Results for “Conducted Emissions” — Page 12

NASA NTRSDate not supplied

Effect of Liner Cooling Flow on Combustor Emissions for Commercial Supersonics Technology

An overview is provided of a parametric study conducted to study the effect of liner cooling airflow rates on NOx emissions of a seven-element lean-direct injection (LDI) module with radial airflow main swirlers. The goal of the CFD study was to determine the increase in cooling flow rate at which the NOx emissions would exceed 20% of the predicted emissions with zero liner cooling flow. The Open version of the National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with a new LDI injection module design with radial airflow swirlers instead of axial airflow swirlers. CFD analysis with OpenNCC predicted a 20% increase in EINOx emissions was reached when the liner cooling airflow rate was increased to 15% of the baseline combustor airflow rate. The liner cooling flow rate was predicted to have a non-linear effect on increase in overall EINOx of the seven element LDI injection module.

CFD↗

NASA NTRS2004

Evaluation of a Mobile Phone for Aircraft GPS Interference

Measurements of spurious emissions from a mobile phone are conducted in a reverberation chamber for the Global Positioning System (GPS) radio frequency band. This phone model was previously determined to have caused interference to several aircraft GPS receivers. Interference path loss (IPL) factors are applied to the emission data, and the outcome compared against GPS receiver susceptibility. The resulting negative safety margins indicate there are risks to aircraft GPS systems. The maximum emission level from the phone is also shown to be comparable with some laptop computer's emissions, implying that laptop computers can provide similar risks to aircraft GPS receivers.

Nguyen, Truong X.↗

NASA NTRS1999

Durability, Performance, and Emission of Diesel Engines Using Carbon Fiber Piston and Liner

This report summarizes the research conducted by NC State University in investigating the durability, performance and emission of a carbon fiber piston and liner in our single cylinder research Diesel engine. Both the piston and liner were supplied to NC State University by NASA LaRC and manufactured by C-CAT under a separate contract to NASA LaRC. The carbon-carbon material used to manufacture the piston and liner has significantly lower thermal conductivity, coefficient of thermal expansion, and superior strength characteristics at elevated temperatures when compared to conventional piston materials such as aluminum. The results of the carbon-carbon fiber piston testing were compared to a baseline configuration, which used a conventional aluminum piston in a steel liner. The parameters measured were the brake specific fuel consumption, ignition delay, frictional horsepower, volumetric efficiency, and durability characteristics of the two pistons. Testing was performed using a naturally aspirated Labeco Direct Injection single cylinder diesel engine. Two test cases were performed over a range of loads and speeds. The fixed test condition between the aluminum and carbon-carbon piston configurations was the brake mean effective pressure. The measured data was the fuel consumption rate, volumetric efficiency, load, speed, cylinder pressure, needle lift, and exhaust gas temperature. The cylinder pressure, and fuel consumption, exhaust gas temperature, and needle lift were recorded using a National Instruments DAQ board and a PC. All test cases used Diesel no. 2 for fuel.

Afify, E. M.↗

NASA NTRS2026

A Study of Space Environment Effect on Highly Thermally Conductive Hybrid Carbon Fiber Polymer Composites

A set of novel highly thermally conductive hybrid carbon fiber (CF) polymer composites has been developed for lightweight thermal radiator applications in space missions. This study investigates the effects of the space environment on these materials following exposure in low-Earth orbit (LEO) during the Materials International Space Station Experiment (MISSE)-17 flight mission, where samples experienced 159 days of combined atomic oxygen (AO), ultraviolet (UV) radiation, high vacuum, space radiation and thermal cycling. Post-flight characterization included weight loss, surface morphology, thermo-optical properties, molecular structures, glass transition temperature, thermal degradation and thermal conductivity analyses. The pyrolytic graphite sheet (PGS) samples exhibited negligible weight loss, stable thermo-optical property, and only minor oxidation signature on the exposed surface. Although AO erosion of the epoxy polymer matrix was evident, carbon nanotube (CNT)-infused PGS/CF epoxy composites retained high thermal emissivity and preserved their high thermal conductivities. These results demonstrate that the novel highly thermally conductive hybrid CF composites possess strong environmental resilience and are promising candidates for lightweight thermal radiators and thermal management components in future space exploration missions.

Space Environment↗

NASA NTRS1995

Aircraft Emission Inventories Projected in Year 2015 for a High Speed Civil Transport (HSCT) Universal Airline Network

This report describes the development of a three-dimensional database of aircraft fuel burn and emissions (fuel burned, NOx, CO, and hydrocarbons) from projected fleets of high speed civil transports (HSCT's) on a universal airline network.Inventories for 500 and 1000 HSCT fleets, as well as the concurrent subsonic fleets, were calculated. The objective of this work was to evaluate the changes in geographical distribution of the HSCT emissions as the fleet size grew from 500 to 1000 HSCT's. For this work, a new expanded HSCT network was used and flights projected using a market penetration analysis rather than assuming equal penetration as was done in the earlier studies. Emission inventories on this network were calculated for both Mach 2.0 and Mach 2.4 HSCT fleets with NOx cruise emission indices of approximately 5 and 15 grams NOx/kg fuel. These emissions inventories are available for use by atmospheric scientists conducting the Atmospheric Effects of Stratospheric Aircraft (AESA) modeling studies. Fuel burned and emissions of nitrogen oxides (NOx as NO2), carbon monoxide, and hydrocarbons have been calculated on a 1 degree latitude x 1 degree longitude x 1 kilometer attitude grid and delivered to NASA as electronic files.

Baughcum, Steven L.↗

NASA NTRS1996

Scheduled Civil Aircraft Emission Inventories for 1976 and 1984: Database Development and Analysis

This report describes the development of a three-dimensional database of aircraft fuel burn and emissions (fuel burned, NOx, CO, and hydrocarbons) from scheduled commercial aircraft for four months (February, May, August, and November) of 1976 and 1984. Combining this data with earlier published data for 1990 and 1992, trend analyses for fuel burned, NOx, carbon monoxide, and hydrocarbons were calculated for selected regions (global, North America, Europe, North Atlantic, and North Pacific). These emissions inventories are available for use by atmospheric scientists conducting the Atmospheric Effects of Aviation Project (AEAP) modeling studies. Fuel burned and emissions of nitrogen oxides (NOx as NO2), carbon monoxide, and hydrocarbons have been calculated on a 1 degree latitude x 1 degree longitude x 1 kilometer altitude grid and delivered to NASA as electronic files.

Baughcum, Steven L.↗

NASA NTRS1996

Scheduled civil aircraft emission inventories for 1992: Database development and analysis

This report describes the development of a three-dimensional database of aircraft fuel burn and emissions (fuel burned, NOx, CO, and hydrocarbons) from scheduled commercial aircraft for each month of 1992. The seasonal variation in aircraft emissions was calculated for selected regions (global, North America, Europe, North Atlantic, and North Pacific). A series of parametric calculations were done to quantify the possible errors introduced from making approximations necessary to calculate the global emission inventory. The effects of wind, temperature, load factor, payload, and fuel tankering on fuel burn were evaluated to identify how they might affect the accuracy of aircraft emission inventories. These emissions inventories are available for use by atmospheric scientists conducting the Atmospheric Effects of Aviation Project (AEAP) modeling studies. Fuel burned and emissions of nitrogen oxides (NOx as N02), carbon monoxide, and hydrocarbons have been calculated on a 1 degree latitude x 1 degree longitude x 1 kilometer altitude grid and delivered to NASA as electronic files.

Baughcum, Steven L.↗

NASA NTRS1998

Year 2015 Aircraft Emission Scenario for Scheduled Air Traffic

This report describes the development of a three-dimensional scenario of aircraft fuel burn and emissions (fuel burned, NOx, CO, and hydrocarbons)for projected year 2015 scheduled air traffic. These emission inventories are available for use by atmospheric scientists conducting the Atmospheric Effects of Aviation Project (AEAP) modeling studies. Fuel burned and emissions of nitrogen oxides (NOx as NO2), carbon monoxides, and hydrocarbons have been calculated on a 1 degree latitude x 1 degree longitude x 1 kilometer altitude grid and delivered to NASA as electronic files.

Baughcum, Steven L.↗

NASA NTRS1998

Aircraft Emission Scenarios Projected in Year 2015 for the NASA Technology Concept Aircraft (TCA) High Speed Civil Transport

This report describes the development of a three-dimensional database of aircraft fuel burn and emissions (fuel burned, NOx, CO, and hydrocarbons) from projected fleets of high speed civil transports (HSCTs) on a universal airline network. Inventories for 500 and 1000 HSCT fleets, as well as the concurrent subsonic fleets, were calculated. The HSCT scenarios are calculated using the NASA technology concept airplane (TCA) and update an earlier report. These emissions inventories are available for use by atmospheric scientists conducting the Atmospheric Effects of Stratospheric Aircraft (AESA) modeling studies. Fuel burned and emissions of nitrogen oxides (NOx as NO2), carbon monoxide, and hydrocarbons have been calculated on a 1 degree latitude x 1 degree longitude x 1 kilometer pressure altitude grid and delivered to NASA as electronic files.

Baughcum, Steven L.↗

NASA NTRS2007

High Pressure Low NOx Emissions Research: Recent Progress at NASA Glenn Research Center

In collaboration with U.S. aircraft engine companies, NASA Glenn Research Center has contributed to the advancement of low emissions combustion systems. For the High Speed Research Program (HSR), a 90% reduction in nitrogen oxides (NOx) emissions (relative to the then-current state of the art) has been demonstrated in sector rig testing at General Electric Aircraft Engines (GEAE). For the Advanced Subsonic Technology Program (AST), a 50% reduction in NOx emissions relative to the 1996 International Civil Aviation Organization (ICAO) standards has been at demonstrated in sector rigs at both GEAE and Pratt & Whitney (P&W). During the Ultra Efficient Engine Technology Program (UEET), a 70% reduction in NOx emissions, relative to the 1996 ICAO standards, was achieved in sector rig testing at Glenn in the world class Advanced Subsonic Combustion Rig (ASCR) and at contractor facilities. Low NOx combustor development continues under the Fundamental Aeronautics Program. To achieve these reductions, experimental and analytical research has been conducted to advance the understanding of emissions formation in combustion processes. Lean direct injection (LDI) concept development uses advanced laser-based non-intrusive diagnostics and analytical work to complement the emissions measurements and to provide guidance for concept improvement. This paper describes emissions results from flametube tests of a 9- injection-point LDI fuel/air mixer tested at inlet pressures up to 5500 kPa. Sample results from CFD and laser diagnostics are also discussed.

Chi-Ming, Lee↗

NASA NTRS2008

NASA Glenn High Pressure Low NOx Emissions Research

In collaboration with U.S. aircraft engine companies, NASA Glenn Research Center has contributed to the advancement of low emissions combustion systems. For the High Speed Research Program (HSR), a 90% reduction in nitrogen oxides (NOx) emissions (relative to the then-current state of the art) has been demonstrated in sector rig testing at General Electric Aircraft Engines (GEAE). For the Advanced Subsonic Technology Program (AST), a 50% reduction in NOx emissions relative to the 1996 International Civil Aviation Organization (ICAO) standards has been demonstrated in sector rigs at both GEAE and Pratt & Whitney (P&W). During the Ultra Efficient Engine Technology Program (UEET), a 70% reduction in NOx emissions, relative to the 1996 ICAO standards, was achieved in sector rig testing at Glenn in the world class Advanced Subsonic Combustion Rig (ASCR) and at contractor facilities. Low NOx combustor development continues under the Fundamental Aeronautics Program. To achieve these reductions, experimental and analytical research has been conducted to advance the understanding of emissions formation in combustion processes. Lean direct injection (LDI) concept development uses advanced laser-based non-intrusive diagnostics and analytical work to complement the emissions measurements and to provide guidance for concept improvement. This paper describes emissions results from flametube tests of a 9-injection-point LDI fuel/air mixer tested at inlet pressures up to 5500 kPa. Sample results from CFD and laser diagnostics are also discussed.

Tacina, Kathleen M.↗

NASA NTRS1973

Emission-line stars in the Chamaeleon T association.

Objective-prism spectrum surveys conducted in 1962 and in 1970 reveal 32 stars showing H-alpha emission in the region of the Chamaeleon T association. Twelve of these stars show variations in either continuum intensity or H-alpha intensity. The magnitudes range from V equals 8.4 (spectrum B9.5 Ve) to approximately 16. Slit spectra have been obtained of 13 stars. Seven show classifiable absorption-line spectra, four show completely veiled continua, and two lack blue spectra. The veiling is strongly correlated with variability. The second brightest emission-line star, CD - 76 486, shows significant spectrum variations between 1962 and 1972.

Henize, K. G.↗

NASA NTRS1983

NASA advanced low emissions combustor program

The purpose of this program is to conduct combustion tests on lean, premixed, and prevaporized (LPP) combustor concepts designed for use in commercial aircraft engines to attain improved performance, durability, and lower pollutant emissions levels relative to current technology combustor designs. Four full annular combustors were designed for the CF6-50 engine. These concepts utilize premixing of the fuel and air, variable geometry, and fuel staging to control the equivalence ratios of the burning zone. The testing is being conducted on these four full annular combustors over a wide range of operating conditions at pressures up to actual subsonic cruise (1.16 MPa). The test results for the most promising of these combustor concepts are reported in this paper.

Goyal, A.↗

NASA NTRS1995

CAE for thermal management of aerospace electronic boards using the BETAsoft program

Aerospace electronic boards require special attention to thermal management due to constraints such as their need to be light, small, and maintain high power densities. Also, cooling is mainly through conductive and radiative modes with minor or negligible convective cooling. Due to these particular requirements, thermal design has become an integrated part of the electronic design process in order to avoid expensive repeat prototyping and to ensure high reliability. To achieve high speed simulations, the BETAsoft code uses semi-empirical formulations and an advanced finite difference scheme that incorporates local adaptive grids. Detailed conduction, convection and radiation heat transfer is considered. Various benchmark verifications of the software simulation compared to infrared images typically prove to be within 10% of each other. The thermal analysis of a sample avionic card in a natural convection environment is shown. Then, the individual effects of attaching metal screws to the casing, increasing radiative emissivities of the casing, increasing the conductance of the wedge lock, adding an aluminum core to the board, adding metal strips in board layers, inserting conduction pads under components, and adding heat sinks to components are demonstrated.

Bobish, Kimberly↗

NASA NTRSDate not supplied

Comparing the Regional Variability of Emission Factors of Greenhouse Gases Over Different Landscape During FIREX-AQ Campaign

Biomass burning (wildfires, prescribed and agricultural burning) is one of the major sources of trace gases and particulate emissions and annual variability in growth rates. Biomass burning can impact local, regional, and global air quality, as well as climate. Measurements of emissions from biomass burning are crucial to a better understanding of how it influences and interacts with biogeochemical cycles. High resolution in-situ measurements were recorded onboard the NASA DC-8 aircraft during the FIREX-AQ (Fire Influence on Regional to Global Environments and Air Quality) airborne field campaign July-September, 2019, which was conducted over the continental U.S. Fire emission factors (EF) are essential input for emissions models used to develop biomass burning emission inventories. Here we present the Emission Ratio (ER), MCE (Modified Combustion Efficiency), and EF (Emission Factor) of CO2, CO, and CH4, which constitute the majority of carbon emitted from the wildland, prescribed, and agricultural fires. EFCO2, EFCO, and EFCH4 from the Wildland fires at Williams Flats, WA (primarily Douglas Fir, Ponderosa pine, wheatgrass: 50-75%), ranged from 1527 – 1820 g/kg (Avg. 1641±42), 6.5 – 174.1 g/kg (110.5±24.1), and 0.7 – 11.3 g/kg (6.2±1.9), respectively. EFs from the Arizona CASTLE fire, with somewhat different fuel sources (primarily Ponderosa pine, Douglas fir: 40-70%) ranged from 1266 – 1667 g/kg (1596±59), 99.5 – 344.5 g/kg (136.7±36.8), and 0.4 – 9.2 g/kg (7.2±1.7), respectively. Another primary driver of EFs is likely fire weather. Detailed variability of greenhouse gas EFs will be examined and presented in accordance with different fuels and fire conditions at burned areas, specifically within unique wildland and croplands, using the FCCS (Fuel Characteristic Classification System) 30m land cover identification and the Cropland Data Layer (CDL).

Biomass burning↗

NASA NTRSDate not supplied

Comparing the regional variability of emission factors of greenhouse gases over different landscape during FIREX-AQ campaign

Biomass burning (wildfires, prescribed and agricultural burning) is one of the major sources of trace gases and particulate emissions and annual variability in growth rates. Biomass burning can impact local, regional, and global air quality, as well as climate. Measurements of emissions from biomass burning are crucial to a better understanding of how it influences and interacts with biogeochemical cycles. High resolution in-situ measurements were recorded onboard the NASA DC-8 aircraft during the FIREX-AQ (Fire Influence on Regional to Global Environments and Air Quality) airborne field campaign July-September, 2019, which was conducted over the continental U.S. Fire emission factors (EF) are essential input for emissions models used to develop biomass burning emission inventories. Here we present the Emission Ratio (ER), MCE (Modified Combustion Efficiency), and EF (Emission Factor) of CO2, CO, and CH4, which constitute the majority of carbon emitted from the wildland, prescribed, and agricultural fires. EFCO2, EFCO, and EFCH4 from the Wildland fires at Williams Flats, WA (primarily Douglas Fir, Ponderosa pine, wheatgrass: 50-75%), ranged from 1527 – 1820 g/kg (Avg. 1641±42), 6.5 – 174.1 g/kg (110.5±24.1), and 0.7 – 11.3 g/kg (6.2±1.9), respectively. EFs from the Arizona CASTLE fire, with somewhat different fuel sources (primarily Ponderosa pine, Douglas fir: 40-70%) ranged from 1266 – 1667 g/kg (1596±59), 99.5 – 344.5 g/kg (136.7±36.8), and 0.4 – 9.2 g/kg (7.2±1.7), respectively. Another primary driver of EFs is likely fire weather. Detailed variability of greenhouse gas EFs will be examined and presented in accordance with different fuels and fire conditions at burned areas, specifically within unique wildland and croplands, using the FCCS (Fuel Characteristic Classification System) 30m land cover identification and the Cropland Data Layer (CDL).

Biomass burning↗

NASA NTRS1988

Space Shuttle Main Engine radio frequency emissions

Several approaches to develop a diagnostics system for monitoring the operational health of the Space Shuttle Main Engine (SSME) are being evaluated. The ultimate goal is providing protection for the SSME as well as improving ground and flight test techniques. One scenario with some potential is measuring radio frequency (RF) emissions (if present) in the exhaust plume and correlating the data to engine health. An RF emissions detection system was therefore designed, the equipment leased, and the components integrated and checked out to conduct a quick-look investigation of RF emissions in the SSME exhaust plume. The system was installed on the A-1 Test Stand at Stennis Space Center, MS, and data were successfully acquired during SSME firings from May 3 to September 15, 1988. The experiments indicated that emitted radiation in the RF (20 to 470 MHz) spectrum definitely exists in the SSME exhaust plume, and is of such magnitude that it can be distinguished during the firing from background noise. Although additional efforts are necessary to assess the merit of this approach as a health monitoring technique, the potential is significant, and additional studies are recommended.

Rester, A. W.↗

NASA NTRS1990

H I absorption limits and emission mapping for high-velocity clouds

Systematic emission and absorption surveys have been conducted for high-velocity H I in the direction of 63 bright continuum sources. High-velocity emisison is detected along 18 of these 63 directions with a threshold about a factor of 2 better than previous, much more extensive surveys. No high-velocity absorption was found in any of the directions. The sky distribution of the high-velocity emission and the column density distribution agree with larger surveys. Detailed emission maps in the vicinity of each continuum source show that the variations in column density within a high-velocity cloud are similar to the variations between high-velocity clouds. A previously discovered high-velocity cloud at high galactic latitude, in the direction of part of the Virgo Cluster of galaxies, was mapped. This small cloud is moving away from the galactic plane at v greater than 30 km/s and is probably not self-gravitating.

Colgan, Sean W. J.↗