 m 2 /g and an ash content below 0.1 wt.%. Lithium-ion battery testing reveals that anodes fabricated with this graphite deliver an initial discharge capacity between 384.5 and 421.2 mAh/g, averaging 395.0 ± 19.1 mAh/g, along with initial coulombic efficiencies of 85.0–89.1%. After 100 discharge–charge cycles at 0.25C, reversible capacities remain between 358.8 and 369.7 mAh/g, while coulombic efficiency stays above 99.9%. The findings highlight that coal can serve as a viable precursor for high-quality graphite production under relatively mild conditions, avoiding the need for extreme temperatures or aggressive reagents such as hydrofluoric acid, commonly employed in conventional processes. This work demonstrates both technical feasibility and environmental benefits, emphasizing its potential to support large-scale, sustainable graphite production for applications such as lithium-ion batteries.

Catalytic graphitization↗
NASA NTRS1976

Dynamic analysis of a class of mixed lumped-distributed parameter systems via numerical techniques

The modeling via transfer matrices of mixed lumped-distributed parameter systems with feedback control is discussed and novel methods of obtaining information on the controlled system's dynamic response via numerical methods is presented. These methods utilize numerical searches in the complex plane for the roots of the transcendental characteristic equation to determine the closed loop system eigenvalues. The fast Fourier transform (FFT) algorithm is utilized but in the inverse fashion (from frequency domain to time domain). The information obtained is identical to that contained in a model in modal coordinates, and can be used to construct such a model. An interactive computer program to do the required calculation is described, as well as its application to a manipulator arm design problem.

Book, W. J.↗
NASA NTRS1982

Control technology development

The main objectives of the control technology development task are given in the slide below. The first is to develop control design techniques based on flexible structural models, rather than simple rigid-body models. Since large space structures are distributed parameter systems, a new degree of freedom, that of sensor/actuator placement, may be exercised for improving control system performance. Another characteristic of large space structures is numerous oscillatory modes within the control bandwidth. Reduced-order controller design models must be developed which produce stable closed-loop systems when combined with the full-order system. Since the date of an actual large-space-structure flight is rapidly approaching, it is vitally important that theoretical developments are tested in actual hardware. Experimental verification is a vital counterpart of all current theoretical developments.

Schaechter, D. B.↗
NASA NTRS1987

Simultaneous structural and control optimization via linear quadratic regulator eigenstructure assignment

A method for simultaneous structural and control design of large flexible space structures (LFSS) to reduce vibration generated by disturbances is presented. Desired natural frequencies and damping ratios for the closed loop system are achieved by using a combination of linear quadratic regulator (LQR) synthesis and numerical optimization techniques. The state and control weighing matrices (Q and R) are expressed in terms of structural parameters such as mass and stiffness. The design parameters are selected by numerical optimization so as to minimize the weight of the structure and to achieve the desired closed-loop eigenvalues. An illustrative example of the design of a two bar truss is presented.

Becus, G. A.↗
NASA NTRS1998

The Design of Stable Nonlinear Controllers for a Class of Nonlinear Plants Based on Neutral Networks

Extensive empirical evidence has been published in the literature to demonstrate the enormous potential of multilayer neural network controllers. In spite of these results, practical implementation of these control schemes has been held back by the lack of an analytical proof of the stability of the controlled system. The objective of this paper is to present a nonlinear control scheme based on multilayer neural networks for the control of a class of nonlinear plants. The stability of the closed loop system will be rigorously established.

Adetona, Olawale↗
NASA NTRS1988

Active control of transient rotordynamic vibration by optimal control methods

Although considerable effort has been put into the study of steady state vibration control, there are few methods applicable to transient vibration control of rotorbearing systems. In this paper optimal control theory has been adopted to minimize rotor vibration due to sudden imbalance, e.g., blade loss. The system gain matrix is obtained by choosing the weighting matrices and solving the Riccati equation. Control forces are applied to the system via a feedback loop. A seven mass rotor system is simulated for illustration. A relationship between the number of sensors and the number of modes used in the optimal control model is investigated. Comparisons of responses are made for various configurations of modes, sensors, and actuators. Furthermore, spillover effect is examined by comparing results from collocated and noncollocated sensor configurations. Results show that shaft vibration is significantly attenuated in the closed loop system.

Palazzolo, A. B.↗
NASA NTRS1972

Methods for utilizing maximum power from a solar array

A preliminary study of maximum power utilization methods was performed for an outer planet spacecraft using an ion thruster propulsion system and a solar array as the primary energy source. The problems which arise from operating the array at or near the maximum power point of its 1-V characteristic are discussed. Two closed loop system configurations which use extremum regulators to track the array's maximum power point are presented. Three open loop systems are presented that either: (1) measure the maximum power of each array section and compute the total array power, (2) utilize a reference array to predict the characteristics of the solar array, or (3) utilize impedance measurements to predict the maximum power utilization. The advantages and disadvantages of each system are discussed and recommendations for further development are made.

Decker, D. K.↗
NASA NTRS1989

Sequential design of discrete linear quadratic regulators via optimal root-locus techniques

A sequential method employing classical root-locus techniques has been developed in order to determine the quadratic weighting matrices and discrete linear quadratic regulators of multivariable control systems. At each recursive step, an intermediate unity rank state-weighting matrix that contains some invariant eigenvectors of that open-loop matrix is assigned, and an intermediate characteristic equation of the closed-loop system containing the invariant eigenvalues is created.

Shieh, Leang S.↗
NASA NTRS1990

Phase-Compensating System For Fiber-Optic Holography

Phase-compensating system controls relative phase of laser light emitted from two optical fibers. Stabilized for conventional holographic applications, or stepped through sequence of 90 degree phase shifts for phase-stepping holographic interferometry. Closed-loop system compensates for phase fluctuations caused by mechanical stresses and temperature changes in fibers, providing long-term phase stability and phase steps accurate to within 0.02 degrees. Controls environmental fluctuations in phases of light emitted by output fibers.

Mercer, Carolyn R.↗
NASA NTRS1987

Advancements in silicon web technology

Low defect density silicon web crystals up to 7 cm wide are produced from systems whose thermal environments are designed for low stress conditions using computer techniques. During growth, the average silicon melt temperature, the lateral melt temperature distribution, and the melt level are each controlled by digital closed loop systems to maintain thermal steady state and to minimize the labor content of the process. Web solar cell efficiencies of 17.2 pct AM1 have been obtained in the laboratory while 15 pct efficiencies are common in pilot production.

Hopkins, R. H.↗
NASA NTRS2014

Investigation of Bio-Regenerative Life Support and Trash-to-Gas Experiment on a 4-Month Mars Simulation Mission

Future crewed missions to other planets or deep space locations will require regenerative Life Support Systems (LSS) as well as recycling processes for mission waste. Constant resupply of many commodity materials will not be a sustainable option for deep space missions, nor will stowing trash on board a vehicle or at a lunar or Martian outpost. The habitable volume will decline as the volume of waste increases. A complete regenerative environmentally controlled life support system (ECLSS) on an extra-terrestrial outpost will likely include physico-chemical and biological technologies, such as bioreactors and greenhouse modules. Physico-chemical LSS do not enable food production and bio-regenerative LSS are not stable enough to be used alone in space. Mission waste that cannot be recycled into the bio-regenerative ECLSS can include excess food, food packaging, clothing, tape, urine and fecal waste. This waste will be sent to a system for converting the trash into high value products. Two crew members on a 120 day Mars analog simulation, in collaboration with Kennedy Space Centers (KSC) Trash to Gas (TtG) project investigated a semi-closed loop system that treated non-edible biomass and other logistical waste for volume reduction and conversion into useful commodities. The purpose of this study is to show how plant growth affects the amount of resources required by the habitat and how spent plant material can be recycled. Real-time data was sent to the reactor at KSC in Florida for replicating the analog mission waste for laboratory operation. This paper discusses the 120 day mission plant growth activity, logistical and plant waste management, power and water consumption effects of the plant and logistical waste, and potential energy conversion techniques using KSCs TtG technology.

Trash-to-Gas↗
NASA NTRS1973

A manual control theory analysis of vertical situation displays for STOL aircraft

Pilot-vehicle-display systems theory is applied to the analysis of proposed vertical situation displays for manual control in approach-to-landing of a STOL aircraft. The effects of display variables on pilot workload and on total closed-loop system performance was calculated using an optimal-control model for the human operator. The steep approach of an augmentor wing jet STOL aircraft was analyzed. Both random turbulence and mean-wind shears were considered. Linearized perturbation equations were used to describe longitudinal and lateral dynamics of the aircraft. The basic display configuration was one that abstracted the essential status information (including glide-slope and localizer errors) of an EADI display. Proposed flight director displays for both longitudinal and lateral control were also investigated.

Baron, S.↗
NASA NTRS2014

Investigation of Bio-Regenerative Life Support and Trash-To-Gas Experiment on a 4 Month Mars Simulation Mission

Future crewed missions to other planets or deep space locations will require regenerative Life Support Systems (LSS) as well as recycling processes for mission waste. Constant resupply of many commodity materials will not be a sustainable option for deep space missions, nor will storing trash on board a vehicle or at a lunar or Martian outpost. The habitable volume will decline as the volume of waste increases. A complete regenerative environmentally controlled life support system (ECLSS) on an extra-terrestrial outpost will likely include physico-chemical and biological technologies, such as bioreactors and greenhouse modules. Physico-chemical LSS do not enable food production and bio-regenerative LSS are not stable enough to be used alone in space. Mission waste that cannot be recycled into the bio-regenerative ECLSS can include excess food, food packaging, clothing, tape, urine and fecal waste. This waste will be sent to a system for converting the trash into the high value products. Two crew members on a 120 day Mars analog simulation, in collaboration with Kennedy Space Centers (KSC) Trash to Gas (TtG) project investigated a semi-closed loop system that treated non-edible biomass and other logistical waste for volume reduction and conversion into useful commodities. The purposes of this study are to show the how plant growth affects the amount of resources required by the habitat and how spent plant material can be recycled. Real-time data was sent to the reactor at KSC in Florida for replicating the analog mission waste for laboratory operation. This paper discusses the 120 day mission plant growth activity, logistical and plant waste management, power and water consumption effects of the plant and logistical waste, and potential energy conversion techniques using KSCs TtG reactor technology.

trash to gas↗
NASA NTRS1986

A computerized test system for thermal-mechanical fatigue crack growth

A computerized testing system to measure fatigue crack growth under thermal-mechanical fatigue conditions is described. Built around a servohydraulic machine, the system is capable of a push-pull test under stress-controlled or strain-controlled conditions in the temperature range of 25 to 1050 C. Temperature and mechanical strain are independently controlled by the closed-loop system to simulate the complex inservice strain-temperature relationship. A d-c electrical potential method is used to measure crack growth rates. The correction procedure of the potential signal to take into account powerline and RF-induced noises and thermal changes is described. It is shown that the potential drop technique can be used for physical mechanism studies and for modelling crack tip processes.

Marchand, N.↗